-
Invacare 9000 SL - page 1
Service Manual DEALER: Keep this manual. The procedur es in this manual must be performed by a qualified technician only. For more information regarding Invacare products, parts, and services, please visit www.invacare.com 9000 Series 9000 SL 9000 XT 9000 XDT 9000XT Recliner ...
-
Invacare 9000 SL - page 2
REFERENCE DOCUMENTS 9000 Series 2 Part No. 107 6155 WARNING THE PROCEDURES IN THIS SERVICE MANUAL MUST BE PERFORMED BY A QUALIFIED TECHNICIAN. DO NOT SERVICE OR OPERATE THIS EQUIPMENT WITHOUT FIRST READING AND UNDERSTANDING (1) THE OWNER’S OPERATOR AND MAINTENANCE MANUAL AND (2) THE SERVICE MANUAL. IF YOU ARE UNABLE TO UNDERSTAND THE WARNINGS ...
-
Invacare 9000 SL - page 3
TABLE OF CONTENTS Part No. 1076155 3 9000 Series TABLE OF CONTENTS REFERENCE DOCUMENTS ................................................................. 2 SPECIAL NOTES ................................................................................ 6 LABEL LOCATION ............................................................................ 7 TYPI ...
-
Invacare 9000 SL - page 4
TABLE OF CONTENTS 9000 Series 4 Part No. 107 6155 TABLE OF CONTENTS 24-Inch Rear Wheels and 8-Inch Front Casters ..... ...................................................... ..........32 24-Inch Rear Wheels and 6-Inch Front Casters ..... ...................................................... ..........37 22-Inch Rear Wheels and 8-Inch Front Casters ...
-
Invacare 9000 SL - page 5
Part No. 1076155 5 9000 Series SECTION 8—ANTI-TIPPERS/WHEEL LOCKS ....................................... 80 Installing/Adjusting Anti-tippers ............ .................................................................... .............. ..............80 Installing Anti-Tippers ... ............................................................... ...
-
Invacare 9000 SL - page 6
SPECIAL NOTES 9000 Series 6 Part No. 107 6155 SPECIAL NOTES Signal words are use d in this manual and apply to hazards or unsafe practices which could result in personal injury or property damage. Refer to the following table for defi ...
-
Invacare 9000 SL - page 7
LABEL LOCATION Part No. 1076155 7 9000 Series IMPORT ANT NOTICE The wheel locks on this wheelchair have been pre-set at the factory to comply with the V eterans Administration functional Standard 8320.01 of the Federal Register , paragraph 3.2.4.5.3. If these wheel locks do not meet your needs, follow instructions below . ! CAUTION Any wheel lock a ...
-
Invacare 9000 SL - page 8
TYPICAL PRODUCT PARAMETERS 9000 Series 8 Part No. 107 6155 TYPICAL PRODUCT PARAMETERS *NOTE: These options are standard for this model. **NOTE: The seat ‐ to ‐ floor heights are based on urethane tir es. If wheelchair is equipped with pneumatic (properly ...
-
Invacare 9000 SL - page 9
TYPICAL PRODUCT PARAMETERS Part No. 1076155 9 9000 Series *NOTE: These options are standard for this model. **NOTE: The seat ‐ to ‐ floor heights are based on urethane tir es. If wheelchair is equipped with pneumatic (properly inflated) or solid ...
-
Invacare 9000 SL - page 10
TYPICAL PRODUCT PARAMETERS 9000 Series 10 Part No. 107 6155 *NOTE: These options are standard for this model. **NOTE: Th e seat ‐ to ‐ floor heights are based on pneumatic tir es and pneumatic tires with flat fr ee inserts. If wheelchair is e ...
-
Invacare 9000 SL - page 11
TYPICAL PRODUCT PARAMETERS Part No. 1076155 11 9000 Series *NOTE: These options are standard for this model. **NOTE: Th e seat ‐ to ‐ floor heights are based on pneumatic tir es and pneumatic tires with flat fr ee inserts. If wheelchair is eq ...
-
Invacare 9000 SL - page 12
SECTION 1—GENERAL GUIDELINES 9000 Series 12 Part No. 107 6155 SECTION 1—GENERAL GUIDELINES WARNING SECTION 1 - GENERAL GUIDELIN ES contai ns important inform ation for the safe operation and use of this product. DO NOT use this prod uct or any available optional equipment without first comple tely reading and understanding these instruction ...
