-
Rose electronic MAN-V8 - page 1
10707 Stancliff Road Phone: (281) 933 - 7673 Houston, Texas 77099 WWW.ROSE.COM VISTA KVM - SERIES INSTALLATION AND OPERATIONS MANUAL ...
-
Rose electronic MAN-V8 - page 2
LIMITED WARRANTY Copyright Rose Electronics 1990 - 2001. All rights reserved. No part of this manual may be reproduced, stored in a retrieval system, or transcribed in any form or any means, electronic or mechanical, including photocopying and recording, without the prior written permission of Rose Electronics. Rose Electronics Part # MAN - V8 ...
-
Rose electronic MAN-V8 - page 3
FCC/IC STATEMENTS, EU DECLARATION OF CONFORMITY FEDERAL COMMUNICATIONS COMMISSION AND INDUSTRY CANADA RADIO - FREQUENCY INTERFERENCE STATEMENTS This equipme nt generates, uses and can radiate radio frequency energy and if not installed and used properly, that is in strict accordance with the manufacturer’s instructions may cause interference to r ...
-
Rose electronic MAN-V8 - page 4
TABLE OF CONTENTS Contents Disclaimer ................................................................................................ 1 Introduction .............................................................................................. 1 Product Registration ................................................................................ 2 ...
-
Rose electronic MAN-V8 - page 5
INTRODUCTION Vista KVM - Series Installation and Operations Manual 1 Disclaimer While every precaution has been taken in the preparation of t his manual, the manufacturer assumes no responsibility for errors or omissions. Neither does the manufacturer assume any liability for damages resulting from the use of the information contained herein. The m ...
-
Rose electronic MAN-V8 - page 6
2 Vista KVM - Series Installation and Operations Manual Product Registration Take advantage of the following when you register your Rose Electronics products online at www.rose.com/htm/warranty.htm : § Rose Standard War ranty Plus... § Free Lifetime Firmware Updates § Free Lifetime Technical Support § 30 Day Money Back Guarantee § Priority “ ...
-
Rose electronic MAN-V8 - page 7
Vista KVM - Series Installation and Operations Manual 3 Compatibility CPUs Computers Industry standard PCs, Unix computers such as RS - 6000, HP 9000, SGI, D EC Alpha, MAC and others Monitors SVGA Keyboards PC PS/2, AT, PC and Apple USB Mouse Standard PS/2 Mouse (2 or 3 button) PC and Apple USB Serial Mouse (2 or 3 button) KVM Station Monitors SVGA ...
-
Rose electronic MAN-V8 - page 8
OVER VIEW 4 Vista KVM - Series Installation and Operations Manual System overview The Vista KVM - series switch is designed to provide seamless, trouble - free switching from a single KVM station to any connected CPU. You can switch to the connected computers by simple keyboard commands or using the front panel buttons. Figure 1 shows a typical con ...
-
Rose electronic MAN-V8 - page 9
Vista KVM - Series Installation and Operations Manual 5 Figure 1 . Typical installati on Power connectors The optional power connector on the Vista switch is for a supplemental power adapter. Supplemental power may be needed if the cable length from the computers to the Vista switch is long or you are using a wireless keyboard and mouse. If your sy ...
-
Rose electronic MAN-V8 - page 10
MODELS 6 Vista KVM - Series Installation and Operations Manual Vista KVM - Series models Figure 2 . Vista 2 port Figure 3 . Vista 4 port Status LED Lit when selected CPU has power. Flashes when Keyboard and mouse data is sent to the unit Select LEDs Indicates which computer is selected Reset button Resets the unit and initializes the keyboard and m ...
-
Rose electronic MAN-V8 - page 11
Vista KVM - Series Installation and Operations Manual 7 KVM - 2UPH rear connectors KVM - 4UPH rear connectors Label Connector type Description (2UPH) 1,2 DB25F Computer connectors (4UPH) 1,2,3,4 DB25F Computer connectors Monitor HD15F KVM monitor connector Mouse MiniDin - 6F or DB9F KVM PS/2 or Serial mouse connector* Keyboard MiniDin - 6F or Din5F ...
-
Rose electronic MAN-V8 - page 12
8 Vista KVM - Series Installation and Operations Manual KVM - 2PCA rear connectors KVM - 4PCA rear connectors Label Connector Type Description Keyboard (MiniDin - 6F) Mouse (MiniDin - 6F) Video (HD15F) CPU connectors 1 - 2 on 2PC model 1 - 4 on 4PC model Monitor HD15F KVM monitor connector Mouse MiniDin - 6F or DB9F KVM PS/2 or Serial mouse connect ...
