Français dropdown-ico

Manuel d’utilisation Avocent CCM4850

100 pages 0.99 mb
Télécharger

Aller à la page of 100

Summary
  • Avocent CCM4850 - page 1

    Installer/User Guide CCM4850 590-3 73-00 1B For T echnical Support: Equinox Systems One Equinox W ay Sunrise, Florida 3335 1 USA Tel: 954.7 46.9000 Email: support@equinox.com www.equinox.com ...

  • Avocent CCM4850 - page 2

    LIMITED WARR ANTY Equinox warrants t hat the Product(s ) shall be free from manufact uring defec ts in materials and workmanship for a period of ve ( 5) y ears from t he da t e of deliv ery provided t hat t he Product was properly installed and used. Defect s, malfunc tions or failures of t he warranted Produc t c aused by damage result ing from ...

  • Avocent CCM4850 - page 3

    CCM4850 Inst aller/User Guide A vocent, A VW orks and Equinox are re gistered trademarks of A vocent Corporation or its af filiates. All other marks are the property of their respective owners. © 2004 A vocent Corporation. All rights reserved. ...

  • Avocent CCM4850 - page 4

    USA Notification W ARNING: Changes or modifications to this unit not expressly appr oved by the party responsible for compliance could void the user ’ s authority to operate the equipment. NOTE: This equipment has been test ed and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limi ts are ...

  • Avocent CCM4850 - page 5

    iii Table of Contents List of Figures ................ ................... .................... ................... ................... ................... vii List of Tables ........... .................... ................... .................... ................... ................... ..... .. ix Chapter 1: Product Overview .. ......... ........ ...

  • Avocent CCM4850 - page 6

    iv CCM4850 Installer/User Guide Using Authenti cation Method s .................. ...................... .......................... ...................... ........... ..... . 23 Authentication summary ...... ......................... ....................... .............. ......................... ............ .. 24 Using security lock-out ........ ...

  • Avocent CCM4850 - page 7

    Table of Contents v Server Reboot command ................. ......................... .......................... ...................... .............. .. .5 3 Server Security command ..................... ......................... ......................... ....................... .......... .5 3 Server Set command ... .......................... ... ...

  • Avocent CCM4850 - page 8

    vi CCM4850 Installer/User Guide ...

  • Avocent CCM4850 - page 9

    vii List of Figures Figure 2.1: CCM4850 Appliance Front Panel ............................................................... ............ ....... 5 Figure 2.2: CCM4850 Appliance Back P anel ............. ................................................... ............ ....... 6 Figure B.1: CAT 5 and CAT 6 Cable Adaptor Pin Assi gnments .. ........ ...

  • Avocent CCM4850 - page 10

    viii CCM4 850 Installer/User Guide ...

  • Avocent CCM4850 - page 11

    ix List of Tables Table 2.1: LAN LED Values ............ ....................... .............. ......................... ....................... ..... ... ..... 5 Table 3.1: Default Port Settings .............. ......................... .......................... ......................... ..... ...... 11 Table 3.2: SSH Authentication Methods ..... ...

  • Avocent CCM4850 - page 12

    x CCM 4850 Installer/User Gu ide Table 5.17: Server SNMP Community Command Parameters................. ......................... .............. 55 Table 5.18: Server SNMP Manager Command Parame ters .............. ......................... .................... 56 Table 5.19: Server SNMP Trap Command Parameter ................. ..................... ...

  • Avocent CCM4850 - page 13

    1 CHAPTER 1 Product Overview Features and Benefit s Overview The CCM console management appliance provides non-blocked access and cont rol for serial devices such as serial-managed Linux (or other UNIX) servers, routers, power management devices and firewalls. Y ou may connect up t o 48 serial devices to a CC M4850 appliance. A single 10/100/1 000 ...

  • Avocent CCM4850 - page 14

    2 CCM 4850 Installer/User Gu ide Extensive command set The CCM appliance offers a wide range of commands that all ow administrators to easily configu re, control and display information abou t the CCM appliance operating environment, including its ports, user accounts and active s ession s. The serial CLI is always available on the unit’s console ...

  • Avocent CCM4850 - page 15

    Chapter 1: Product Overview 3 Using A VW orks Sof tware The AVWorks cross-platform management application may be used to manage CCM4850 appliances and access attached devices. Using AV Works software, you may perform most of the operations that are described in this manual. This manual describes how to manage a CCM4850 appliance by entering comm an ...

