-
Chicago Electric 91511 - page 1
7” POR T ABLE WET TILE SA W Model 91511 ASSEMBL Y AND OPERA TING INSTR UCTIONS Distributed Exclusiv ely by Harbor F reight T ools 3491 Mission Oaks Blvd., Camarillo , CA 93011 Visit our W eb site at http://www .harborfreight.com Cop yr ight © 2004 b y Harbor F reight T ools ® . All rights reser ved. No por tion of this manual or any ar twork co ...
-
Chicago Electric 91511 - page 2
PR ODUCT SPECIFICA TIONS SA VE THIS MANU AL Y ou will need this manual f or the safety w ar nings and precautions , assembly , operating, inspection, maintenance and cleaning procedures, par ts list and assemb ly diagram. K eep your in voice with this manual. Wr ite the in v oice number on the inside of the front cov er . K eep this manual and inv ...
-
Chicago Electric 91511 - page 3
3. Keep b ystanders, children, and visitor s awa y while operating a power tool. Distractions can cause y ou to lose control. Protect others in the work area from debris such as chips and spar ks. Provide barriers or shields as needed. PERSONAL SAFETY 1. Stay alert. W atch what y ou are doing, and use common sense when operating a power tool. Do no ...
-
Chicago Electric 91511 - page 4
2. Do not use the power tool if the P ower Switc h does not turn it on or off. Any tool that cannot be controlled with the P ower Switch is dangerous and must be replaced. 3. Disconnect the P ower Cord Plug fr om the power sour ce before making an y adjustments, changing accessories, or storing the tool. Such prev entive saf ety measures reduce the ...
-
Chicago Electric 91511 - page 5
2. Double insulated tools are equipped with a polarized plug (one prong is wider than the other). This plug will fit in a polarized outlet only one wa y . If the plug does not fit fully in the outlet, rever se the plug. If it still does not fit, contact a qualified electrician to install a polarized outlet. Do not change the plug in any wa y . ...
-
Chicago Electric 91511 - page 6
resistance path to carr y electricity aw ay from the user , reducing the risk of electr ic shock. (See Figure A.) 2. The grounding prong in the plug is connected through the green wire inside the cord to the grounding system in the tool. The green wire in the cord must be the only wire connected to the tool’ s grounding system and must ne v er be ...
-
Chicago Electric 91511 - page 7
5. If you are using one e xtension cord f or more than one tool, add the nameplate amperes and use the sum to deter mine the required minimum cord siz e. (See Figure B.) 6. If you are using an e xtension cord outdoors, mak e sure it is marked with the suffix “W-A” (“W” in Canada) to indicate it is acceptab le for outdoor use . 7. Make sure ...
-
Chicago Electric 91511 - page 8
SPECIFIC SAFETY R ULES 1. Maintain labels and nameplates on the W et Tile Saw . These carr y impor tant inf or mation. If unreadable or missing, contact Harbor F reight T ools for a replacement. 2. D ANGER! Keep hands and fingers awa y from cutting area and Sa w Blade. Use a appropriate push stic k (not included) whene ver possib le. 3. Check Blad ...
-
Chicago Electric 91511 - page 9
13. Bef ore using the W et Tile Saw , make sure the Saw Blade is pr operly mounted on the Saw Spindle. Make sure the Sa w Blade is balanced, and is not crac ked or bent. 14. The Saw Blade will become hot while cutting. Allo w the Saw Blade to completely cool bef ore touching. 15. Allow the Sa w Blade to spin up to full speed before feeding a w orkp ...
-
Chicago Electric 91511 - page 10
SKU 91511 P A GE 10 25. W ARNING! People with pacemaker s should consult their ph ysician(s) before using this pr oduct. Electromagnetic fields in close proximity to a hear t pacemaker could cause interf erence to or f ailure of the pacemaker . 26. W ARNING! Some dust created by po wer sanding, sa wing, gr inding, drilling, and other constr uction ...
