Français dropdown-ico

Manuel d’utilisation Omega Engineering OME-PIO-D96

51 pages 1.46 mb
Télécharger

Aller à la page of 51

Summary
  • Omega Engineering OME-PIO-D96 - page 1

    www .omega.com e-mail: info@omega.com U ser ’ s Guide OME-PIO-D96 PCI-Bus Digital I/O Board Hardware Manual Shop online at ...

  • Omega Engineering OME-PIO-D96 - page 2

    Servicing Nor th America: USA: One Omega Drive, P.O. Box 4047 ISO 9001 Certified Stamford CT 06907-0047 TEL: (203) 359-1660 FAX: (203) 359-7700 e-mail: info@omega.com Canada: 976 Bergar Laval (Quebec) H7L 5A1, Canada TEL: (514) 856-6928 FAX: (514) 856-6886 e-mail: info@omega.ca For immediate technical or application assistance: USA and Canada: Sale ...

  • Omega Engineering OME-PIO-D96 - page 3

    OME-PIO-D96 User Manual OME-PIO-D96 User Manual (Ver.1.1, Mar/ 2003, PPH-008-11) ---- 1 ...

  • Omega Engineering OME-PIO-D96 - page 4

    Table of Contents 1. INTRODUCTION ........................................................................................................................... 3 1.1 F EATURES .................................................................................................................................... 3 1.2 S PECIFICATIONS ..................... ...

  • Omega Engineering OME-PIO-D96 - page 5

    1. Introduction The OME-PIO-D96 provides 96 TTL dig ital I/O lines. The OME-PIO-D96 consists of four 24-bit bi-directional por ts. Each 24-bit port supports three 8-bit groups PA, PB & PC. Each 8-bit group can be configured to function as either inputs or latched outputs. All groups are configured as inputs upon power-up or reset. The OME-PIO-D ...

  • Omega Engineering OME-PIO-D96 - page 6

    1.2 Specifications • All inputs are TTL compatible Logic high voltage: 2.4V (Min.) Logic low voltage: 0.8V (Max.) • All outputs are TTL compatible Sink current: 64mA (Max.) Source current: 32mA (Max.) • Environmental : Operating Temperature: 0 ° C to 60 ° C Storage Temperature: -20 ° C to 80 ° C Humidity: 0 to 90% non-condensing • Dimen ...

  • Omega Engineering OME-PIO-D96 - page 7

    1.4 PCI Data Acquisition Family We provide a family of PCI bus data acquisition cards. These cards can be divided into three groups as follows: 1. OME-PCI-series: first generation, isolated or non-isolated cards OME-PCI-1002/1202/1800/1802/1602: multi-f unction family, non-isolated OME-PCI-P16R16/P16C16/P16POR16/P8 R8: D/I/O family, isolated OME-PC ...

  • Omega Engineering OME-PIO-D96 - page 8

    2. Hardware configuration 2.1 Board Layout CN1 PCI BUS CN2 CN3 CN4 OME- PIO-D96 port0 port1 port2 port3 port4 port5 port6 port7 port8 port 9 port10 port11 OME-PIO-D96 User Manual (Ver.1.1, Mar/ 2003) ---- 6 ...

  • Omega Engineering OME-PIO-D96 - page 9

    2.2 I/O port Location There are twelve 8-bit I/O por ts in the OME-PIO-D96. Every I/O port can be programmed as D/I or D/O port. W hen the PC is first powered up, all twelve ports are used as D/I port. The I/O port location is given as follows: Connector of OME-PIO-D96 PA0 ~ PA7 PB0 ~ PB7 PC0 ~ PC7 CN1 Port0 Port1 Port2 CN2 Port3 Port4 Port5 CN3 Po ...

  • Omega Engineering OME-PIO-D96 - page 10

    2.4 D/I/O Architecture disable input Latch Clock input D/O latch CKT RESET (Sec. 3.3.1) Data (Sec. 3.3.8) D/I/O disable Buffer input Clock input D/I buffer CKT Data (Sec. 3.3.8) I/O select (Sec. 3.3.7) • The RESET is in Low-state Æ all D/I/O are disabled • The RESET is in High-state Æ all D/I/O are enabled • If D/I/O is configured as D/ ...

