Français dropdown-ico

Manuel d’utilisation Cisco Systems ASR1002

36 pages 1.66 mb
Télécharger

Aller à la page of 36

Summary
  • Cisco Systems ASR1002 - page 1

    Q UICK S TART G UIDE Cisco ASR 1002 Router 1 Documentation and R esources 2 Prepare for Installation 3 Rac k-Mount the Router 4 Connect the Rou ter to the Network 5 Star t the System 6 Configuring the R outer 7 After Installation ...

  • Cisco Systems ASR1002 - page 2

    2 1 Documentation and Resources Documentation for the Cisco 1000 Series Ag gregation Services Routers documen tation is online with the exception of the regulatory compliance a nd sa fety documentation and the Cisco 1000 Se ries Aggregation Servic es Routers documentation flyer . For detailed hardware installation i nstructions, refer to the online ...

  • Cisco Systems ASR1002 - page 3

    3 2 Prepare for Installation This section contains information about tools and parts, wa rnings, site preparation information, and information for rack-mount and equipment shelf or tabletop in stallation. War n in g Only trained and qualified p ersonnel should instal l, replace, or service this equipment. Statement 1030 Caution The eUSB panel door ...

  • Cisco Systems ASR1002 - page 4

    4 Prepare for Rack-Mount Installation Before you begin the rack-mounting tasks: • Decide whether or not you want to front-mount or rear -mount the chassis. • Decide whether or not you want to attach ca ble-management brackets to your chassis. Note If you install cable-management bracke ts, make certain th at you use the spec ified rack-mount ea ...

  • Cisco Systems ASR1002 - page 5

    5 Attach the Rack-Mount Bracke ts—Chassis Rear-Mounted T o install the rack-mount on a Cisco ASR 1002 Router fo r a rear rack-mount configuration, follow these steps: Step 1 Locate the threaded ear holes in the rear sides of the chassis. Step 2 Position the rear rack-mount bracket t op hole with the chassis from the back (See Figure 2 ).Make cert ...

  • Cisco Systems ASR1002 - page 6

    6 Figure 3 shows the Cisco ASR 1 002 Router in a four -post rack. Figur e 3 Installing the Cisco A SR 1 0 02 Router in a F our -Post Rac k - Fr ont and Rear Rack-Mounting Note Because the rack-mount brack ets support the weight of the entire chassis, be sure to use all screws to fasten the two rack-mount brackets on the chassis to the rack posts. N ...

  • Cisco Systems ASR1002 - page 7

    7 Ti p T o allow spac e to attach the cable-management brackets to the c hassis in the rack easily , make certain that you use th e rack-mount bracket ear holes specified in Step 9. Step 8 Hold the chassis in position against th e mounting rails and follow these steps: a. Insert the bottom screw into the second ear hole from the bo ttom of the rack ...

  • Cisco Systems ASR1002 - page 8

    8 Caution If you are using a two-post rack, secure the rack to the floor surface to prevent tipping and avoid bodily injury and component damage. Step 1 Pos ition the chassis so the front is clos est to you and lift it carefully into the rack. T o prevent injury , avoid any sudden twists or moves. Step 2 Slide the chassis into the rack, pushing it ...

  • Cisco Systems ASR1002 - page 9

    9 Figure 5 Attac hing the Cabl e-Management Brack et to the Cisco ASR 1 0 02 Router Step 3 Using the bottom rack-mount ear hole, insert the screw th rough cable-management bracket and into the chassis rack-mount bracket. Figure 5 shows the cable-management brac kets attached to the chassis. Step 4 Using a Phillips screwdriver and the cabl e-managem ...

  • Cisco Systems ASR1002 - page 10

    10 Figur e 6 Cisco A SR 1 002 Router Gr ound Connect or Locati on and eUSB P anel Door Step 1 Use the wire stripper to strip one end of the A W G #6 wire approximately 0.75 inches (19.05 mm). Step 2 Insert the A WG #6 wire into the wi re receptacle on the grounding lug. Step 3 Use the manufacturer ’ s recommended crimping tool to carefu lly crimp ...

