Français dropdown-ico

Manuel d’utilisation KTM EXC-F 400 XC-W

68 pages 5.38 mb
Télécharger

Aller à la page of 68

Summary
  • KTM EXC-F 400 XC-W - page 1

    KTM-Sportmotorcycle AG A–5230 Mattighofen www.ktm.at KTM Group Partner 5/2006 FOTO: MITTERBAUER 250 XC-F, XCF-W, EXC-F 400 XC-W, EXC RACING 450 XC, XC-W, EXC RACING 525 XC, XC-W, EXC RACING 525 XC DESERT RACING OWNER’S MANUAL 2007 ART. NR. 3.211.145 EN ENGLISH ...

  • KTM EXC-F 400 XC-W - page 2

    ENGLISH 1 INTRODUCTION » Please insert the serial numbers of your motorcycle in the boxes below Frame number Engine number Key number Stamp of dealer All information contained is without obligation. KTM-Sportmotorcycle AG particularly reserves the right to modify any equipment, technical specifications, prices, colors, shapes, materials, services, ...

  • KTM EXC-F 400 XC-W - page 3

    ENGLISH 2 IMPORTANT INFORMATION » INTENDED PURPOSE KTM sports motorcycles are designed and constructed to resist the usual wear and tear of normal use in competitions. The motorcycles comply with the regulations and categories currently in effect with the leading interna- tional motorcycle associations. The XC and other „competition only“ labe ...

  • KTM EXC-F 400 XC-W - page 4

    ENGLISH 3 IMPORTANT INFORMATION » W e expressly point out that work marked with an asterisk in the chapter „Maintenance work on the chas- sis and engine“ must be performed. If maintenance work should become necessary during a competition it should be performed by a trained mechanic. KTM strongly recommends that all service work to your KTM sho ...

  • KTM EXC-F 400 XC-W - page 5

    TABLE OF CONTENTS » ENGLISH 4 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 IMPOR T ANT INFORMA TION . . . . . . . . . . . . . . . . . . . . . . . .2 SERIAL NUMBER LOCA TIONS . . . . . . . . . . . . . . . . . . . . . .5 Engine number , engine type . . . . . . . . . . . . . . . . . . . . . .5 Chassis number . . . . ...

  • KTM EXC-F 400 XC-W - page 6

    SERIAL NUMBER LOCATIONS » Chassis number The chassis number is stamped on the right side of the steering head tube. Enter this number in the field on page no 1. Engine number, engine type The engine number and the engine type are stamped into the left side of the engine below the engine sprocket. Enter this number on page 1. ENGLISH 5 ...

  • KTM EXC-F 400 XC-W - page 7

    A B C OPERATION INSTRUMENTS » Hand brake lever The hand brake lever [3] is mounted on the handlebars on the right and actuates the front wheel brake. The adjusting screw [B] can be used to change the basic position of the hand brake lever (see "Maintenance"). Combination switch (EXC) The light switch has 2, respectively 3 switch position ...

  • KTM EXC-F 400 XC-W - page 8

    OPERATION INSTRUMENTS » Headlamp switch (XC-W) In this model the headlamp is switched on with the pull switch [1] . Flasher switch The flasher switch is a separate unit and is mounted on the left portion of the handlebar . The wire harness is designed in a way that whenever you want to use your bike off-road, you can dismount the entire turn indic ...

  • KTM EXC-F 400 XC-W - page 9

    OPERATION INSTRUMENTS » ENGLISH 8 TEST All of the display segments briefly light up for the display function test. WS (wheel size) The display changes and the circumference of the front wheel is briefly dis- played in millimeters (2205 mm corresponds to a front wheel circumference of 21" with production tires). Afterwards the display will ret ...

  • KTM EXC-F 400 XC-W - page 10

    OPERATION INSTRUMENTS » ENGLISH 9 SPEED / LAP (lap time) display mode Y ou can use the manual stop watch to stop and store up to 10 lap times, which you can view in the LAP/LAP display mode (see below). LAP displays the lap times in hours, minutes and seconds. + button Starts and stops the stop watch, lap time is not reset to 0 – button Stops th ...