  • Omega Engineering OME-PIO-D96 - page 11

    2.5 Interrupt Operation All P2C0, P5C0, P8C0 and P11C0 can be us ed as interrupt signal sources. Refer to Sec. 2.1 & Sec. 2.7 for P2C0/P5C0/P8C0/P11C0 location. The interrupt of OME- PIO-D96 is level-trigger & Active_High . The interrupt signal can be inverted or non-inverted programmable. The procedures of programm ing are given as follows ...

  • Omega Engineering OME-PIO-D96 - page 12

    2.5.1 Interrupt Block Diagram of OME-PIO-D96 INT_CHAN_0 INT_CHAN_1 INT_CHAN_2 INT_CHAN_3 INT Level_trigger initial_low active_high The interrupt output signal of OME-PIO-D96, INT, is Level_trigger & Active_Low . If the INT generate a low-pulse, the OME-PIO-D96 will interrupt the PC only once. If the INT is fixed in low level, the OME-PIO-D9 ...

  • Omega Engineering OME-PIO-D96 - page 13

    2.5.2 INT_CHAN_0/1/2/3 INT_CHAN_0 (1/2/3) Inverted/Noninverted select INV0(1/2/3) Enable/Disable select EN0(1/2/3) P2C0(P5C0/P8C0/P11C0) The INT_CHAN_0(1/2/3) must be fixed in low level state normally and generated a high_pulse to interrupt the PC. The EN0 (EN1/EN2/EN3) can be used to enable/disable the INT_CHAN_0(1/2/3) as follows: (Refer to Sec. ...

  • Omega Engineering OME-PIO-D96 - page 14

    2.5.3 Initial_high, active_low Interrupt source If the P2C0 is an initial_high, active_lo w signal, the interrupt service routine should use INV0 to invert or not to i nvert the P2C0 for high_pulse generation as follows: (Refer to DEMO4.C) Initial set: now_int_state=1; /* initial state for P2C0 */ outportb(wBase+0x2a,0); /* select the inverted P2C0 ...

  • Omega Engineering OME-PIO-D96 - page 15

    2.5.4 Initial_low, active_high Interrupt source If the P2C0 is an initial_low, active_hi gh signal, the interrupt service routine should use INV0 to invert or not to i nvert the P2C0 for high_pulse generation as follows: (Refer to DEMO3.C) Initial set: now_int_state=0; /* initial state for P2C0 */ outportb(wBase+0x2a,1); /* select the non-inverted ...

  • Omega Engineering OME-PIO-D96 - page 16

    2. 5 .5 Muliti Interrupt Source Assume: P2C0 is initial Low, active High, P5C0 is initial High, active Low P8C0 is initial Low, active High P11C0 is initial High, active Low as follows: P5C0 P2C0 P8C0 P11C0 P2C0 & P5C0 are return to normal at the same time. P8C0 & P11C0 are return to normal at the same time. P2C0 & P5C0 are active at th ...

  • Omega Engineering OME-PIO-D96 - page 17

    void interrupt irq_service() { new_int_state=inportb(wBase+7)&0x0f; /* read all interrupt state */ int_c=new_int_state^now_int_state; /* compare which interrupt */ /* signal be change */ if ((int_c&0x1)!=0) /* INT_CHAN_0 is active */ { if ((new_int_state&0x01)!=0) /* now P2C0 change to high */ { CNT_H1++; } else /* now P2C0 change to lo ...

  • Omega Engineering OME-PIO-D96 - page 18

    2.6 Daughter Boards 2.6.1 OME-DB-37 The OME-DB-37 is a general purpose daughter board for D-sub 37 pins. It is designed for easy wire connection. 2.6.2 OME-DN-37 & OME-DN-50 The OME-DN-37 is a general purpose daughter board for D- sub 37 -pin connector . The OME-DN- 50 is designed for 50-pin flat-cable header. They are designed for easy wiring. ...

  • Omega Engineering OME-PIO-D96 - page 19

    2.6.4 OME-ADP-37/PCI & OME-ADP-50/PCI The OME-ADP-37/PCI & OME-ADP-50/PCI are extenders for 50-pin headers. One side of OME-ADP-37/PCI & OME-ADP-50/PCI can be connected to a 50-pin header. The other side can be mounted on the PC chassis as follows: OME-ADP-37/PCI: 50-pin header to D- sub 37 extender. OME-ADP-50/PCI: 50-pin header to 50- ...

