Français dropdown-ico

Manuel d’utilisation Bostitch GT18B01

30 pages 1.72 mb
Télécharger

Aller à la page of 30

Summary
  • Bostitch GT18B01 - page 1

    1 GT18B01 HYDRAULIC POWER UNIT S AFETY , O PERA TION AND M AINTENANCE SER VICE MANUAL WARNING Stanley Hydraulic T ools 3810 SE Naef Road Milwaukie OR 97267-5698 503-659-5660 F AX 503-652-1780 www .stanley-hydraulic-tools.com Copyright © 2004, The Stanley W orks OPS/MAINT USA 65466 9/2004 V er 1 ...

  • Bostitch GT18B01 - page 2

    2 ...

  • Bostitch GT18B01 - page 3

    3 T ABLE OF CONTENTS For the nearest authorized and certifi ed dealer , call Stanley Hydraulic T ools at the number listed on the back of this manual and ask for a Customer Service Representative. SERVICING THE ST ANLEY POWER UNIT : This manual contains safety , operation, and routine mainte- nance instructions. Stanley Hydraulic T ools recommends ...

  • Bostitch GT18B01 - page 4

    4 CERTIFICATE OF CONFORMITY Hy draulic Tools ______________________________________________________________________ I, the undersigned: Burrows, James Surname and First names Hereby certify that the c onstruction plant or equipment specif ied hereunder: 1. Manufacturer: Stanley Hydraulic Tools, 3810 Naef Road, Milwauki e, Oregon USA 2. Representati ...

  • Bostitch GT18B01 - page 5

    5 Safety symbols and signal words, as shown below , are used to emphasize all operator , maintenance and repair actions which, if not strictly followed, could result in a life-threatening situation, bodily injury or damage to equip- ment. This safety alert and signal word indicate an imminently hazardous situa- tion which, if not avoided, will resu ...

  • Bostitch GT18B01 - page 6

    6 T ool operators and maintenance personnel must always comply with the safety precau- tions given in this manual and on the stickers and tags attached to the equipment. These safety precautions are given for your safety . Review them carefully before operat- ing the tool and before performing general maintenance or repairs. Supervising personnel s ...

  • Bostitch GT18B01 - page 7

    7 T OOL STICKERS & T AGS 65458 Sound Power Decal 62302 Power Unit Dash Decal 62300 CHOKE D ANGER PULL TO ST ART PUSH TO R UN 62300 Single Circuit 28322 CE Decal AUTO IDLE OFF AUTO IDLE ON R U 62302 ...

  • Bostitch GT18B01 - page 8

    8 HOSE TYPES Hydraulic hose types authorized for use with Stanley Hydraulic T ools are as follows: ➊ Certifi ed non-conductive ➋ Wire-braided (conductive) ➌ Fabric-braided (not certifi ed or labeled non-conductive) Hose ➊ listed above is the only hose authorized for use near electrical conductors. Hoses ➋ and ➌ listed above are conduc ...

  • Bostitch GT18B01 - page 9

    9 HTMA REQUIREMENTS FLOW RA TE TOOL OPERA TING PRESSURE (at the power supply outlet) SYSTEM RELIEF V AL VE SETTING (at the power supply outlet) MAXIMUM BACK PRESSURE (at tool end of the return hose) Measured at a max. fl uid viscosity of: (at min. operating temperature) TEMPERA TURE Suffi cient heat rejection capacity to limit max. fl uid temper ...

  • Bostitch GT18B01 - page 10

    10 Chevron A W-MV -32 Exxon "Univis" J-26 Mobil D.T .E. 13 Gulf "Harmony" AW -HVI-150-32 Shell "T ellus" T -32 T exaco "Rando" HD-AZ Union "Unax" AW -WR-32 T erresolve EnviroLogic 132 4. HYDRA ULIC CONNECTIONS The recommended hose length is 25 ft/8 m with a 1/2 inch/12.7 mm inside diameter . The hos ...

  • Bostitch GT18B01 - page 11

    11 CONTROL P ANEL RETURN PRESSURE H.T .M.A. 1/2 INCH MALE QUICK DISCONNECT COUPLER H.T .M.A. 1/2 INCH FE- MALE QUICK DISCON- NECT COUPLER 1/2 INCH I.D. HOSE, 25 FT LONG WITH 2500 PSI/ 172 BAR RA TING AND 4 T O 1 SAFETY F ACTOR PRESSURE RETURN 1/2 INCH MALE PIPE HOSE END 1/2 INCH MALE PIPE HOSE END ADAPTER, 3/8 INCH MALE PIPE x -8 SAE O-RING H.T .M. ...

