Français dropdown-ico

Manuel d’utilisation Makita DCS232T

20 pages 1.1 mb
Télécharger

Aller à la page of 20

Summary
  • Makita DCS232T - page 1

    Instruction Manual Important: Read this instruction manual carefully bef ore putting the chain saw int o operation and strictly obser v e the saf ety regulations! Only persons who hav e completed training in working from ele vat ed platf orm s (cherr y pic k ers, lifts), f rom platforms mounted on ladders or who are pro ficient in climbing with rop ...

  • Makita DCS232T - page 2

    2 Thank y ou for pur cha sing a MAKIT A pr oduct! Congratulations on choosing a MAKIT A chain s a w! We are confident that you will be satisfied with this moder n piece of equipment. The DCS230T and DCS232T (T ophandle) are very light and handy chain saws with the handles on the top. These models were dev eloped espe- cially for tree surgery and ca ...

  • Makita DCS232T - page 3

    3 Symbols Y ou will not ice the f ollowing symbols on the chain saw and i n the instruction manual: Read instr uction manual and follow the warning- and safety precautions! I/ST OP -switch (shor t-circuit switch) Chain brak e War nin g This saw is to be used by properly trained operators only . Stop engine! Fuel and oil mix ture P articular care an ...

  • Makita DCS232T - page 4

    4 SAFETY PRECA UTIONS CA UTION: This chain saw is designed especially for tree care and surgery . All work with this chain saw is to be carried out by pr operly trained persons only . O bserve all literature, procedures and recommendations from the rel- evant pr ofessional organisation. Failure to do so constitutes a high acci dent risk! W e recomm ...

  • Makita DCS232T - page 5

    5 Before starting work the chain saw must be checked f or perfect function and operating safety accor ding to the prescri ptions. Check especially the function of the chain br ake, the correct mounting of the guide bar , the correct shar pening and tightening of the chain, the firm m ounting of the sprocket guard, the easy motion of the throttle le ...

  • Makita DCS232T - page 6

    6 - The saw must be running whenev er y ou remov e the chain saw f rom the wood. - When performing several cuts the throttle lev er mus t be released in between. - Be careful when cutting splintery wood. Cut pieces of wood ma y be pulled along (risk of injuries). - When cutting with the upper edge of the guide bar , the chain saw ma y be pushed in ...

  • Makita DCS232T - page 7

    7 Fir st aid For the e vent of a possible accident, please make sure that a first aid kit is always immediately av ailab le close by . Immediately replace any items used from the first aid box. When calli ng for help, give t he fo ll owing inf ormation: - Place of the accident - What happened - Number of injured people - Kind of injuries - Y our na ...

  • Makita DCS232T - page 8

    8 Denomination of compo nents 1 Rear handle 2 Safety l ocking b utton (throttle loc k) 3 Throttle le ver 4 Hand guard (releas e for chain brake) 5 Chain 6 Guide bar 7 Guide bar case 8 Retaining nuts 9 Chain catch (safety device) 10 Sp ro cke t c o ve r 11 Muf fler 12 Spark plug 13 F ront grip (tubular handle) 14 Star ter grip 15 I/ST OP-swi tch (s ...

  • Makita DCS232T - page 9

    9 P o sition the guide bar (7). Lift the chain (9) over the sproc ket (10). Usi ng y our right hand, guide the chain into the top guide groov e (11) on the guide bar . Note that the cut ting edges along th e top of the chain must point in the direction of the arrow ! Pull the chain (9) around the nose (12) of the guide bar in the direction of the a ...

  • Makita DCS232T - page 10

    10 Chain brake The DCS230T and DCS232T come with an inertia chain brake as standard equipment. If kick- back occurs due to contact of the guide-bar tip wit h wood (see “SAFETY PRECAUTIONS”), the chain brake will stop the chain th rough iner tia if the kickback is sufficiently str ong. The chain will stop within a fraction of a second. The chain ...