  • Omega Engineering OME-PIO-D96 - page 20

    2.6.5 OME-DB-24P/24PD Isolated Input Board The OME-DB-24P is a 24 channel isolat ed digital input daughter board. The optically isolated inputs of the OME-DB -24P, consists of a bi-directional opto- coupler with a resistor for current sens ing. You can use the OME-DB-24P to sense DC signal from TTL levels up to 24V or us e the OME-DB-24P to sense a ...

  • Omega Engineering OME-PIO-D96 - page 21

    2.6.6 OME-DB-24R/24RD Relay Board The OME-DB-24R, 24 channel relay output board, consists of 24 form C relays for efficient switch of load by programmed c ontrol. The relays are energized by apply 12V/24V signal to the appropriated relay ch annel on the 50-pin flat connector. There are 24 enunciator LEDs for each relay and they light when their ass ...

  • Omega Engineering OME-PIO-D96 - page 22

    2.6.7 OME-DB-24PR/24POR/24C OME-DB-24PR 24*power relay, 5A/250V OME-DB-24POR 24*Photo MOS relay, 0.1A/350VAC OME-DB-24C 24*open collector, 100mA per channel, 30V max. The OME-DB-24PR, 24 channel power rela y output board, consists of 8 form C and 16 form A electromechanical relays for efficient switching of load by programmed control. The contact o ...

  • Omega Engineering OME-PIO-D96 - page 23

    2.6.8 Daughter Boards Comparison Table 20-pin flat-cable 50-pin flat-cable D-sub 37-pin OME-DB-37 No No Yes OME-DN-37 No No Yes OME-ADP-37/PCI No Yes Yes OME-ADP-50/PCI No Yes No OME-DB-24P No Yes No OME-DB-24PD No Yes Yes OME-DB-16P8R No Yes Yes OME-DB-24R No Yes No OME-DB-24RD No Yes Yes OME-DB-24C Yes Yes Yes OME-DB-24PR Yes Yes No OME-DB-24PRD ...

  • Omega Engineering OME-PIO-D96 - page 24

    2.7 Pin Assignment CN1: 37 pin of D-type female c onnector. (For Port0, Port1, Port2) Pin Number Description Pin Num ber Description 1 N. C. 20 VCC 2 N. C. 21 GND 3 P1B7 22 P2C7 4 P1B6 23 P2C6 5 P1B5 24 P2C5 6 P1B4 25 P2C4 7 P1B3 26 P2C3 8 P1B2 27 P2C2 9 P1B1 28 P2C1 10 P1B0 29 P2C0 11 GND 30 P0A7 12 N.C. 31 P0A6 13 GND 32 P0A5 14 N.C. 33 P0A4 15 G ...

  • Omega Engineering OME-PIO-D96 - page 25

    CN2/CN3/CN4: 50-pin of flat-cable connector (for Port3 ~ Port11) Pin Number Description Pin Num ber Description 1 P5C7/P8C7/P11C7 2 GND 3 P5C6/P8C6/P11C6 4 GND 5 P5C5/P8C5/P11C5 6 GND 7 P5C4/P8C4/P11C4 8 GND 9 P5C3/P8C3/P11C3 10 GND 11 P5C2/P8C2/P11C2 12 GND 13 P5C1/P8C1/P11C1 14 GND 15 P5C0/P8C0/P11C0 16 GND 17 P4B7/P7B7/P10B7 18 GND 19 P4B6/P7B6/ ...

  • Omega Engineering OME-PIO-D96 - page 26

    3. I/O Control Register 3.1 How to Find the I/O Address The plug & play BIOS will assign a prope r I/O address to every OME-PIO/PISO series card in the power-up stage. The IDs of OME-PIO -D96 cards are given as follows: • Vendor ID = E159 • Device ID = 0002 The sub IDs of OME-PIO-D96 are given as follows: • Sub-vendor ID= 80 • Sub-devic ...

