-
Alamo Eagle 14 - page 1
©2009 Alamo Group Inc. EAGLE 20/14 Published 03/09 Part NO. 00779092C OPERA T OR’S MANUAL ALAMO INDUSTRIAL 1502 East W alnut Seguin, T exas 78155 830-379-1480 FLEX-WING MECHANICAL LEVEL LIFT ROT AR Y MOWER This Operator' s Manual is an integral p art of the safe opera tion of this machine and must be maintaine d with the un it at all times. ...
-
Alamo Eagle 14 - page 2
T o the Owner/Operator/Dealer All implement s with moving part s are potentially hazard ous . There is no substitute for a cautio us , safe-minded operator who recognizes the potential hazards and follows reasonab le safety practices. The manufacturer has designed this impleme nt to be used with all its safety equipment properly a ttached to m inim ...
-
Alamo Eagle 14 - page 3
T able of Content s SAFETY SECTION ........................... .............................. ........................ ........1-1 General Safety Instructions and P ractices ................... ................ ................. ................ ................ . ........ ............ 1-2 Operator Safety Instructions an d Prac tices .............. ...
-
Alamo Eagle 14 - page 4
Boarding the Tractor . ...... ............. ............. ................ ............. ............. ................ ............. .. ........................... ..... 4-8 Dismounting the Tractor .. ... ... ............. ............. ............. ................ ............. ............. .............. ............ ............. ..... 4-8 S ...
-
Alamo Eagle 14 - page 5
SLIP CLUTCHES ............ ............. ................ ............. ............. ................ ............. ............. .... ...................... ...... 5-16 TIRES AND WHEELS .. ... ... ... .... ... ............. ... ... .... ............ .... ... ... ............. ... .... ... ... ............. ... ... .. ........................ 5-17 ...
-
Alamo Eagle 14 - page 6
...
-
Alamo Eagle 14 - page 7
In order to reduce accidents and enha nce the safe operation of mowers, Alamo Industrial, in cooperation with other industry manufacturers has developed the AEM/FEMA I ndustrial and Agri cultural Mower Safety Practices video and guide book. The video will familiari ze and instruct mower -tractor operators in safe practic es when using industrial an ...
-
Alamo Eagle 14 - page 8
Alamo Industrial Division is willing to provide one (1) AEM Mower Safety Practices V ideo Please Send Me: VHS Format – AEM/FEMA Mower Operator Safety V ideo DVD Format – AEM/FEMA Mower Operator Safety V ideo Mower Operator ’ s Manual AEM Mower Operator ’ s Safety Manual Requester Name Phone: Requester Address: City S tate Zip Code Mower Mod ...
-
Alamo Eagle 14 - page 9
Safety Section 1-1 © 2009 Alamo Group In c. SAFETY SECTION ...
-
Alamo Eagle 14 - page 10
SAFETY Eagle 20 03/09 Safety Section 1-2 © 2009 Alamo Group In c. SAFETY General Safety Instruct ions and Practices A careful operator is the best opera tor . Safety is of primary import ance to the manu facturer and should be to the owner/operator . Most accidents ca n be avoi ded by being a ware of your equipment, your surroundings, and observin ...
-
Alamo Eagle 14 - page 11
SAFETY Eagle 20 03/09 Safety Section 1-3 © 2009 Alamo Group In c. SAFETY Operator Safety Instr uctions and Practices Engine Exhaust, some of its constitue nts, a nd cert ain vehicle compone nts cont ain or emit chemicals known to the st ate of California to cause cancer and birth defects or oth er reproductive harm. (S G- 30 ) Battery posts, ter m ...
-
Alamo Eagle 14 - page 12
SAFETY Eagle 20 03/09 Safety Section 1-4 © 2009 Alamo Group In c. SAFETY PROLONGED EXPOSURE TO LOUD NOISE MA Y CAUSE PERMANENT HEARING LOSS! T ractors with or without an Implement attached can often be n oisy enough to cause permanent he aring loss. We recommen d that you always wear hearing protection if the noise in the Operator’s position exc ...
-
Alamo Eagle 14 - page 13
SAFETY Eagle 20 03/09 Safety Section 1-5 © 2009 Alamo Group In c. SAFETY U se ex t reme cau ti on w h en ge tti ng on t o th e I mp l emen t t o per f orm rep a i rs, ma i n t enance an d when removing accu mulated material. Only st and on solid flat surfaces to ensure good footing. Use a lad der or raised st and to access high spots which ca nnot ...
-
Alamo Eagle 14 - page 14
SAFETY Eagle 20 03/09 Safety Section 1-6 © 2009 Alamo Group In c. SAFETY Equipment Operation Safety In structions and Practices Repeated or subst antial breathing of hazardou s dusts, includin g crystalline silica, could ca use fatal or serious respiratory disease including silicosis. Concrete, maso nry , many types of rock, and various other mate ...
