Français dropdown-ico

Manuel d’utilisation Gossen R2601

40 pages 0.16 mb
Télécharger

Aller à la page of 40

Summary
  • Gossen R2601 - page 1

    Interface description R2600 / R2601 DIN Draft 19244 Interface 3-348-815-15 6/11.03 ...

  • Gossen R2601 - page 2

    ...

  • Gossen R2601 - page 3

    CONTENTS Page Page GOSSEN METRAWATT GMBH 3 1 General ...................................................................................... 4 1.1 Interface hardware ............................................................. 4 1.2 Communications protocol ................................................... 4 1.3 How to connect the interface ...... ...

  • Gossen R2601 - page 4

    GOSSEN METRAWATT GMBH 4 1 General 1.1 Interface hardware T o communicate with a host computer , an SPS, etc., the controller s R2600 / 01 must be equipped with marking F1. In this case, t he controllers are equipped with a serial interf ace ha ving the following data: • Level types RS-232 and RS-485 (two-wire) in the unit sele ctable • Baud rat ...

  • Gossen R2601 - page 5

    GOSSEN METRAWATT GMBH 5 1.3 How to connect the interface 1.3.1 RS-232 connection When using the a RS-232 interface, only one R260 0/01 can be conne cted to a master ( e.g. PC), for example, for pre-loading the u nit with user -specific data. Depending upon the driver software, the jumpers on the master side can be omitte d and/or can be diff erent. ...

  • Gossen R2601 - page 6

    GOSSEN METRAWATT GMBH 6 1.3.2 RS-485 connection When using a RS-485 interface, as many as 32 equipm ent (R2600/01 and others) can be connected to the bus. Thereby , all terminals A, B and/or C are inte rconnected in parallel. The wiring must be made from equipment to equipment and m u st not be a sta r con- nection. With longer bus lines (longer th ...

  • Gossen R2601 - page 7

    GOSSEN METRAWATT GMBH 7 Following, the master may only become active again, when – it receives a reply telegram fr om the addressed equip ment and the specified wait time after a reply telegram (t aw) has elapse d, or – the maximum specified response delay time (t av ) has elapsed. Within a telegram, pauses of limited duration (t zv = character ...

  • Gossen R2601 - page 8

    GOSSEN METRAWATT GMBH 8 2 T elegr am structure All telegrams consist of one of 3 sets in both request and reply direction, they differ in their princip al structure. Their use is fixed for each interface function of the R2600/01. Structure and use of the set types are describ ed as follows. 2.1 Short set Short sets are used on the request side (fro ...

  • Gossen R2601 - page 9

    GOSSEN METRAWATT GMBH 9 2.2 Control set The R2600/01 uses control sets on the request side only. They se rve to request all equipment data that cannot be requested via a short set because a detailed specification is required for them. Principal construction control set Character No. Contents Meaning Remarks 1 68h Start character 2 3 and/or 6 Length ...

  • Gossen R2601 - page 10

    GOSSEN METRAWATT GMBH 10 2.3 Long set The R2600/01 uses long sets to transmit instructions and parame ters to the equipment and to receive data from the equipment. Principal construction long set Character No. Contents Meaning Remark 1 68h Start character 2 Length Number of characters fr om equipment address to checksum exclusive 3 Length (repeat) ...

  • Gossen R2601 - page 11

    GOSSEN METRAWATT GMBH 11 2.4 Function and value range of the format characters 2.4.1 Equipment address • 0 ... 250 Range for individual equipme nt addresses = interface address Addr • 255 All equipment connected to a bus can simultaneously be addressed under this address. Data and inst ructions entered with this address are accepted by all equi ...

  • Gossen R2601 - page 12

    GOSSEN METRAWATT GMBH 12 2.4.2.2 Function coding of the function field (FF) in response direction Bit No. Function Valu e Meaning 0 ... 2 Reserved 0, 0, 0 (fixed) 3 Request disable 0 1 Instruction executed, equipment ready Equipment not ready for this instruction, event ually repeat instruction 4 Instruction acknowledgement 0 1 Instruction executed ...