  • KTM EXC-F 400 XC-W - page 11

    OPERATION INSTRUMENTS » ENGLISH 10 LAP / LAP display mode (to view lap times) The LAP/LAP display mode will only be shown if lap times have been stored and the front wheel has stopped. It will display the lap number and the stopped lap time in hours, minutes and seconds. Press the + button to access the next lap time. T o clear all of the stored l ...

  • KTM EXC-F 400 XC-W - page 12

    OPERATION INSTRUMENTS » ENGLISH 11 Kilometers or miles The unit (kilometers or miles) can also be changed. The ODO figure will be retained and converted accordingly . The TR1, A1, S1, TR2 and A2 figures will be cleared. T o select the unit, select the SPEED/H mode and hold the | button for 3 sec- onds to access the SETUP menu. Press the | button u ...

  • KTM EXC-F 400 XC-W - page 13

    OPERATION INSTRUMENTS » ENGLISH 12 Setting the clock T o set the clock, switch the ignition off and select the SPEED/CLK mode. Press and hold the | button for 3 seconds. The blinking digits can be changed using the + and - buttons. Press the | button to move to the next digit. 0- 12 will show the time in the 12-hour mode, 0-24 in the 24-hour mode. ...

  • KTM EXC-F 400 XC-W - page 14

    OPERATION INSTRUMENTS » ENGLISH 13 1 2 XC EXC Filler cap (bayonet cap) To open the filler cap: T urn the filler cap 45 ° counter -clockwise. To close the filler cap: Put the filler cap on and turn it 45 ° clockwise. Filler cap (screw cap) To open the filler cap: T urn the filler cap counter -clockwise. To close the filler cap: Put the filler cap ...

  • KTM EXC-F 400 XC-W - page 15

    OPERATION INSTRUMENTS » ENGLISH 14 2,3,4 (5,6) 1 N 1 Shift lever The shift lever is mounted on the left side of the engine. The position of the gears is shown in the illustration. Neutral, or the idle speed, is located between first and second gear . Kickstarter The kickstarter is mounted on the right side of the engine. Its upper part can be swiv ...

  • KTM EXC-F 400 XC-W - page 16

    1 2 2 3 3 5 6 4 OPERATION INSTRUMENTS » ENGLISH 15 Compression damping of fork Hydraulic compression damping determines the reaction when the fork is com- pressed. The degree of compression can be adjusted with adjusting screws at the bottom of the fork legs.Remove the protecting cap [1] . T urn the adjusting screws [2] clockwise to increase dampi ...

  • KTM EXC-F 400 XC-W - page 17

    OPERATION INSTRUMENTS » ENGLISH 16 2 1 4 3 Compression damping of shock absorber (XC-W, EXC) The compression damping (during compression) can be adjusted for these shock absorbers (Mono Compression Control). The degree of damping can be adjusted by turning adjusting screw [1] with a screwdriver . T urning in a clockwise direction will increase the ...

  • KTM EXC-F 400 XC-W - page 18

    GENERAL TIPS AND WARNINGS FOR STARTING THE MOTORCYCLE » ENGLISH 17 – W ear suitable clothing when driving a motorcycle. Clever KTM drivers always wear a helmet, boots, gloves and a jacket, regard- less of whether driving all day or just for a short trip. The protective clothing should be brightly colored so that other vehicles can see you as ear ...

  • KTM EXC-F 400 XC-W - page 19

    1 DRIVING INSTRUCTIONS » ENGLISH 18 A B Check the following before each start When you start off, the motorcycle must be in perfect technical condition. For safety reasons, you should make a habit of performing an overall check of your motorcycle before each start. The following checks should be performed: 1 CHECK THE OIL LEVEL Insufficient oil re ...