-
Invacare 9000 SL - page 13
SECTION 1—GENERAL GUIDELINES Part No. 1076155 13 9000 Series Stability - Recliner Models Only AL W A YS make su re that the wheelchair is stable before using the recliner option. Ensure the spreader bar is attached and secured before us ing the 9000XT ...
-
Invacare 9000 SL - page 14
SECTION 1—GENERAL GUIDELINES 9000 Series 14 Part No. 107 6155 DO NOT attempt to lift the wheelchair by any remov able (detachable) parts. Lifting by means of any remov able (detachable) parts of the wheelchair may result in injury to th ...
-
Invacare 9000 SL - page 15
SECTION 2—SAFETY INSPECTION/TROUBLESHOOTING Part No. 1076155 15 9000 Series SECTION 2—SAFETY INSPECTION/TROUBLESHOOTING NOTE: Initial adjustments should be made to suit the end user ʹ s personal body structur e needs and pr eference. After init ial setup, p erform ...
-
Invacare 9000 SL - page 16
SECTION 2—SAFETY INSPECTION/TROUBLESHOOTING 9000 Series 16 Part No. 107 6155 ❑ Ensure wheel bearings are clean and free of moisture. ❑ Check headtube locknuts for tightness. ❑ Inspect casters for cracks and wear . ❑ Inspect front casters for cracked, b ...
-
Invacare 9000 SL - page 17
SECTION 2—SAFETY INSPECTION/TROUBLESHOOTING Part No. 1076155 17 9000 Series 2. 9000 SL/9000 XT only ‐ Keep quick ‐ release axles free of dirt and lint to ensure positive locking and proper operation. Refer to Adjusting Quick ‐ Release Axle on ...
-
Invacare 9000 SL - page 18
SECTION 3—SEAT AND BACK 9000 Series 18 Part No. 107 6155 SECTION 3—SEAT AND BACK WARNING After any adjustments, repair or service and before use, make sure all attachi ng hardware is tightened securely. Otherw ise, injury or damage may occur. The seat depth, back height/an gle, seat angle, size/posit ion of the front casters, size/position ...
-
Invacare 9000 SL - page 19
SECTION 3—SEAT AND BACK Part No. 1076155 19 9000 Series Adjusting Back Height 9000 SL without Adjustable Back Angle Option NOTE: For this proced ure, re fe r to FIGURE 3.2. NOTE: There ar e two (2) height ranges of back canes with thr ee (3) height settings wi ...
-
Invacare 9000 SL - page 20
SECTION 3—SEAT AND BACK 9000 Series 20 Part No. 107 6155 9000 SL with Adjustable Back Angle Option and 9000 XT/XDT NOTE: For this proced ure, re fe r to FIGURE 3.3. 1. Remove the two (2) mounting screws, spacers and locknuts that secure the two (2) back canes ...
-
Invacare 9000 SL - page 21
SECTION 3—SEAT AND BACK Part No. 1076155 21 9000 Series 2. Remove the four (4) button screws and locknuts that secure th e tw o (2) piv ot links to the wheelchair frame and crossbraces. 3. Remove the two (2) button screws, locknuts and ...
-
Invacare 9000 SL - page 22
SECTION 3—SEAT AND BACK 9000 Series 22 Part No. 107 6155 FIGURE 3.4 Adjusting Seat Width Wheelchair Frame Button Screw (STEPS 2,7) Crossbrace (STEPS 4,5) Pivot Link (STEPS 2,7) Locknut (STEPS 2,7) Button Screw (STEPS 2,7) Locknut (STEPS 2,7) Crossbrace Saddle (STEPS 3,8) Button Screw (STEPS 3,8) Locknut (STEPS 3,8) Button Screw (STEPS 2,7) Locknu ...
-
Invacare 9000 SL - page 23
SECTION 3—SEAT AND BACK Part No. 1076155 23 9000 Series Adjusting Seat Depth WARNING The seat depth, back height/an gle, seat angle, size/posit ion of the front casters, size/position of the rear wh eels, anti-tipper model, as well as the us er condition directly relate to the stability of the whee lchair. Any change to one (1) or any com- bi ...
