Français dropdown-ico

Manuel d’utilisation Barco R9000908

55 pages 2.27 mb
Télécharger

Aller à la page of 55

Summary
  • Barco R9000908 - page 1

    GRAPHICS 808s R9000901 R9000908 OWNER'S MANUAL ...

  • Barco R9000908 - page 2

    BARCO PROJECTION SYSTEMS Date : 051196 Art. No. : R5975007 GRAPHICS 808s R9000901 R9000908 OWNER'S MANUAL ...

  • Barco R9000908 - page 3

    Due to constant research, the information in this manual is subject to change without notice. Produced by BARCO NV, November 1996. All rights reserved. Trademarks are the rights of their respective owners. Printed in Belgium BARCO nv/Projection Systems Noordlaan 5 B-8520 Kuurne Belgium Printed in Belgium R9000901 : BARCOGRAPHICS 808s 230V R9000908 ...

  • Barco R9000908 - page 4

    Table of Contents i-1 5975007 BARCOGRAPHICS 808s 160996 Table of contents ........................................................................................................................................................................... i Safety instructions .................................................................................. ...

  • Barco R9000908 - page 5

    Table of Contents i-2 5975007 BARCOGRAPHICS 808s 160996 Blanking Adjustments ........................................................................................................... ............................................. 6-15 Convergence Adjustment ........................................................................................... ...

  • Barco R9000908 - page 6

    Safety Instructions 1-1 5975007 BARCOGRAPHICS 808S 090996 WARNING TO PREVENT FIRE OR ELECTRICAL SHOCK HAZARD, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE FEDERAL COMMUNICATION COMMISSION (FCC STATEMENT) This equipment has been tested and found to comply with the limits of a class A digital device, pursuant to Part 15 of the FCC Rules. These li ...

  • Barco R9000908 - page 7

    Safety Instructions 1-2 5975007 BARCOGRAPHICS 808S 090996 A. Mains lead (Power cord) with CEE 7 plug : The wires of the mains lead are colored in accordance with the following code. Green and yellow: earth (safety earth) Blue: neutral Brown: line (live) B. Power cord with ANSI 73.11 plug : The wires of the power cord are colored in accordance with ...

  • Barco R9000908 - page 8

    Location and Functions of Control 2-1 5975007 BARCOGRAPHICS 808S 090996 2 LOCA TION AND FUNCTION OF CONTROLS REAR PANEL TERMINOLOGY POR T 4 /5 See installation instructions before connecting to t he supply. Vo ir la n oti ce d 'i nstal la t i on a van t d e ra cco r der au r ésea u . 120/ 230 V 7/ 5 Am p 50/60 Hz 75 Ohm PORT 2 75 Ohm 1 2 3 4 ...

  • Barco R9000908 - page 9

    Location and Functions of Control 2-2 5975007 BARCOGRAPHICS 808S 090996 Control panel terminology GRAPHICS a. The Local Keypad Getting Access The local keypad is underneath the top cover door with the BARCO logo. To open this door, push as indicated on drawing and turn it to the front side of the projector. This local keyboard has the same function ...

  • Barco R9000908 - page 10

    Connections 3-1 5975007 BARCOGRAPHICS 808S 051196 3 CONNECTIONS PORT 4 /5 See install ation inst ruct ions b efore c onnecti ng t o t he sup ply. Voir la n otice d'inst allatio n avant de racco r der au r é seau. 120/230 V 7/5 Amp 50/6 0 Hz 75 Ohm PORT 2 75 Ohm This device c omp lies wit h part 15 of th e F CC ru le s. Op era ti on is su bj e ...

  • Barco R9000908 - page 11

    Connections 3-2 5975007 BARCOGRAPHICS 808S 051196 PROJECT OR WARM UP A FULL WHITE PATTERN WI LL BE GENE RATED FO R 20 MIN UTES. FOR IMMEDIATE USE OF THE PROJEC T OR, PRESS <EXIT>. WA RNI NG : SKIP PI NG THIS PRO C EDUR E CA N RE DUC E THE I NITIAL P ICTURE QUALITY OF THE PROJECTED IMAGE. THI S OP TION CAN B E DISABLED I N THE SERVI C E MENU W ...

  • Barco R9000908 - page 12

    Connections 3-3 5975007 BARCOGRAPHICS 808S 051196 Connecting a Composite Video source to port 1. Composite video signals from a VCR, OFF air signal decoder, etc.. PORT 4/5 See install a tion instructions b e fore connecting to the supply . Voir la notice d'install ation avant de raccorder au r é s eau. 120/230 V 7/5 Amp 50/ 60 Hz 75 Ohm PORT ...