  • KTM EXC-F 400 XC-W - page 20

    2 DRIVING INSTRUCTIONS » ENGLISH 19 – Always kick the kickstarter briskly all the way without opening the throt- tle. If you do not Kick hard enought, with an open throttle grip, the kick- back hazard will be higher . – Do not start the engine and allow it to idle in a closed area. Exhaust fumes are poisonous and can cause loss of consciousnes ...

  • KTM EXC-F 400 XC-W - page 21

    DRIVING INSTRUCTIONS » ENGLISH 20 35 mm NOTE: Dedicated to nothing but offroad racing, XC/EXC models make no compromises in their design. As such, they do not include any radi- ator fan, and the size of the radiator is dimensioned for optimum ergonomics. In normal racing, the cooling system is sufficient. If you use your motorbike in other conditi ...

  • KTM EXC-F 400 XC-W - page 22

    PERIODIC MAINTENANCE » ENGLISH 21 250-F 2007 A CLEAN MOTORCYCLE CAN BE CHECKED MORE QUICKLY WHICH SAVES MONEY! 1st service after 3 hours or 20 l fuel every 20 hours or 140 l fuel or 1 race ENGINE Change engine oil, oil filter z z Clean oil screen and drain plug magnet z z Replace spark plug (after 30 hours) Check and adjust valve clearance z z Che ...

  • KTM EXC-F 400 XC-W - page 23

    PERIODIC MAINTENANCE » ENGLISH 22 NOTE: If the inspection establishes that permissible tolerances are exceeded, the respective components must be replaced. 250-F 2007 IMPORTANT CHECKS AND MAINTENANCE TO BE CARRIED OUT BY THE RIDER Before each start After every cleaning For cross- country use at least once a year Check oil level z Check brake fluid ...

  • KTM EXC-F 400 XC-W - page 24

    PERIODIC MAINTENANCE » ENGLISH 23 Service intervalls should never be exceeded by more than 2 hours or 15 liters of fuel. Maintenance work done by KTM authorised workshops is not a substitute for care and checks done by the rider . 400/450/525 2007 A CLEAN MOTORCYCLE CAN BE CHECKED MORE QUICKLY WHICH SAVES MONEY! 1st service after 3 hours or 20 l f ...

  • KTM EXC-F 400 XC-W - page 25

    PERIODIC MAINTENANCE » ENGLISH 24 400/450/525 2007 IMPORTANT CHECKS AND MAINTENANCE TO BE CARRIED OUT BY THE RIDER Before each start After every cleaning For cross- country use At least once a year Check oil level z Check brake fluid level z Check brake pads for wear z Check lights for function z Check horn for function z Lubricate and adjust cabl ...

  • KTM EXC-F 400 XC-W - page 26

    PERIODIC MAINTENANCE » ENGLISH 25 400/450/525 2007 IMPORTANT INSPECTIONS OR MAINTENANCE WORK THAT MUST BE PERFORMED BY THE SPECIALIZED KTM WORKSHOP FOR COMPETITIVE RACING / FOR HOBBY-USE (SEPARATE ORDER FOR SPECIALIZED KTM WORKSHOP) COMPETITIVE RACING A 100 liter fuel consumption is equivalent to approx. 15 operating hours HOBBY-USE every 15 hours ...

  • KTM EXC-F 400 XC-W - page 27

    ENGLISH 26 ...

  • KTM EXC-F 400 XC-W - page 28

    MAINTENANCE WORK ON CHASSIS AND ENGINE » ENGLISH 27 A 3 1 2 Changing the spring preloading of the shock absorber The spring preload can be changed by turning the adjusting ring [1] . For this purpose, you should dismount the shock absorber and clean it thoroughly . NOTE: – Before changing the spring preload note down the basic setting, e.g. how ...