-
Invacare 9000 SL - page 24
SECTION 3—SEAT AND BACK 9000 Series 24 Part No. 107 6155 9000 XDT and 9000 SL NOTE: For this proced ure, re fe r to FIGURE 3.6. NOTE: 9000 XDT wheelchairs have two (2) frame depth ranges: 16 to 18 inches and 19 to 20 inches. A 16 ‐ 18 ‐ ...
-
Invacare 9000 SL - page 25
SECTION 3—SEAT AND BACK Part No. 1076155 25 9000 Series 6. Install the new seat upholstery onto the wheelchair . Make sure to line up the mounting holes in the seat extension tubes with the new seat upholstery . Refer to Replacing S ...
-
Invacare 9000 SL - page 26
SECTION 4—FRONT CASTERS 9000 Series 26 Part No. 107 6155 SECTION 4—FRONT CASTERS WARNING After any adjustments, repair or service and before use, make sure all attachi ng hardware is tightened securely. Otherw ise, injury or damage may occur. Front Caster Mount ing Adju stments NOTE: For this proced ure, re fe r to F ...
-
Invacare 9000 SL - page 27
SECTION 4—FRONT CASTERS Part No. 1076155 27 9000 Series Converting from Trailing to Leading or Leading to Trailing Casters NOTE: For this proced ure, re fe r to FIGURE 4.2. Adjusting the caster headtube position (leading or trailing) changes the wh eelbase length of t ...
-
Invacare 9000 SL - page 28
SECTION 4—FRONT CASTERS 9000 Series 28 Part No. 107 6155 5. Loosely tighten the bottom of the existing caster headtube to the wheelchair frame using existing hardware. 6. Adjust the seat ‐ to ‐ floor angle. Refer to Changing Seat ‐ to ‐ Floor Heigh ...
-
Invacare 9000 SL - page 29
SECTION 5—SEAT TO FLOOR Part No. 1076155 29 9000 Series SECTION 5—SEAT TO FLOOR WARNING After any adjustments, repair or service and before use, make sure all attachi ng hardware is tightened securely. Otherw ise, injury or damage may occur. Changing Seat-to-Floor Height/Seat-to-Floor Angle WARNING Before performing this procedur e, ref ...
-
Invacare 9000 SL - page 30
SECTION 5—SEAT TO FLOOR 9000 Series 30 Part No. 107 6155 FIGURE 5.1 Changing Seat-to-Floor Hei ght/Seat-to-Floor Angle 2. Refer to the following charts of rear wheel sizes and front caster sizes to determine mounting adjustments for obtainable seat ‐ to ‐ floor he ...
-
Invacare 9000 SL - page 31
SECTION 5—SEAT TO FLOOR Part No. 1076155 31 9000 Series 8. Adjust the wheel locks. Refer to Usin g/Adjusting the Pa t i e n t Operated Whee l Locks in the Owner ’ s Manual, part number 1056953. WARNING After changing seat-to-floor height and/or seat-to-floor angle, the ...
-
Invacare 9000 SL - page 32
SECTION 5—SEAT TO FLOOR 9000 Series 32 Part No. 107 6155 FIGURE 5.3 Adult/Tall Frame Style Adult/Hemi Frame Styles Refer to the charts on the following pages for obtainable seat ‐ to ‐ floor heights and seat ‐ to ‐ floor angles for wheelchairs with the adult/hemi ...
-
Invacare 9000 SL - page 33
SECTION 5—SEAT TO FLOOR Part No. 1076155 33 9000 Series NOTE: Charts 1 to 8 apply to adult/hemi frame styles only . Refer to the charts for seat ‐ to ‐ floor height settings for adult/tall (Adult/T all Frame Style on page 31) and super ...
-
Invacare 9000 SL - page 34
SECTION 5—SEAT TO FLOOR 9000 Series 34 Part No. 107 6155 *NOTE: This offset axle plate position re qu i res the caster headtube to be leading to pr ovide adequate tire clearance between the rea r tire and the front caster . Refer to Con ...
-
Invacare 9000 SL - page 35
SECTION 5—SEAT TO FLOOR Part No. 1076155 35 9000 Series *NOTE: This offset axle plate position re qu i res the caster headtube to be leading to pr ovide adequate tire clearance between the rea r tire and the front caster . Refer to Conv ...
