Français dropdown-ico

Manuel d’utilisation Anthem Audio MRX 710/510/310

60 pages 8.09 mb
Télécharger

Aller à la page of 60

Summary
  • Anthem Audio MRX 710/510/310 - page 1

    MRX 710 / 510 / 310 Audio/Video Receiver OPERATING MANUAL ...

  • Anthem Audio MRX 710/510/310 - page 2

    Anthem, AnthemLogic, ARC, and Paradigm are trademarks or registered trademarks of Paradigm Electronics Inc. © Paradigm Electronics Inc. All rights reserved. The information contained herein may not be reproduced in whole or in part without our express written permission. We reserve the right to change specifications and/or features without notice ...

  • Anthem Audio MRX 710/510/310 - page 3

    ...

  • Anthem Audio MRX 710/510/310 - page 4

    MRX 710 / 510 / 310 Audio/Video Receiver OPERATING MANUAL ...

  • Anthem Audio MRX 710/510/310 - page 5

    i IMPORTANT SAFETY INSTRUCTIONS CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE P ARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL RISK OF ELECTRIC SHOCK DO NO T OPEN The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of ...

  • Anthem Audio MRX 710/510/310 - page 6

    ii WARNING: T o reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. A void installing this unit where foreign objects may fall onto this unit and/or this unit may be exposed to liquid dripping or splashing. On the top of this unit, do not place: • Burning objects (i.e. candles), as they may cause fire, d ...

  • Anthem Audio MRX 710/510/310 - page 7

    iii DO NOT LOCATE IN THE FOLLOWING PLACES: T o ensure long-lasting use, do not locate the unit: • Exposed to direct sunlight. • Near sources of heat such as heaters. • Highly humid or poorly ventilated. • Dusty . • Subjected to mechanical vibrations. • On wobbly , inclined, or otherwise unstable surfaces. • Near windows where there is ...

  • Anthem Audio MRX 710/510/310 - page 8

    iv Cd Hg Pb NOTES ON ENVIRONMENTAL PROTECTION At the end of its useful life, this product must not be disposed of with r egular household waste but must be returned to a collection point for the recycling of electrical and electronic equipment. The symbol on the pr oduct, user’ s manual and packaging, point this out. The materials can be reused i ...

  • Anthem Audio MRX 710/510/310 - page 9

    v TABLE OF CONTENTS INTRODUCTION 1 1.1 Before Making Connections 1 1.2 In-Use Notices 2 1.3 Front Panel 3 1.4 Rear Panel MRX 710 4 1.5 Rear Panel MRX 310 5 1.6 Remote Control 6 1.7 Speaker Positioning CONNECTIONS 6 2.1 Video Connections 7 2.2 Audio Connections 10 2.3 Antennas 10 2.4 Local Area Network 10 2.5 12 Volt Trigger 10 2.6 Infra Red 10 2.7 ...

  • Anthem Audio MRX 710/510/310 - page 10

    1 Thank you for purchasing the Anthem MRX series r eceiver . The MRX 710 , MRX 510 , and MRX 310 receivers ar e cutting-edge home theater audio components with HDMI switching, video scaling and upconversion, state of the art room equalization, second zone capabilities, and FM/AM tuner . Anthem products ar e engineered to recr eate the passion of li ...

  • Anthem Audio MRX 710/510/310 - page 11

    2 1.3 FRONT PANEL MRX 710 shown, others are similar . For a larger diagram see inside back cover . 1 – Navigation buttons 2 – Display 3 – V olume, level functions, and character selection 4 – Power / standby 5 – Input selection 6 – Zone 2 selection 7 – Level selection 8 – Remote control sensor location 9 – Mode selection 10 – Di ...

  • Anthem Audio MRX 710/510/310 - page 12

    3 1.4 REAR PANEL MRX 710 MRX 710 US model shown. EU model, CN model, and MRX 510 are similar . 1 – FM/AM antenna connections 2 – HDMI inputs (HDMI1 accepts up to 4K resolution) 3 – HDMI outputs with Audio Return Channel 4 – AC input 5 – Local area network connection for IP contr ol and Anthem Room Corr ection 6 – USB jack for software u ...

  • Anthem Audio MRX 710/510/310 - page 13

    4 1.5 REAR PANEL MRX 310 US model shown. EU and CN models are similar . 1 – FM/AM antenna connections 2 – HDMI inputs (HDMI1 accepts up to 4K resolution) 3 – HDMI outputs with Audio Return Channel 4 – AC input 5 – Local area network connection for IP contr ol and Anthem Room Corr ection 6 – USB jack for software updates 7 – Component ...