  • Makita DCS232T - page 11

    11 Chain oil Use an oil with adhesive additiv e for lubricating the chain and gu ide bar . The adhesiv e additiv e pre v ents the oil from being fl ung off the chain too quickly . W e recomm end the us e of chain oil which is bio-degradable in order to protect the en vironment. The use of bio-degr ad able oi l may e ven be required by local regulat ...

  • Makita DCS232T - page 12

    12 T o ensure troublefree operation of the oil pump the oil guide groov e at the housing ( 2) and the oil inlet bore in t he guide bar (3) must be cleaned regularly . Chec king the chai n lubricat ion Nev er work with the chain sa w without sufficient chain l ubrication. Otherwise the serv ice lif e of the chain and guide bar will be reduced. Befor ...

  • Makita DCS232T - page 13

    13 Chec king the c hain b rake Do not work with the c hain saw without first c hecking the c hain brake! Star t the engine as described (make sure you ha ve a good foot ing, and place the chain saw on t he ground in such a wa y that the guide bar is free of contact). Grasp the tub ular handle firmly with one hand and hold the grip with the other . ...

  • Makita DCS232T - page 14

    14 All cutters must be sharpened to the same angle, 30° . Diff erent angles result in a roughly , irregu- larly ru nning chain, increase wear and tear and cause chain beakage . The 85° front rake of the cu tter results from the cu t depth of the round file . If the proper file is used in the right manner , the correct front rake will be obtained ...

  • Makita DCS232T - page 15

    15 Cleaning the g uide bar , lubricating th e sproc ket nose CA UTION: Protective g loves m ust be worn . Regularly inspect the bearing surfaces of the guide bar f or damage, and clean them with a suitab le tool. Sprocket nose type: If the sa w is used intensiv ely it will be necessar y to lubricate the retur n sprocket bearings regularly (once a w ...

  • Makita DCS232T - page 16

    16 Electr ode gap The electrode gap must be 0.6 – 0.7 mm. Cleaning th e inlet p ort of the cooling air Unscrew f o ur screws (2). Remove recoil star ter (3). Clean the inlet por t (4) and the cylinder fins. Cleaning th e muffl er CA U TION: If the en gine is hot there is a risk of burning. Wear pr otective glo ves. Remove the sprock et cov er (se ...

  • Makita DCS232T - page 17

    17 Instructions for periodic main tenance T o ensure long lif e, prev ent damage and ensur e the full functioning of the safety f eatures the follo wing maintenance must be pe rformed regularly . Guaran- tee claims can be recognized only if this wor k is performed r egular ly and prope rly . F ailure to per form the prescr ibed maintenan ce work ca ...

  • Makita DCS232T - page 18

    18 Guaran tee MAKIT A guarantees the highest quality and will theref ore reimburse all costs for repair by repl acement of damaged par ts resulti ng from mater ial or pro- duction f aults occurring within the guarantee per iod after purchas e. Please note that in some countries par ticu lar guarantee co nditions may e xist. If you hav e an y questi ...

  • Makita DCS232T - page 19

    19 ...

  • Makita DCS232T - page 20

    Makita Corporation Anjo Aichi Japan 884570 A5 ...

Fabricant Makita Catégorie Chainsaw

Les documents que nous recevons du fabricant de l'appareilMakita DCS232T peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Makita
- manuels d’utilisations DCS232T
- fiches produit Makita
- dépliants
- ou étiquettes-énergie Makita DCS232T
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Makita DCS232T.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Makita DCS232T, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Makita DCS232T. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Makita DCS232T.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Makita DCS232T, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Makita DCS232T par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Makita DCS232T.

Le manuel d’utilisation complet Makita, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Makita DCS232T - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Makita DCS232T, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lMakita DCS232T qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Makita DCS232T - qui devraient nous aider dans les premières étapes lors de l'utilisation Makita DCS232T
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Makita DCS232T
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Makita DCS232T dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Makita DCS232T?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Makita DCS232T, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Makita DCS232T il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)