  • KTM EXC-F 400 XC-W - page 29

    MAINTENANCE WORK ON CHASSIS AND ENGINE » ENGLISH 28 A B B C 65 SPRING RA TE 70 75 80 85 90 95 RIDERS WEIGHT INCLUSIVE GEARS IN KILOGRAM 80/250 76/250 84/250 80/250 76/250 72/250 WP12187C06, WP12187C29 WP12187C04, WP12187C28 A B C Basic suspension setup for the weight of the driver T o achieve maximum handling performance and to prevent the fork, s ...

  • KTM EXC-F 400 XC-W - page 30

    MAINTENANCE WORK ON CHASSIS AND ENGINE » ENGLISH 29 Checking the basic setup of the telescopic fork The precise riding sag of the telescopic fork cannot be determined for various reasons. Similar to the shock absorber , smaller deviations in your weight can be compensated by adjusting the spring preload. However , if your telescopic fork bumps fre ...

  • KTM EXC-F 400 XC-W - page 31

    MAINTENANCE WORK ON CHASSIS AND ENGINE » ENGLISH 30 1 5 4 3 3 2 Breather plug front fork After every 5 hours of use for competitive racing, slacken the breather plugs [1] a few turns in order to relieve excess pressure from the inside of the fork. T o do this, place the motorcycle on a stand with the front wheel lifted off the ground. When riding ...

  • KTM EXC-F 400 XC-W - page 32

    MAINTENANCE WORK ON CHASSIS AND ENGINE » ENGLISH 31 B A 2 1 3 2 5 4 3 4 5 2 Changing the fork offset (caster) (XC, EXC SIXDAYS) * The fork offset [A] in these models (center fork legs - center steering head angle) can be set to either 18 or 20 mm. This allows you to optimize the han- dling to match the race course. Remove the blind screw [1] to se ...

  • KTM EXC-F 400 XC-W - page 33

    MAINTENANCE WORK ON CHASSIS AND ENGINE » ENGLISH 32 15 mm 3,5 mm 1 2 3 4 Mount the lower triple clamp, upper steering head bearing, protection ring, O-ring, upper triple clamp and the blind screw . T ighten the collar screw on the lower triple clamp to 60 Nm. Mount the fork legs and tighten the clamp screws on the lower triple clamp to 12 Nm in 3 ...

  • KTM EXC-F 400 XC-W - page 34

    MAINTENANCE WORK ON CHASSIS AND ENGINE » ENGLISH 33 8-10 mm / 0.3-0.4 in A 2 3 1 4 B 2 B 3 4 Check chain tension Jack the motorcycle up on its frame so that the rear wheel no longer touches the ground. Press the chain upward at the end of the chain sliding component. The distance between the chain and the swing arm should be approx. 8 - 10 mm (0.3 ...

  • KTM EXC-F 400 XC-W - page 35

    MAINTENANCE WORK ON CHASSIS AND ENGINE » ENGLISH 34 15 KG 33 lbs max. 272 mm 1 2 3 16 17 18 Chain maintenance For a long chain life, good maintenance is very important. Chains without X-rings should be cleaned in fireproof solvent regularly and afterwards treated with hot grease or chain spray (e.g. Motorex Chainlube 622). X-ring chains on the oth ...

  • KTM EXC-F 400 XC-W - page 36

    MAINTENANCE WORK ON CHASSIS AND ENGINE » ENGLISH 35 A 1 General information about KTM disc brakes BRAKE CALIPERS: The brake calipers of this series use a „floating“ mount. This means that the brake calipers are not solidly attached to the caliper support, which enables them to „float“ for maximum braking contact. Secure the screws of the c ...

  • KTM EXC-F 400 XC-W - page 37

    MAINTENANCE WORK ON CHASSIS AND ENGINE » ENGLISH 36 5 mm min. 3 mm 1 3 2 4 min. 1 mm Adjusting the free travel at the hand brake lever Free travel at the hand brake lever may be readjusted by using adjustment screw [1] . In this way , the position of the point of pressure (i.e. the resis-tance you feel on the hand brake lever when the brake pads a ...