  • Anthem Audio MRX 710/510/310 - page 14

    5 1.6 REMOTE CONTROL 1 – Main zone power on and standby 2 – Bass, T reble, Balance, Channel Level, Front panel dimmer 3 – Numeric keypad for tuner presets 4 – Input list 5 – T uner pr eset 6 – Setup menu 7 – Info and status 8 – Navigation controls 9 – Clear for deleting input configurations and tuner presets, and clearing new ent ...

  • Anthem Audio MRX 710/510/310 - page 15

    6 1.7 SPEAKER POSITIONING The illustrations below show typical 5.1 and 7.1-channel speaker placement. Bass response highly depends on r oom acoustics and experimentation with subwoofer placement is recommended. Anthem Room Corr ection can help with placement. 5.1 Channel 7.1 Channel ...

  • Anthem Audio MRX 710/510/310 - page 16

    7 This section describes connections between system components. Configuration of input and output will be discussed later , in section 3. 2.1 VIDEO CONNECTIONS HDMI With this type of connection, video and audio are carried together digitally . Maximum video resolution is 4K (also known as UHD and 2160p) at 30 frames per second for HDMI outputs and ...

  • Anthem Audio MRX 710/510/310 - page 17

    8 2.2 AUDIO CONNECTIONS AUDIO INPUTS AND OUTPUTS Digital audio sources can be connected with a coaxial, optical, or HDMI cable. These carry 2-channel PCM, Dolby Digital, and DTS. The HDMI inputs also accept up to eight channels of PCM, Dolby Digital T rueHD, DTS-HD, and DTS-HD Master Audio. Audio on the HDMI outputs is 2-channel PCM as this is mean ...

  • Anthem Audio MRX 710/510/310 - page 18

    9 SPEAKERS Connect using speaker wire. US models also allow banana plugs. MRX 710 and MRX 510 : If you are only using 5.1 speakers in the main zone, the two remaining amp channels may be congur ed for use in Zone 2, or to bi-amp front L/R in the main zone. Connect the positive (+) connection on the speaker to the positive (+) binding post on the ...

  • Anthem Audio MRX 710/510/310 - page 19

    10 2.3 ANTENNAS T o connect the AM loop antenna, press the spring-loaded tabs of the AM ANTENNA connector and insert the bare ends of the two wir es. Move the antenna until best reception is found. For the FM antenna, use the FM ANTENNA connector . Later , when unit is operating move the antenna to find best reception. 2.4 LOCAL AREA NETWORK This ...

  • Anthem Audio MRX 710/510/310 - page 20

    11 EXAMPLE 1 WA N 1 2 34 LAN HDMI OUT HDMI IN HDMI OUT WA N 1 2 34 LAN HDMI IN ...

  • Anthem Audio MRX 710/510/310 - page 21

    12 For optimum performance and enjoyment, your receiver should be pr operly set up. This may appear like a lot of work but most settings do not need to be changed from defaults. The important ones r elate to your display and input connections, and distance from listening ar ea to each speaker . Anthem Room Correction will set crossovers and channel ...

  • Anthem Audio MRX 710/510/310 - page 22

    13 3.1 HDMI OUTPUT CONFIGURATION Highlighting HDMI Output Configuration in the main menu then pressing Select displays this menu: HDMI COLOR DEPTH With the default Auto setting, color depth is set to the highest capability reported by the display’ s HDMI connection. The 12 and 10 bit formats are known as Deep Color and these will be used if comp ...

  • Anthem Audio MRX 710/510/310 - page 23

    14 3.2 SPEAKER SETUP If your source components also have bass management and time alignment, be sur e to disable them by setting all channels “large” and to the same distance from listener since the receiver will be performing these tasks. Audio quality will be degraded if these processes ar e performed twice. TWO CONFIGURATIONS One speaker con ...

  • Anthem Audio MRX 710/510/310 - page 24

    15 PROFILE NAME Using the navigation keys and volume knob each profile can be r enamed, up to 8 characters long. When finished, press Select but note that the pr ofile name is best set in Anthem Room Correction (T argets panel) because during file upload the name in the menu is overwritten by the one in ARC. CENTER / SURROUNDS / BACKS / SUBWOOF ...

