Français dropdown-ico

Manuel d’utilisation TANDBERG D1320203

39 pages 0.25 mb
Télécharger

Aller à la page of 39

Summary
  • TANDBERG D1320203 - page 1

    TANDBERG 3G Gateway Data port Command In terface User Guide T ANDBERG 3G Gateway Data port Command Interface User Guide Softwar e version R 3 D1320203 TANDBERG D1320203 1 ...

  • TANDBERG D1320203 - page 2

    TANDBERG 3G Gateway Data port Command In terface User Guide Table of Contents 1. INTRODUCTION ...........................................................................................................................3 2. CONNECTIN G TO THE DATA PORT COM MAND INTERFACE THROUGH THE RS -232 PORT. 4 2.1. H ARDWARE AND C ABLING ........................ ...

  • TANDBERG D1320203 - page 3

    TANDBERG 3G Gateway Data port Command In terface User Guide 1. Introduction The TANDBERG 3G Gateway Data port Command Interface User Guide contains guidelines on how to us e the textual command interface supported by the 3G Gateway system, further referred to as 3G Gateway . The Data port Command Interface can be accessed through Te lnet via the LA ...

  • TANDBERG D1320203 - page 4

    TANDBERG 3G Gateway Data port Command In terface User Guide 2. Connecting to the Data port Command Interface through the RS-232 port. The RS-232 port is a 9-pin, fem ale, sub-D connector located on the front of the 3G Gateway. The port is configured as a DCE (Data Communications Equipment). The RS-2 32 port is default set to 115200 baud, 8 data bit ...

  • TANDBERG D1320203 - page 5

    TANDBERG 3G Gateway Data port Command In terface User Guide D1320203 5 If communication cannot be established between the PC /terminal and the TANDBERG 3G Gateway’s Data port the following should be checked: • Verify that the serial cable is a straight through 9-pin to 9-pin cable • Confirm that the configuration of the PC/terminal’s serial ...

  • TANDBERG D1320203 - page 6

    TANDBERG 3G Gateway Data port Command In terface User Guide 3. Connecting to the Data port Co mmand Interface using Telnet The TANDBERG 3G Gateway has one LAN port. The 3G Gateway’s Telnet server provides access to the Data port Co mmand Interface through a 10/100 base T network interface supporting the TCP/IP protocol. When connected to the 3G G ...

  • TANDBERG D1320203 - page 7

    TANDBERG 3G Gateway Data port Command In terface User Guide 4. The TANDBERG 3G Gateway Commands 4.1. Introduction Typing ‘ ? ’ or ‘ help ’ when connected to the Data Port Comma nd Interface will return a list of valid commands. The commands are used to control the functions of the 3G Gateway. A command may be followed by a set of parameters ...

  • TANDBERG D1320203 - page 8

    TANDBERG 3G Gateway Data port Command In terface User Guide 4.1.2. Command types The commands can be divided into three major classes: • Parameter Configuration Commands, Xconf. • Status Commands, Xstat. • User Commands, Xcom. Parameter Configuration Commands are commands that set a system parameter to a specific value. E.g.: The command Xcon ...

  • TANDBERG D1320203 - page 9

    TANDBERG 3G Gateway Data port Command In terface User Guide 4.2.1. System Configuration Commands Command: Description: Dialplan Mapping o f a call onto a se rvice or anot her call. Dialplan En try [1.. 64] Enable d: <On/Off> Dialplan Entry [1..64 ] Na m e: <S: 0, 30> Dialplan Entry [1 ..64] NetType: <All/H324m/H323/SIP> Dialplan E ...

  • TANDBERG D1320203 - page 10

    TANDBERG 3G Gateway Data port Command In terface User Guide distingui shed: • Net type - Either H324m, H323 or SIP of the outbound call. • AV mode – Th is mode deter mines the out bound audi o and vide o call settings. It is either Audio Only , Audio + Vi deo, Aut o(matic) no fallback to au dio, Auto + fallback to audi o and Auto + always fal ...

  • TANDBERG D1320203 - page 11

    TANDBERG 3G Gateway Data port Command In terface User Guide *c xConfigurat ion Dialpla n Ent ry 1 Prefi x: "207947 13 3" *c xConfigurat ion Dialpl a n Entry 1 Suffix: " " *c xConfigurat ion Dialpl a n Entry 1 Service Id: 1 *c xConfigurat ion Dialpla n Ent ry 1 Pro pe rt y 1 Nam e: "nettype" *c xConfigurat ion Dialpla n ...

