-
Toshiba IK-TF7C - page 1
For Customer Use Enter below the Serial No . which is located on the bottom of the cabinet. Retain this inf or mation f or future ref- erence. Model No.: IK-TF7C Serial No.: 3 CCD CAMERA IK-TF7C INSTR UCTION MANU AL FCC NOTICE This equipment has been tested and f ound to comply with the limits for a Class A digital de vice, pursu- ant to P ar t 15 ...
-
Toshiba IK-TF7C - page 2
2 SAFETY PRECAUTIONS Safety icons This manual contains safety instructions that must be observed in order to avoid potential hazards that could result in personal injuries, damage to your equipment, or loss of data. These safety cautions have been classified according to the seriousness of the risk, and the icons highlight these instructions as fol ...
-
Toshiba IK-TF7C - page 3
3 Disclaimer We disclaim an y responsibility and shall be held harmless for any damages or losses incurred b y the user in any of the f ollowing cases: 1. Fire, earthquake or any other act of God; acts by third par ties; misuse by the user , whether inten- tional or accidental; use under extreme operating conditions. 2. Malfunction or non-function ...
-
Toshiba IK-TF7C - page 4
4 1. CAUTIONS ON USE AND INST ALLA TION ..... 5 2. COMPONENTS ................................................ 5 3. ITEMS CONTROLLED BY USING ON SCREEN DISPLA Y .................................... 6 4. NAMES AND FUNCTIONS .............................. 7 5. CONNECTION .................................................. 8 5. 1 Standard Connection .. ...
-
Toshiba IK-TF7C - page 5
5 1. CAUTIONS ON USE AND INST ALLA TION • Carefully handle the units. Do not drop, or giv e a strong shock or vibration to the camera. This ma y cause problems . T reat the camera cables carefully to pre vent cab le problems, such as cable breakdown and loosened connec- tions. • Do not shoot intense light. If there is an intense light at a loca ...
-
Toshiba IK-TF7C - page 6
6 3. ITEMS CONTROLLED BY USING ON SCREEN DISPLA Y MODE E. TRG MANU speed Syncro. scan. Partial scanning T rigger (1P SNR/SR) T rigger (PW SNR/SR) 1P exposure time MODE MANU MODE Color temperature MANU AL R GAIN MANU AL B GAIN Master pedestal R pedestal B pedestal Shading correction mode Manual shading correction H phase adjustment Baud rate MANU , ...
-
Toshiba IK-TF7C - page 7
7 4. NAMES AND FUNCTIONS DISP PAGE DC IN 12V MENU DATA (AWB) 1 8 2 4 6 7 5 9 3 Prism faceplate DIGITAL terminal DISP button PAGE button [ Rear ] [ Front ] MENU UP button MENU DOWN button DATA UP (AWB) button DATA DOWN button DC IN 12V terminal 1 Prism faceplate The protection cap is attached on the lens mount por tion. After removing the cap, mount ...
-
Toshiba IK-TF7C - page 8
8 5. CONNECTION 5. 1 Standard Connection 5. 2 Cautions on Connection • When connecting the camer a cables, unplug the po wer source of the camera and the other equipment connected. • W e suggest using a C mount lens made for a 3CCD camer a. When using another lens, the best camera perf or mance of this camera may not be obtained. (For e xample, ...
-
Toshiba IK-TF7C - page 9
9 6. OPERA TION 1 Refer to the item " 5. CONNECTION", connect each equipment correctly . 2 T urn on the connected equipment and the power source of the camera. 3 P oint the lens at the object, operate the lens iris adjustment, focus adjustment, etc.. 4 Refer to the item "6.1 White Balance", operate the adjustment. 5 Refer to the ...
-
Toshiba IK-TF7C - page 10
10 2 MANU (Manual white balance) • Set the MODE to MANU on the WHT BAL menu. (Refer to the item "7.2 (3) WHT BAL (white balance)".) • Shoot a known white object, adjust the white balance adjusting the levels of R GAIN and B GAIN on the menu, confirming with a monitor or a monitor etc. (Refer to the item "7.2 (3) (3.2) Changing ea ...