  • Avocent CCM4850 - page 16

    4 CCM 4850 Installer/User Gu ide ...

  • Avocent CCM4850 - page 17

    5 CHAPTER 2 Installation and Configuration Hardware Overview Figure 2.1 shows the front panel of a CCM4850 appliance. Figure 2.1: CCM4850 Appliance Fron t Panel The front panel contains the 48 serial port conn ectors. The lower left area of the front panel contains the following LEDs, buttons an d connectors: • The ONLINE LED illuminates steadily ...

  • Avocent CCM4850 - page 18

    6 CCM 4850 Installer/User Gu ide Figure 2.2 shows the back panel of a CCM4850 applian ce. Figure 2.2: CCM4850 Appliance Back Pan el The back panel contains: • The AC line cord connector . • On/off switch ( O = of f, | = on). • Outflow openings for the tw o internal fans. • A DB-9 DEBUG POR T connector . This port should be used only on the ...

  • Avocent CCM4850 - page 19

    Chapter 2: Installation and Configuration 7 3. Attach a 10BaseT , 100BaseT or 1000BaseT LAN interface cable to the LAN POR T connector on the back of the CCM appliance. A CA T 5 cable is required for 100BaseT operation. A CA T 6 cable is required for 1000BaseT operation. 4. Insert the power cord into the back of the unit . Insert the other end of t ...

  • Avocent CCM4850 - page 20

    8 CCM 4850 Installer/User Gu ide 3. Y ou may verify that the BootP process was successful with a ping command, which tests net- work connectivity . The ping command is entered as: ping <ip_address> For example, the following comm and tests th e network connectivity of a CCM ap pliance with the IP address 192.168.0.5. ping 192.168.0.5 4. If th ...

  • Avocent CCM4850 - page 21

    Chapter 2: Installation and Configuration 9 Initial CCM appliance login The CCM appliance ships with a single user defined in its user datab ase. The first time you connect to the CCM appliance, you ar e prompted for a username. T o log in to the CCM appliance for t he first time: 1. At the Username prom pt, type Admin . There is no factory defa ul ...

  • Avocent CCM4850 - page 22

    10 CCM4850 Installer/User Guide T o reinitialize the CCM appliance: 1. Locate the recessed INIT button on the front of the CCM applian ce. An opened paper clip may be used to depress the button. 2. Insert the end of the opened paper clip in th e recess, then depress and hold the button. The ONLINE LED will blink, indicati ng an initialization has b ...

  • Avocent CCM4850 - page 23

    11 CHAPTER 3 Operations Overview The CCM console management appliance and its po rts are easily configured and managed to meet your requirements for device co nnection, user authentication, access control, power status monitoring, port history informat ion display and Simple Network Management Protocol (SNMP) compliance for use with third party net ...

  • Avocent CCM4850 - page 24

    12 CCM4850 Installer/User Guide The Power parameter instructs the CCM appliance to monitor the state of a sp ecified control signal. Signal transitions may be confi gured to trigger SNMP traps. The parame ter value indicates an inbound control signal (CTS, DCD or DSR) and the state of that signal (low or high). When the defined signal is true, the ...

  • Avocent CCM4850 - page 25

    Chapter 3: Operations 13 A VWorks sof tware T elnet client Each CCM appliance is shipped with the AVWorks cross-platfo rm management application. AVWorks software provides a conv enient way to se lect a CCM appliance or an attached device and launch a Telnet session to manage it. AVWorks softwa re includes a built-in Serial Consol e Viewer Telnet a ...

  • Avocent CCM4850 - page 26

    14 CCM4850 Installer/User Guide port, you may also access devices thr ough a remote terminal or PC th at can dial into the external modem. For information about modem connections, see Configuring a nd using dial-in connections on page 14 and Server CLI command on pa ge 49. T o connect to a device from the console port : 1. Issue a Server CLI comman ...

  • Avocent CCM4850 - page 27

    Chapter 3: Operations 15 Connecting to d evices using PPP The CCM appliance supports remote PPP access usi ng an autoanswer modem that answers calls and establishes the PPP protocol with a dial-in client. Y ou may establish Telnet o r SSH connections over PPP. PPP dial-in may be used to access a remote CC M appliance that does not warrant a W AN (W ...

  • Avocent CCM4850 - page 28

    16 CCM4850 Installer/User Guide command includes the Encr ypt=SSH,None parameter, which in dicates that both SSH and plain text connections will be allowed. Connecting to Telnet port 23 may also be tunneled through a connection to SSH port 22. SSH server keys When SSH is enabled for the fi rst time, all sessions are t erm inated and the CCM applian ...