  • Omega Engineering OME-PIO-D96 - page 27

    3.1.1 PIO_DriverInit PIO_DriverInit(&wBoards, wSubVendor,w SubDevice,wSubAux) • wBoards=0 to N Æ number of boards found in this PC • wSubVendor Æ subVendor ID of board to find • wSubDevice Æ subDevice ID of board to find • wSubAux Æ subAux ID of board to find This function can detect all OME-PIO/PISO series card in the system. It is ...

  • Omega Engineering OME-PIO-D96 - page 28

    OME - PIO - D96 U ser Manual ( Ver.1.1, Mar/2003) ---- 26 The Sub IDs of OME - PIO/PISO series card are given as follows: OME - PIO/PISO series card Description Sub_vendo Old (New) Sub_device Old (New) Sub_AUX OME - PIO - D144 (Rev4.0) 144 × D/I/O 80 (5C80) 01 00 O ME - PIO - D96 (Rev4.0) 96 × D/I/O 80 (5880) 01 10 OME - PIO - D64 (Rev2.0) 64 × ...

  • Omega Engineering OME-PIO-D96 - page 29

    3.1.2 PIO_GetConfigAddressSpace PIO_GetConfigAddressSpace(wBoardNo,*wBase,*w Irq, *wSubVendor, *wSubDevice,*wSubAux,*w SlotBus, *wSlotDevice) • wBoardNo=0 to N Æ totally N+1 boards found by PIO_DriveInit(….) • wBase Æ base address of the board control word • wIrq Æ allocated IRQ channel number of this board • wSubVendor Æ subVendor ID ...

  • Omega Engineering OME-PIO-D96 - page 30

    3.1.3 Show_PIO_PISO Show_PIO_PISO(wSubVendor,wSubDevice,w SubAux) • wSubVendor Æ subVendor ID of board to find • wSubDevice Æ subDevice ID of board to find • wSubAux Æ subAux ID of board to find This function will output a text string for these special subIDs. This text string is the same as that defined in PIO.H The demo program is given ...

  • Omega Engineering OME-PIO-D96 - page 31

    3.2 The Assignment of I/O Address The plug & play BIOS will assign the pr oper I/O address to PIO/PISO series card. If there is only one PIO/PISO board, the user can identify the board as card_0. If there are two PIO/PISO boards in the system, the user will be very difficult to identify which board is card_0? The soft ware driver can support 16 ...

  • Omega Engineering OME-PIO-D96 - page 32

    3.3 The I/O Address Map The I/O address of OME-PIO/PISO series card is automatically assigned by the main board ROM BIOS. The I/O address can also be re- assigned by user. It is strongly recommended not to change the I/O address by user. The plug & play BIOS will a ssign proper I/O address to each OME-PIO/PISO series card very well. The I/O add ...

  • Omega Engineering OME-PIO-D96 - page 33

    3.3.1 RESET Control Register (Read/Write): wBase+0 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Reserved Reserved Reserved Reserved Reserved Reserved Reserved RESET Note. Refer to Sec. 3.1 for more information about wBase. When the PC is first power-on, the RESET signal is in Low-state. This w ill disable all D/I/O operations. The user has to ...

  • Omega Engineering OME-PIO-D96 - page 34

    3.3.4 INT Mask Control Register (Read/Write): wBase+5 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 0 0 0 0 EN3 EN2 EN1 EN0 Note. Refer to Sec. 3.1 for more information about wBase. EN0=0 Æ disable P2C0 as a interrupt signal (default) EN0=1 Æ enable P2C0 as a interrupt signal outportb(wBase+5,0); /* disable interrupt */ outportb(wBase+5,1); /* ...

  • Omega Engineering OME-PIO-D96 - page 35

    3.3.6 Interrupt Polarity Control Register (Read/Write): wBase+0x2A Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 0 0 0 0 INV3 INV2 INV1 INV0 Note. Refer to Sec. 3.1 for more information about wBase. INV0=1 Æ select the non-inverted signal from P2C0 INV0=0 Æ select the inverted signal from P2C0 outportb(wBase+0x2a,0x0f); /* select the non-invert ...

  • Omega Engineering OME-PIO-D96 - page 36

    3.3.7 I/O Selection Control Register (Write): wBase+0xcc Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 0 0 0 0 0 Port2 Port1 Port0 (Write): wBase+0xdc Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 0 0 0 0 0 Port5 Port4 Port3 (Write): wBase+0xec Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 0 0 0 0 0 Port8 Port7 Port6 (Write): wBase+0xfc Bit 7 ...