  • Anthem Audio MRX 710/510/310 - page 25

    16 Bass Management Config 1 Config 2 3.3 BASS MANAGEMENT In this menu, information about your speakers is used so that bass does not become distorted. If using Anthem Room Correction, these items will be set during measurement, so you may skip this menu. If your subwoofer has a crossover , it should be bypassed – set its frequency control to th ...

  • Anthem Audio MRX 710/510/310 - page 26

    17 3.4 LISTENER POSITION Through these settings, sound coming fr om all speakers is coordinated to reach the listening area at the same time. This way , proper imaging is achieved. The channel with the greatest distance setting will have no delay while channels with shorter distance settings will be delayed accordingly . Distances may be set before ...

  • Anthem Audio MRX 710/510/310 - page 27

    18 3.5 LEVEL CALIBRATION Level Calibration uses internally generated test noises to match speaker output levels at the listening position. These noises are also a way of checking system connections between receiver , amplifier , and speaker . Audio calibrations from home theater setup discs are not r ecommended – some use incorrect methods. If u ...

  • Anthem Audio MRX 710/510/310 - page 28

    19 3.6 INPUT SETUP Inputs and listening mode presets ar e configured in this section. From the factory , 5 inputs are set but you may change this to anything fr om 1 to 20 configurations. T o add an input at the end of the list, highlight Add Input and press Select. T o insert an input, highlight one on the list and press Input. The new input wil ...

  • Anthem Audio MRX 710/510/310 - page 29

    20 INPUT NAME Using the navigation keys and volume knob each input can be renamed, up to 8 characters long. When finished, press Select. Example – Rename “HDMI 1” to “Blu-ray”: • Highlight “Input Name” and press Select. The first character will be highlighted in red. • Use the up/down buttons or volume knob to change “H” to ...

  • Anthem Audio MRX 710/510/310 - page 30

    21 LISTENING MODE PRESETS A listening mode is processing that enhances sour ce material by increasing the number of output channels. Each mode performs this its own way , pr oviding its own type of sound. T o find your preference, spend some time listening to various modes using various sour ces. T o disable presets and make selections entirely on ...

  • Anthem Audio MRX 710/510/310 - page 31

    22 FOR 5.1-CHANNEL SOURCES (MRX 710/510) 7.1 speakers are needed in the main zone. Dolby Pro Logic IIx Movie is suitable for extracting back channels fr om any 5.1-channel source. Dolby Pro Logic IIx Music is similar but with incr eased emphasis on the surround channels. DTS Neo:6 is also suitable for extracting back channels from any 5.1-channel s ...

  • Anthem Audio MRX 710/510/310 - page 32

    23 3.7 VOLUMES / REC OUTPUT Here you can set pr eferences as listed. MUTE LEVEL When Mute is pressed, sound can cut out completely or decr ease in volume by the amount that you set to keep some of it in the background. Select fr om Silent or -5 to -30 dB in 5 dB steps. MAXIMUM VOLUME These settings allow you to limit the volume setting to avoid dam ...

  • Anthem Audio MRX 710/510/310 - page 33

    24 3.8 NETWORK / REMOTE CONTROL DEVICE NAME: This is the name that the receiver br oadcasts, and it can be changed using up to 16 characters. NETWORK TYPE: The default is wired LAN, which will allow the easiest way to run Anthem Room Correction, described later , as long as the receiver is connected to an Ethernet router . The alternative is to cha ...

  • Anthem Audio MRX 710/510/310 - page 34

    25 IP CONFIGURATION Settings in this submenu should only be changed if your network administrator gives the direction or if using Dir ect Connect to run ARC. MODE Static IP settings take effect once this is changed to Manual. For ARC, enter the IP , Subnet Mask, and Gateway values shown above (note that the receiver’ s IP address is not the same ...

  • Anthem Audio MRX 710/510/310 - page 35

    26 TCP AND UDP PORT Change these only if there is a conflict with another application that uses 14999. REAR AND FRONT IR This allows you to disable each of the receiver’ s infra-red inputs, which can be useful when the receiver is connected to an IR r epeater and is receiving too many signals. Note that the moment that you disable the front IR i ...

  • Anthem Audio MRX 710/510/310 - page 36

    27 3.9 DISPLAY The front panel display’ s brightness is set here. BRIGHTNESS: Set preferr ed default brightness. WAKE UP BRIGHTNESS: When a button is pressed the display can go to a brighter level for 5 seconds – select None, Up 1 brightness level, Medium, or High. When “None” is selected and the display is off, the wake-up behaves as Up 1 ...