  • KTM EXC-F 400 XC-W - page 38

    MAINTENANCE WORK ON CHASSIS AND ENGINE » ENGLISH 37 3-5mm 1 1 2 2 1 2 4 3 6 5 A B 7 Replacing the front brake pads * Press the brake caliper toward the brake disk, to put the brake piston in its basic position. Remove clips [1] and pull out bolt [2] . Remove brake pads from the brake caliper . Clean the brake caliper and the brake caliper support ...

  • KTM EXC-F 400 XC-W - page 39

    MAINTENANCE WORK ON CHASSIS AND ENGINE » ENGLISH 38 min. 1 mm 1 2 3 4 5 6 A B Checking the rear brake pads The brake pads can be inspected from the rear . The thickness of the linings may not be less than 1 mm (0.04 in). At their most worn point brake pad linings should not be thinner than 1 mm, otherwise they could lead to brake failure. For your ...

  • KTM EXC-F 400 XC-W - page 40

    MAINTENANCE WORK ON CHASSIS AND ENGINE » 3 ENGLISH 39 7 1 2 – If you don’t happen to have a torque wrench at hand, make sure you have the tightening torque corrected by a KTM dealer as soon as possible. A loose axle may lead to an unstable driving behavior of your motorcycle. – After mounting the front wheel, keep operating the hand brake un ...

  • KTM EXC-F 400 XC-W - page 41

    MAINTENANCE WORK ON CHASSIS AND ENGINE » ENGLISH 40 1 2 3 1 Tires, air pressure T ire type, tire condition, and air pressure level affect the way your motor -cycle rides and must therefore be checked whenever you are getting ready to go anywhere on your motorcycle. – T ire size can be found in the technical specifications and in the homolo- gati ...

  • KTM EXC-F 400 XC-W - page 42

    MAINTENANCE WORK ON CHASSIS AND ENGINE » ENGLISH 41 VOL T 2 3 1 Battery The battery is located under the seat and is maintenance-free. Maintenance-free means you will not need to check the acid level. Clean the battery terminals regularly and grease with acid-free grease if necessary . The charge condition and type of charge are very important for ...

  • KTM EXC-F 400 XC-W - page 43

    MAINTENANCE WORK ON CHASSIS AND ENGINE » ENGLISH 42 2 A 1 3 4 6 5 5 Fuse The fuse [1] is located in the starter relay of the E-starter [2] underneath the left side paneling. Having removed the left side paneling, the air box cover and the protection cover [A] , you will be able to see the fuse. The following loads are connected to it: – E-starte ...

  • KTM EXC-F 400 XC-W - page 44

    MAINTENANCE WORK ON CHASSIS AND ENGINE » ENGLISH 43 when engine is cold 10 mm 3 4 5 6 1 1 2 400/450/525 250-F Cooling system Coolant is circulated by a water pump [1] located in the engine. When the engine is cold the coolant only circulates through the cylinder and the cylin- der head. After the engine has reached its operating temperature (about ...

  • KTM EXC-F 400 XC-W - page 45

    MAINTENANCE WORK ON CHASSIS AND ENGINE » ENGLISH 44 XC EXC C 6 5 3 7 3 7 5 C 4 6 A B 2 1 EXC-F Replacing the glassfiber yarn packing of the silencer * Aluminum silencers are filled with glassfiber yarn to muffle noise. Have the filling checked regularly by an authorized KTM workshop (see Lubrication and Service Chart). The insulating material fibe ...

  • KTM EXC-F 400 XC-W - page 46

    MAINTENANCE WORK ON CHASSIS AND ENGINE » Adjusting the throttle cables * The throttle grip should always provide for a backlash of 3-5mm. Besides, with the engine running, the idling speed must not change if you turn the handlebar all the way to the left or right. T o adjust the throttle cables, dismount the seat and the tank together with spoiler ...

  • KTM EXC-F 400 XC-W - page 47

    MAINTENANCE WORK ON CHASSIS AND ENGINE » ENGLISH 46 1 2 4 3 6 5 7 Changing the original position of the clutch lever The adjusting screw [1] can be used for individual adjustment of the original position of the clutch lever , thus allowing adjustment to an optimal position for every hand size. T urning the adjusting screw counterclockwise reduces ...