  • Cisco Systems ASR1002 - page 11

    11 Step 5 Locate the chassis gro und connector on the side of your c hassis. Step 6 Insert the two screws through the holes in the groundi ng lug. Step 7 Use the Number 2 Phillips screwdriver to carefully ti ghten th e screws until the grounding lug is held firmly to the chassis. Do not overtighten the screws. Step 8 Connect the opposite end of the ...

  • Cisco Systems ASR1002 - page 12

    12 Figur e 8 Cisco ASR 1 0 02 Integr at ed Rout e Processor Console and A uxiliary Por t Connectors Step 3 After you establish normal router operat ion, you can disconnect th e terminal. Note For console and auxiliary port pino uts, se e Cisco ASR 1002 rou ter specifications in the Cisco ASR 1000 Series Aggregation Services Routers Hardware Inst al ...

  • Cisco Systems ASR1002 - page 13

    13 Step 3 Configure to a fixed speed through th e command-line interface (CLI) commands. Connect the Shared Port Adapter Cables The instructions for connecting the cables for the shared port adapters installed in the Cisco ASR 1002 Router are con tained in the Cisco ASR 1000 Series Aggregati on Services Routers SP A a nd SIP Hardware Installation G ...

  • Cisco Systems ASR1002 - page 14

    14 Proceed to the “Start the System” section on page 14 to complete the installation . 5 Start the System Before you start the system, yo u must connect power to it. Connect AC Power to t he Cisco ASR 1002 Router This section provides instructions for installing the AC power su pply into the Cisco A SR 1002 Router . Read the safety warnings bef ...

  • Cisco Systems ASR1002 - page 15

    15 Figur e 1 1 AC P ow er Supply for the Cisco A SR 1 002 Router Table 1 describes the AC power suppl y LEDs on the Cisco ASR 1002 Router . T able 1 Cisco ASR 1 0 02 Router AC P ower Supply LEDs Note T o connect an AC power sup ply to the Cisco ASR 1002 Router , follow the steps in Installing the AC Power Supply, page 31 . Connect DC Power to t he ...

  • Cisco Systems ASR1002 - page 16

    16 Figure 12 shows the DC power supply for the Cisco ASR 1002 Router . Figur e 12 DC P o wer Su pply fo r the Cisco A SR 1 0 02 Router Table 2 describes the DC power suppl y LEDs on the Cisco ASR 1002 Router . T able 2 Cisco ASR 1 0 02 Router DC P ow er Supply LEDs T o connect the DC power sup ply to a Cisco ASR 1002 Router , follow these steps: St ...

  • Cisco Systems ASR1002 - page 17

    17 Note The color coding of the DC-input power supply leads depends on the color coding of the DC power source at your site. T ypically , green or green/yellow is used for ground. Make ce rtain the lead color co ding you choose for the DC-input power supply matches lead colo r codi ng used at the DC power source. War n in g When you install the uni ...

  • Cisco Systems ASR1002 - page 18

    18 Step 9 Connect the ground, positive, and ne gative leads to the power source. Step 10 T urn the branch source breake r on. Step 11 T urn the power supply sw itch to the On (I) position. Step 12 V erify that the LED s illuminate. This completes the procedure fo r connecting DC-input power . Verifying Power Su pply operation Follo w this procedure ...

  • Cisco Systems ASR1002 - page 19

    19 Step 1 T urn on power . The green OK LED on the power supply tu rns on. (Both power supplies are required in the Cisco ASR 1002 Router .) Step 2 Listen for the fans; you should immediately hear th em operating. Step 3 During the boot process, observe the system LEDs. The po wer LED should be green. The ST A TUS LED lights yellow to indicate boot ...