  • Anthem Audio MRX 710/510/310 - page 37

    28 AUTO OFF When there is no input signal the r eceiver will tur n off after the selected time: 5, 10, or 30 minutes, 1, 2, or 6 hours, or Never . ECO MODE When enabled, options that increase power consumption during standby ar e disabled. With default settings, just under 0.3 W is consumed in standby . IP CONTROL With this setting you can enable/d ...

  • Anthem Audio MRX 710/510/310 - page 38

    29 CEC When Consumer Electronics Contr ol is enabled it allows controlling one HDMI- connected component using another’ s remote control, as long as CEC is also enabled in the other components. Note that when component brands are mixed this contr ol system may not be reliable. CEC Control must also be On for Audio Return Channel, described in an ...

  • Anthem Audio MRX 710/510/310 - page 39

    30 SAVE/LOAD USER SETTINGS After selecting Save User Settings and confirming, all menu settings will be stored. If you change settings later and want to recall the saved settings, select Load User Settings and confirm. RESET ON-THE-FLY SETTINGS After selecting and confirming, all non-menu settings such as level and bass/treble will be reset. LOA ...

  • Anthem Audio MRX 710/510/310 - page 40

    31 3.12 SYSTEM INFORMATION UPDATE VIA USB AND VERSION NUMBERING: The operational characteristics of the receiver ar e controlled by software installed through the USB port on the r ear panel. Updates can be downloaded from our web site and installed afterwards. • On www .anthemAV .com locate the software pertaining to your MRX model and voltage. ...

  • Anthem Audio MRX 710/510/310 - page 41

    32 ANTHEM ROOM CORRECTION ARC corrects the ef fects of reflective surfaces and room boundaries on sound quality by measuring the response of each speaker r elative to the listening area and equalizing it. ARC equalizes response without str essing the amplifier or speakers and does not downsample the source material to pr ocess it. ARC’ s filte ...

  • Anthem Audio MRX 710/510/310 - page 42

    33 4.1 BEFORE STARTING • Ensure that the r eceiver software and ARC-2 software that you will be using ar e compatible with one another – check www .anthemAV .com for latest versions. • Y our ARC micr ophone and its support file are a system. Before a mic can be used for measurement, its r esponse must be known. Each ARC microphone’ s frequ ...

  • Anthem Audio MRX 710/510/310 - page 43

    34 4.3 MICROPHONE STAND ASSEMBLY Screw the telescoping tube into its base and the micr ophone clip onto the tube. Position the clip vertically . Connect the USB micr ophone cable to the microphone and slide the microphone into the clip. 4.4 MICROPHONE POSITIONING During measurement the micr ophone must point straight up. The microphone’ s height ...

  • Anthem Audio MRX 710/510/310 - page 44

    35 4.6 MANUAL MODE AND TARGETS When creating a new file, manual mode is the same as automatic mode except that you must measure, calculate, and upload in separate steps. After the measur ement phase, targets can be edited but doing so is recommended only for experienced users. A file created in Automatic mode can be opened in Manual mode to allow ...

  • Anthem Audio MRX 710/510/310 - page 45

    36 If you did change settings such that a large portion of the bass is being boosted, as would be shown by a wide range of the green corr ected curve having higher level than the red measur ed curve, chances are that your equipment will be stressed mor e than the sound will improve. Ther e is very little to gain by doing this. Instead, address the ...

  • Anthem Audio MRX 710/510/310 - page 46

    37 SUBWOOFER HIGH PASS FREqUENCY Use this with High Pass Order when manually cr eating a curve on the lower end of the subwoofer’ s response. The left side of the red measur ed curve is the guideline for shaping the target curve. An attempt to use this as a bottom-end boost to increase low-frequency output is likely to be detrimental to the subwo ...

  • Anthem Audio MRX 710/510/310 - page 47

    38 OPERATION 5.1 POWER ON / OFF AND VOLUME Main and Zone 2 have separate power controls. During power -on and power -off a mechanical click is produced fr om the unit – this is normal. V olume comes on according to setup menu setting. T o control volume rotate the fr ont panel knob or press VOL up/down on the remote control. T o mute or un-mute t ...

  • Anthem Audio MRX 710/510/310 - page 48

    39 5.3 INPUT SELECTION The number of active inputs varies according to how the Input Setup menu was programmed. T o scroll thr ough the next/previous active inputs press the right/left buttons, and to make a selection press SELECT . Alternatively , press the INPUT button for an on-scr een list of inputs. Use the up/down and SELECT buttons to change ...