  • Barco R9000908 - page 13

    Connections 3-4 5975007 BARCOGRAPHICS 808S 051196 Connecting a RGB Analog source to port 3. Connect your RGB source via an interface to Port 3. Always use an interface when a computer and local monitor have to be connected to the projector. Barco interfaces which can be applied : Universal analog interface R9826100 RGB 120 MHz analog interface R982 ...

  • Barco R9000908 - page 14

    Connections 3-5 5975007 BARCOGRAPHICS 808S 051196 Connecting a RGB Analog source with Tri-level sync to port 4/5. (option) RGB analog input terminals with Tri level sync input or with Tri-level sync on green. The projector detects automatically where the sync signal is located. PORT 4/ 5 See i ns tallation ins tructio ns befor e connecting to the s ...

  • Barco R9000908 - page 15

    Connections 3-6 5975007 BARCOGRAPHICS 808S 051196 PERIPHERAL EQUIPMENT Connecting a RCVDS 05 switcher to the BARCOGRAPHICS 808s - Up to 20 inputs with the RCVDS 05 switcher and up to 90 inputs when 10 RCVDS switchers are linked via the expansion modules. - Serial communication with the projector. - Remote control buttons on the RCVDS to control the ...

  • Barco R9000908 - page 16

    Controlling 4-1 5975007 BARCOGRAPHICS 808sS 160996 4 CONTROLLING Caution : Do not display a stationary image with full brightness and contrast for longer than 20 min., otherwise you risk damage to the CRT's. Battery installation in the RCU. A new battery (not yet installed to save the battery life) is delivered inside the plastic bag with the ...

  • Barco R9000908 - page 17

    Controlling 4-2 5975007 BARCOGRAPHICS 808sS 160996 The BARCOGRAPHICS 808s can be controlled with a. the RCU b. the hardwired RCU (cable not included) c. the built-in RCU (local keypad) The procedure and results of controlling the projector with either of these RCU options is essentially the same. How to use your RCU a) Point the front of the RCU to ...

  • Barco R9000908 - page 18

    Controlling 4-3 5975007 BARCOGRAPHICS 808sS 160996 Port No Projector input Press Digit Button 1 Comp. Video 1 2 S-Video 1 /Comp. Video* 2 3 RGB 2 3 4/5 RGB 2 4 or 5 4/5 Component video 3 6 4/5 RGB with Tri level sync 4 7 4/5 Component video with Tri-level sync 5 8 How to display a projector address? Press the ADDRESS key (recessed key on the RCU) w ...

  • Barco R9000908 - page 19

    Controlling 4-4 5975007 BARCOGRAPHICS 808sS 160996 Analog Picture Controls The analog picture controls can be adjusted with the RCU. The control keys are located on the lower right side of the key panel of the RCU and indicated with the name of the control and an icon. When an analog picture control is pressed, a text box with bar scale and the fun ...

  • Barco R9000908 - page 20

    Start Up of the Adjustment Mode 5-1 5975007 BARCOGRAPHICS 808S 160996 5 ST ART UP OF THE ADJUSTMENT MODE Adjustment Mode All picture geometry and convergence adjustments are made while in the 'Adjustment mode'. Press the ADJUST key to enter the 'adjustment mode'. You are now in the 'Adjustment mode' . The Control stick ...

  • Barco R9000908 - page 21

    Start Up of the Adjustment Mode 5-2 5975007 BARCOGRAPHICS 808S 160996 Some items in the Adjustment mode are password protected. While selecting such an item, the projector asks you to enter your password. (Password protection is only available when the password DIP switch on the controller module is in the ON position. Contact a BARCO authorized te ...

  • Barco R9000908 - page 22

    Random Access Adjustment Mode 6-1 5975007 BARCOGRAPHICS 808S 051196 6 RANDOM ACCESS ADJUSTMENT MODE Starting-Up the Random Access Adjustment mode. Push the control stick forward or backward to highlight "RANDOM ACCESS" and then press ENTER . Some items in the Random access mode are password protected (when the password function is enabled ...

  • Barco R9000908 - page 23

    Random Access Adjustment Mode 6-2 5975007 BARCOGRAPHICS 808S 051196 RANDOM ACCESS ADJUSTMENT MODE CONVERGENCE H SIZE V SIZE BLANKING LEFT BOTTOM RIGHT TOP V LINEARITY GREEN ONLY BLUE ON GREEN RED ON GREEN FOCUSING BLUE GREEN RED BLUE GREEN RED RED AND BLUE BLUE AND GREEN RED AND GREEN COLOR SELECT ORBITING CONTRAST MODULATION SOFT EDGE CORRECTION F ...