  • Gossen R2601 - page 13

    GOSSEN METRAWATT GMBH 13 2.4.3 Parameter index (PI) The type of the data to be tran smitted is defined via the pa rameter index. The "PI" charac ter is inte rprete d as follows: Functionally used data and/or setting para meters of an equipment are combined in the main parameter groups. Only those paramete r indices docu- mented in section ...

  • Gossen R2601 - page 14

    GOSSEN METRAWATT GMBH 14 2.5 Criteria for the validity of a r equest telegram The R2600/01 checks the characters of the telegrams received in accordance with the following tables: If incorrect values are received for FF, PI and PS, the R2600/0 1 responds with a short set with set transmission error bit. If the user data is entered beyond its specif ...

  • Gossen R2601 - page 15

    GOSSEN METRAWATT GMBH 15 3 T elegr am contents R2600/0 1 3.1 Equipment reset The addressed equipment performs a hardwa re reset same as in the case of a sh ort interruption of the au xiliary voltage. Example: Equipment address = 2 3.2 Interrogation: Equipment OK? The addressed equipment show s the f unction field only: Example: Equipment address = ...

  • Gossen R2601 - page 16

    GOSSEN METRAWATT GMBH 16 3.3 Request for cycle data You will get the most important measuring and output values of the controller in one data package. Cyclic requests of these values are thus made possible in compact form (short set request. Example: Equipment address = 2 See 2.4.2.2 for contents of the function field (FF) The 7 characters of the c ...

  • Gossen R2601 - page 17

    GOSSEN METRAWATT GMBH 17 3.4 Request for event data The event date, combined in 2 words, contain al l erro r messages and al arms of the equ ipment. They can be called up via short se t to iden tify a special error. This request can be made asynchronous, for ex ample, if the service request bit (colle cted errors) was set before in any random respo ...

  • Gossen R2601 - page 18

    GOSSEN METRAWATT GMBH 18 Character Bit No. Meaning Display on equipment Rem ark 1. 0 Sensor breakage measuring circuit 2 Status error word 1 (control loop) 1 Wrong polarity m easuring circuit 2 2 Analog error 3 Sensor breakage measuring circuit 1 4 Wrong polarity m easuring circuit 1 5 Low limit 1 fallen below Associated data display flashes 6 Low ...

  • Gossen R2601 - page 19

    GOSSEN METRAWATT GMBH 19 3. 0 Sensor error position readback Error status word 2 (heating current monitor , equipment) 1 Sensor error heating current 2 3 4 Heating current not "off" with po sitioning signal switched off Current display flashes 5 Heating current < 80 % of the set point of the heating curren t with active positioning sig ...

  • Gossen R2601 - page 20

    GOSSEN METRAWATT GMBH 20 3.5 Request data from R2600/01 This communication makes it possible to request all values, parameters, c onfigur ations, states and equipment markings. Thereby , the data is indi vidually addressed per para meter index. See section 4 for the comp lete list of all parameter indices. 3.5.1 Request an equipment specification T ...

  • Gossen R2601 - page 21

    GOSSEN METRAWATT GMBH 21 3.5.2 Request for a temperature param eter , for example The parameter index is not 3xh, thus the characters "from/to channel" and "receipt No." = 1, 1, 0 are contained in the control and long set. Example: Request for the maximum selecta ble set point ( SP H ) of the R2600/01 with address = 33 = 21h (se ...

  • Gossen R2601 - page 22

    GOSSEN METRAWATT GMBH 22 3.6 Send data to R2600/01 This communication makes it possible to set all parameters, configurations and operati ng states which can be changed via operat ion. Thereb y , the data is individually addressed per pa rameter index. See section 4 fo r the complete list of all parame ter indices. There is no protection against ov ...

  • Gossen R2601 - page 23

    GOSSEN METRAWATT GMBH 23 See 2.4.2.2 for the contents of the function field (FF) The first character of the data block is th e configuration "sensor type". The second character (B ma rking) cannot be stored, bu t a cha racter (an y , e.g. 00h) must be sent. 3.6.2 Send a control parameter , for example The parameter index (PI) is not 3xh, ...