  • Avocent CCM4850 - page 29

    Chapter 3: Operations 17 A user’s access rights are determin ed from the authentication method used. SSH key authentication always uses the access rights from the local user database. Dependi ng on the server authentication mode specified w ith the Server Security command, SSH password authentication will use either the access rights from the loc ...

  • Avocent CCM4850 - page 30

    18 CCM4850 Installer/User Guide • When using the KEY keyw ord to specify the SSH key , the KEY parameter specifies the actual uuencoded SSH key . This is for configurations that do not implement an FTP server . The CCM appliance stores the specified key in the CCM user database. The CCM appliance processes a uuencoded SSH2 public key file with th ...

  • Avocent CCM4850 - page 31

    Chapter 3: Operations 19 T o enable both T elnet and SSH connections: Issue a Server Security comman d, indicating Encrypt=SSH,None. CLI mode While you are connected to an attached serial device, you may en ter Telnet CLI mode and enter CCM appliance commands. T o enter or exit CLI mode when connected to a ser ial device: 1. T o enter CLI mode, typ ...

  • Avocent CCM4850 - page 32

    20 CCM4850 Installer/User Guide DISCONNECT - or - Allow the port to tim e-out due to inactivity. In this case, a notification message is issued and the serial CLI session returns to CLI mode. This time-out may occur while you are in CLI mode. - or - For modem connections, if a carrier drop occurs, the serial CLI sessi on is au tomatically logged of ...

  • Avocent CCM4850 - page 33

    Chapter 3: Operations 21 T o add a user: Issue a User Add command. USER ADD < username > [PASSWORD=< pwd >] [SSHKEY=< keyfile >] [FTPIP=< ftpadd >] [KEY=< sshkey >] [ACCESS=< access >] You must specify a username. You must also specify a password or SSH user key information, or you may specify both. You may also ...

  • Avocent CCM4850 - page 34

    22 CCM4850 Installer/User Guide for each command are listed in Table 4.4 on page 36. Table 3.3 describes the access rights a user may be given . Access levels When you specify a user’s permissions, you may eith er indicate the individual rights as listed in Table 3.3 or you may indicate a predefined access level. The APPLIANCEADMIN and ADMIN leve ...

  • Avocent CCM4850 - page 35

    Chapter 3: Operations 23 USER ADD < username > ACCESS=< access > 2. T o change a user ’ s access rights/level, issue a User Set command, using the Access parameter to specify the rights or a level. USER SE T < username > ACCESS=< access > 3. T o display the access rights and level for one or all users, issue a Show User co ...

  • Avocent CCM4850 - page 36

    24 CCM4850 Installer/User Guide You may optionally specify both RADIUS and local au thenti cation, in either order. In this case, authentication w ill be attempted ini tially on the first metho d specified. If that fails, t he second method will be used for authenti cation. No authentication When authentication is di sabled, users are not auth enti ...

  • Avocent CCM4850 - page 37

    Chapter 3: Operations 25 You may also use this command to delete a RADIUS server definition. SERVER RADIUS PRIMARY |SECONDARY DELETE For more information, see Server RADIUS command on page 52. 2. Issue a Server Security comm and, using the Authentication pa rameter to specify the authenti- cation method. Use the Encrypt parame ter to en able plain ...

  • Avocent CCM4850 - page 38

    26 CCM4850 Installer/User Guide T o enable or disable security lock-out: 1. T o enable security lock-out, issue a Server Security comman d, using the Lockout parameter with a value between 1-99. 2. T o disable security lock-out, issue a Server Security command, us ing the Lockout=0 p a rameter . T o unlock a locked-out user: Issue a User Unlock com ...

  • Avocent CCM4850 - page 39

    Chapter 3: Operations 27 The following examples assume the user is in port history mode. The following command searches the history buff er in the upward dir ection for the string Abort Process. PORT HISTORY> s -u “Abort Process” The following command searches the history buffer for the string Process, ignoring case. PORT HISTORY> s -i Pr ...

  • Avocent CCM4850 - page 40

    28 CCM4850 Installer/User Guide SERVER CLI HISTORY=CLEAR|KEEP • If Clear is specified, the port history buffer is cleared and all data is discarded at the end of a session. • If Keep is specified, the port history buffer ’ s content is retain ed at the end of a session. T o clear and discard all dat a in a port history buff er: Issue a Clear ...

  • Avocent CCM4850 - page 41

    Chapter 3: Operations 29 NOTE: The default community names are “public”; if you enable SNMP , you are encouraged to change the community values to prevent access to the MIB. SERVER SNMP COMMUNITY READCOMM=< name > WRITECOMM=< name > TRAPCOMM=< name > Although all three comm unity names default to public, if you specify a trap ...