-
Chicago Electric 91511 - page 11
SKU 91511 P A GE 11 Saw Blade (6) from the Spindle of the Wet Tile Saw . Then, install a new diamond Saw Blade with a 7” diameter , 5/8” round arbor hole, and rated at a minimum 3,600 RPM. (See Figure D.) 6. NO TE: When installing the new Sa w Blade (6), make sure the directional arro w shown on the Sa w Blade is pointing toward the front of th ...
-
Chicago Electric 91511 - page 12
SKU 91511 P A GE 12 3. Check to mak e sure the Blade Guard (2) mov es freely upward and do wnward. (See Figure D .) 4. Close the Left Side Cutting T able (26). (See Figure D .) T o Attach The Fence And Miter Guide: 1. Place the F ence (11) on top of the Right Cutting T ab le (10) and clamp both ends of the F ence to secure it in place. The F ence i ...
-
Chicago Electric 91511 - page 13
SKU 91511 P A GE 13 3. Make sure the P ower Switch (21) is in its “OFF” position. Then, plug the P ower Cord (17) into the nearest 120 v olt, grounded, electrical outlet. (See Figure G.) T o P erform Straight Cutting: 1. Lift the front and rear Le v ers of the F ence (11). Slide the Fence along the T able to the left or right until the desired ...
-
Chicago Electric 91511 - page 14
SKU 91511 P A GE 14 FIGURE G WORKPIECE (NO T INCLUDED) FENCE (11) FENCE SCALE FENCE LEVER FENCE LEVER PO WER SWITCH (21) 2. Raise the Right Cutting T able (10) to the desired angle of cut (i.e ., 15°, 30°, 45°, or 60° ). (See Figure next page .) 3. Place the two Stands under neath the Right Cutting T able (10) into the groo ves to hold the Cutt ...
-
Chicago Electric 91511 - page 15
SKU 91511 P A GE 15 FIGURE H RIGHT CUTTING T ABLE (10) WORKPIECE (NO T INCLUDED) PO WER SWITCH (21) ST AND (0° to 60°) and tighten the Lock Knob to loc k the Miter Guide in place. (See Figure I.) 3. Place the workpiece flush against the Miter Guide (24). T ur n the P ower Switch (21) toits “ON” position, and allow the Sa w Blade (6) to spin ...
-
Chicago Electric 91511 - page 16
INSPECTION, MAINTENANCE, AND CLEANING 1. W ARNING! Alwa ys make sure the P ower Switc h (21) is in its “OFF” position, and unplug the P ower Cord (17) fr om its 120 volt electrical outlet before perf orming any inspection, adjustments, maintenance, or c leaning. 2. Before eac h use, inspect the general condition of the Wet Tile Saw . Check f or ...
-
Chicago Electric 91511 - page 17
P AR TS LIST SKU 91511 P A GE 17 P AR TS LIST SKU 91511 P A GE 17 Part # Description Qt y . Part # Description Qty. 1 Screw 1 18 Motor Bottom Base 1 2 Blade Guard 1 19 Electrical Cord Fixed Head 1 3 Wing Nut 1 20 Capacitor 1 4 Guard Support 1 21 Power Switch 1 5 Screw 1 22 Rubber Stand Screw 4 6 Continuous Rim Blade (7”) 1 23 Rubber Stand 4 7 Inn ...
-
Chicago Electric 91511 - page 18
SKU 91511 P A GE 18 LIMITED 1 YEAR / 90 DA Y W ARRANTY Harbor Freight T ools Co. makes every ef fort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that for a period of ninety days from date of purchase that the engine/motor , the belts (if so equipped), and the blades (if so equipped) ...
Avez-vous une question à propos de Chicago Electric 91511?
Utiliser le formulaire ci-dessous
Si vous n’avez pas résolu votre problème avec Chicago Electric 91511, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Chicago Electric 91511 il est probable qu’il a envie de partager la façon de le résoudre.