-
Invacare 9000 SL - page 36
SECTION 5—SEAT TO FLOOR 9000 Series 36 Part No. 107 6155 *NOTE: This offset axle plate position re qu i res the caster headtube to be leading to pr ovide adequate tire clearance between the rea r tire and the front caster . Refer to Con ...
-
Invacare 9000 SL - page 37
SECTION 5—SEAT TO FLOOR Part No. 1076155 37 9000 Series 24-Inch Rear Wheels an d 6-Inch Front Casters WARNING If changing the seat-to -floor angle to 6°, anti-tippers MUST be installed. Refer to the following table to determine the obtainable seat ‐ to ‐ floor heights and seat ‐ to ‐ fl ...
-
Invacare 9000 SL - page 38
SECTION 5—SEAT TO FLOOR 9000 Series 38 Part No. 107 6155 Chart 10 - Seat-to-Floor Height of 17½ inches and 3° Angle REAR WHEEL POSITION ANTI-TIP PART/MODEL NUMBERS FRONT CASTER OFFSET AXLE OPTION STANDARD MOUNTING POSITION ADJC CAM POSITION FORWARD REARWARD N/A On-Chair 1058752 Off-Chair Chart 11 - Seat-to-Floor Height of 17½ inches and 6° An ...
-
Invacare 9000 SL - page 39
SECTION 5—SEAT TO FLOOR Part No. 1076155 39 9000 Series 22-Inch Rear Wheels an d 8-Inch Front Casters WARNING If changing the seat-to -floor angle to 6°, anti-tippers MUST be installed. Chart 13 - Seat-to-Floor Height of 16½ inches and 3° Angle REAR WHEEL POSITION ANTI-TIP PART/MODEL NUMBERS FRONT CASTER OFFSET AXLE OPTION STANDARD MOUNTIN ...
-
Invacare 9000 SL - page 40
SECTION 5—SEAT TO FLOOR 9000 Series 40 Part No. 107 6155 Refer to the following table to determine the obtainable seat ‐ to ‐ floor heights and seat ‐ to ‐ floor angles for 22 ‐ inch rear wheels and 8 ‐ inch front casters: *NOTE: The seat ‐ t ...
-
Invacare 9000 SL - page 41
SECTION 5—SEAT TO FLOOR Part No. 1076155 41 9000 Series *NOTE: This offset axle plate position re qu i res the caster headtube to be leading to pr ovide adequate tire clearance between the rea r tire and the front caster . Refer to Conv ...
-
Invacare 9000 SL - page 42
SECTION 5—SEAT TO FLOOR 9000 Series 42 Part No. 107 6155 *NOTE: This offset axle plate position re qu i res the caster headtube to be leading to pr ovide adequate tire clearance between the rea r tire and the front caster . Refer to Con ...
-
Invacare 9000 SL - page 43
SECTION 5—SEAT TO FLOOR Part No. 1076155 43 9000 Series *NOTE: This offset axle plate position re qu i res the caster headtube to be leading to pr ovide adequate tire clearance between the rea r tire and the front caster . Refer to Conv ...
-
Invacare 9000 SL - page 44
SECTION 5—SEAT TO FLOOR 9000 Series 44 Part No. 107 6155 Chart 21 - Seat-to-Floor Height of 17½ inches and 0° Angle REAR WHEEL POSITION ANTI-TIP PART/MODEL NUMBERS FRONT CASTER OFFSET AXLE OPTION STANDARD MOUNTING POSITION ADJC CAM POSITION FORWARD REARWARD N/A On-Chair 1058836 Off-Chair Chart 22 - Seat-to-Floor Height of 17½ in ches and 3° A ...
-
Invacare 9000 SL - page 45
SECTION 5—SEAT TO FLOOR Part No. 1076155 45 9000 Series Chart 24 - Seat-to-Floor Height of 16½ inches and 0° Angle REAR WHEEL POSITION ANTI-TIP PART/MODEL NUMBERS FRONT CASTER OFFSET AXLE OPTION STANDARD MOUNTING POSITION ADJC CAM POSITION FORWARD REARWARD N/A for this frame style N/A On-Chair 1058836 Off-Chair Chart 25 - Seat-to-Floor Height o ...