  • TANDBERG D1320203 - page 12

    TANDBERG 3G Gateway Data port Command In terface User Guide *c xConfigurat ion Dialpla n Ent ry 2 Pro pe rt y 2 Nam e: "avmode" *c xConfigurat ion Dialpla n Ent ry 2 Pro pe rt y 2 Value: " 4" *c xConfigurat ion Dialpla n Ent ry 2 Pro perty 3 Name : "prefi x" *c xConfigurat ion Dialpla n Ent ry 2 Pro pe rt y 3 Value: &q ...

  • TANDBERG D1320203 - page 13

    TANDBERG 3G Gateway Data port Command In terface User Guide *c xConfigurat ion Dialpla n Ent ry 4 Prefi x: "903700 10" *c xConfigurat ion Dialpl a n Entry 4 Suffix: " " *c xConfigurat ion Dialpl a n Entry 4 Service Id: 3 *c xConfigurat ion Dialpla n Ent ry 4 Pro pe rt y 1 Nam e: "allowredirectep" *c xConfigurat ion Dia ...

  • TANDBERG D1320203 - page 14

    TANDBERG 3G Gateway Data port Command In terface User Guide *c xConfigurat ion Dialpla n Ent ry 4 Pro perty 14 Nam e : "entry5 _la bel " *c xConfigurat ion Dialpla n Ent ry 4 Pro pe rt y 14 Val ue: "M enu" *c xConfigurat ion Dialpla n Ent ry 4 Pro pe rt y 15 Nam e: "entry5_netty pe" *c xConfigurat ion Dialpla n Ent ry ...

  • TANDBERG D1320203 - page 15

    TANDBERG 3G Gateway Data port Command In terface User Guide • Authentication Mode configures the use of authen tication against a gatekeeper. • Authentication ID Configures the user name used within an authen tication challenge • Authentication Password sets the password used within the auth en tication process. NOTE! Authentication Pa ssword ...

  • TANDBERG D1320203 - page 16

    TANDBERG 3G Gateway Data port Command In terface User Guide used when t he 3G Gateway is connected t o a LAN usin g DHCP. Wh en using t his mode, IP-address and IP-subnet m ask are not used because the DHCP se rver supplies these parameters. • Address: Sets the static IP addres s for the gi ven LAN interface. • Subnetmask: Sets the subnet m ask ...

  • TANDBERG D1320203 - page 17

    TANDBERG 3G Gateway Data port Command In terface User Guide *c xConfiguratio n ISDN Internationa lPrefix: "00" Loadlimit Sets the processor-load percentag e at which ca lls should be rout ed to anot her 3G Gatewa y. LoadLimit: < 0..100> Example of Loadlimit feedba ck: *c xConfigur ation Loa dLimit: 85 Session Sets a timeout time for ...

  • TANDBERG D1320203 - page 18

    TANDBERG 3G Gateway Data port Command In terface User Guide SNMP HostIPAddr [1..3]: < IPAd dr> --- parameters: • Mode: < On/Off/ReadOnly/TrapsOnly > • Community Name: Text st ring of m aximum 16 cha racters. • System Contact: Text strin g of maxim um 70 characte rs • System Location: Text string of m aximum 70 c haracters • Ho ...

  • TANDBERG D1320203 - page 19

    TANDBERG 3G Gateway Data port Command In terface User Guide Telnet Enables or disables telnet interface on the 3G Gateway Telnet Mode: <On/Off> --- Example of Telnet feedback: *c xConfigurat ion Telnet Mode: On D1320203 1 9 ...

  • TANDBERG D1320203 - page 20

    TANDBERG 3G Gateway Data port Command In terface User Guide 4.2.2. General 3G Gateway Commands Command: Description: ExternalManager This command sets the path and address of the TMS serv er. A message is sent to TMS when the 3G Gateway starts up to signal TMS that the 3G Gateway is ready. ExternalMan ager Path: < S: 0, 255> or ExternalManage ...

  • TANDBERG D1320203 - page 21

    TANDBERG 3G Gateway Data port Command In terface User Guide OPC: <0 .. 16383> NetworkIndi cator: <Internati onal0/In ternational 1/National 0/Nationa l1> Law: <ALaw/ULaw> LinkSet [1 .. 2] Mode: <On/Off> LinkSet [1 .. 2] DPC: <0 .. 16383> LinkSet [1 .. 2] Link [1 .. 2] Mode: <On/Off> LinkSet [1 .. 2] Link [1 . . 2 ...