  • Barco R9000908 - page 24

    Random Access Adjustment Mode 6-3 5975007 BARCOGRAPHICS 808S 051196 Selecting Setup Pattern If an external source is connected to the projector, this menu will be displayed. Push the control stick forward or backward to highlight the desired setup pattern and then press ENTER . Genlocked pattern : internally generated cross hatch pattern, locked on ...

  • Barco R9000908 - page 25

    Random Access Adjustment Mode 6-4 5975007 BARCOGRAPHICS 808S 051196 Select with or then <ENTER> <EXIT> to return. RANDOM ACCESS ADJUSTMENT MODE PICTURE TUNING GEOMETRY CONVERGENCE FOCUSING COLOR SELECT ORBITING CONTR. MODULATION SOFT EDGE Select with or <ENTER> to accept <EXIT> to return. PICTURE TUNING COLOR BALANCE SYNC : ...

  • Barco R9000908 - page 26

    Random Access Adjustment Mode 6-5 5975007 BARCOGRAPHICS 808S 051196 Sync Fast/Slow Adjustment The sync function is used to minimize horizontal jittering or tearing at the top to the displayed image. Highlight SYNC by pushing the control stick forward or backward and press ENTER to toggle between FAST and SLOW . Note: SYNC is normally used in the SL ...

  • Barco R9000908 - page 27

    Random Access Adjustment Mode 6-6 5975007 BARCOGRAPHICS 808S 051196 Port 2 : Video or S-Video Port 2 can be used as a Video or S-Video input. Highlight Port 2 by pushing the control stick forward or backward and press ENTER to toggle between VIDEO and S-VIDEO. Select with or <ENTER> to accept <EXIT> to return. PICTURE TUNING COLOR BALAN ...

  • Barco R9000908 - page 28

    Random Access Adjustment Mode 6-7 5975007 BARCOGRAPHICS 808S 051196 Focusing Before starting the 'focusing' adjustment, be sure the lenses are correctly focused. Push the control stick forward or backward to select 'Focusing' and press ENTER . Select with or then <ENTER> <EXIT> to return. RANDOM ACCESS ADJUSTMENT MOD ...

  • Barco R9000908 - page 29

    Random Access Adjustment Mode 6-8 5975007 BARCOGRAPHICS 808S 051196 Geometry Adjustments The geometry adjustments have to be done only on the green image. These adjustments are automatically implemented for the other color images : Left-right (EW) and Top-Bottom Corrections, Blanking, Horizontal Amplitude, Vertical Amplitude, Vertical Linearity and ...

  • Barco R9000908 - page 30

    Random Access Adjustment Mode 6-9 5975007 BARCOGRAPHICS 808S 051196 Raster Shift Adjustment The green raster must be centered both horizontally and vertically on the center of the CRT surface. To center the green raster, look into the green lens and use the control stick to move the raster. CAUTION It is necessary to look into the lenses to perform ...

  • Barco R9000908 - page 31

    Random Access Adjustment Mode 6-10 5975007 BARCOGRAPHICS 808S 051196 Left-Right (east-west) Adjustments Left-right adjustments affect only the vertical lines of the projected image. Only the green image is displayed while making left-right adjustments. The red and blue images will automatically be corrected in the same manner. Convergence correctio ...

  • Barco R9000908 - page 32

    Random Access Adjustment Mode 6-11 5975007 BARCOGRAPHICS 808S 051196 Seagull correction Use this correction only if, after adjusting the vertical lines with the side bow or side keystone, still a 'S' deformation is visible on the left and the right side of the image. The default value on the bar scale for this correction is 50. Push the c ...

  • Barco R9000908 - page 33

    Random Access Adjustment Mode 6-12 5975007 BARCOGRAPHICS 808S 051196 Top-Bottom (north-south) Adjustments Top-Bottom and center adjustments affect only the horizontal lines of the projected image. To start up the Top-Bottom and center corrections, follow the next procedure : Push the control stick forward or backward to highlight TOP-BOT- TOM (N/S) ...

  • Barco R9000908 - page 34

    Random Access Adjustment Mode 6-13 5975007 BARCOGRAPHICS 808S 051196 Seagull Correction Use this correction after the image has been adjusted with top and bottom bow and keystone. If still a deformation (like a seagull) on top and bottom of the image is visible, proceed to the seagull correction. Due to interaction, it is possible that the top and ...