-
Invacare 9000 SL - page 46
SECTION 5—SEAT TO FLOOR 9000 Series 46 Part No. 107 6155 20-Inch Rear Wheels an d 8-Inch Front Casters WARNING If changing the seat-to -floor angle to 6°, anti-tippers MUST be installed. Refer to the following table to determine the obtainable seat ‐ to ‐ floor heights and seat ‐ to ‐ f ...
-
Invacare 9000 SL - page 47
SECTION 5—SEAT TO FLOOR Part No. 1076155 47 9000 Series *NOTE: The seat ‐ to ‐ floor heights ar e based on ur ethane tires. If wh eelchair is equipped with pneumatic (properly inflated) or solid rubber tir es, add ¼ inc h to the measureme ...
-
Invacare 9000 SL - page 48
SECTION 5—SEAT TO FLOOR 9000 Series 48 Part No. 107 6155 20-Inch Rear Wheels an d 6-Inch Front Casters WARNING If changing the seat-to -floor angle to 6°, anti-tippers MUST be installed. Refer to the following table to determine the obtainable seat ‐ to ‐ floor heights and seat ‐ to ‐ f ...
-
Invacare 9000 SL - page 49
SECTION 5—SEAT TO FLOOR Part No. 1076155 49 9000 Series Chart 32 - Seat-to-Floor Height of 17½ inches and 3° Angle REAR WHEEL POSITION ANTI-TIP PART/MODEL NUMBERS FRONT CASTER OFFSET AXLE OPTION STANDARD MOUNTING POSITION ADJC CAM POSITION FORWARD REARWARD 1360A On-Chair 1058752 Off-Chair Chart 33 - Seat-to-Floor Height of 17½ in ches and 6° ...
-
Invacare 9000 SL - page 50
SECTION 5—SEAT TO FLOOR 9000 Series 50 Part No. 107 6155 Chart 35 - Sea t-to-Fl oor Height of 16½ inches and 3° An gle REAR WHEEL POSITION ANTI-TIP PART/MODEL NUMBERS FRONT CASTER OFFSET AXLE OPTION STANDARD MOUNTING POSITION ADJC CAM POSITION FORWARD REARWARD N/A for this frame style N/A On-Chair 1058752 Off-Chair Chart 36 - Seat-to-Floor Heig ...
-
Invacare 9000 SL - page 51
SECTION 5—SEAT TO FLOOR Part No. 1076155 51 9000 Series Chart 38 - Seat-to-Floor Height of 15½ in ches and 3° An gle REAR WHEEL POSITION ANTI-TIP PART/MODEL NUMBERS FRONT CASTER OFFSET AXLE OPTION STANDARD MOUNTING POSITION ADJC CAM POSITION FORWARD REARWARD 1360A On-Chair 1058752 Off-Chair Chart 39 - Seat-to-Floor Height of 15½ in ches and 6? ...
-
Invacare 9000 SL - page 52
SECTION 6—REAR WHEELS 9000 Series 52 Part No. 107 6155 SECTION 6—REAR WHEELS WARNING After any adjustments, repair or service and before use, make sure all attachi ng hardware is tightened securely. Otherw ise, injury or damage may occur. NOTE: Except wher e noted, the procedur es in this section apply ? ...
-
Invacare 9000 SL - page 53
SECTION 6—REAR WHEELS Part No. 1076155 53 9000 Series 5. If the detent balls are not protruding past the inside of the axle bushing or there is too much side ‐ to ‐ side movement of the rear wheel assembly , refer to the Owner ? ...
-
Invacare 9000 SL - page 54
SECTION 6—REAR WHEELS 9000 Series 54 Part No. 107 6155 FIGURE 6.2 Removing/Installing Rear Wheels - Perma nent Axles - Models without Offset Axle Opti on NOTE: Make sure axle spacer is between re a r wheel an d wheelchair frame if wheelchair is equipped with conventional arms ...
-
Invacare 9000 SL - page 55
SECTION 6—REAR WHEELS Part No. 1076155 55 9000 Series iii. P osition one (1) offset axle plate on the outside of the wheelchair frame in the appropriate position determined in STEP i. iv . P osition the second offset axle plate in the s ...
-
Invacare 9000 SL - page 56
SECTION 6—REAR WHEELS 9000 Series 56 Part No. 107 6155 FIGURE 6.3 Removing/Installing Rear Wheels - Perman ent Axles - Models with Offset Axle Option DETAIL “A ” - OFFSET AXLE PLAT E MOUNTING PO SITIONS NOTE: The offset axle plates are numbered on one (1) side only . Plates may need ...