  • TANDBERG D1320203 - page 22

    TANDBERG 3G Gateway Data port Command In terface User Guide • Trunk CircuitIdentificationCode: The Circuit Identification Code is a unique id en tifier for a data time slot in a cable (trunk). In this case the CIC acts as base address and can be defined for eac h SS7 trun k and sets the first tim e-slot number of the respecti ve SS7 trunk. • Ro ...

  • TANDBERG D1320203 - page 23

    TANDBERG 3G Gateway Data port Command In terface User Guide *c xConfigur ation SS7 Tr unk 1 Mo de: Off *c xConfigur ati on S S7 Tr u nk 1 DPC : 0 *c xConfiguration SS7 Trun k 1 CircuitIdentificationCod e: 0 *c xConfigur ation SS7 Tr unk 2 Mo de: Off *c xConfigur ati on S S7 Tr u nk 2 DPC : 0 *c xConfiguration SS7 Trun k 2 CircuitIdentificationCod e ...

  • TANDBERG D1320203 - page 24

    TANDBERG 3G Gateway Data port Command In terface User Guide *c xConfigur ati on S S7 R out e 7 DPC : 0 *c xConfigur ation SS7 R oute 7 Priori ty: 0 *c xConfigur ation SS7 R oute 7 LinkSet : Off *c xConfigur ati on S S7 R out e 8 DPC : 0 *c xConfigur ation SS7 R oute 8 Priori ty: 0 *c xConfigur ation SS7 R oute 8 LinkSet : Off D1320203 2 4 ...

  • TANDBERG D1320203 - page 25

    TANDBERG 3G Gateway Data port Command In terface User Guide 4.2.3. System Status Commands Command: Description: BRI [1..4] Displays the status of the BRI lines BRI Parameters: • BRI [1..4] i ndicating th e status of the different BRI lines Example of BRI feedback: *s BRI 1 (ready=True): Channel 1 (type=BChannel , status=Idle): / Channel 2 (type=B ...

  • TANDBERG D1320203 - page 26

    TANDBERG 3G Gateway Data port Command In terface User Guide Nam e: "allowredirectivr" Value: " 0" Property: Nam e: "DTMFInfoScreen" Value: " On" *s/end OK Disk Diaplays information regard ing th e internal harddrive Disk Status format: < Status > < CheckDisk > Parameters: • Status is either OK o ...

  • TANDBERG D1320203 - page 27

    TANDBERG 3G Gateway Data port Command In terface User Guide Parameters: • Address , The IP address of the ex t ernal managem ent system • Protocol , the protocol used to acce ss the management system • URL , the URL on the m anagement syst em that shoul d be opened by the 3G Gateway in case of status updat es Example of Ex ternalManage r feed ...

  • TANDBERG D1320203 - page 28

    TANDBERG 3G Gateway Data port Command In terface User Guide • Port, the gatekeeper port t he 3G Gateway is connected with Example of H323Gatekeeper feedback: *s H323Gatekeeper (s tatus=Registered): Address: "10.47.9.1" Port: 1719 *s/end IP Displays the IP configuration of the 3G Gateway IP Status format: <Address> <SubnetMask&g ...

  • TANDBERG D1320203 - page 29

    TANDBERG 3G Gateway Data port Command In terface User Guide NTP Returns the IP address of the NTP server. Status format: < Status > <Address> <Port> <Last Update> <Last Correction> --- Parameters: • Status, indicates whether the NTP server is active or not. • Address, the IP addres s of the NTP server. • Port, is ...

  • TANDBERG D1320203 - page 30

    TANDBERG 3G Gateway Data port Command In terface User Guide Channel 10 (type=BChannel, status =Id le): / Channel 11 (type=BChannel, status =Id le): / Channel 12 (type=BChannel, status =Id le): / Channel 13 (type=BChannel, status =Id le): / Channel 14 (type=BChannel, status =Id le): / Channel 15 (type=BChannel, status =Id le): / Channel 16 (type=DCh ...

