Français dropdown-ico

Manuel d’utilisation MTD 611

28 pages 3.68 mb
Télécharger

Aller à la page of 28

Summary
  • MTD 611 - page 1

    770-8751A IMPOR T ANT : READ SAFETY R ULES AND INSTR UCTIONS CAREFULL Y MTD PR ODUCTS INC. P .O . BO X 368022 CLEVELAND , OHIO 44136-9722 Sno w Thro wer Model 611 Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest- covered, brush-covered or grass-covered land unless the engine? ...

  • MTD 611 - page 2

    2 SECTION 1: IMPORTANT SAFE OPERATION PRACTICES WARNING: THIS SYMBOL POINTS OUT IMPORTANT SAFETY INSTRUCTIONS WHICH, IF NOT FOLLOWED, COULD ENDANGER THE PERSONAL SAFETY AND/OR PROPERTY OF YOURSELF AND OTHERS. READ AND FOLLOW ALL INSTRUCTIONS IN THIS MANUAL BEFORE ATTEMPTING TO OPERATE YOUR SNOW THROWER. FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY ...

  • MTD 611 - page 3

    3 • If the snow thrower should start to vibrate abnormally, stop the engine and check immediately for the cause. Vibration is generally a warning of trouble. • Stop engine whenever you leave the operating position, before unclogging the collector/impeller housing or discharge guide, and making any repairs, adjustments, or inspections. Never pla ...

  • MTD 611 - page 4

    4 SECTION 2: FINDING YOUR MODEL NUMBER This Operators Manual is an important part of your new snow thrower. It will help you assemble, prepare and maintain your snow thrower. Please read and understand what it says. Before you start to prepare your snow thrower for its first use, please locate the model plate and copy the information from it in thi ...

  • MTD 611 - page 5

    5 SECTION 4: CONTENTS OF HARDWARE PACK La y out the hardware according to the illustration f or identification pur poses. Part numbers are shown in parentheses. (Hardware pac k may contain e xtra items which are not used on y our unit.) A ATTACHING THE HANDLES (2)Hex Bolts (A) (710-3180) (4)Lock Washers (C) (736-0119) (2) Saddle (I) (784-5599) (2) ...

  • MTD 611 - page 6

    6 SECTION 5: ASSEMBLY INSTRUCTIONS IMPORTANT: After assembly, service engine with gasoline, and check oil level as instructed in the separate engine manual packed with your unit. NOTE: References to right or left side of the snow thrower are determined from behind the unit in the operating position. UNP A CKING • Remove staples or break glue on t ...

  • MTD 611 - page 7

    7 Figure 4 Figure 5 Figure 6 Figure 7 A TT ACHING THE HANDLES (Hardware A) 1. Place right handle in position against the snow thrower so the flat side of the handle is against the frame. Secure bottom hole in handle to snow thrower using hex bolt (B) and lock washer (C). There are weld nuts welded to the inside of the frame for these bolts. See Fig ...

  • MTD 611 - page 8

    8 Figure 8 Figure 9 Figure 10 A TT A CHING THE HANDLE P ANEL (Hardware C) Position the handle panel between handles. Insert carriage bolts (E) and secure with lock washers (C) and hex nuts (D). See Figure 8. A TT A CHING SPEED SELECT OR PLA TE AND SHIFT LEVER (Hardware D) 1. Assemble the speed selector plate to the outside of the handles as shown i ...

  • MTD 611 - page 9

    9 Figure 11 Figure 12 Figure 13 A TT A CHING THE CHUTE ASSEMBL Y (Hard ware F) 1. Place chute assembly over chute opening, with the opening in the chute assembly facing the front of the unit. Place chute flange keepers beneath lip of chute assembly, with the flat side of chute flange keeper facing downward. 2. Insert hex bolt (K) up through chute f ...

  • MTD 611 - page 10

    10 Figure 14 Figure 15 Figure 16 FINAL ASSEMBL Y AND ADJUSTMENTS A ug er Drive Clutch To check the adjustment of the auger drive clutch, push forward on the left hand clutch grip (depress the rubber bumper). There should be slack in the cable. Release the clutch grip. The cable should be straight. Make certain you can depress the auger drive clutch ...

  • MTD 611 - page 11

    11 TIRE PRESSURE (Pneumatic Tires) The tires are overinflated for shipping purposes. Check tire pressure and reduce to 15 to 20 psi. Refer to tire sidewalls for recommended tire pressure. NOTE: If the tire pressure is not equal in both tires, the unit may pull to one side or the other. SECTION 6: CONTROLS Figure 17 SHIFT LEVER (See Figure 17) The s ...

  • MTD 611 - page 12

    12 SECTION 7: OPERATION BEFORE ST ARTING WARNING: Observe all Warning Labels on the snow thrower prior to use. See Figure 1. Your snow thrower is shipped with oil; however, you must check the oil level before operating. Be careful not to overfill. The spark plug wire was disconnected for safety. Attach spark plug wire to spark plug before starting. ...

  • MTD 611 - page 13

    13 4. When engine starts, release starter button, and move choke gradually to OFF. If engine falters, move choke immediately to FULL and then gradually to OFF. Recoil Starter: 1. Rotate choke knob to FULL choke position (cold engine start). 2. If engine is warm, place choke in OFF position instead of FULL. 3. Push primer button two or three times f ...

  • MTD 611 - page 14

    14 SECTION 8: ADJUSTMENTS WARNING: NEVER attempt to clean chute or make any adjustments while engine is running. CHUTE ASSEMBL Y ADJUSTMENT The distance snow is thrown can be controlled by adjusting the angle of the top section of the chute assembly. SKID SHOE ADJUSTMENT The space between the shave plate and the ground can be adjusted. Refer to the ...