-
Invacare 9000 SL - page 57
SECTION 6—REAR WHEELS Part No. 1076155 57 9000 Series Adjusting Quick-Release Axle WARNING NEVER use quick-release axle s on the 9000 XT (models with offset axle option only), 9000XDT or 9000XT recliner wheelchairs. NOTE: For this proced ure, re fe r to FIGURE 6.4. 1. Remove rear wheel and quick ‐ rel ...
-
Invacare 9000 SL - page 58
SECTION 7—RECLINER 9000 Series 58 Part No. 107 6155 SECTION 7—RECLINER WARNING After any adjustments, repair or service and before use, make sure all attachi ng hardware is tightened securely. Otherw ise, injury or damage may occur. ALWAYS make sure that the whee lchair is stable before using the recliner option. Ensure the spreader bar is ...
-
Invacare 9000 SL - page 59
SECTION 7—RECLINER Part No. 1076155 59 9000 Series NOTE: Tu r n i n g the swivel nut counter clockwise will pull the barr el end of the cable assembly downward creating te nsion on the re le a s e handle. 9. Rotate the jam nut counterclockw ise ...
-
Invacare 9000 SL - page 60
SECTION 7—RECLINER 9000 Series 60 Part No. 107 6155 •I f there is too much play in the release handle: i. Rotate the jam nut clockwise (downw ard) tw o (2) to three (3) rev olutions. ii. Rotate the swivel nut counterclockwise (upw ard) on ...
-
Invacare 9000 SL - page 61
SECTION 7—RECLINER Part No. 1076155 61 9000 Series 4. Loosen the jam nut, rotate clock wise (downw ard) and run the jam nut to the bottom of the threads. 5. Hold swiv el nut in place and unthread cable assembly from swive l nut. To ...
-
Invacare 9000 SL - page 62
SECTION 7—RECLINER 9000 Series 62 Part No. 107 6155 2. Align threads of threaded sector with exposed threads of locking rod through cutout in recliner tube. CAUTION DO NOT route the cable assembly to the ou tside of the locking rod/recliner tube assembly as it may rub against the tires. ...
-
Invacare 9000 SL - page 63
SECTION 7—RECLINER Part No. 1076155 63 9000 Series FIGURE 7.4 Disconnecting/Connectin g Lower Cable Assembly DETAIL “A” - TOP VIEW Locking Rod Housing Locking Rod Incorrect Assemb ly Housing Correct Assembly Locking Rod/Recliner Tube Assembly Locknuts (STEP 6) Support Housing and Cable Assembly (STEP 6) Threaded Sector Threads (STEPS 1,2) Thr ...
-
Invacare 9000 SL - page 64
SECTION 7—RECLINER 9000 Series 64 Part No. 107 6155 Replacing Threaded Sector NOTE: For this proced ure, re fe r to FIGURE 7.5. 1. Disconnect the lower cable assembly . Refer to Disconnecting/Connecting Lower Cable Assembly on page 61. 2. Remove the release handle ...
-
Invacare 9000 SL - page 65
SECTION 7—RECLINER Part No. 1076155 65 9000 Series Replacing Locking Rod NOTE: For this proced ure, re fe r to FIGURE 7.6. 1. Remove the mounting screw and locknut that secure the lockin g rod to the bac k tu be mounting bracket. 2. Pull locking rod/re ...
-
Invacare 9000 SL - page 66
SECTION 7—RECLINER 9000 Series 66 Part No. 107 6155 2. Remove the armrests. Refer to Removing/Installing the Armrest in the ow ner ʹ s manual, part number 1056953. 3. If applicable, remove the headrest. Refer to Replacing the Headrest/Back Upholstery ...
-
Invacare 9000 SL - page 67
SECTION 7—RECLINER Part No. 1076155 67 9000 Series FIGURE 7.7 Replacing Back Tube Removing/Installing Spring Lift Mechanism NOTE: For this proced ure, re fe r to FIGURE 7.8. Removing 1. Recline the wheelchair exposing the two (2) holes on either side of the spring lif ...