  • KTM EXC-F 400 XC-W - page 48

    MAINTENANCE WORK ON CHASSIS AND ENGINE » ENGLISH 47 1 2 3 4 Carburetor – Adjust idling (Keihin-FCRMX 37/39/41) * Idling adjustment of the carburetor strongly affects the engine’ s starting behavior . That is, an engine whose idling speed is adjusted correctly will be easier to start than one whose idling speed has not been adjusted correctly . ...

  • KTM EXC-F 400 XC-W - page 49

    MAINTENANCE WORK ON CHASSIS AND ENGINE » ENGLISH 48 3 4 5 6 7 8 9 10 11 12 13 15 14 28 20 22 21 23 24 25 26 29 30 27 A B Draining the float chamber of the carburetor Following every wet cleaning procedure, the float chamber of the carburetor should be drained in order to remove any water that may have penetrated into it. W ater in the float chambe ...

  • KTM EXC-F 400 XC-W - page 50

    MAINTENANCE WORK ON CHASSIS AND ENGINE » ENGLISH 49 1 2 3 4 5 JASO T903 MA 5°C 41°F 0°C 32°F + – 10W/50 10W/50 5W/40 5W/40 250-F: 400/450/525: Engine oil Automobile engine oil used to be used for four -stroke motorcycles before there were separate motorcycle specifications. Different technical developments made it necessary to have a separat ...

  • KTM EXC-F 400 XC-W - page 51

    MAINTENANCE WORK ON CHASSIS AND ENGINE » ENGLISH 50 2 2 2 3 3 4 5 3 Changing the oil filters Place a receptacle underneath the engine to collect the drained oil. Remove the 4 screws [2] and dismount the two oil filter covers. Using circlip pliers, pull the oil-filter inserts [3] out of the housing. Clean the oil filter cover , the sealing surfaces ...

  • KTM EXC-F 400 XC-W - page 52

    TROUBLESHOOTING » ENGLISH 51 If you had the specified maintenance work on your motorcycle carried out, disturbances can hardly be expected. Should an error occur nevertheless, we advise you to use the troubleshooting chart in order to find the cause of error . W e would like to point out that many operations cannot be performed by yourself. In cas ...

  • KTM EXC-F 400 XC-W - page 53

    TROUBLESHOOTING » ENGLISH 52 TROUBLE CAUSE REMEDY Engine does not rev high Carburetor fuel level too high because float needle valve is dirty or worn out Loose carburetor jets Electronic ignition timing faulty Dismount carburetor and check if worn out T ighten jets Have ignition system checked Engine will not reach full power Fuel supply partially ...

  • KTM EXC-F 400 XC-W - page 54

    ENGLISH 53 CLEANING » Clean your motorcycle regularly in order to maintain the beauty of its plastic surfaces. The best manner would be to use warm water that has been mixed with a normal brand-name washing detergent and a sponge. The hard dirt can be removed before washing with the help of a soft water jet. If using a power washer , do not point ...

  • KTM EXC-F 400 XC-W - page 55

    TECHNICAL DATA – ENGINE » ENGLISH 54 JASO T903 MA 5°C 41°F + – 10W/50 5W/40 250-F: TEMPERA TUR ENGINE 250 XC-F 250 XCF-W, EXC-F Design Liquid-cooled single cylinder 4-stroke engine Displacement 249.51 ccm Bore/Stroke 76 / 55 mm Ratio 12.8 : 1 Fuel unleaded fuel with at least RON 95 (USA = Premium PON 91) V alve timing 4 valves controlled by ...