  • Barco R9000908 - page 35

    Random Access Adjustment Mode 6-14 5975007 BARCOGRAPHICS 808S 051196 Vertical Linearity Adjustment The vertical linearity adjustment function corrects for vertical non- linearities which extend from the center of the image to the top and bottom of the image. Push the control stick forward or backward to highlight V LINEARITY on the Geometry menu an ...

  • Barco R9000908 - page 36

    Random Access Adjustment Mode 6-15 5975007 BARCOGRAPHICS 808S 051196 Blanking Adjustments Blanking adjustments affect only the edges of the projected image and are used to frame the projected image on to the screen and to hide or black out unwanted information (or noise). A 0% on the bar scale indicates no blanking. To start up the Blanking adjustm ...

  • Barco R9000908 - page 37

    Random Access Adjustment Mode 6-16 5975007 BARCOGRAPHICS 808S 051196 Select with or then <ENTER> <EXIT> to return. RANDOM ACCESS ADJUSTMENT MODE PICTURE TUNING GEOMETRY CONVERGENCE FOCUSING COLOR SELECT ORBITING CONTR. MODULATION SOFT EDGE Convergence Adjustment Convergence adjustments affect both the horizontal and vertical lines of th ...

  • Barco R9000908 - page 38

    Service Mode 7-1 5975007 BARCOGRAPHICS 808s 160996 Starting up the Service mode. Use the control stick to highlight 'Service' and then press ENTER . Some items in the Service mode are password protected (when the password function is active). Enter your password to continue. All other password protected items are now also free available i ...

  • Barco R9000908 - page 39

    Service Mode 7-2 5975007 BARCOGRAPHICS 808s 160996 Identification Highlight 'Identification' with the control stick and press ENTER . The 'Identification' screen gives information concerning : - projector address. To change the address of your projector, contact a qualified service technician. - software version. - configuration ...

  • Barco R9000908 - page 40

    Service Mode 7-3 5975007 BARCOGRAPHICS 808s 160996 Deletion of blocks This item is password protected. The delete function is used to clear all data (settings) from an adjustment block. A delete can be given : - block by block or - for all blocks. Deleting block by block The delete a block function deletes the settings of a selected block. Highligh ...

  • Barco R9000908 - page 41

    Service Mode 7-4 5975007 BARCOGRAPHICS 808s 160996 Change password This item is password protected. Highlight 'change password' with the control stick and press ENTER . The current password is displayed. The new password must consist of 4 digits between 0 and 9. Push the control stick to the left or to the right to select the digits to be ...

  • Barco R9000908 - page 42

    Service Mode 7-5 5975007 BARCOGRAPHICS 808s 160996 Set to midposition Item is password protected. Highlight 'set to midposition' with the control stick and press ENTER to set all settings to their midposition. A confirmation menu will be displayed first. Select with or then <ENTER> <EXIT> to return. SERVICE MODE IDENTIFICATION ...

  • Barco R9000908 - page 43

    Service Mode 7-6 5975007 BARCOGRAPHICS 808s 160996 When undo is pressed all convergence settings are reset to the previous settings. Dynamic Astigmatism (spot shape adjustment) The spot shape adjustments correct the spot shape in 8 different areas on the screen and that for the three colors separately. The spot shape is adjusted according to the ax ...

  • Barco R9000908 - page 44

    Service Mode 7-7 5975007 BARCOGRAPHICS 808s 160996 Use the up and down arrow keys for the diagonal astigmatism adjustment and the left and right arrow keys for the axial astigmatism adjustment. Press ENTER to continue selecting a new area. The adjustment direction (axial or diagonal) and adjustment value are given in a text box on the screen. When ...

  • Barco R9000908 - page 45

    Service Mode 7-8 5975007 BARCOGRAPHICS 808s 160996 Projector Warm Up Highlight 'Projector Warm Up' by pushing the control stick forward or backward and press ENTER to select the projector warm up menu. Select with or then <ENTER> <EXIT> to return. SERVICE MODE G2 ADJUSTMENT GAMMA CORRECTIONS CRT RUN IN CYCLE PROJECTOR WARM UP ...

  • Barco R9000908 - page 46

    Messages, warnings and failure codes 8-1 5975007 BARCOGRAPHICS 808s 160996 8 MESSAGES, W ARNINGS AND F AILURE CODES SOURCE 01 Fh= 15.6 kHz Fv= 050 Hz SOURCE 01 Fh= 15.6 kHz Fv= 050 Hz Announcement of the selected source. enter password xxxx Message to enter your password. Password contains 4 digits. text on text off These messages will be dis- play ...