-
Invacare 9000 SL - page 68
SECTION 7—RECLINER 9000 Series 68 Part No. 107 6155 Installing CAUTION DO NOT remove the retaining clip before the sprin g lift mech anism is secured to the wheelchair. If the retaining clip is removed, th e spring lift mechanism will compress. This will make the sp ring lift mechanism unusable. NOTE: If installing a new sprin ...
-
Invacare 9000 SL - page 69
SECTION 7—RECLINER Part No. 1076155 69 9000 Series Replacing Recliner Tube NOTE: For this proced ure, re fe r to FIGURE 7.9. 1. Remove the mounting screw and locknut that secure the lockin g rod to the bac k tu be mounting bracket. 2. Slide anti ‐ ra ...
-
Invacare 9000 SL - page 70
SECTION 7—RECLINER 9000 Series 70 Part No. 107 6155 FIGURE 7.9 Replacing Recliner Tube STEPS 3 and 10 Bolt and Locknut Locknut (STEPS 1,12) Locking Ro d (STEPS 1,2,5, 9,12) Anti-Rattle (STEPS 2,11) Lower Cable Assembly (STEPS 4,13) Recliner Tube (STEPS 5,7,8,9,11 ) Locknut (STEPS 7,8) Mounting Screw (STEPS 1,12) Back Tube Mounting Bracket (STEPS ...
-
Invacare 9000 SL - page 71
SECTION 7—RECLINER Part No. 1076155 71 9000 Series Adjusting Seat Width NOTE: For this proced ure, re fe r to FIGURE 7.10 on page 73. NOTE: When adjusting the seat width of the wheelchair , the back and seat upholstery , and spreader bar MUST b ...
-
Invacare 9000 SL - page 72
SECTION 7—RECLINER 9000 Series 72 Part No. 107 6155 10. Secure the pivot link to the crossbraces and wheelchair frame with the four (4) button screws and locknuts. Securely tighten. 11. Reinstall the two (2) button screws, locknuts and cros ...
-
Invacare 9000 SL - page 73
SECTION 7—RECLINER Part No. 1076155 73 9000 Series FIGURE 7.10 Adjusting Seat Width Pivot Link (STEPS 5, 10) Locknut (STEPS 5,10) Crossbrace (STEPS 8,10) Button Screw (STEPS 5,10) Wheelchair Frame Locknut (STEPS 5,10) Button Screw (STEPS 6,11) Crossbrace Saddle (STEPS 6,11) Button Screw s (STEPS 5,10) Locknut (STEPS 6,11) Crossbrace Saddle (STEPS ...
-
Invacare 9000 SL - page 74
SECTION 7—RECLINER 9000 Series 74 Part No. 107 6155 Adjusting Seat Depth NOTE: For this proced ure, re fe r to FIGURE 7.1 1. 1. Remove the existing seat upholstery from the crossbraces. Refer to Replacing the Seat Upholstery in the Owner ’ s Manual, ...
-
Invacare 9000 SL - page 75
SECTION 7—RECLINER Part No. 1076155 75 9000 Series Removing/Installing Rear Wheels With Patient Operated Wheel Locks NOTE: For this proced ure, re fe r to FIGURE 7.12. 1. Remove the axle mounting screw and locknut that secure the patient operated wheel lock, spacers, ...
-
Invacare 9000 SL - page 76
SECTION 7—RECLINER 9000 Series 76 Part No. 107 6155 NOTE: For this proced ure, re fe r to FIGURE 7.14. 1. P erform one (1) of the following: • Engage ‐ Apply pressure downw ard on wh eel lock handle. • Disengage ‐ Lift up on wheel lock hand ...
-
Invacare 9000 SL - page 77
SECTION 7—RECLINER Part No. 1076155 77 9000 Series FIGURE 7.15 Adjusting Attendant Operated Wheel Locks Changing Seat-to-Floor Height NOTE: For this proced ure, re fe r to FIGURE 7.16. 1. Remove the rear wheels. Refer to Removing/Installing Rear Wheels on page 75. 2. If necessary ...
-
Invacare 9000 SL - page 78
SECTION 7—RECLINER 9000 Series 78 Part No. 107 6155 FIGURE 7.16 Changing Seat-to-Floor Height Installing Anti-Tippers NOTE: For this proced ure, re fe r to FIGURE 7.17. 1. Install the anti ‐ rattles onto the rear frame tubes if not already in place. 2. P osition the ...