  • KTM EXC-F 400 XC-W - page 56

    TECHNICAL DATA – ENGINE » ENGLISH 55 BASIC CARBURATOR SETTING 250 XC-F USA 250 XCF-W USA 250 EXC-F 250 EXC-F SIXDAYS T ype Keihin FCR-MX 3900G Keihin FCR-MX 3900G Keihin FCR-MX 3900G Keihin FCR-MX 3900G Main jet 168 168 168 172 Jet needle OBETP OBEKT OBEKT OBETP Idling jet 40 40 40 40 Main air jet 200 200 200 200 Idling air jet 100 100 100 100 N ...

  • KTM EXC-F 400 XC-W - page 57

    TECHNICAL DATA – ENGINE » ENGLISH 56 ENGINE 400 XC-W, EXC 450 XC 450 XC-W, EXC 525 XC 525 XC-W, EXC Design Liquid-cooled single cylinder 4-stroke engine with balancer shaft Displacement 398 cc 449 cc 448 cc 510 cc Bore/Stroke 89 / 64 mm 95 / 63,4 mm 89 / 72 mm 95 / 72 mm Ratio 11 : 1 12 : 1 11 : 1 11 : 1 Fuel unleaded fuel with at least RON 95 ( ...

  • KTM EXC-F 400 XC-W - page 58

    TECHNICAL DATA – ENGINE » 57 ENGLISH 57 BASIC CARBURATOR SETTING 400 XC-W USA 400 EXC RACING EU T ype Keihin FCR-MX 3900D Keihin FCR-MX 3900E Main jet 178 178 Jet needle OBDVR OBDVR Idling jet 42 42 Main air jet 200 200 Idling air jet 100 100 Needle position 1st from top 1st from top Starting jet 85 85 Mixture control screw open 1.25 1.25 Slide ...

  • KTM EXC-F 400 XC-W - page 59

    TECHNICAL DATA – ENGINE » ENGLISH 58 TIGHTENING TORQUES – ENGINE 400/450/525 Hexagon collar screw , engine case, clutch cover , ignition cover M6 10 Nm Oil drain plug M12x1.5 20 Nm Allan head plug, oil screen short M16x1.5 Oil + 10 Nm Hexagon plug, oil screen long M20x1.5 15 Nm Collar screw for oil filter cover M5 6 Nm Plug pressure valve M12x ...

  • KTM EXC-F 400 XC-W - page 60

    TECHNICAL DATA – CHASSIS » ENGLISH 59 CHASSIS 250/400/450/525 Frame Central tube chrome-moly-steel frame Fork WP Suspension – 4860 MXMA / MXMA + P A Wheel travel front/rear 300/335 mm Rear suspension WP Suspension – 5018 PDS MCC / DCC, aluminium swing arm Front brake Disk brake with carbon-steel brake disc Ø 260 mm (10.2 in), brake caliper ...

  • KTM EXC-F 400 XC-W - page 61

    TECHNICAL DATA – CHASSIS » ENGLISH 60 STANDARD ADJUSTMENT – FORK 250 XCF-W 250 EXC-F 400/450/525 XC-W 400/450/525 EXC 525 XC DESERT RACING 250 XC-F 250 EXC-F SIXDAYS 450/525 XC 450/525 EXC SIXDAYS WP 4860 MXMA 14187C04 WP 4860 MXMA 14187C06 WP 4860 MXMA + P A 14187C28 WP 4860 MXMA + P A 14187C29 Compression adjuster 20 20 18 18 Rebound adjuste ...

  • KTM EXC-F 400 XC-W - page 62

    HEAD WORD INDEX » ENGLISH 61 Activating and deactivating display modes . . . . . . . . . . . . . .9 Adjusting the free travel at the hand brake lever . . . . . . . . .36 Adjusting the mixture control screw . . . . . . . . . . . . . . . . . .47 Adjusting the throttle cables . . . . . . . . . . . . . . . . . . . . . . .45 Basic information on carbur ...

  • KTM EXC-F 400 XC-W - page 63

    ENGLISH 62 ...