-
Toshiba IK-TF7C - page 11
11 7. MODE SETTING BY ON SCREEN DISPLA Y V ar ious settings can be controlled on the unit by using the on screen men u display ed on the monitor . The contents once set are memorized ev en if the power source is turned off , so it is unnecessar y to set again when using the unit next time. When the setting is performed, select the menu of the item ...
-
Toshiba IK-TF7C - page 12
12 7. 2 Menus • Select the menu to change the setting by referring the item "7.1 Using the Menus".) • When the [MENU UP], [MENU DOWN] buttons are pushed, the " → " on the screen moves up and down. Move the " → " to the item to change. Note: When performing the mode setting in the menu display while selecting ON ...
-
Toshiba IK-TF7C - page 13
13 (1. 2) Changing each setting in SS (synchro. scan) mode (a) Changing the shutter speed setting 1 Set the " → " to SS by pushing [MENU UP], [MENU DO WN] buttons . 2 Select the shutter speed by pushing [D A T A UP], [DA T A DOWN] b uttons. (b) Partial scanning setting 1 Set the " → " to P ART by pushing [MENU UP], [MENU DO ...
-
Toshiba IK-TF7C - page 14
14 (1. 3) Changing each setting in E.TRG mode The E.TRG has five modes; 1P SNR, 1P SR, PW SNR, PW SR, RR. First set the " → " to MODE and select E. TRG, then set the " → " to E.TRG and select the desired E.TRG mode. (1. 3. 1) Changing each setting in 1P SNR mode (a) Changing the polarity of inputting trigger pulse setting 1 ...
-
Toshiba IK-TF7C - page 15
15 (1. 3. 2) Changing each setting in 1P SR mode (a) Changing the polarity of inputting trigger pulse setting 1 Set the " → " to TRG.P by pushing [MENU UP], [MENU DO WN] buttons. 2 Select either , by pushing [D A T A UP], [DA T A DOWN] buttons . (b) Changing 1P SR exposure time setting 1 Set the " → " to EXP . b y pushing [M ...
-
Toshiba IK-TF7C - page 16
16 (1. 3. 3) Changing each setting in PW SNR mode (a) Changing the polarity of inputting trigger pulse setting 1 Set the " → " to TRG.P by pushing [MENU UP], [MENU DO WN] buttons. 2 Select either , by pushing [D A T A UP], [DA T A DOWN] b uttons. (b) Changing the partial scanning setting 1 Set the " → " to P ART by pushing [ ...
-
Toshiba IK-TF7C - page 17
17 (1. 3. 4) Changing each setting in PW SR mode -- SHUTTER -- MODE E.TRG E.TRG PW SR TRG.P PART OFF <MODE = E.TRG E.TRG = PW SR> • Partial scanning switch OFF/60fps/90fps/E.60fps/E.90fps Input trigger pulse : positive polarity Input trigger pulse : negative polarity 1P SNR, 1P SR, PW SNR, PW SR, RR • Input trigger pulse setting at PW SNR ...
-
Toshiba IK-TF7C - page 18
18 (1. 3. 5) Changing each setting in RR mode (a) Changing the partial scanning setting 1 Set the " → " to P ART by pushing [MENU UP], [MENU DO WN] buttons. 2 Select either OFF/60fps/90fps/E.60fps/E.90fps by pushing [D A T A UP], [DA T A DOWN] b uttons. Note: The longer the storage time with extended exposures, the more visible certain ...
-
Toshiba IK-TF7C - page 19
19 ( 3 ) WHT BAL (White balance) WHT BAL has two modes; A WB, MANU . Set the " → " to MODE, push the [D A T A UP], [DA T A DOWN], and select mode among A WB, MANU. (3. 1) Changing each setting in AWB (Automatic White Balance) mode (a) Changing color temperature setting 1 Set the " → " to C.TEMP b y pushing [MENU UP], [MENU D ...