  • Cisco Systems ASR1002 - page 20

    20 Table 4 pro vides information about the Cisco ASR1 000-ESP5 LED s in the Cisco ASR 1002 Router as the system starts. T able 4 Cisco ASR1 0 00-ESP5 and ASR1 0 00-ESP1 0 LED Activity During the boot process, observe the syst em LEDs. The ST A TUS LED comes on immediatel y as amber , then turns to green when the Cisco IOS is booted. Note The system ...

  • Cisco Systems ASR1002 - page 21

    21 %IOSXEBOOT-4-DEBUG_CONF: (rp/0): Using DEBUG_CONF file /misc/scratch/debug.conf Feb 13 13:00:38.546 R0/0: %PMAN-3-PROCFAIL_IGNORE: All process failures are being ignored due to debug settings. FRU may not reset automatically Restricted Rights Legend Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subp ...

  • Cisco Systems ASR1002 - page 22

    22 *Feb 13 13:01:28.701: %LINK-5-CHANGED: Interface GigabitEthernet0, changed state to administratively down *Feb 13 13:01:29.728: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to down *Feb 13 13:01:14.738: %CPPHA-7-SYSREADY: F0: cpp_ha: CPP client process FMAN-FP (5 of 5) ready. *Feb 13 13:01:14.895: %IOSXE-6-PLAT ...

  • Cisco Systems ASR1002 - page 23

    23 Router> enable Step 3 At the password prompt, enter your system password. If an en able password has not been se t on your system, this step may be skipped. The following example shows entry of the password ca lled enablepass : Password: enablepass Step 4 When your enable password is accepted, the priv ileged EXEC configuration mode promp t a ...

  • Cisco Systems ASR1002 - page 24

    24 for management of the system, extended setup will ask you to configure each interface on the system Would you like to enter basic management setup? [yes/no]: n First, would you like to see the current interface summary? [yes]: y Any interface listed with OK? value "NO" does not have a valid configuration Interface IP-Address OK? Method ...

  • Cisco Systems ASR1002 - page 25

    25 no ip address ! interface GigabitEthernet0/0/1 shutdown no ip address ! interface GigabitEthernet0/0/2 shutdown no ip address ! interface GigabitEthernet0/0/3 shutdown no ip address ! interface GigabitEthernet0/1/0 shutdown no ip address ! interface GigabitEthernet0/1/1 shutdown no ip address ! interface FastEthernet0/3/0 shutdown no ip address ...

  • Cisco Systems ASR1002 - page 26

    26 Enter your selection [2]: Router#reload Proceed with reload? [confirm] *Jan 11 06:59:29.476: %SYS-5-RELOAD: Reload requested by console. Reload Reason: Reload command. System Bootstrap, Version 12.2(20071105:235056) [gschnorr-mcp_rommon_rel_1_25 101], DEVELOPMENT SOFTWARE Copyright (c) 1994-2007 by cisco Systems, Inc. Compiled Mon 05-Nov-07 16:5 ...

  • Cisco Systems ASR1002 - page 27

    27 Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (c) of the Commercial Computer Software - Restricted Rights clause at FAR sec. 52.227-19 and subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at DFARS sec. 252.227-7013. cisco Systems, Inc. 170 West Tasm ...

  • Cisco Systems ASR1002 - page 28

    28 Save the Running Conf iguration to NVRAM T o store the configuration or changes to your startup configur ation in NVRAM, use the copy run ning-config startup-config command to save your configura tion changes to the startup config uration so that the changes will not be lost if the software reloads or a powe r outage occu rs. For example : Route ...

  • Cisco Systems ASR1002 - page 29

    29 Power Off the Cisco ASR 1002 Router This section explains how to shut down the Cisco ASR 1002 Router . It is recommended that before turning off all power to the chassis, you issue the reload command. This insures that the operating system cleans up all the file systems. Once the reloa d operation is complete, then the Cisco ASR 1000 Series rout ...