  • Gossen R2601 - page 24

    GOSSEN METRAWATT GMBH 24 4 Parameter indices of the equipment paramete rs For a request and/or transmission of data from and/or to the R2600/01, not only the parameter index for the individual data but also the format and thus the length of the data block in th e long set are of interest. From the column "Format" of the parame ter tables ...

  • Gossen R2601 - page 25

    GOSSEN METRAWATT GMBH 25 03h Second set point ± 15 bits (4.1.2) SP L ... SP H 04h High limit for relay A2 ± 15 bits (4.1.2) Same as PI = 01h Same as PI = 01h 05h Low limit for relay A2 ± 15 bits (4.1.2) Same as PI = 01h Same as PI = 01h 06h Low set point ± 15 bits (4.1.2) X1 ... SP H For fixed value controller , slave controller –MBU/2 ... SP ...

  • Gossen R2601 - page 26

    GOSSEN METRAWATT GMBH 26 4.1.2 Unit of the temperature parameters The unit of the temperature parameters depends upon – the range marking B1 ... B5 of the equipment (see PI = 33h), – the configured sensor type (see PI = 33h) and – the configured unit of the sensor (see PI = 32h). With standard signal (B2, B5) and Pt100 with 0.1 ° display , t ...

  • Gossen R2601 - page 27

    GOSSEN METRAWATT GMBH 27 4.1.3 T able of measuring ranges Sensor type Lower range limit X1 Upper range limit X2 Range span MBU Code Kind Ty p e in °C in °F in °C in °F in °C in °F 0 TC J –18 0 850 1562 868 1562 1 L –18 0 850 1562 868 1562 2 K –18 0 1200 2192 1218 2192 3 B 0 32 1820 3308 1820 3276 4 S –18 0 1770 3218 1788 3218 5 R –1 ...

  • Gossen R2601 - page 28

    GOSSEN METRAWATT GMBH 28 4.2 Control parameters The control parameters are listed in the main parameter index group 1. 4.2.1 T able of the control parameters PI Parameter Display Format Unit Setting range Remarks 10h Proportional band Heat 16 bits 0.1 % 1 ... 9999 11h Proportional band Cool 16 bits 0.1 % 1 ... 9999 12h Deadband 16 bits (4.1.2) 0 .. ...

  • Gossen R2601 - page 29

    GOSSEN METRAWATT GMBH 29 4.3 Control instructions The control instructions in main group 2 of the parame ter index define the control action of the equipment 4.3.1 T able of the control instructions PI Parameter Format Unit Setting r ange Remarks Contents 20h Control status control channel 16 bits Bit field See 4.3.2 Controller type (= CnF1 , 2nd d ...

  • Gossen R2601 - page 30

    GOSSEN METRAWATT GMBH 30 4.3.2 Control status controll er channel (PI = 20h): Bit No. Value Meaning Re marks 2 - 0 000 001 010 011 Controller type = Limit monitor Positioner Two-state controller Heat / continuo us controller falling characteristic Two-state c ontroller C ool / continu ous controller rising characteristic 100 101 110 Three-state con ...

  • Gossen R2601 - page 31

    GOSSEN METRAWATT GMBH 31 4.3.3 Configuration of the 2nd signal input (PI = 22) Function signal input 2 Stand ard signal 2 Code B3 B4 B5 B4, B5 0 Fixed value controller (internal set point) 0 ... 20 mA 0 ... 10 V 1 Differential controller Fixed valu e controller Differential controller 2 – Slave controller 3 – 4 – Fixed value controller 4 ... ...

  • Gossen R2601 - page 32

    GOSSEN METRAWATT GMBH 32 4.4 Equipment specifications The equipment specifications in main gro up 3 of the parameter index among others in clude markin g identifi cation, software versi on and some configurations. 4.4.1 T able of equipment specifications PI Parameter Format Unit Setting range Remark s 30h Equipment marking 8 bits 26h Read only 31h ...