-
Toshiba IK-TF7C - page 20
20 ( 4 ) PROCESS (4. 1) Changing master pedestal 1 Set the " → " to M. PED by pushing [MENU UP], [MENU DO WN] buttons. 2 Set the master pedestal by pushing [D A T A UP], [DA T A DOWN] b uttons. (4. 2) Changing R pedestal 1 Set the " → " to R. PED by pushing [MENU UP], [MENU DOWN] b uttons. 2 Set the R pedestal by pushing [D ...
-
Toshiba IK-TF7C - page 21
21 ( 5 ) SYNC When an external sync signal is input, the display menu changes from INT (internal sync) to EXT (external sync) automatically . (5. 1) Adjusting horizontal phase 1 Set the " → " to H PHASE by pushing [MENU UP], [MENU DO WN] buttons . 2 Adjust the horizontal phase by pushing [D A T A UP], [DA T A DOWN] b uttons. ( 6 ) OPTIO ...
-
Toshiba IK-TF7C - page 22
22 7. 3 External Sync When using the unit with an e xter nal sync signal, input HD and VD to CC3 and CC4 of the DIGIT AL ter minal. When the external sync signal is input, the camera automatically switches its sync from the internal sync to the external sync. The operation is as shown belo w , depending on the unit's status and how e xternal s ...
-
Toshiba IK-TF7C - page 23
23 ( 3 ) Using the unit with external sync signal When adjusting H (horizontal) phase refer to the item "7.2 (5) (5.1) Adjusting horiz ontal phase". (3. 1) H (horizontal) phase adjustment Observe the external sync signal and the L V AL signal output wa vef or m of the unit with a dual trace oscilloscope, and ad- just H phase so that the H ...
-
Toshiba IK-TF7C - page 24
24 7. 5 EXT TRIG (External trigger) Charge begins to accumulate after the trigger input to CC1 of the DIGIT AL terminal, and 1 frame images are output. There are fiv e modes: 1P SNR, 1P SR, PW SNR, PW SR, RR. ( 1 ) 1P SNR (1 Pulse T rigger Sync Non Reset) Charge begins to accumulate after the trigger input to CC1 of the DIGIT AL terminal, and 1 fra ...
-
Toshiba IK-TF7C - page 25
25 About 1 µ s Exposure period* 2 Exposure period* 2 T rigger* 1 Negative polarity mode P ositive polarity mode RGB data (video interval image) (Internal VD) * 3 FV AL L V AL, DVA L 28H (P ar tial scanning OFF) 38H (P ar tial scanning 60fps) 47H (P ar tial scanning 90fps) ger , there will be an effect on the video. (1. 2) 1 Pulse T rigger SYNC-NON ...
-
Toshiba IK-TF7C - page 26
26 ( 2 ) 1P SR (1 Pulse T rigger Sync Reset) Charge begins to accumulate after the trigger input to CC1 of the DIGIT AL terminal, the ver tical sync signal is reset and frame images are output. (2. 1) 1 Pulse T rigger SYNC-RESET Picture Output Timing *1: Exter nally input signal *2: Exposure time is determined by the setting of "7. 2 (1.3) Cha ...
-
Toshiba IK-TF7C - page 27
27 ( 3 ) PW SNR (Pulse width trigger SYNC-NON RESET) The trigger input to CC1 of the DIGIT AL ter minal dev elops 1 frame images. (3. 1) Pulse Width T rigger SYNC-NON RESET Picture Output Timing (At Time of One-shot or Continuous External VD/Continuous External HD Input) *1: Exter nally input signal *2: Exposure time = T rigger pulse width + 6 µ s ...
-
Toshiba IK-TF7C - page 28
28 (3. 2) Pulse Width T rigger SYNC-NON RESET Picture Output Timing (at T ime of Internal Sync) *1: Exter nally input signal *2: Exposure time = T rigger pulse width + 6 µ s (V alid tr igger pulse width is 2 µ s or greater f or external trigger shutter operation.) *3: As long as there is no external sync input, the internal VD will be output when ...
