Français dropdown-ico

Manuel d’utilisation Yard Machines LT31CSH

24 pages 1.67 mb
Télécharger

Aller à la page of 24

Summary
  • Yard Machines LT31CSH - page 1

    Operator’ s Manual L T31CSH T rimmer / Brushcutter IMPORT ANT : READ SAFETY RULES AND INSTRUCTIONS CAREFULL Y P/N 769-01672A (7/05) ...

  • Yard Machines LT31CSH - page 2

    2 INTRODUCTION T ABLE OF CONTENTS Service Information . . . . . . . . . . . . . . . . . . . . . . . . .2 Rules for Safe Operation . . . . . . . . . . . . . . . . . . . . .3 Know Your Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 Assembly Instructions . . . . . . . . . . . . . . . . . . . . . . .8 Oil and Petrol Information . . . . . ...

  • Yard Machines LT31CSH - page 3

    3 RULES FOR SAFE OPERA TION READ ALL INSTRUCTIONS BEFORE OPERA TING • Read the instructions carefully. Be familiar with the controls and proper use of the unit. • Do not operate this unit when tired, ill, or under the influence of alcohol, drugs, or medication. • Children and teens under the age of 15 must not use the unit, except for teens g ...

  • Yard Machines LT31CSH - page 4

    4 • Add fuel in a clean, well-ventilated outdoor area where there are no sparks or flames. Remove the fuel cap slowly, and only after the engine stops. Do not smoke while fueling or mixing fuel. Wipe up any spilled fuel from the unit immediately. • Avoid creating a source of ignition for spilled fuel. Do not start the engine until fuel vapors d ...

  • Yard Machines LT31CSH - page 5

    5 • Do not run the unit at high speed when not cutting. • If you strike or become entangled with a foreign object, stop the engine immediately and check for damage. Have any damage repaired before attempting further operations. Do not operate unit with a bent, cracked or dull blade. Discard blades that are bent, warped, cracked or broken. • D ...

  • Yard Machines LT31CSH - page 6

    6 SAFETY AND INTERNA TIONAL SYMBOLS This operator's manual describes safety and international symbols and pictographs that may appear on this product. Read the operator's manual for complete safety, assembly, operating and maintenance and repair information. RULES FOR SAFE OPERA TION 12 3 SYMBOL MEANING • ON/OFF STOP CONTROL OFF or STOP ...

  • Yard Machines LT31CSH - page 7

    7 KNOW YOUR UNIT APPLICA TIONS As a trimmer: • Cutting grass and light weeds • Edging • Decorative trimming around trees, fences, etc. As a brushcutter: • Cutting weeds and light brush of up to 1/2 inch in diameter Primer Bulb Air Filter/Muffler Cover Spark Plug Muffler Blue Choke Lever Petrol Cap On/Off Stop Control Shaft Housing Starter R ...

  • Yard Machines LT31CSH - page 8

    8 ASSEMBL Y INSTRUCTIONS (4) Screws Top Clamp Middle Clamp Bottom Clamp Nuts Fig. 1 INST ALL AND ADJUST THE HANDLEBAR 1. Place the handlebar between the top and middle clamp pieces (Fig. 1). 2 . While holding the three pieces together, install the four (4) screws through the top clamp and into middle clamp. NOTE: The holes in the top and middle cla ...

  • Yard Machines LT31CSH - page 9

    9 ASSEMBL Y INSTRUCTIONS Install the cutting attachment shield when using the unit as a grass trimmer Install the cutting attachment shield on the shield mount by inserting the three (3) screws into the shield mount. Tighten securely with a flat blade screwdriver (Fig. 6). REMOVE THE CUTTING A TT ACH MENT AND INST ALL THE CUTTING BLADE NOTE: To mak ...

  • Yard Machines LT31CSH - page 10

    10 ASSEMBL Y INSTRUCTIONS Fig. 14 Fig. 11 Pilot Step REMOVE THE CUTTING BLADE AND INST ALL THE CUTTING A TT ACHMENT Remove the Cutting Blade 1. Align the shaft bushing hole with the locking rod slot and insert the locking rod into the bushing hole (Fig. 7). 2. Hold the locking rod in place by grasping it next to the boom of the unit (Fig. 13). 3. W ...

  • Yard Machines LT31CSH - page 11

    11 OIL AND PETROL INFORMA TION NOTE: Dispose of the old petrol/oil mix in accordance to Federal, State and Local regulations. OIL AND PETROL MIXING INSTRUCTIONS Old and/or improperly mixed fuel are the main reasons for the unit not running properly. Be sure to use fresh, clean unleaded petrol. Follow the instructions carefully for the proper petrol ...

  • Yard Machines LT31CSH - page 12

    12 ST ARTING/STOPPING INSTRUCTIONS Fig. 16 Starting Position Operate this unit only in a well- ventilated outdoor area. Carbon monoxide exhaust fumes can be lethal in a confined area. W ARNING: Avoid accidental starting. Make sure you are in the starting position when pulling the starter rope (Fig. 17). To avoid serious injury, the operator and uni ...