  • MTD 611 - page 15

    15 SECTION 9: LUBRICATION WARNING: Disconnect the spark plug wire and ground against the engine before performing any repairs or maintenance. ENGINE Refer to engine manual for engine lubrication instructions. WARNING: When following instruc- tions in separate engine manual for draining oil, be sure to protect frame to avoid oil dripping onto transm ...

  • MTD 611 - page 16

    16 • To remove skid shoes, remove the four carriage bolts, cupped washers and hex nuts which attach them to the snow thrower. Reassemble new skid shoes with the four carriage bolts, cupped washers (cupped side goes against skid shoes) and hex nuts. • To remove shave plate, remove the carriage bolts, cupped washers and hex nuts which attach it t ...

  • MTD 611 - page 17

    17 DRIVE BEL T 1. Follow steps 1 through 4 of previous instructions. 2. Pull idler pulley up, and lift belt off engine pulley and friction wheel disc. See Figure 26. 3. Using a 7/16" wrench, loosen the nut on the stop bolt until the support bracket rests on the auger pulley. See Figure 28. 4. Slip belt between friction wheel and friction wheel ...

  • MTD 611 - page 18

    18 SECTION 11: OFF-SEASON STORAGE WARNING: Never store engine with fuel in tank indoors or in poorly ventilated areas, where fuel fumes may reach an open flame, spark or pilot light as on a furnace, water heater, clothes dryer or other gas appliance. If unit is to be stored over 30 days, prepare for storage as follows: 1. Remove all gasoline from c ...

  • MTD 611 - page 19

    19 SECTION 12: Trouble Shooting Guide Note: For repairs beyond the minor adjustments above, contact your local authorized service dealer. T rouble P ossible Cause(s) Corrective Action Engine f ails to star t Fuel tank empty , or stale fuel. Block ed fuel line. Choke not in ON position F aulty spark plug. K ey not in switch on engine . Spark plug wi ...

  • MTD 611 - page 20

    20 Model 611 ...

  • MTD 611 - page 21

    21 Model 611 REF . NO . PA R T NO . DESCRIPTION QTY . REF . NO . PA R T NO . DESCRIPTION QTY . 2 05931 Housing, Bearing 1 27 736-0119 Lock W asher 9 3 618-0152 Gear Assembly (22") 1 28 736-0174 W asher, Flat 1 4 684-0052 22" Housing Assembly 1 29 736-0188 W asher, Flat, .76 I.D . x 5 684-0065 Impeller Assembly 1 1.49 O .D . x .06 6 6 605- ...

  • MTD 611 - page 22

    22 Model 611 ...

  • MTD 611 - page 23

    23 Model 611 REF . NO . PA R T NO . DESCRIPTION QTY . REF . NO . PA R T NO . DESCRIPTION QTY . 1 618-0063 Bearing Ass’y . 1 25 736-0242 W asher , Bell 1 2 656-0012A Ass’y ., F r iction Wheel Disc 1 26 712-0324 Nut 1 3 684-0013B Rod Shift, Wheel Dr ive 1 27 736-0351 Flat Washer 1 4 684-0021 Brkt. Ass’y . Friction Wheel 1 28 710-0809 Screw 1 5 ...

  • MTD 611 - page 24

    24 Model 611 * Not Shown - Fittings for Control Cable ** Not Shown REF . NO . PA R T NO . DESCRIPTION QTY . REF . NO . PA R T NO . DESCRIPTION QTY . 1 684-0022 Crank-Chute 1 22 736-0159 W asher 2 2 684-0047 Handle—L.H. 1 24 747-0904 Lev er-Shift 1 3 684-0048 Handle—R.H. 1 25 747-0905 Rod-Pivot 1 4 746-0778 Fitting for Cab le* 2 26 7103008 Screw ...

  • MTD 611 - page 25

    25 Model 611 †† Optional Kit † For Electric Start Option REF . NO PA R T NO . DESCRIPTION QTY . REF . NO PA R T NO . DESCRIPTION QTY . 1 05896A Brac ket-Idler 1 16 736-0329 Washer-Loc k 1 2 629-0071 Cord-Extension 110V† 1 17 736-0331 W asher-Lock 1 3 710-0627 Scre w-He x 1 18 736-0505 W asher-Flat 1 4 710-1245 Scre w-He x 1 19 736-0507 W as ...

  • MTD 611 - page 26

    26 NOTES ...

  • MTD 611 - page 27

    27 NOTES ...

  • MTD 611 - page 28

    28 MANUF A CTURER’S LIMITED W ARRANTY FOR: For TWO YEARS from the date of retail purchase within the United States of America, its possessions and territories, MTD PRODUCTS INC will, at its option, repair or replace, for the original purchaser, free of charge, any part or parts found to be defective in material or workmanship. This warranty cover ...

Fabricant MTD Catégorie Snow Blower

Les documents que nous recevons du fabricant de l'appareilMTD 611 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques MTD
- manuels d’utilisations 611
- fiches produit MTD
- dépliants
- ou étiquettes-énergie MTD 611
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation MTD 611.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation MTD 611, manuels d’entretien, brefs manuels ou manuels de l’utilisateur MTD 611. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit MTD 611.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil MTD 611, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser MTD 611 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs MTD 611.

Le manuel d’utilisation complet MTD, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel MTD 611 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières MTD 611, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lMTD 611 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil MTD 611 - qui devraient nous aider dans les premières étapes lors de l'utilisation MTD 611
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de MTD 611
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service MTD 611 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de MTD 611?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec MTD 611, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec MTD 611 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)