-
Rose electronic MAN-V8 - page 13
INSTALLATION Vista KVM - Series Installation and Operations Manual 9 Installation Installation of the Vista switch consists of the following steps: 1. Connect the KVM station to the Vista switch 2. Connect the CPUs to the Vista switch 3. Sequentially apply p ower, boot the CPUs 4. Verify keyboard, mouse and CPU operation It is recommended that the ...
-
Rose electronic MAN-V8 - page 14
10 Vista KVM - Series Installation and Operations Manual Step 2 - Connect the CPUs Connect the CPU keyboard, video monitor and mo use ports to the corresponding Vista switches keyboard, video monitor and mouse ports using the appropriate CPU cables as shown in Figure 5 . For attached CPUs that use a serial mouse, use adapter ACC - KVM6F9F to connec ...
-
Rose electronic MAN-V8 - page 15
Vista KVM - Series Installation and Operations Manual 11 Rack mounting The Vista switch is designed to mount in a CPU rack or under a desktop. Rackmount kits are available in three different sizes, 19", 23", and 24". Each is 1 rack unit high (1.75"). (See Appendix D and Appendix E for rack mounting instructions.) Your Vista swit ...
-
Rose electronic MAN-V8 - page 16
OPERATIONS 12 Vista KVM - Series Installation and Operations Manual Operating ins tructions The Vista switch is very easy to operate. Computer selection and set - up functions are entered from the keyboard. You can also select computers manually from the Vista’s front panel by using buttons 1 - 2 or buttons 1 - 4 depending on your model. Key boar ...
-
Rose electronic MAN-V8 - page 17
Vista KVM - Series Installation and Operations Manual 13 Keyboard commands (continued) Command Key Sequence Description Maximum computers <Ctrl> P x <Enter> (x = 1 – 2 or 1 – 4) Limits scanning t o maximum port number Typematic value <Ctrl> Ax <Enter> See Attachment F. Factory setting = 43 Rate = 10.9 chars/sec Delay = 5 ...
-
Rose electronic MAN-V8 - page 18
14 Vista KVM - Series Installation and Operations Manual Use only the numeric keys above the keyboard. The keypad will not work. All keyboard commands must be entered within 2 seconds of pressing and releasing the left <Ctrl> key. Keyboard command description Computer select To select a comput er from your keyboard, press and release the left ...
-
Rose electronic MAN-V8 - page 19
Vista KVM - Series Installation and Operations Manual 15 Reset To “Reset” the mouse and keyboard, press and release the left <Ctrl> key, then type “R”. This command is used to reset the mouse and keyboard on the currently selected Vista port without removing power from the Vista switch. This is most useful to reset a PS/2 mouse that h ...
-
Rose electronic MAN-V8 - page 20
16 Vista KVM - Series Installation and Operations Manual Maximum computers Press and release the left <Ctrl> key, type “P”, enter the total number of computers, and press <Enter>. This command limits the number of computers to scan. For example on an four - port unit, if no computers were connected to ports 3 and 4, setting maximum ...
-
Rose electronic MAN-V8 - page 21
FLASH UPGRADE PROCEDURE Vista KVM - Series Installation and Operations Manual 17 KVM Flash Upgrade Utility Installation of KVM Utility The installer for the KVM Utility ma y be distributed in one of two formats: a ZIP file or an EXE. If the installer is distributed as a ZIP file, open it in WinZip and unzip the contents to a known location. The ZIP ...
-
Rose electronic MAN-V8 - page 22
18 Vista KVM - Series Installation and Operations Manual 1. Download the flash upgrade firmwa re and unzip it to an .EXE file 2. Down load to a computer connected to port #1. 3. Run the unzipped “EXE” file . P rogram will auto - detect the unit 4. Click on " File", then "Load New Firmware" 5. Locate the downloaded unzipped f ...
-
Rose electronic MAN-V8 - page 23
Vista KVM - Series Installation and Operations Manual 19 8. When the firmware has been successfully installed the unit is now operat ional with the firmware upgrade. A more comprehensive explanation of the firmware upgrade process can be viewed by clicking on "Help". The on - line help walks you through each step in detail ...
-
Rose electronic MAN-V8 - page 24
TROUBLESHOOTING 20 Vista KVM - Series Installation and Operations Manual TroubleShooting CPU does not boot, keyboard or mouse error receiv ed • Cable is loose, reseat cable and hit F1 to continue or reboot computer. • Wrong cable plugged in, keyboard and mouse cables reversed. • Cable is defective; try using a cable from another CPU. If the p ...