  • Yard Machines LT31CSH - page 13

    13 OPERA TING INSTRUCTIONS HOLDING THE TRIMMER Before operating the unit, stand in the operating position (Fig. 18). Check for the following: • The operator is wearing eye protection and proper clothing • The operator’s hands are firmly gripping the handles • The unit is at waist level • The cutting attachment is parallel to the ground an ...

  • Yard Machines LT31CSH - page 14

    14 OPERA TING INSTRUCTIONS Fig. 20 Fig. 21 Fig. 22 DECORA TIVE TRIMMING Decorative trimming is accomplished by removing all vegetation around trees, posts, fences and more. Rotate the whole unit so that the cutting attachment is at a 30° angle to the ground (Fig. 20). USING THE CUTTING BLADE Before operating the unit with the cutting blade, stand ...

  • Yard Machines LT31CSH - page 15

    15 MAINTENANCE AND REP AIR INSTRUCTIONS MAINTENANCE SCHEDULE Perform these required maintenance procedures at the frequency stated in the table. These procedures should also be a part of any seasonal tune-up. NOTE: Some maintenance procedures may require special tools or skills. If you are unsure about these procedures take your unit to any non-roa ...

  • Yard Machines LT31CSH - page 16

    16 MAINTENANCE AND REP AIR INSTRUCTIONS Fig. 27 Fig. 28 Fig. 30 Fig. 31 Fig. 26 NOTE: SplitLine™ can only be used with the inner reel with the slotted holes. Single line can be used on either type of inner reel. Use Figure 26 to identify the inner reel you have. NOTE: Always use the correct line length when installing trimming line on the unit. T ...

  • Yard Machines LT31CSH - page 17

    17 MAINTENANCE AND REP AIR INSTRUCTIONS INST ALLING A PREWOUND REEL 1. Hold the outer spool with one hand and unscrew the bump knob clockwise (Fig. 23). Inspect the bolt inside the bump knob to make sure it moves freely. Replace the bump knob if damaged. 2. Remove the old inner reel from the outer spool (Fig. 23). 3. Remove the spring from the old ...

  • Yard Machines LT31CSH - page 18

    18 MAINTENANCE AND REP AIR INSTRUCTIONS CARBURETOR ADJUSTMENT The idle speed of the engine is adjustable through the air filter/muffler cover (Fig. 38). NOTE: Careless adjustments can seriously damage your unit. An authorized service dealer should make carburetor adjustments. Check Fuel Mixture Old and/or improperly mixed fuel is usually the reason ...

  • Yard Machines LT31CSH - page 19

    19 MAINTENANCE AND REP AIR INSTRUCTIONS Clean Air Filter The condition of the air filter is important to the operation of the unit. A dirty air filter will restrict air flow and change the air/fuel mixture. This is often mistaken for an out of adjustment carburetor. Check the condition of the air filter before adjusting the idle speed screw. Refer ...

  • Yard Machines LT31CSH - page 20

    20 MAINTENANCE AND REP AIR INSTRUCTIONS CLEANING Use a small brush to clean off the outside of the unit. Do not use strong detergents. Household cleaners that contain aromatic oils such as pine and lemon, and solvents such as kerosene, can damage plastic housing or handle. Wipe off any moisture with a soft cloth. STORAGE • Never store a fueled un ...

  • Yard Machines LT31CSH - page 21

    21 TROUBLESHOOTING CAUSE ACTION Cutting attachment bound with grass Stop the engine and clean cutting attachment Cutting attachment out of line Refill with new line Inner reel bound up Replace the inner reel Cutting head dirty Clean inner reel and outer spool Line welded Disassemble, remove the welded section and rewind Line twisted when refilled D ...

  • Yard Machines LT31CSH - page 22

    22 SPECIFICA TIONS *All specifications are based on the latest product information available at the time of printing. We reserve the right to make changes at any time without notice. ENGINE* DRIVE SHAFT & CUTTING A TT ACHMENT* Engine Type............................................................................................................ ...

  • Yard Machines LT31CSH - page 23

    23 NOTES ...

  • Yard Machines LT31CSH - page 24

    24 NOTES ...

Fabricant Yard Machines Catégorie Brush Cutter

Les documents que nous recevons du fabricant de l'appareilYard Machines LT31CSH peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Yard Machines
- manuels d’utilisations LT31CSH
- fiches produit Yard Machines
- dépliants
- ou étiquettes-énergie Yard Machines LT31CSH
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Yard Machines LT31CSH.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Yard Machines LT31CSH, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Yard Machines LT31CSH. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Yard Machines LT31CSH.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Yard Machines LT31CSH, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Yard Machines LT31CSH par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Yard Machines LT31CSH.

Le manuel d’utilisation complet Yard Machines, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Yard Machines LT31CSH - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Yard Machines LT31CSH, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lYard Machines LT31CSH qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Yard Machines LT31CSH - qui devraient nous aider dans les premières étapes lors de l'utilisation Yard Machines LT31CSH
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Yard Machines LT31CSH
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Yard Machines LT31CSH dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Yard Machines LT31CSH?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Yard Machines LT31CSH, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Yard Machines LT31CSH il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)