Français dropdown-ico

Manuel d’utilisation Shure 27B8614

22 pages 0.72 mb
Télécharger

Aller à la page of 22

Summary
  • Shure 27B8614 - page 1

    UC Wireless System User Guide 27B8614 (AA)  2001, Shure Incorporated Printed in U.S.A. UC WIRELESS SYSTEM User Guide ...

  • Shure 27B8614 - page 2

    – 1 – T ABLE OF CONTENTS QUICK SETUP GUIDE FOR THE SHURE UC WIRELESS SYSTEM 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . UC4 Receiver Setup 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . UC1/UC2 T ransmitter Setup 2 . . ...

  • Shure 27B8614 - page 3

    ENGLISH ENGLISH – 2 – QUICK SETUP GUIDE FOR THE SHURE UC WIRELESS SYSTEM UC4 Receiver Setup 1. Plug the dc power supply into the power connector on the back of the receiver . Connect the other end of the power supply into an electrical outlet. 2. Attach the two antennas to the ANTENNA IN BNC connectors. 3. Connect audio cable(s) from the UC4 au ...

  • Shure 27B8614 - page 4

    – 3 – UC1 UC2 UC4 UC WIRELESS SYSTEM COMPONENTS FIGURE 1 SYSTEM DESCRIPTION The Shure UC Wireless System is a frequency–agile, diversity wireless system operating in the UHF band. Both th e receiver and the transmitter are microprocessor controlled by Phase Locked Loop (PLL) circuitry for a clear , steady signal. The receiver is half–rack s ...

  • Shure 27B8614 - page 5

    ENGLISH ENGLISH – 4 – 1 23 4 6 7 8 9 10 11 12 5 1 23 4 UC1 BODY P ACK TRANSMITTER FEA TURES AND CONTROLS FIGURE 2 UC1 TRANSMITTER FEA TURES AND CONTROLS 1. Antenna. A flexible 1/4 wave whip antenna is permanently attached to the top of the UC1 Body–Pack transmitter . 2. Power/Battery Fuel Gauge. When the Power switch is in the ON position, on ...

  • Shure 27B8614 - page 6

    – 5 – 1 5 3 7 4 8 6 2 UC2 HAND–HELD TRANSMITTER FEA TURES AND CONTROLS FIGURE 3 UC2 TRANSMITTER FEA TURES AND CONTROLS 1. Grille. Protects the microphone cartridge and helps reduce breath sounds and wind noise. The grilles for the vari- ous microphone heads differ in appearance. 2. Power Indicator/Battery Fuel Gauge. When the UC2 is turned on ...

  • Shure 27B8614 - page 7

    ENGLISH ENGLISH – 6 – A B 1 2 34 5 6 7 8 9 10 1 1 12 13 14 15 16 17 17 UC4 RECEIVER CONTROLS AND INDICA TORS FIGURE 4 UC4 RECEIVER CONTROLS AND CONNECTORS 1. A/B Diversity Signal Indicators . Indicate presence of received RF signal and diversity status. 2. Squelch Control. Sets the point at which the receiver “mutes” when the transmitter si ...

  • Shure 27B8614 - page 8

    – 7 – RECEIVER CABLE CONNECTIONS 1. Connect the receiver output to the mixer or amplifier input, using a standard audio cable with a female 3–pin XLR connector or 1/4” phone plug. Refer to Figure 5. 2. Connect the AC power adapter to the POWER jack on the rear panel of the receiver . 3. Plug the AC adapter into an AC power source. Power Sup ...

  • Shure 27B8614 - page 9

    ENGLISH ENGLISH – 8 – Changing the UC1 T ransmitter Battery 1. Make sure the transmitter power ON/OFF switch is in the OFF position. 2. Open the transmitter battery compartment by squeezing the two tabs on either side of the transmitter . Then flip the battery cover down. Refer to Figure 6. 3. Lift up on the edge of the battery remove it. 4. In ...

  • Shure 27B8614 - page 10

    – 9 – OPERA TING THE UC1 BODY–P ACK SYSTEM 1. Clip the UC1 body–pack transmitter to your belt, waistband, or guitar strap. 2. Connect the lavalier microphone, headset microphone, WM98 microphone, or instrument adapter cable to the UC1 transmitter , as shown in Figure 8. MICROPHONE CABLE OR INSTRUMENT ADAPTER CABLE CONNECTING A MICROPHONE OR ...

  • Shure 27B8614 - page 11

    ENGLISH ENGLISH – 10 – OPERA TING THE UC2 HAND-HELD SYSTEM 1. Slide the transmitter power ON/OFF switch to the ON position. One of the three transmitter LEDs will glow . If none of the LEDs glow , change the battery . 2. T urn the receiver on by pushing the ON button. The receiver LED display and RF LEDs will glow . 3. Make s ure t he t ransmit ...