  • Barco R9000908 - page 47

    Messages, warnings and failure codes 8-2 5975007 BARCOGRAPHICS 808s 160996 WARNING : go to stand by Projector will switch to 'stand-by' when the RCVDS is no longer available. WARNING : invalid frequency input The entered frequency or ap- plied frequency of the source is out of the projector's range. WARNING : default settings loaded ...

  • Barco R9000908 - page 48

    Options 9-1 5975007 BARCOGRAPHICS 808s 051196 IR Receiver 800 This infrared receiver unit makes it possible to control the BARCOGRAPHICS 808s from another room. There is a communication line with cable between the IR receiver and the projector or the RCVDS05. The control information from the RCU can now be sent to this IR receiver. The IR receiver ...

  • Barco R9000908 - page 49

    Options 9-2 5975007 BARCOGRAPHICS 808s 051196 MAGIK Interface Multifuctional Analog Graphics Interface Kit. BARCO's MAGIK interface allows the user to connect a presentation device such as a projector or a professional monitor to any computer with analog video signal with or without maintaining the connection with its own display. The MAGIK in ...

  • Barco R9000908 - page 50

    Orbiting A-1 5975007 BARCOGRAPHICS 808s 160996 A ORBITING Orbiting (option) Static pictures are very often shown on large screen projectors, espectially in process control and presentation applications. Due to the fact that the same picture information is shown for a long period on the same place, picture tubes can be damaged by 'local burn-in ...

  • Barco R9000908 - page 51

    Orbiting A-2 5975007 BARCOGRAPHICS 808s 160996 Orbiting Speed Toggle (only in MASTER Orbiting) Highlight 'SPEED : SLOW' with the control stick and press ENTER to set the ORBITING SPEED to Fast. Highlight 'SPEED : FAST' with the control stick and press ENTER to set the ORBITING SPEED to Slow <EXIT> to return. MASTER ORBITIN ...

  • Barco R9000908 - page 52

    Orbiting A-3 5975007 BARCOGRAPHICS 808s 160996 Adjustment procedure multiple projector installations : Inportant : to allow corrections in the deviation alignments of the slave projectors, never adjust the deviations of the master projector to its maximum. Default setting of the Master projectorn see 'Stand-Alone projector'. Highlight &ap ...

  • Barco R9000908 - page 53

    Adjustment Blocks and Source Numbers 90-99 B-1 5975007 BARCOGRAPHICS 808s 160996 Adjustment Blocks (memory blocks) As the BARCOGRAPHICS 808s is digitally controlled, all geometry and convergence adjustments are stored in the projector ’ s memory as numeric values. These numeric values are used to control digital potentiometers which in turn, cont ...

  • Barco R9000908 - page 54

    Adjustment Blocks and Source Numbers 90-99 B-2 5975007 BARCOGRAPHICS 808s 160996 The alternate adjustment block for sources 0 - 9 (projector with RCVDS) or 1 - 5 (stand-alone projector) is activated by selecting the corresponding source number 0 - 9 (projector with RCVDS) or 1 - 5 (stand-alone projector). Once this source number is selected, the al ...

  • Barco R9000908 - page 55

    Insert Card i-1 5975007 BARCOGRAPHICS 808s 160996 P RCU INP UT S OURCE S 1 PROJECTOR RCV DS 2 3 4 5 6 1 2 3 5 6 7 8 9 10 INP UT S OURCE S 7 P RCU INP UT S OURCE S 1 PROJECTOR RCV DS 2 3 4 5 6 1 2 3 5 6 7 8 9 10 INP UT S OURCE S 7 INSERT CARD ...

Fabricant Barco Catégorie Projector

Les documents que nous recevons du fabricant de l'appareilBarco R9000908 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Barco
- manuels d’utilisations R9000908
- fiches produit Barco
- dépliants
- ou étiquettes-énergie Barco R9000908
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Barco R9000908.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Barco R9000908, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Barco R9000908. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Barco R9000908.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Barco R9000908, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Barco R9000908 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Barco R9000908.

Le manuel d’utilisation complet Barco, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Barco R9000908 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Barco R9000908, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lBarco R9000908 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Barco R9000908 - qui devraient nous aider dans les premières étapes lors de l'utilisation Barco R9000908
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Barco R9000908
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Barco R9000908 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Barco R9000908?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Barco R9000908, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Barco R9000908 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)