-
Toshiba IK-TF7C - page 29
29 ( 4 ) PW SR (Pulse width trigger SYNC-RESET) The trigger input to CC1 of the DIGIT AL ter minal dev elops 1 frame images. (4. 1) 1 Pulse Width T rigger SYNC-RESET Picture Output Timing *1: Exter nally input signal *2: Exposure time = T rigger pulse width + 6 µ s (V alid tr igger pulse width is 2 µ s or greater f or external trigger shutter ope ...
-
Toshiba IK-TF7C - page 30
30 ( 5 ) RR (Reset restart) Input of an external reset-restart signal (CC4 of the DIGIT AL terminal: External VD input) permits one screen of information to be output at an arbitrary timing. (5. 1) Long T erm Exposure When a sufficient sensitivity is not obtained with the normal operating conditions or capturing the trail of a moving subject is des ...
-
Toshiba IK-TF7C - page 31
31 7. 6 Partial Scanning 1/29.2s (796H) Video interval image Blanking interval B Blanking interval D T otal A Video interval C RGB data (video interval image) (Internal VD) FV AL L V AL, DVA L Video period 1/60s (387H): When 60fps is selected 1/90s (258H): When 90fps is selected Video interval image ( 1 ) Partial Scanning OFF (All pixels scanning) ...
-
Toshiba IK-TF7C - page 32
32 8. INPUT OUTPUT SIGNAL SPECIFICA TOINS 2.0 µ s to 5.0 µ s (P ositive polarity mode) (Negative polarity mode) More than 2 µ s More than 2 µ s 5H to 21H ( 6 ) External HD/VD Input Phase Specifications 100 100 External HD rising edge Center Unit : Clock 1 clk=33.9nsec External HD The phase relationship of the external HD and VD should correspon ...
-
Toshiba IK-TF7C - page 33
33 9. CCD OUTPUT W A VEFORM TIMING CHART ( 1 ) Horizontal Output W aveform Timing Chart 246 clk 40 clk CLK=33.9 nsec (29.5 MHz) 164 clk 29 clk 3 clk 5 clk 33.9 ns L V AL, DVA L CCD output signal 5 clk Optical blac k por tion T otal effectiv e pixels 1034 clk Horizontal blanking interval 246 clk Optical blac k por tion Horizontal transf er stop inte ...
-
Toshiba IK-TF7C - page 34
34 10. SPECIFICA TIONS P ower supply P ower consumption Pick-up system Image sensor (Effectiv e pixels) Scanning system Scan frequency Sync system Horizontal resolution Sensitivity Minimum illumination Lens mount Ambient temperature Ambient humidity Weight External dimension White balance Gain Output signal Sync signal output External sync input In ...
-
Toshiba IK-TF7C - page 35
35 12. BEFORE MAKING A SER VICE CALL Symptom No image P oor color Items to be checked • Is the power supplied correctly? • Is the lens iris adjusted correctly? • Are the cables connected correctly? • Is the shutter mode set correctly? • Is the image process equipment set correctly? • Is the monitor adjusted correctly? • Is the white b ...
-
Toshiba IK-TF7C - page 36
LIMITED W ARRANTY TOSHIBA CCD CAMERA Promptly register your product with T oshiba on-line at www.toshiba.com/taisisd. By registering your prod- uct you will be eligib le for periodic updates, announcements, and special off ers. Y ou will hav e access to extended warranty options , upgrades (as applicable), useful tips , on-line troubleshooting, and ...
Avez-vous une question à propos de Toshiba IK-TF7C?
Utiliser le formulaire ci-dessous
Si vous n’avez pas résolu votre problème avec Toshiba IK-TF7C, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Toshiba IK-TF7C il est probable qu’il a envie de partager la façon de le résoudre.