-
Invacare 9000 SL - page 79
SECTION 7—RECLINER Part No. 1076155 79 9000 Series 9000 XT RECLINER WHEEL SIZE REAR/CASTER SEAT-TO-FLOOR HEIGHT ANTI-TIPPER LENGTH, HEIGHT ON CHAIR OFF CHAIR KIT NUMBER 24/8-inch 19½ 11½, 2½-inches 1021767 1021767 22/8-inch 18½ 10¼, 1-7/8-inches 1061110 1061110 20/8-inch 17½ 10, 1½-inches 1061109 1061109 ...
-
Invacare 9000 SL - page 80
SECTION 8—ANTI-TIPPERS/WHEEL LOCKS 9000 Series 80 Part No. 107 6155 SECTION 8—ANTI-TIPPERS/WHEEL LOCKS WARNING After any adjustments, repair or service and before use, make sure all attachi ng hardware is tightened securely. Othe rwise injury or damage may occur. NOTE: The procedur es in this section apply to ...
-
Invacare 9000 SL - page 81
SECTION 8—ANTI-TIPPERS/WHEEL LOCKS Part No. 1076155 81 9000 Series 3. Measure the distance between the bottom of the anti ‐ tipper wheels and the ground/floor . NOTE: A 1½ to 2 ‐ inch clearance between the bottom of the anti ‐ tipper wheels ...
-
Invacare 9000 SL - page 82
SECTION 8—ANTI-TIPPERS/WHEEL LOCKS 9000 Series 82 Part No. 107 6155 Using/Adjusting Disk Wheel Locks Using Patient Operated Disk Wheel Locks WARNING DO NOT attempt to stop a moving wheelcha ir with wheel lock s. Wheel locks are not brakes. NOTE: For this proced ure, re fe r to FIGURE 8.3. NOTE: Position wheelch ...
-
Invacare 9000 SL - page 83
SECTION 8—ANTI-TIPPERS/WHEEL LOCKS Part No. 1076155 83 9000 Series 2. Depending on the model of wheel lo ck installed on the wheelchair , perform one (1) of the following: •P u s h ‐ to ‐ Lock ‐ To engage, push the wheel lock handle forw ard. ...
-
Invacare 9000 SL - page 84
SECTION 8—ANTI-TIPPERS/WHEEL LOCKS 9000 Series 84 Part No. 107 6155 7. Repeat STEPS 1 ‐ 6 until the wheel lock shoe embeds the tire 1/8 ‐ inch (3 /16 ‐ inch for pneumatic tires) and holds the occupied wheelchair in place when pushed. 8. If th ...
-
Invacare 9000 SL - page 85
SECTION 8—ANTI-TIPPERS/WHEEL LOCKS Part No. 1076155 85 9000 Series Installing Wheel Lock Shoe Extensions NOTE: For this proced ure, re fe r to FIGURE 8.5. 1. Loosen the tw o (2) set screws on the wheel lock shoe extension until the set screws do not pr ...
-
Invacare 9000 SL - page 86
SECTION 8—ANTI-TIPPERS/WHEEL LOCKS 9000 Series 86 Part No. 107 6155 NOTES ...
-
Invacare 9000 SL - page 87
LIMITED WARRANTY Part No. 1076155 87 9000 Series LIMITED WARRANTY PLEASE NOTE: THE WARRANTY BELOW HAS BEEN DRAFTED TO COMPLY WITH FEDERAL LAW APPLICABL E TO PRODUCTS MANUFACTURED AFTER JULY 4, 1975. This warranty is extended only to the original purchaser/user of our products. This warranty gives you specif ic legal rights and you may also have oth ...
-
Invacare 9000 SL - page 88
Invacare Corporation www.invacare.com USA One Invacare Way Elyria, Ohio USA 44036-2125 800-333-6900 Canada 570 Matheson Blvd E Unit 8 Mississauga Ontario L4Z 4G4 Canada 800-668-5324 Invacare, the Meda llion Design, and Yes, you can. are register ed trademarks of Invacare Corporation. 3-in-1 is a registered trademark of the WD-40 Company. Teflon is ...
Avez-vous une question à propos de Invacare 9000 SL?
Utiliser le formulaire ci-dessous
Si vous n’avez pas résolu votre problème avec Invacare 9000 SL, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Invacare 9000 SL il est probable qu’il a envie de partager la façon de le résoudre.