  • Avocent CCM4850 - page 42

    30 CCM4850 Installer/User Guide dash or a combination of numb ers with commas and dashes. To disable all traps, type ALL . To cancel the command, press Enter . - or - To disable all SNMP traps, issue a Server SNM P Trap command with the Disable and All parameters. In this case, the numbered list is not displayed. SERVER SNMP TRAP DISAB LE ALL For m ...

  • Avocent CCM4850 - page 43

    Chapter 3: Operations 31 T o display SNMP configuration information: Issue a Show Server SNMP command. SHOW SERVER SNMP The display includes information specified w ith the Server SNMP, Se rver SNMP Community , Server SNMP Manager, Server SNMP Trap a nd Server SNMP Trap Destination co mmands. For more information, see Show Server SNMP comm and on p ...

  • Avocent CCM4850 - page 44

    32 CCM4850 Installer/User Guide ...

  • Avocent CCM4850 - page 45

    33 CHAPTER 4 Using CCM Appliance Commands Accessing the CLI You may access the CLI in three ways: using the Telnet CLI, using the console port or entering the CLI access character during a sessi on to a serial device. When th e CLI is accessed, its prompt appears (>), indicating you may type a command. Entering Commands At the command prompt, ty ...

  • Avocent CCM4850 - page 46

    34 CCM4850 Installer/User Guide Table 4.2 lists the line editi ng operations for ASCII TTY devices. There is no command line buffer available on an ASCII TTY device. When commands take effect Each command is completely processed before the next command may be entered. Some commands prompt for confirmation b efore they are processed. In these cases, ...

  • Avocent CCM4850 - page 47

    Chapter 4: Using CCM Appliance Commands 35 Not every command will contain al l syntax types. For example, the following comm and reboots the CCM appliance. >SERVER REBOOT In this case, both SERVER and REBOOT are positional commands. In most cases, one or more spaces s eparate positional commands, posi tional parameters and keyword parame ters. F ...

  • Avocent CCM4850 - page 48

    36 CCM4850 Installer/User Guide In the following example, the keyword value “576 ” is not valid. Numeric keyword values must be fully specified and may not be shortened to three characters. > POR 2 SET BAUD=576 FLOW=XON --- ERR 27 - SET keyword value invalid In the following example, there are spaces betw een BAUD, the equal sign and the val ...

  • Avocent CCM4850 - page 49

    Chapter 4: Using CCM Appliance Commands 37 Port Alert Add Adds a port alert string. Access right: SCON or PCON Access level: ADMIN or APPLIANCEADMIN Port Alert Copy Copies a port’s alert strings to another port. Access right: SCON or PCON Access level: ADMIN or APPLIANCEADMIN Port Alert Delete Deletes one or more port alert strings. Access right: ...

  • Avocent CCM4850 - page 50

    38 CCM4850 Installer/User Guide Server RADIUS S pecifies RADIUS server parameters. Access right: SCON Access level: APPLIANCEADMIN Server Reboot Reboots the unit. Access right: SCON Access level: APPLIANCEADMIN Server Security S pecifies the user authentication mode, enables/disables secu rity lock-out and connection methods. Access right: SCON Acc ...

  • Avocent CCM4850 - page 51

    Chapter 4: Using CCM Appliance Commands 39 Show Server Displays CCM appliance configuration, statistics and session information. Access right: SMON Access level: ADMIN or APPLIANCEADMIN Show Server CLI Displays information specified wit h the Server CLI command. Access right: SMON Access level: ADMIN or APPLIANCEADMIN Show Server PPP Displays PPP s ...

  • Avocent CCM4850 - page 52

    40 CCM4850 Installer/User Guide User Unloc k Unlocks a locked-out user . Access right: USER Access level: ADMIN or APPLIANCEADMIN (An ADMIN level user may issue this command for users with any level other than APPLIANCEADMIN.) T able 4.4: CCM Appliance Command Summary (Continued) Command Description, Access Right and Access Level ...

  • Avocent CCM4850 - page 53

    41 CHAPTER 5 CCM Appliance Commands Connect Command The Connect command establishe s a connection from the CCM console management appliance console port to a device attached to another port on that CCM appliance. To use this command, yo u must have previously issued a Server CLI co mmand with the Connect=O n parameter. For more information, see Con ...

  • Avocent CCM4850 - page 54

    42 CCM4850 Installer/User Guide Help Command The Help command displays information about CCM appliance commands. Access right: none needed Access level: none needed Syntax HELP [< command_name >] Examples The following command displays inform ation about the Show Server CLI command. help sho ser cli The following command displays a list of al ...