  • Shure 27B8614 - page 12

    – 1 1 – Changing the T ransmitter Group/Channel Settings 1. Turn the transmitter off and open the battery compartment to expose the GROUP and CHANNEL switches. Refer to Figure12 below . 2. Using the supplied screwdriver , rotate the GROUP switch until the desired setting is reached. Then rotate the CHANNEL switch until the the desired setting i ...

  • Shure 27B8614 - page 13

    ENGLISH ENGLISH – 12 – CHANGING RECEIVER SETTINGS The receiver display identifies the operating frequency by Group and Channel. The character on the left represents the Group setting and the character on the right represents the Channel setting. Groups are preconfigured sets of frequencies or channels that work well together . A complete list o ...

  • Shure 27B8614 - page 14

    – 13 – Adjusting the Equalizer Setting The UC4 receiver incorporates a two band equalizer to help adjust the sound of the wireless system to match that of other wired and wireless products in an installation. See Figure 17. ADJUSTING THE UC4 RECEIVER EQUALIZER SETTING FIGURE 17 Adjusting the Low–Cut Filter (High Pass) The low–cut (or high? ...

  • Shure 27B8614 - page 15

    ENGLISH ENGLISH – 14 – RECEIVER MOUNTING T able Mounting T o mount a receiver on a table or other horizontal surface, attach the four adhesive bumpers to the bottom corners of the receiver and place the receiver on the mounting surface. See Figure 20. RUBBER FEET R T ABLE MOUNTING THE UC4 RECEIVER FIGURE 20 Rack Mounting a Single Receiver T o m ...

  • Shure 27B8614 - page 16

    – 15 – Rack Mounting T wo Receivers Side by Side T o mount two receivers side by side in an equipment rack, select the double rack–mounting kit supplied with the system and proceed as follows: 1. Remove the two screws on the outer side of each receiver . 2. Position the small mounting brackets over the holes on the outer side of each receiver ...

  • Shure 27B8614 - page 17

    ENGLISH ENGLISH – 16 – RECEIVER ANTENNA INST ALLA TION Rear Mounted Antenna Installation Attach the supplied UHF antennas to the BNC connectors on the receiver back panel, as shown in Figure 23. For best performance, point the antenna tips away from each other at a 90 ° angle (45 ° from vertical axis). NOTE: For improved RF performance (3 dB ...

  • Shure 27B8614 - page 18

    – 17 – 3. Attach the supplied UHF antennas to the BNC connectors on the front panel as shown in Figure 26. For best perfor- mance, orient the antennas with tips pointing away from each other at a 45 ° angle from vertical. A TT ACHING FRONT MOUNT ANTENNAS TO BNC CONNECT ORS FIGURE 26 Remote Antenna Installation NOTE: The UA500 Remote Mount Ante ...

  • Shure 27B8614 - page 19

    ENGLISH ENGLISH – 18 – LOGIC CONNECTION SPECIFICA TIONS The logic capability of the UC4 receiver provides two functions: transmitter status indication (which can be used to signal and control other events) and transmitter low battery indication. The various logic functions and their applica- tions are presented in the following table. Refer to ...

  • Shure 27B8614 - page 20

    – 19 – TIPS FOR ACHIEVING OPTIMUM PERFORMANCE • Maintain a line of sight between the transmitter and receiver antennas. • Avoid placing transmitter and receiver where metal or other dense materials may be present. • Avoid placing the receiver near computers or other RF generating equipment. • Avoid placing the receiver in the bottom of ...

  • Shure 27B8614 - page 21

    ENGLISH ENGLISH – 20 – SPECIFICA TIONS For product specifications, refer to the supplement that came with your system. LICENSING INFORMA TION Changes or modifications not expressly approved by Shure Incorporated could void your authority to operate the equipment. Licensing of Shure wireless microphone equipment is the user ’s responsibility , ...

  • Shure 27B8614 - page 22

    SHURE Incorporated Web Address: http://www .shure.com 222 Hartrey Avenue, Evanston, IL 60202–3696, U.S.A. Phone: 847-866–2200 Fax: 847-866-2279 In Europe, Phone: 49-7131-72140 Fax: 49-7131-721414 In Asia, Phone: 852-2893-4290 Fax: 852-2893-4055 Elsewhere, Phone: 847-866–2200 Fax: 847-866-2585 ...

Fabricant Shure Catégorie Stereo System

Les documents que nous recevons du fabricant de l'appareilShure 27B8614 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Shure
- manuels d’utilisations 27B8614
- fiches produit Shure
- dépliants
- ou étiquettes-énergie Shure 27B8614
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Shure 27B8614.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Shure 27B8614, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Shure 27B8614. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Shure 27B8614.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Shure 27B8614, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Shure 27B8614 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Shure 27B8614.

Le manuel d’utilisation complet Shure, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Shure 27B8614 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Shure 27B8614, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lShure 27B8614 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Shure 27B8614 - qui devraient nous aider dans les premières étapes lors de l'utilisation Shure 27B8614
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Shure 27B8614
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Shure 27B8614 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Shure 27B8614?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Shure 27B8614, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Shure 27B8614 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)