-
Alamo Eagle 14 - page 15
SAFETY Eagle 20 03/09 Safety Section 1-7 © 2009 Alamo Group In c. SAFETY Operate this Eq uipment only with a T ractor eq uipped with an approved ro ll- over-protectiv e system (ROP S). Always wear seat belts. Serious injury or even death could re su lt from fall ing off the tr actor --p articularly during a tu rn over when the operator could be pi ...
-
Alamo Eagle 14 - page 16
SAFETY Eagle 20 03/09 Safety Section 1-8 © 2009 Alamo Group In c. SAFETY Do not operate this Equi pment with hy draulic oil or fuel leaking. Oil and fuel are explosive and the ir presence could present a ha zard. Do not check for leaks with your hand! High-pr essure oil streams from breaks in the line co uld penetrat e the skin and cause tissue da ...
-
Alamo Eagle 14 - page 17
SAFETY Eagle 20 03/09 Safety Section 1-9 © 2009 Alamo Group In c. SAFETY There are obvio us and hidden potential h azards in the operation of th is Mower . REMEMBER! This machine is often oper ated in heavy brush and in heavy weeds. The Bla des of this Mower ca n throw objects if shields are not pro perly installed an d maintained. Se rious injury ...
-
Alamo Eagle 14 - page 18
SAFETY Eagle 20 03/09 Safety Section 1-10 © 2009 Alamo Group In c. SAFETY Follow these guidelines to reduce the risk of equipment and grass fires while operating, servicing, and rep airing the Mower and T ractor: -Equip the T ractor with a fire exti nguisher in an accesible location. -Do Not oper ate the Mower on a T ractor with an und erframe exh ...
-
Alamo Eagle 14 - page 19
SAFETY Eagle 20 03/09 Safety Section 1-11 © 2009 Alamo Group In c. SAFETY Rotary Mowers are capa ble under adverse conditions of throwing objects for great dist ances (300 feet or more) an d causing serious injury or death. Follow safety messag es carefully . STOP MOWING IF P ASSERSBY ARE WITHIN 100 Y ARDS UNLESS: -Front and Rear Deflectors, Chain ...
-
Alamo Eagle 14 - page 20
SAFETY Eagle 20 03/09 Safety Section 1-12 © 2009 Alamo Group In c. SAFETY Connecting or Disconnecting Im plement Safety Instructions and Practices DO NOT use a PTO ada pter to attach a non-matching Im plement driveline to a T ractor PTO. Use of an a dapter can double the ope rating speed of the Implemen t resulting in excessive vibration, thrown o ...
-
Alamo Eagle 14 - page 21
SAFETY Eagle 20 03/09 Safety Section 1-13 © 2009 Alamo Group In c. SAFETY T ransporting Safety Instructions and Practices Be particularly ca reful when transporting the Im ple ment with the T ractor . T urn curves or go up hills only at a low speed and using a grad ual steering angle. Rear mounted implements move the center of gravity to the rea r ...
-
Alamo Eagle 14 - page 22
SAFETY Eagle 20 03/09 Safety Section 1-14 © 2009 Alamo Group In c. SAFETY T ransport only at speeds where you can maintain con trol of the equipment. Seriou s accidents and injuries can result from o perating this equipment at high sp eeds. Unders ta nd the T ractor and Implement and how it handles before transporting on street s and high ways. Ma ...
-
Alamo Eagle 14 - page 23
SAFETY Eagle 20 03/09 Safety Section 1-15 © 2009 Alamo Group In c. SAFETY Maintenance and Service Safet y Instructions and Practices Secure the Implement for tr ansport before traveling on public ro ads. For pull-type Implement s, secure the ce nter axle using cylind er stop s or transport pi n and p roperly att ach a safety chain between the Impl ...
-
Alamo Eagle 14 - page 24
SAFETY Eagle 20 03/09 Safety Section 1-16 © 2009 Alamo Group In c. SAFETY Do not modify or alter this Implement. Do not permit anyo ne to modify or alter this Implement, any of its compon ents or any Impl ement func tion. (SG-8) Never work under the Implement, the fra mework, or any lifted component unless the Implement is securely supported o r b ...
-
Alamo Eagle 14 - page 25
SAFETY Eagle 20 03/09 Safety Section 1-17 © 2009 Alamo Group In c. SAFETY S torage and Parking Safety Instructions and Practices Concluding Safety Instr uctions and Practices Replace bent or b roken blades with new blades. NEVER A TTEMPT TO STRAIGHTEN, WELD, OR WELD HARDF ACING ON BLAD ES SINCE THIS WILL LIKEL Y CRACK OR OTHERWISE DAMAGE THE BLADE ...
-
Alamo Eagle 14 - page 26
SAFETY Eagle 20 03/09 Safety Section 1-18 © 2009 Alamo Group In c. SAFETY Decal Location NOTE: Alamo Industrial supp lies safety decals on this pr oduct to promote safe oper ation. Damage to the decals may occur while in sh ipping, use, or reconditioning. Alamo I ndustr ial cares about the safety of it s customers, operators, and bystanders, and w ...