  • Avocent CCM4850 - page 55

    Chapter 5: CCM Applianc e Commands 43 Port Alert Add command The Port Alert Add command adds a port alert string to a specified port. Each port m ay have up to ten port alert strings. Duplicate st rings are not allowed on the same port. To generate a trap, the Server SNMP Trap command must be issued to en able the PortAlert trap. For more informati ...

  • Avocent CCM4850 - page 56

    44 CCM4850 Installer/User Guide Port Alert Delete command The Port Alert Delete command deletes one or more alert strings from a port . When you issue this command, a numbered list of defi ned alert strings is displayed, from whic h you choose those to b e deleted. You may ent er one or more numbers sepa rated by commas, a range of numbers separate ...

  • Avocent CCM4850 - page 57

    Chapter 5: CCM Applianc e Commands 45 Access right: none needed Access level: all Syntax PORT HISTORY When you are in port history mod e, you may issue the commands listed in Table 3.5 on page 26. Examples The following command accesses the serial port’s history mode. > port history In history mode, the following command searches the hi story ...

  • Avocent CCM4850 - page 58

    46 CCM4850 Installer/User Guide T able 5.8: Port Set Command Parameters Parameter Description < port > A port number in the range 1-48, a range of port numbers separated by a dash, multiple port numbers separated by commas or CON. Default = port to which you are attached ALL Indicates that the port settings that follow should be applied to al ...

  • Avocent CCM4850 - page 59

    Chapter 5: CCM Applianc e Commands 47 Example The following command sets a baud rate of 57600 and enab les XON/XOFF flow control on port 2. > port 2 set baud=57600 flow=xonxof SOCKET=< socket > TCP port that must be entered on the T elnet client to connect to this serial port. The new value becomes effectiv e in subsequent sessions. When S ...

  • Avocent CCM4850 - page 60

    48 CCM4850 Installer/User Guide Quit Command The Quit command terminates the current CCM appliance session and terminates your Telnet connection to the unit. Access right: none needed Access level: all Syntax QUIT Resume Command The Resume command exits the CLI and resumes your connection to the attached serial device. The history buffer contains a ...

  • Avocent CCM4850 - page 61

    Chapter 5: CCM Applianc e Commands 49 Server CLI command The Server CLI command: • Specifies the co nsole port type • Specifies the CLI access character • Enables or disables device connection from the console port • Specifies a modem initialization string • Specifies po rt history mod e operations • Specifies a port time-out value At l ...

  • Avocent CCM4850 - page 62

    50 CCM4850 Installer/User Guide Server FLASH command The Server FLASH command updat es the CCM appliance program imag es in FLASH memory. Yo u may wish to use this command to update the program wi th new features or to install a later release. There are two program images that you may update in the CCM appliance FLASH. The boot image file (ccm50bt. ...

  • Avocent CCM4850 - page 63

    Chapter 5: CCM Applianc e Commands 51 Syntax SERVER FLASH BOOT|APP HOS TIP=< t ftp_add > IMAGE=< host_file > Example The following command updates the boot image program using the im age file name c:winntsystem32driversccm5 0bt.img, which is located on the TFTP serv er host located at 192.168.1.16. > ser fla app hostip=192.168.1. ...

  • Avocent CCM4850 - page 64

    52 CCM4850 Installer/User Guide Examples The following command enables the PP P server with a local IP address o f 192.168.0.1, a remote IP address of 192.168.0.2 an d a su bnet mask of 255.255.255.0. > ser ppp ena loc=192.168.0.1 rem=19 2.168.0.2 mas=255.255.255.0 The following command enables the PPP server with previously configured IP and su ...

  • Avocent CCM4850 - page 65

    Chapter 5: CCM Applianc e Commands 53 Examples The following command specifies pr imary RADIUS server information; default values wi ll be used for the UDP port, time-o u t and retries values. > ser radius primary ip=192.168.0.20 0 secret=ThePrimaryRadSecret user- rights=86 The following command deletes the primary RADIUS server defin ition. > ...

  • Avocent CCM4850 - page 66

    54 CCM4850 Installer/User Guide Syntax SERVER SECURITY [AUTHENTICATION=< aut h >] [ENCRYPT=< conns >] [LOCKOUT=< hours >] Server Set command The Server Set command changes CCM appliance address settings. You may specify one, two or all three parameters. A reboot is required if you change the IP address. Access right: SCON Access l ...