  • Omega Engineering OME-PIO-D96 - page 37

    3.3.8 Read/Write 8-bit data Register (Read/Write):wBase+0xc0/0xc4/0xc8/0xd0/0xd4/0xd8/ 0xe0/0xe4/0xe8/0xf0/0xf4/0xf8/ Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 D7 D6 D5 D4 D3 D2 D1 D0 Note. Refer to Sec. 3.1 for more information about wBase. There are twelve 8-bit I/O port in the OME-PIO-D96. Every I/O port can be programmed as D/I or D/O por ...

  • Omega Engineering OME-PIO-D96 - page 38

    4. Demo program It is recommended to read the release note f irst. All important inform ation will be given in release note as follows: 1. Where you can find the software driver & utility? 2. How to install software & utility? 3. Where is the diagnostic program? 4. FAQ The demo programs are provided on the so ftware floppy disk or CD. After ...

  • Omega Engineering OME-PIO-D96 - page 39

    4.1 PIO_PISO /* ------------------------------------------------------------ */ /* Find all PIO_PISO series cards in this PC system */ /* step 1 : plug all PIO_PISO cards into PC */ /* step 2 : run PIO_PISO.EXE */ /* ------------------------------------------------------------ */ #include "PIO.H" WORD wBase,wIrq; WORD wBase2,wIrq2; int ma ...

  • Omega Engineering OME-PIO-D96 - page 40

    4.1.1 PIO_PISO.EXE for Windows User can find this utility in the software CD or floppy disk. It is useful for all OME-PIO/PISO series cards. After executing the utility, detailed information f or all OME-PIO/PISO cards that are installed in the PC will be shown as follows: OME-PIO-D96 User Manual (Ver.1.1, Mar/ 2003) ---- 38 ...

  • Omega Engineering OME-PIO-D96 - page 41

    4.2 DEMO1 /* demo 1 : D/O demo of CN1 */ /* step 1 : connect a OME-DB-24C to CN1 of OME-PIO-D96 */ /* step 2 : run DEMO1.EXE */ /* step 3 : check the LEDs of OME-DB-24C will turn on sequentially*/ /* -------------------------------------------------------------- */ #include "PIO.H" WORD wBase,wIrq; main() { int i1,i2,i3; long i=1; WORD wB ...

  • Omega Engineering OME-PIO-D96 - page 42

    4.3 DEMO2 /* demo 2 : DI/O demo of CN2 - CN3 */ /* step 1 : connect CN2 t0 CN3 of OME-PIO-D96 */ /* step 2 : run DEMO2.EXE */ /* step 3 : check the information on screen D/I will same as D/O */ /* -------------------------------------------------------------- */ #include "PIO.H" WORD wBase,wIrq; main() { int i1,i2,i3,j1,j2,j3; WORD wBoard ...

  • Omega Engineering OME-PIO-D96 - page 43

    4.4 DEMO3 /* demo 3 : Count high pulse of P2C0 */ /* (initial Low & active High) */ /* step 1 : run DEMO3.EXE */ /* -------------------------------------------------------------- */ #include "PIO.H" #define A1_8259 0x20 #define A2_8259 0xA0 #define EOI 0x20 WORD init_low(); WORD wBase,wIrq; static void interrupt irq_service(); int COU ...

  • Omega Engineering OME-PIO-D96 - page 44

    { irqmask=inportb(A1_8259+1); 0xfb); /* IRQ2 */ 0xff ^ (1<<(wIrq-8))); tportb(wBase+5,1); /* enable interrupt (P2C0) */ d interrupt irq_service() /* now P2C0 change to low */ rq>=8) outportb(A2_8259,0x20); outportb(A1_8259+1,irqmask & irqmask=inportb(A2_8259+1); outportb(A2_8259+1,irqmask & setvect(wIrq-8+0x70,irq_service); } ou no ...

  • Omega Engineering OME-PIO-D96 - page 45

    4.5 DEMO4 /* demo 4 : Count high pulse of P2C0 */ /* (initial High & active Low) */ /* step 1 : run DEMO4.EXE */ /* -------------------------------------------------------------- */ #include "PIO.H" #define A1_8259 0x20 #define A2_8259 0xA0 #define EOI 0x20 WORD init_high(); WORD wBase,wIrq; static void interrupt irq_service(); int CO ...