  • Cisco Systems ASR1002 - page 30

    30 Step 2 Using the handles on both sides of the module, with two ha nds, gently insert the Cisco ESP5 or -ESP10 into the top chassis slot. Note Handle the Cisco ESP5 and ESP10 by the carrier edges only ; never touch the printed circuit board components or connector pins. Step 3 Once the board is seated, tighten the captive screws. Step 4 Place the ...

  • Cisco Systems ASR1002 - page 31

    31 Step 9 Power on the router by turning the power switch to the on (I) position. Replace a Power Supply in the Cisco ASR 1002 Router This section provides instructions for removing and replaci ng the AC power supply and the DC power supply in a Cisco ASR 1002 Router . Before you begin, make certain the chassis is gr ounded. T wo power supplies mus ...

  • Cisco Systems ASR1002 - page 32

    32 Figur e 14 Cisco ASR 1 0 02 Router A C P ower Cord b. T ake the power cord and run it below the handles of the pow er supply in slot 1 (the power supply you are connecting) and the power supply in slot 0 (left) as shown in Figure 15 . Make sure the power cord is hanging loosely so that it cannot be disconnected from the AC power inlet. Figur e 1 ...

  • Cisco Systems ASR1002 - page 33

    33 Note Using a tie wrap for the AC pow er cable is optional and n o t necessary . However , if you do attach the AC power cable to a power supply tab and th en you remo ve the AC power cable for some reason, check for any damage to the cable after you cut the tie wrap off. If the powe r cord is damaged, replace it immediately . Note T urn the powe ...

  • Cisco Systems ASR1002 - page 34

    34 Step 7 Replace the DC power supply within five minutes o r the system will shutdown. Y ou have completed the procedure for removing a DC pow er supply from the Cisco ASR 1002 Ro uter . Installing the DC Power Supply This section provides information about replacing a DC power suppl y in the Cisco ASR 1002 Router . Note The color coding of the DC ...

  • Cisco Systems ASR1002 - page 35

    35 Figur e 18 Cisco ASR 1 0 02 Ro uter DC Po wer Supply Step 5 Insert the stripped end of the ground lead all the w ay into th e ground lead receptacle on the DC-input power supply , and tighten the receptacle screw usi ng a 3.5 mm fla t-blade screwdriver to a torque of 0.5 to 0.6Nm. Step 6 Insert the s tripped end of the positive le ad all the wa ...

  • Cisco Systems ASR1002 - page 36

    Americas Headquarters Cisco Systems, Inc. 170 W est T asman Drive San Jose, CA 95134-1706 USA www .cisco.com T el: 408 526-4000 800 553-NETS (6387) Fax: 408 527-0883 Asia Pacific Headquarters Cisco Systems, Inc. 168 Robinson Road #28-01 Capital T ower Singapore 068912 www .c isco.com T el: +65 6317 7 777 Fax: +65 6317 7799 Europe Headquarters Cisco ...

Fabricant Cisco Systems Catégorie Network Router

Les documents que nous recevons du fabricant de l'appareilCisco Systems ASR1002 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Cisco Systems
- manuels d’utilisations ASR1002
- fiches produit Cisco Systems
- dépliants
- ou étiquettes-énergie Cisco Systems ASR1002
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Cisco Systems ASR1002.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Cisco Systems ASR1002, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Cisco Systems ASR1002. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Cisco Systems ASR1002.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Cisco Systems ASR1002, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Cisco Systems ASR1002 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Cisco Systems ASR1002.

Le manuel d’utilisation complet Cisco Systems, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Cisco Systems ASR1002 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Cisco Systems ASR1002, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lCisco Systems ASR1002 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Cisco Systems ASR1002 - qui devraient nous aider dans les premières étapes lors de l'utilisation Cisco Systems ASR1002
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Cisco Systems ASR1002
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Cisco Systems ASR1002 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Cisco Systems ASR1002?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Cisco Systems ASR1002, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Cisco Systems ASR1002 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)