  • Anthem Audio MRX 710/510/310 - page 49

    40 PRESETS (r emote control only) 30 AM and 30 FM stations can be stored. T o store the curr ent station press PRESET then assign a number from 01 to 30. T o recall a preset enter the assigned number or pr ess PG/PR up/down for the next/ previous one. T o delete a preset, select it then press CLEAR. 5.5 LEVEL TRIM If a channel group, for example th ...

  • Anthem Audio MRX 710/510/310 - page 50

    41 5.6 BASS / TREBLE / BALANCE T o change tone, press Bass or T r eble on the remote control then up/down. Note that Bass does not affect the subwoofer output – this is handled by the Level adjustment. T o change balance press BAL on the remote then up to move the image to the right, or down to move the image to the left. 5.7 LIP-SYNC If the audi ...

  • Anthem Audio MRX 710/510/310 - page 51

    42 5.9 DOLBY VOLUME AND DYNAMIC RANGE CONTROL Refer to the Input Setup section for a description of Dolby V olume. T o change on/off status press DYN on the r emote control then up/down. T o change Leveler amount press DYN a second time when Dolby V olume is on then adjust. When Dolby V olume is off another dynamic range control becomes available a ...

  • Anthem Audio MRX 710/510/310 - page 52

    43 PREAMPLIFIER Maximum Output (<0.1% THD . . . . . . . 3.5 Vrms, subwoofer channel 6.1 V rms Frequency Response (2 V rms output) . . . . . . . 8 Hz to 28 kHz (+0, -0.25 dB) Frequency Response, Analog-Direct mode (2 V rms output) . . . . . . . . 8 Hz to 50 kHz (+0, -0.25 dB) THD+N (2 V rms output) . . . . . . . . . . . . . . . . . . . . . . < ...

  • Anthem Audio MRX 710/510/310 - page 53

    44 CANADA & USA The warranty period on new Anthem products is: 5 years: Separate power amplifiers and integrated amplifiers 3 years: Audio/Video preamplifiers and r eceivers Please register your pr oduct at www .anthemA V .com The warranty period begins on the date of purchase fr om Anthem or an Authorized Anthem Dealer . This warranty is of ...

  • Anthem Audio MRX 710/510/310 - page 54

    45 THE BIG PICTURE FRONT PANEL (MRX 710) ZONE 2M AIN MRX 710 ...

  • Anthem Audio MRX 710/510/310 - page 55

    46 THE BIG PICTURE REAR PANEL (MRX 710) ...

  • Anthem Audio MRX 710/510/310 - page 56

    47 THE BIG PICTURE REAR PANEL (MRX 310) ...

  • Anthem Audio MRX 710/510/310 - page 57

    NOTES ...

  • Anthem Audio MRX 710/510/310 - page 58

    NOTES ...

  • Anthem Audio MRX 710/510/310 - page 59

    NOTES ...

  • Anthem Audio MRX 710/510/310 - page 60

    DESIGNED IN NORTH AMERICA +1 905-564-1994 9:00 am - 5:30 pm M-F (ET) www .anthemA V .com 2MAN0092 En 2013-10-23 ...

Fabricant Anthem Audio Catégorie Stereo Receiver

Les documents que nous recevons du fabricant de l'appareilAnthem Audio MRX 710/510/310 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Anthem Audio
- manuels d’utilisations MRX 710/510/310
- fiches produit Anthem Audio
- dépliants
- ou étiquettes-énergie Anthem Audio MRX 710/510/310
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Anthem Audio MRX 710/510/310.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Anthem Audio MRX 710/510/310, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Anthem Audio MRX 710/510/310. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Anthem Audio MRX 710/510/310.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Anthem Audio MRX 710/510/310, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Anthem Audio MRX 710/510/310 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Anthem Audio MRX 710/510/310.

Le manuel d’utilisation complet Anthem Audio, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Anthem Audio MRX 710/510/310 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Anthem Audio MRX 710/510/310, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lAnthem Audio MRX 710/510/310 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Anthem Audio MRX 710/510/310 - qui devraient nous aider dans les premières étapes lors de l'utilisation Anthem Audio MRX 710/510/310
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Anthem Audio MRX 710/510/310
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Anthem Audio MRX 710/510/310 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Anthem Audio MRX 710/510/310?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Anthem Audio MRX 710/510/310, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Anthem Audio MRX 710/510/310 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)