  • KTM EXC-F 400 XC-W - page 64

    ANHANG – APPENDICE APPENDIX – APÉNDICE 1 SCHALTPLAN » WIRING DIAGRAM 7 0 - 6 0 0 2 g n i c a R C X E m m a r g a i d g n i r i w s s e n r a h n i a m 0 5 1 . 5 7 0 . 1 1 . 4 9 5 6 0 0 2 . 4 0 . 8 0 h c t i w s r e h s a l f p u k c i p h c t i w s e k a r b r a e r r e h s a l f t n o r f t f e l r e h s a l f t n o r f t h g i r r e h s a l ...

  • KTM EXC-F 400 XC-W - page 65

    ANHANG – APPENDICE APPENDIX – APÉNDICE 2 SCHALTPLAN » WIRING DIAGRAM 7 0 - 5 0 0 2 W - C X , C X m m a r g a i d g n i r i w s s e n r a h n i a m 6 0 0 2 . 4 0 . 8 0 0 0 1 . 5 7 0 . 1 1 . 4 9 5 p u k c i p l i o c n o i t i n g i G 3 r o t a r e n e g rear light /brake light v r o s n e s d e e p s h c t i w s r a b e l d n a h ) l a n o i t ...

  • KTM EXC-F 400 XC-W - page 66

    ANHANG – APPENDICE APPENDIX – APÉNDICE 3 SCHALTPLAN » WIRING DIAGRAM ENGLISH DEUTSCH IT ALIANO Battery Batterie Batteria Cooling fan Lüftermotor Motorino ventola Driving light lamp Fernlichtkontrolle spia abbagliante Flasher control lamp Blinkerkontrolle spia lampeggiatori Flasher relay Blinkerrelais Relè indicatori Front brake switch vorde ...

  • KTM EXC-F 400 XC-W - page 67

    ANHANG – APPENDICE APPENDIX – APÉNDICE 4 SCHALTPLAN » WIRING DIAGRAM ENGLISH FRANCAIS ESP ANOL Battery Batterie Batería Cooling fan V entilateur Motor del ventilador Driving light lamp temoin feu route lampara aviso luces largas Flasher relay Relais de clignotants Relé de la luz intermitente Flasher control lamp temoin de clignoteur lampara ...

  • KTM EXC-F 400 XC-W - page 68

    KTM-Sportmotorcycle AG A–5230 Mattighofen www.ktm.at KTM Group Partner 5/2006 FOTO: MITTERBAUER 250 XC-F, XCF-W, EXC-F 400 XC-W, EXC RACING 450 XC, XC-W, EXC RACING 525 XC, XC-W, EXC RACING 525 XC DESERT RACING BEDIENUNGSANLEITUNG 2007 ART. NR. 3.211.145 DE DEUTSCH ...

Fabricant KTM Catégorie Motorcycle

Les documents que nous recevons du fabricant de l'appareilKTM EXC-F 400 XC-W peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques KTM
- manuels d’utilisations EXC-F 400 XC-W
- fiches produit KTM
- dépliants
- ou étiquettes-énergie KTM EXC-F 400 XC-W
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation KTM EXC-F 400 XC-W.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation KTM EXC-F 400 XC-W, manuels d’entretien, brefs manuels ou manuels de l’utilisateur KTM EXC-F 400 XC-W. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit KTM EXC-F 400 XC-W.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil KTM EXC-F 400 XC-W, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser KTM EXC-F 400 XC-W par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs KTM EXC-F 400 XC-W.

Le manuel d’utilisation complet KTM, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel KTM EXC-F 400 XC-W - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières KTM EXC-F 400 XC-W, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lKTM EXC-F 400 XC-W qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil KTM EXC-F 400 XC-W - qui devraient nous aider dans les premières étapes lors de l'utilisation KTM EXC-F 400 XC-W
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de KTM EXC-F 400 XC-W
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service KTM EXC-F 400 XC-W dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de KTM EXC-F 400 XC-W?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec KTM EXC-F 400 XC-W, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec KTM EXC-F 400 XC-W il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)