  • Avocent CCM4850 - page 67

    Chapter 5: CCM Applianc e Commands 55 Server SNMP command The Server SNMP command enables or disables SNMP UDP port 161 SNMP processing. When you disable SNMP processing, you may still enab le and disable traps w ith the Server SNMP Trap command. For more information, see Managing the CCM Applia nce Using SNMP on page 28. Access right: SCON Access ...

  • Avocent CCM4850 - page 68

    56 CCM4850 Installer/User Guide Server SNMP Manager command The Server SNMP Manager command defines or deletes SNMP management entities. You m ay define up to four managem ent en tities. If you delete all SNMP ma nagers (or never add any), the CCM appliance may be accessed using SNMP from any IP address. For more information, see Managing the CCM A ...

  • Avocent CCM4850 - page 69

    Chapter 5: CCM Applianc e Commands 57 Syntax SERVER SNMP TRAP [ ENABLE|DISABLE] [ALL] Example The following command enables the linkUp, userDeleted and userLogi n SNMP traps. server snmp trap enable Traps now disabled: 1) linkUp 4) userLogin 2) userAdded 5) imageUpgradeStarted 3) userDeleted Select trap(s) to enable>1,3-4 Server SNMP T rap Desti ...

  • Avocent CCM4850 - page 70

    58 CCM4850 Installer/User Guide terminated if a CCM SSH server key must be gene rated. Yo u must also h ave previously speci fied an authentication method other than No ne with the Server Security command. If you enable plain text Telnet connections with a Server Securi ty command, enab ling SSH session access with the Server SSH command will add t ...

  • Avocent CCM4850 - page 71

    Chapter 5: CCM Applianc e Commands 59 Show Port command The Show Port command displays configuratio n and status information about one or all ports. Access right: SMON Access level: ADMIN or APPLIANCEADMIN Syntax SHOW PORT [< port >|ALL|NAMES] The SHOW PORT NAME S co mmand displ ay includes the port nu mbers and names. If a port has not been ...

  • Avocent CCM4850 - page 72

    60 CCM4850 Installer/User Guide Show Port Alert command The Show Port Alert command displays a port’s alert strings. Access right: SMON Access level: ADMIN or APPLIANCEADMIN Syntax SHOW PORT < port > ALERT Show Server command The Show Server command displa ys CCM appliance configuration information and statistics. Access right: SMON Access ...

  • Avocent CCM4850 - page 73

    Chapter 5: CCM Applianc e Commands 61 Show Server CLI command The Show Server CLI command di splays the serial CLI settings. Access right: SMON Access level: ADMIN or APPLIANCEADMIN Syntax SHOW SERVER CLI T able 5.26: Show Server Command Display Fields Field Cont ent Server IP address (from initial configuratio n or Server Set command). Mask Subnet ...

  • Avocent CCM4850 - page 74

    62 CCM4850 Installer/User Guide Show Server PPP command The Show Server PPP comm and displays the current PPP settings that were configured with the Server PPP command. Access right: SMON Access level: ADMIN or APPLIANCEADMIN Syntax SHOW SERVER PPP Show Server RADIUS command The Show Server RADIUS comm and di splays the current CCM RADIU S settin g ...

  • Avocent CCM4850 - page 75

    Chapter 5: CCM Applianc e Commands 63 Show Server SNMP command The Show Server SNMP command displays SNMP configu ration information. Access right: SMON Access level: ADMIN or APPLIANCEADMIN Syntax SHOW SERVER SNMP Show User command The Show User command displays information about one or all users. Access right: SMON Access level: ADMIN or APPLIANC ...

  • Avocent CCM4850 - page 76

    64 CCM4850 Installer/User Guide A Show User All command display includes the information in Table 5.31. SPC Command The SPC command is reserved for future f unctionality. T able 5.30: Show User Command Display Fields Field Cont ents User Username. Level User ’s access level. If a level was not configured, access rights determine the level: Users ...

  • Avocent CCM4850 - page 77

    Chapter 5: CCM Applianc e Commands 65 User Commands The User command has several fo rms, as listed in Table 5.32. User Add command The User Add command adds a new user to the CCM user database. The user database holds a maximum of 64 user definitions. Fo r more information, see Managing User Accounts on page 20 and Access rights and levels on page ...

  • Avocent CCM4850 - page 78

    66 CCM4850 Installer/User Guide Examples The following command adds the username JohnD oe, with the p assword secretname, access to ports 2, 5, 6 and 7 and user and monitor access rights. > user add JohnDoe password=secretna me access=P2,5-7,user,smon The following command adds the username JaneDoe, with access to all ports. The name of the SSH ...