  • Bostitch GT18B01 - page 12

    12 CONTROLS This unit is equipped with an advanced proportional engine control system. It provides a means of controlling engine speed by adjusting the fuel control lever with an actuator . The Power Unit provides one circuit, with an oil fl ow of 5 gpm/19 lpm up to 2000 psi/140 bar or 8 gpm/30 lpm up to 2000 psi/140 bar with a factory-programmed ...

  • Bostitch GT18B01 - page 13

    13 OPERA TION COLD WEA THER ST ARTUP 1. Use the procedures described under "ST ARTUP" and then follow the procedure below . 2. Hydraulic fl uids are thicker in cold weather . Therefore, it is recommended that the engine be run at low idle long enough to bring the fl uid temperature up to a minimum of 50°F/10°C. 3. If the tools and too ...

  • Bostitch GT18B01 - page 14

    14 ST ORAGE • Clean the unit thoroughly before storage. Do not use water pressure. • Always store the unit in a clean and dry facility . • If the unit will be stored for a prolonged period (over 30 days), add a fuel additive to the fuel tank to prevent the fuel from gumming. Run engine for a short period to circulate the additive. • Replace ...

  • Bostitch GT18B01 - page 15

    15 CHECKING PERFORMANCE CONTROL™ (ELECTRONIC GOVERNOR-ST A TIC CHECK) T o determine whether a governor problem is being caused by the actuator or the control module, perform the following static check exactly in order shown. A pair of jumper wires and a known good 12-volt battery is required. 1. Disconnect red and green wires from the control mod ...

  • Bostitch GT18B01 - page 16

    16 F AUL T CODES 1 APECS unit not calibrated yes Have engine serviced by an Authorized Stanley Dealer . 2 Engine speed excessive yes Have engine serviced by an Authorized Stanley Dealer . 3 Engine speed unusually low yes Have engine serviced by an Authorized Stanley Dealer . 4 Engine shutdown due to engine yes Have engine serviced by an Authorized ...

  • Bostitch GT18B01 - page 17

    17 GENERAL T ests and adjustments should be performed periodically to ensure the power unit is operating at maximum effi ciency . Stanley Circuit T ester (part number 04182) is recommend- ed. This tester can be used to isolate problems in both the engine and hydraulic system prior to any power unit disas- sembly . TESTING THE HYDRAULIC CIRCUIT The ...

  • Bostitch GT18B01 - page 18

    18 Engine will not start. Flow selector switch not in the Make sure the fl ow selector switch is in OFF position. the OFF position when starting. Battery not connected. Attach battery cables, check wires. Weak battery . T est battery , charge or replace. No fuel. Add Fuel. Fuel fi lter plugged. Replace fuel fi lter . Defective spark plugs. Remov ...

  • Bostitch GT18B01 - page 19

    19 Engine: ....................................................................................................................... ........................................ 18 hp Briggs Capacity .......................................................................................... One 5 gpm/19 lpm Circuit or One 8 gpm/30 lpm Circuit Length: .... ...

  • Bostitch GT18B01 - page 20

    20 SER VICE GENERAL Service instructions in this section are limited to parts and components other than the engine and hydraulic pump. Other major components should be serviced by representa- tives of the respective manufacturers as follows: ENGINE - Briggs and Stratton V anguard OHV Model-356447-01 15-E1 The Briggs engine should be serviced only b ...

  • Bostitch GT18B01 - page 21

    21 Be sure the tapered cone surfaces of the bushing and blower hub are clean and free of anti-seize lubricants. CA UTION 2. Disconnect the wiring harness (See Figure 4, Wiring Diagrams for the correct connections). 3.Follow steps 1 through 4 under "Manifold Assembly Re- moval". 4. Remove the RED wire attached to the starter solenoid and t ...

  • Bostitch GT18B01 - page 22

    22 Assemble the bushing and blower hub with the bolts inserted (but not tightened) through the drilled holes in the blower hub and into the tapped holes in the bushing. With the key in the shaft, slide assembly into position on the shaft and tighten the setscrew over the key (if equipped). T ighten the 3 capscrews (14, fi g.1) alternately and even ...

  • Bostitch GT18B01 - page 23

    23 SER VICE HYDRAULIC T ANK, COOLER & FIL TER ASSEMBL Y (see fi gure 1, 2 & 3) 1. First remove the hydraulic fl uid from the tank by either pumping it out with a portable drill pump or draining it into a container . 2. Remove the cooler guard (20, fi g. 2) by removing the 2 hex fl ange bolts (9, fi g. 2) and 2 capscrews (21, fi g. 1). ...