-
Rose electronic MAN-V8 - page 25
Vista KVM - Series Installation and Operations Manual 21 Video fuzzy • Cable too long or wrong type. Use coax cable for high resolution. Mouse does not move • The Vista is turned off after or not connected when CPU was booted or the application using th e mouse was run. Exit and re - enter application or operating system using mouse or issue re ...
-
Rose electronic MAN-V8 - page 26
SERVICE 22 Vista KVM - Series Installation and Operations Manual Mainten ance and repair This unit does not contain any internal user - serviceable parts. In the event a unit needs repair or maintenance, you must first obtain a Return Authorization (RA) number from Rose Electronics or an authorized repai r center. This Return Authorization number m ...
-
Rose electronic MAN-V8 - page 27
SAF ETY Vista KVM - Series Installation and Operations Manual 23 Safety This Vista switch has been tested for co nformance to safety regulations and requirements, and has been certified for international use. Like all electronic equipment, the Vista switch should be used with care. To protect yourself from possible injury and to minimize the risk o ...
-
Rose electronic MAN-V8 - page 28
24 Vista KVM - Series Installation and Operations Manual Safety and EMC regulatory statements Safety Information Do cumentation reference symbol. If the product is marked with this symbol, refer to the product documentation to get more information about the product. WARNING A WARNING in the manual denotes a hazard that can cause injury or death. CA ...
-
Rose electronic MAN-V8 - page 29
Vista KVM - Series Installation and Operations Manual 25 Safety and EMC regulatory statements Informations concernant la sécurité Symbole de référence à la documentation. Si le produit est marqué de ce symbole, reportez - vous à la documentation du produit afin d’obtenir des informations pl us détaillées. WARNING Dans la documentation, u ...
-
Rose electronic MAN-V8 - page 30
APPENDICES 26 Vista KVM - Series Installation and Operations Manual Appendix A. Initial factory settings Setting Default Value Foreground Color White Background Color Blue X - position 45 Y - position 90 Fadeout Time 20 seconds Font 8 x 16 modern Screen Saver Fireflies Screen Saver Time 10 minutes M aximum Ports 2 or 4 Scan enable Off Scan Time Int ...
-
Rose electronic MAN-V8 - page 31
Vista KVM - Series Installation and Operations Manual 27 Appendix B. Parts and cables Vista Part Numbers Description KVM - 2 /4 PCA 2 /4 - port w/PC connectors KVM - 2 / 4 UPH 2 /4 - port w/DB25 connectors KVM - 2UPMH 2 - port (1 - PC, 1 - MAC) DB25 connectors KVM - 4UPMH 4 - port (2 - PC, 2 - MAC) DB25 connectors Note: KVM2UPMH has CPU port 2 pre ...
-
Rose electronic MAN-V8 - page 32
28 Vista KVM - Series Installation and Operations Manual Rackmount Kits RM - UM19 Black anodized, for installation in 19" racks. RM - UM23 Black anodized, for installation in 23" racks. RM - UM24 Black anodized, for installation in 24" racks. Rm - UD - 1U Under desk mounting kit Appendix C. General specifications Size 13.2" W x ...
-
Rose electronic MAN-V8 - page 33
Vista KVM - Series Installation and Operations Manual 29 Appendix D. Rack mount instructions The optional rack mount kit includes the following items: § Two black anodized mounting bracke ts. § Four 6 - 32 x 3/8” flat head mounting screws. To rack mount your Vista switch, attach the two rack mounting brackets to your unit with the short flange ...
-
Rose electronic MAN-V8 - page 34
30 Vista KVM - Series Installation and Operations Manual Appendix F. Typematic rate Ty pematic Command Press the left <Ctrl> key, type “A”, enter the typematic value (1 - 3 digit) followed by <Enter>. The typematic value is determined from the following tables using the equation: Typematic Value = Rate value + Delay Value. Pick the ...
-
Rose electronic MAN-V8 - page 35
...
-
Rose electronic MAN-V8 - page 36
10707 Stancliff Road Phone: (281) 933 - 7673 Houston, Texas 77099 WWW.ROSE.COM ...
Avez-vous une question à propos de Rose electronic MAN-V8?
Utiliser le formulaire ci-dessous
Si vous n’avez pas résolu votre problème avec Rose electronic MAN-V8, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Rose electronic MAN-V8 il est probable qu’il a envie de partager la façon de le résoudre.