  • Avocent CCM4850 - page 79

    Chapter 5: CCM Applianc e Commands 67 User Logout command The User Logout command terminates a user’s active sessions on the C CM appliance. If the specified user has no active sessions, an error messa ge is displayed. For all active sessions that are terminated, a message is sent to the Telnet client and the Telnet connection is dropped. Access ...

  • Avocent CCM4850 - page 80

    68 CCM4850 Installer/User Guide Examples The following command sets the access rights fo r JohnDoe, enabling access to all ports with configuration and moni toring access rights. >user set JohnDoe access=pall,scon,s mon The following command removes th e server configuration access ri ght for JohnDoe, and leaves other access rights intact. > ...

  • Avocent CCM4850 - page 81

    Chapter 5: CCM Applianc e Commands 69 Syntax USER UNLOCK < username > T able 5.37: User Logout Command Param eter Parameter Description <username> Username to be unlocked. ...

  • Avocent CCM4850 - page 82

    70 CCM4850 Installer/User Guide ...

  • Avocent CCM4850 - page 83

    71 Appendices Appendix A: T echnical S pecifications T able A.1: CCM4850 Appliance T echnical Specifications Item V alu e Device Ports Number 48 T ype Serial ports Connectors Serial port RJ-45 Console Por t Number 1 Connector Serial port RJ-45 Network Connection Number 1 Ty p e Ethernet: IEEE 802.3, 10BaseT Fast Ethernet: IEEE 802.3U, 100BaseT Giga ...

  • Avocent CCM4850 - page 84

    72 CCM4850 Installer/User Guide AC-input cable 18 AWG thre e-wire cable, with a t h ree-lead IEC-320 recepta cle on the power supply end and a coun try depende nt plug on the powe r resource end Frequency 50 to 60 Hz T emperature 0 o to 55 o Celsius (32 o to 131 o Fahrenheit) operating -40 o to +70 o Celsius (-40 o to +158 o Fahrenheit) nonoper ati ...

  • Avocent CCM4850 - page 85

    Appendices 73 Appendix B: Device Cabling Each CCM appliance serial port has an R J-45 conn ector for attaching a se rial device. Table B.1 lists the pin assignments. Modular adaptors are available from Equinox to convert RJ-45 modular jacks to stand ard pinout configurations. Adaptors ar e available for use with: • CA T 5 and CA T 6 cable. • Se ...

  • Avocent CCM4850 - page 86

    74 CCM4850 Installer/User Guide Figure B.1 shows the pin assignments for the adaptors li sted in Table B.2. Figure B.1: CA T 5 and CA T 6 Cable Adaptor Pin A ssignments 210127 RJ-45 to RJ-45 Male Adaptor for Cisco and Sun Netra console port 750238 CA T 5 Serial St arter Kit - includes all t he above adaptors T able B.2: Adaptors for Use with CA T 5 ...

  • Avocent CCM4850 - page 87

    Appendices 75 Reversing adaptors and cables Table B.3 lists the reversing adaptors and reversing cables available from Equino x. T able B.3: Reversing Adaptors and Cables Part Number Description 210094 RJ-45 to DB-9M (DTE) Adaptor 210095 RJ-45 to DB-9F (DCE) Adaptor 210090 RJ-45 to DB-25M (DTE) Adaptor 210092 RJ-45 to DB-25M (DCE) Adaptor 210091 RJ ...

  • Avocent CCM4850 - page 88

    76 CCM4850 Installer/User Guide Figure B.2 shows the pin assignments for the adaptors li sted in Table B.3. Figure B.2: Reversing Cable Adapt or Pin Assignments If you choose to u se a non-Equinox reversing cable, make sure the cab le is reversing, as shown in Figure B.3. 8 7 6 5 4 3 2 1 RTS DSR CD RD TD GND DTR CTS 7 6 1 2 3 5 4 8 RTS DSR CD RD TD ...

  • Avocent CCM4850 - page 89

    Appendices 77 Figure B.3: 8-wire RJ-45 Reversing C able RTS DSR CD RD TD GND DTR CTS 1 2 3 4 5 6 7 8 8 7 6 5 4 3 2 1 RTS DSR CD RD TD GND DTR CTS 8-WIRE CCM Port Modular Adaptor ...

  • Avocent CCM4850 - page 90

    78 CCM4850 Installer/User Guide Appendix C: Supported T rap s The CCM appliance supports the following MIB2 traps: • authentication Failure • linkUp • linkDown •c o l d S t a r t Table C.1 lists the supported enterprise traps. The Equin ox web site, www.equinox.com, contains the complete tr ap MIB. T able C.1: CCM4850 Appliance Enterprise T ...