  • Omega Engineering OME-PIO-D96 - page 46

    { irqmask=inportb(A1_8259+1); 0xfb); /* IRQ2 */ 0xff ^ (1<<(wIrq-8))); tportb(wBase+5,1); /* enable interrupt (P2C0) */ d interrupt irq_service() /* now P2C0 change to low */ outportb(A1_8259+1,irqmask & irqmask=inportb(A2_8259+1); outportb(A2_8259+1,irqmask & setvect(wIrq-8+0x70,irq_service); } ou now_int_state=1; /* now ini_signal i ...

  • Omega Engineering OME-PIO-D96 - page 47

    4.6 DEMO5 /* demo 5 : Four interrupt sources */ /* P2C0 : initial Low , active High */ /* P5C0 : initial High , active Low */ /* P8C0 : initial Low , active High */ /* P11C0 : initial High , active Low */ /* step 1 : run DEMO5.EXE */ /* -------------------------------------------------------------- */ #include "PIO.H" #define A1_8259 0x20 ...

  • Omega Engineering OME-PIO-D96 - page 48

    disable(); se+5,0); /* disable all interrupt */ mask=inportb(A1_8259+1); 0xff ^ (1<<wIrq)); mask=inportb(A1_8259+1); 0xfb); /* IRQ2 */ =0x05; +0x2a,invert); /* P2C0 = non-inverte input */ -------------------------------------------------------------- */ e=inportb(wBase+7)&0x0f; now P2C0 change to high */ /* now P2C0 change to low */ 1; /* ...

  • Omega Engineering OME-PIO-D96 - page 49

    else /* now P5C0 change to low */ _L2++; =invert^2; /* generate a high pulse */ if ((new_int_state&0x04)!=0) /* now P8C0 change to high */ ((new_int_state&0x08)!=0) /* now P11C0 change to high */ 0x20); { CNT } invert } if ((int_c&0x4)!=0) { { CNT_H3++; } /* now P8C0 change to low */ else { T_L3++; CN } t=invert^4; /* generate a high pu ...

  • Omega Engineering OME-PIO-D96 - page 50

    W ARRANTY / DISCLAIMER OMEGA ENGINEERING, INC. warrants this unit to be free of defects in materials and workmanship for a period of 13 months from date of purchase. OME GA ’ s W ARRANTY adds an additional one (1) month grace period to the normal one (1) year product warranty to cover handling and shipping time. This ensures that OMEGA ’ s cust ...

  • Omega Engineering OME-PIO-D96 - page 51

    M4040/0104 Where Do I Find Ever ything I Need for Pr ocess Measurement and Control? OM EGA…Of Course! Shop online at www .omega.com TEMPERA TURE   Thermocouple, RTD & Thermistor Probes, Connectors, Panels & Assemblies   Wire: Thermocouple, RTD & Thermistor   Calibrators & Ice Point References   Recorders, C ...

Fabricant Omega Engineering Catégorie Computer Hardware

Les documents que nous recevons du fabricant de l'appareilOmega Engineering OME-PIO-D96 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Omega Engineering
- manuels d’utilisations OME-PIO-D96
- fiches produit Omega Engineering
- dépliants
- ou étiquettes-énergie Omega Engineering OME-PIO-D96
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Omega Engineering OME-PIO-D96.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Omega Engineering OME-PIO-D96, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Omega Engineering OME-PIO-D96. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Omega Engineering OME-PIO-D96.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Omega Engineering OME-PIO-D96, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Omega Engineering OME-PIO-D96 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Omega Engineering OME-PIO-D96.

Le manuel d’utilisation complet Omega Engineering, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Omega Engineering OME-PIO-D96 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Omega Engineering OME-PIO-D96, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lOmega Engineering OME-PIO-D96 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Omega Engineering OME-PIO-D96 - qui devraient nous aider dans les premières étapes lors de l'utilisation Omega Engineering OME-PIO-D96
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Omega Engineering OME-PIO-D96
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Omega Engineering OME-PIO-D96 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Omega Engineering OME-PIO-D96?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Omega Engineering OME-PIO-D96, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Omega Engineering OME-PIO-D96 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)