  • Gossen R2601 - page 33

    GOSSEN METRAWATT GMBH 33 4.4.2 Marking identifications (PI = 31h) Bit No. Valu e Meaning Remark 2 ... 0 001 100 101 111 A4 A1 A2 A3 5 ... 3 010 011 100 101 111 B2 B1 B5 B4 B3 Different from PI = 33h 6 0 7 0 1 Series version OEM version of hardware and software ...

  • Gossen R2601 - page 34

    GOSSEN METRAWATT GMBH 34 4.4.3 Configuration: Sensor unit, continuous output (PI = 32h) Code Sensor unit 1) 1) W hen switching-ove r , the physical quantity of the temp erature paramete r is preserved Continuous output Code Function Note Output range Output quantity 0Dh The current setting 2) is stored as a user defined default setting. 2) Configur ...

  • Gossen R2601 - page 35

    GOSSEN METRAWATT GMBH 35 4.4.4 Sensor type , B marking (PI = 33h) 1st character = sensor type: 2nd character = B marking: Code Sensor type 1) 1) A change influences th e presentatio n of the temper ature paramete rs Valu e Meaning Remarks Ty p e Kind Condition 0 B5 Read only , different from PI = 31h 0 J Thermocouple For signal input 1 at mar kin g ...

  • Gossen R2601 - page 36

    GOSSEN METRAWATT GMBH 36 4.4.5 Configuration of alarms 1 / 2 (PI = 36h) Bit No. Alarms 1 3 ... 0 Code 1) Start-up suppression Contact Heating circuit monitor 0 Relative Inac tive NOC Inactive 1 Absolute 2 Relative Activ e 3 Absolute 4 Relative Inac tive NCC 5 Absolute 6 Relative Activ e 7 Absolute 8 Relative Inac tive NOC Active 9 Absolute 0Ah Rela ...

  • Gossen R2601 - page 37

    GOSSEN METRAWATT GMBH 37 4.5 Heating current monitor Main group 6 of the parame ter index includes the parameters for heat ing current monitoring. 4.5.1 T able of the parameters fo r the heating current monitor 6 ... 4 Alarms 2 0 Relative Inac tive NOC 1 Absolute 2 Relative Activ e 3 Absolute 4 Relative Inac tive NCC 5 Absolute 6 Relative Activ e 7 ...

  • Gossen R2601 - page 38

    GOSSEN METRAWATT GMBH 38 5 Storage operations T o store all parameter and configuration da ta of an equipment, it is not required to address all data individually v ia paramete r indices. It is possibl e instead to directly read and/or write all data stored in the non-volati le data memor y (EEPROM) in one record. This function serves to save t he ...

  • Gossen R2601 - page 39

    GOSSEN METRAWATT GMBH 39 5.2 Send a record The long set for sending to the R2600/01 can prac tically only be generated from the rece ived long set at the request of a recor d. The function field (6th character) in 69h (write data) must be changed for that purpose. When copying to another R2600/01, the equipment address must b e adapted (5th charact ...

  • Gossen R2601 - page 40

    Edited in Germany • Subject to change without notice • A pdf version is available on the int ernet GOSSEN METRAWA TT GMBH Thomas-Mann-Str . 16-20 90471 Nürnberg, Germany Phone +49-(0)-911-8602-0 Fax +49-(0)-911-8602-669 E-Mail: info@gmc-inst ruments.com www .gmc-instruments.com ...

Fabricant Gossen Catégorie Network Card

Les documents que nous recevons du fabricant de l'appareilGossen R2601 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Gossen
- manuels d’utilisations R2601
- fiches produit Gossen
- dépliants
- ou étiquettes-énergie Gossen R2601
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Gossen R2601.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Gossen R2601, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Gossen R2601. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Gossen R2601.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Gossen R2601, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Gossen R2601 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Gossen R2601.

Le manuel d’utilisation complet Gossen, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Gossen R2601 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Gossen R2601, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lGossen R2601 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Gossen R2601 - qui devraient nous aider dans les premières étapes lors de l'utilisation Gossen R2601
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Gossen R2601
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Gossen R2601 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Gossen R2601?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Gossen R2601, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Gossen R2601 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)