  • TANDBERG D1320203 - page 31

    TANDBERG 3G Gateway Data port Command In terface User Guide Name> ReleaseDate> Configuration Telephony:> VideoTelephony:> <Hardware : Version> SerialNumber> MainBoard> Additional Board> Configuration: PRI> TemperatureCelcius> TemperatureFahrenheit> --- Parameters: • ProductType , the name of the product, e.g. 3 ...

  • TANDBERG D1320203 - page 32

    TANDBERG 3G Gateway Data port Command In terface User Guide 4.2.4. Debug Commands Command: Desription : Syslog Enables a real- time log of B onding, H.221 and H 324m, ISDN , RTSP, IVi der, and IVide r Engine activi ty. Note! H323 and SIP loggi ng is prese nted using t he followi ng command: tsh –a H323 (SIP) . Note! Logging via the serial port is ...

  • TANDBERG D1320203 - page 33

    TANDBERG 3G Gateway Data port Command In terface User Guide 4.2.5. Special (Xcommand) Commands Command: Description: Boot Reboots the system. Example: xComm and Boot *r Result (status=OK): / *r/end OK CUIL rebo ot request , restarting CheckDisk This command shows t he presence and th e s tatus of the internal harddisk. Example: xComm and CheckDisk ...

  • TANDBERG D1320203 - page 34

    TANDBERG 3G Gateway Data port Command In terface User Guide • CallingParty: <S:0, 60> Service telephone number. • NetType: <All/H324m/H323/SIP> Nettype of t he end poin t to be called. • CallType: <Tlph/Vtlph> Call ty pe is either voi ce (Tl p h ), o r voi ce an d vi d e o (Vt lp h). OK Result parameter: • Session ID: < ...

  • TANDBERG D1320203 - page 35

    TANDBERG 3G Gateway Data port Command In terface User Guide EraseDisk This command wipes all the data from the internal harddisk Example: xComma nd EraseDisk *r Result (status=OK): *r/end OK FeedbackDeregister Command use d to deregi ster XML feedbac k over HTTP(S) . Parameters: • ID: <1 .. 3> I D for the regi stration to de register. OK Re ...

  • TANDBERG D1320203 - page 36

    TANDBERG 3G Gateway Data port Command In terface User Guide *r Result (status=OK): ID: 2 *r/end OK OptionKeyAdd Command used to set new option key s. Parameters: • Key(r): <S: 0, 90> opti o n key NOTE! Alway s reboot the system after adding o ption keys, for the opti on key to ta ke effect. Example: Xcomma nd OptionKey Add 115201 P1-1-6A96 ...

  • TANDBERG D1320203 - page 37

    TANDBERG 3G Gateway Data port Command In terface User Guide *r Result (status=OK): / *r/end OK D1320203 3 7 ...

  • TANDBERG D1320203 - page 38

    TANDBERG 3G Gateway Data port Command In terface User Guide General User Commands About Shows following system information: Software ve rsion: R3.0 Portions of this softwa re are licensed under 3r d pa rty licenses. See th e CD accompanying this product for det ails. Help or ? Displays the help menu. help Licence Shows 3 rd party licences License A ...

  • TANDBERG D1320203 - page 39

    TANDBERG 3G Gateway Data port Command In terface User Guide D1320203 3 9 (note: deregistration with index=0 will deregister all registered expressions) Examples : "xfeedback register status/ca ll" - t o monitor call changes "xfeedback register status/call--" - to monitor only call state changes "xfeedback register confi gur ...

Fabricant TANDBERG Catégorie Network Card

Les documents que nous recevons du fabricant de l'appareilTANDBERG D1320203 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques TANDBERG
- manuels d’utilisations D1320203
- fiches produit TANDBERG
- dépliants
- ou étiquettes-énergie TANDBERG D1320203
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation TANDBERG D1320203.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation TANDBERG D1320203, manuels d’entretien, brefs manuels ou manuels de l’utilisateur TANDBERG D1320203. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit TANDBERG D1320203.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil TANDBERG D1320203, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser TANDBERG D1320203 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs TANDBERG D1320203.

Le manuel d’utilisation complet TANDBERG, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel TANDBERG D1320203 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières TANDBERG D1320203, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lTANDBERG D1320203 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil TANDBERG D1320203 - qui devraient nous aider dans les premières étapes lors de l'utilisation TANDBERG D1320203
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de TANDBERG D1320203
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service TANDBERG D1320203 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de TANDBERG D1320203?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec TANDBERG D1320203, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec TANDBERG D1320203 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)