  • Bostitch GT18B01 - page 24

    24 FIGURE 1. BRIGGS ENGINE ASSEMBL Y 5 6 3 5 3 7 3 4 3 6 5 2 4 4 2 7 5 0 5 1 8 2 6 2 8 4 5 3 0 4 3 3 0 4 7 3 3 3 1 3 0 3 2 2 9 4 9 4 8 1 7 1 6 1 4 1 3 1 2 1 1 9 1 0 4 1 5 2 0 2 1 2 3 1 8 2 5 2 2 1 9 4 1 4 0 3 9 3 8 7 2 1 3 4 6 5 4 5 3 4 4 2 4 5 5 5 7 5 8 5 6 4 2 5 4 4 8 5 9 4 1 1 ...

  • Bostitch GT18B01 - page 25

    25 ITEM P/N Q T Y DESCRIPTION 1 36150 1 Muffl er 1A 65456 1 Spark Arrester 2 36151 1 Heat Shield 3 36152 2 Screw , Hex W asher 4 59007 1 Briggs Engine 5 56656 1 Coupling 6 07819 1 Square Key 7 07860 2 Capscrew , 3/8-16 x 1-1/4 8 31765 1 Pressure Switch 9 12787 4 Flange Nut 10 24287 1 Clamp 1 1 59076 1 Bushing 12 20990 1 Key 13 59103 1 Blower Hub 1 ...

  • Bostitch GT18B01 - page 26

    26 FIGURE 2. FRAME P ARTS ITEM P/N Q T Y DESCRIPTION 1 370502 7 Capscrew , 5/16 in. -18 UNC 2 03906 7 Nylock Nut, 5/16 in. -18 UNC 3 62270 1 Handle, Rear Lift 4 58857 1 Coupler , Male 3/8 in., -8 SAE 5 58856 1 Coupler , Female 3/8 in., -8 SAE 6 60962 2 Capscrew , 1/4 in. -20 7 59130 1 Manifold Assy , Single Circuit 8 1 Dash Decal 9 59074 6 Hex Flan ...

  • Bostitch GT18B01 - page 27

    27 ITEM P/N QTY DESCRIPTION 1 59130 1 Manifold Assy , Single Circuit 2 59104 1 Hose Barb, 3/4 in. Hose x 3/4 in. Pipe 3 62199 4 Hose Clamp 4 350000 1 Elbow , 45° Straight Thread 5 02773 1 Adapter 6 58569 1 Elbow , 90° 7 58943 1 Hose 8 350104 1 Connector , Straight Thread 9 40364 1 Elbow , 45° 10 59088 1 Hose 1 1 59089 1 Hose 12 59105 1 Hose Barb ...

  • Bostitch GT18B01 - page 28

    28 RECTIFIER WIRE WHITE CONTROLLER TO MAGNETO WIRE ON ENGINE GRA Y WIRE OIL PRESSURE SWITCH FUEL SHUTOFF RED WIRE - THROTTLE CONTROL SWITCH (NOTE: PLUG BEHIND SWITCH WITH BLUE & YELLOW WIRES GOES T O SWITCH ON TOP) RELA Y -62301 SUPPLIED W/62293 HARNESS PRESSURE SWITCH TO AC TUATOR RED/GREEN GROUND WIRES MANIFOLD ASSY DIRECTIONAL V AL VE RED TO ...

  • Bostitch GT18B01 - page 29

    29 Stanley Hydraulic T ools (hereinafter called “Stanley”), subject to the exceptions contained below , warrants new hydraulic tools for a period of one year from the date of sale to the fi rst retail purchaser , or for a period of 2 years from the shipping date from Stanley , whichever period expires fi rst, to be free of defects in material ...

  • Bostitch GT18B01 - page 30

    30 Stanley Hydraulic T ools 3810 SE Naef Road Milwaukie OR 97267-5698 503-659-5660 F AX 503-652-1780 www .stanley-hydraulic-tools.com ...

Fabricant Bostitch Catégorie Automobile Parts

Les documents que nous recevons du fabricant de l'appareilBostitch GT18B01 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Bostitch
- manuels d’utilisations GT18B01
- fiches produit Bostitch
- dépliants
- ou étiquettes-énergie Bostitch GT18B01
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Bostitch GT18B01.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Bostitch GT18B01, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Bostitch GT18B01. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Bostitch GT18B01.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Bostitch GT18B01, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Bostitch GT18B01 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Bostitch GT18B01.

Le manuel d’utilisation complet Bostitch, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Bostitch GT18B01 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Bostitch GT18B01, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lBostitch GT18B01 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Bostitch GT18B01 - qui devraient nous aider dans les premières étapes lors de l'utilisation Bostitch GT18B01
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Bostitch GT18B01
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Bostitch GT18B01 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Bostitch GT18B01?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Bostitch GT18B01, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Bostitch GT18B01 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (1)

Alenka

Dobry den.Viete mi poslat manual navod tricity coffee maker tcm10 navod sk.Dakujem