  • Avocent CCM4850 - page 91

    Appendices 79 UserAuthentication Failure A user failed to authenticate with the CCM appliance. V ariable: username FactoryDefaultsSet The CCM appliance has received a command to set itself to factory default values. (The appliance sends this trap after rece iving the command, but before actually reverting to fact ory default values.) PortAlert The ...

  • Avocent CCM4850 - page 92

    80 CCM4850 Installer/User Guide Appendix D: Port s Used Table D.1 lists the UDP and TCP port numbers us ed by the CCM appliance. The values assume a default configuration ; some values are configurable. T able D.1: Ports Used by CCM Appliance Port T ype and Number Used for TCP 22 SSH2, if enabled. TCP 23 T elnet. UDP 69 TFTP UDP 161 SNMP , if enabl ...

  • Avocent CCM4850 - page 93

    Appendices 81 Appendix E: T echnical Support Our Technical Support staff is ready to assist yo u wit h any installation or operating problems you encounter with your Equinox product. If an issue should devel op, follow the steps below for the fastest possible service: 1. Check the pertinent section of the manual to s ee if the issue may be resolved ...

  • Avocent CCM4850 - page 94

    82 CCM4850 Installer/User Guide ...

  • Avocent CCM4850 - page 95

    83 A Access rights and levels about 21 changing 22 configuring 22 displaying 22 Adaptors for use with CAT 5 and CAT 6 cable 73 reversin g 75 Authentication configuring 24 , 53 displaying configuration information 25 , 62 summary 24 types 23 See also RADIUS AVWorks software 1 , 3 , 7 B BootP 7 C Cabling 73 CLI accessing 33 changing the access charac ...

  • Avocent CCM4850 - page 96

    84 CCM4850 Installer/User Guide Show Server SNMP 63 Show User 63 summary 36 syntax 34 User Add 65 User command summary 65 User Delete 66 User Logout 67 User Set 67 User Unlock 68 Configuration IP address and subnet mask 7 serial port setting s 12 See also Port Connect command 41 Connection methods (Telnet and SSH) 18 Console port about connecting t ...

  • Avocent CCM4850 - page 97

    Index 85 IP address changing 54 configuring 7 displaying 60 L Line editing operations ASCII TTY devices 34 VT100 compatibl e devices 33 Lock-out. See Security lock-out Login 9 Logout 45 , 67 M Modem. See Dial-in connections Modular adaptors for use with CAT 5 and CAT 6 cable 73 reversin g 75 P Plain text connections 18 , 53 Port command summary 42 ...

  • Avocent CCM4850 - page 98

    86 CCM4850 Installer/User Guide Server SNMP Trap Destination comm and 57 Server SSH command 57 Session ending 19 , 45 , 48 , 67 preemption 20 time-out 20 , 45 , 49 , 61 Show command summary 58 Show Port Alert co mmand 60 Show Port command 59 Show Server CLI command 61 Show Server command 60 Show Server PPP command 62 Show Server RADIUS command 62 S ...

  • Avocent CCM4850 - page 99

    LIMITED WARR ANTY Equinox warrants t hat the Product(s ) shall be free from manufact uring defec ts in materials and workmanship for a period of ve ( 5) y ears from t he da t e of deliv ery provided t hat t he Product was properly installed and used. Defect s, malfunc tions or failures of t he warranted Produc t c aused by damage result ing from ...

  • Avocent CCM4850 - page 100

    Installer/User Guide CCM4850 590-3 73-00 1B For T echnical Support: Equinox Systems One Equinox W ay Sunrise, Florida 3335 1 USA Tel: 954.7 46.9000 Email: support@equinox.com www.equinox.com ...

Fabricant Avocent Catégorie Network Card

Les documents que nous recevons du fabricant de l'appareilAvocent CCM4850 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Avocent
- manuels d’utilisations CCM4850
- fiches produit Avocent
- dépliants
- ou étiquettes-énergie Avocent CCM4850
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Avocent CCM4850.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Avocent CCM4850, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Avocent CCM4850. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Avocent CCM4850.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Avocent CCM4850, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Avocent CCM4850 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Avocent CCM4850.

Le manuel d’utilisation complet Avocent, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Avocent CCM4850 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Avocent CCM4850, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lAvocent CCM4850 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Avocent CCM4850 - qui devraient nous aider dans les premières étapes lors de l'utilisation Avocent CCM4850
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Avocent CCM4850
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Avocent CCM4850 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Avocent CCM4850?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Avocent CCM4850, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Avocent CCM4850 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)