-
Alamo Eagle 14 - page 27
SAFETY Eagle 20 03/09 Safety Section 1-19 © 2009 Alamo Group In c. SAFETY ITEM P ART NO. QTY TYPE DESCRIPTION 1. 00725746 1 PELIGRO Get Manual T ranslated 2. 00753840 2{1} DANGER Folding Wings 3. 00756004 ((3{1})) DANGER Driveline Shield Missing 4. 00756005 3{1} DANGER Rotating Dr iveline 5. 00769736 1 W ARNING Use/Repa ir Shields & Guards 6. ...
-
Alamo Eagle 14 - page 28
SAFETY Eagle 20 03/09 Safety Section 1-20 © 2009 Alamo Group In c. SAFETY Decal Description Peligro T ranslation, If yo u do not know how to read English, please find someone who knows how to read English. P/N 00725746 DANGER! S tay clear when lowering or raising wings. P/N 00753840 DANGER! Guard Missing, Do Not Oper ate. If you see this decal, Do ...
-
Alamo Eagle 14 - page 29
SAFETY Eagle 20 03/09 Safety Section 1-21 © 2009 Alamo Group In c. SAFETY W ARNING! Maintain shields and deflectors in good condition. Failure to do so may lead to injury or even death. P/N 00769736 W ARNING! Ne ver use your hand to check for oil leaks. Always use paper or cardb oa rd . P/N 00756059 DANGER! Keep Away Thrown Objects. Inspect the ar ...
-
Alamo Eagle 14 - page 30
SAFETY Eagle 20 03/09 Safety Section 1-22 © 2009 Alamo Group In c. SAFETY DANGER! Make certain that drivelines are correct length and are se curely attach ed. P/N 00756494 IMPORT ANT - Use only G enuine Alam o Industrial replacement p arts. P/N 02925100 DANGER! Keep everyone clear when lifting, folding, and working und er raised component s. Block ...
-
Alamo Eagle 14 - page 31
SAFETY Eagle 20 03/09 Safety Section 1-23 © 2009 Alamo Group In c. SAFETY W ARNING! Avoid Bodily Injur y , Use 10 00 RPM PTO S peed Only . P/N D1 14 Slow Moving V ehicle Decal. Keep SMV reflector clean and visible. DO NOT transpo rt or operate without the SM V . P/N 03200347 Red Reflector . Keep reflectors clean and visible. P/N 1458392 Amber Refl ...
-
Alamo Eagle 14 - page 32
SAFETY Eagle 20 03/09 Safety Section 1-24 © 2009 Alamo Group In c. SAFETY Operator's Manu al (with repair p arts) and warra nty was attached to this implement during final inspection. P/N 00763977 IMPORT ANT! Required For Jackshaft Unit. Suggested for standa rd shaft. P/N D102 Blade Rotation Counter Clockwise. P/N D137 Blade Rotation Clockwis ...
-
Alamo Eagle 14 - page 33
SAFETY Eagle 20 03/09 Safety Section 1-25 © 2009 Alamo Group In c. SAFETY NAME LO GO - Alamo Industrial P/N 02960766 Name LOG O - Alamo In dustrial P/N 00757139 NAME LOGO - EAGLE 20 EAGLE 20 NAME LOGO - EAGLE 14 EAGLE 14 ...
-
Alamo Eagle 14 - page 34
SAFETY Eagle 20 03/09 Safety Section 1-26 © 2009 Alamo Group In c. SAFETY INFORMA TION - 5 Y ear Gearbox W arranty P/N 00771283 Read Operato r ’s Manua l! The operator’s manual is located inside this canister . If the manual is missing order one from you r dealer . P/N 00776031 ...
-
Alamo Eagle 14 - page 35
SAFETY Eagle 20 03/09 Safety Section 1-27 © 2009 Alamo Group In c. SAFETY Multi Hazard Decal Sheet P/N 007491 17 ...
-
Alamo Eagle 14 - page 36
SAFETY Eagle 20 03/09 Safety Section 1-28 © 2009 Alamo Group In c. SAFETY PELIGRO! S panish T ranslati on for Driveline Safety P/N 00773723 W ARNING! DO NOT transport at spe eds higher than 20 mph. Only transport behind a pro perly sized and equipped tractor . P/N 00777394 W ARNING! Explosion Hazard - Release all air pressure in tire befo re loose ...
-
Alamo Eagle 14 - page 37
SAFETY Eagle 20 03/09 Safety Section 1-29 © 2009 Alamo Group In c. SAFETY Federal Laws and Regulations This section is intend ed to explain in br oad terms the co ncept and effect of federal la ws and regulations concerning employe r and employee equipme nt operat ors. This section is not intend ed as a legal interpretation of the law an d should ...
-
Alamo Eagle 14 - page 38
...
-
Alamo Eagle 14 - page 39
...
-
Alamo Eagle 14 - page 40
...
-
Alamo Eagle 14 - page 41
...
-
Alamo Eagle 14 - page 42
...
-
Alamo Eagle 14 - page 43
...
-
Alamo Eagle 14 - page 44
...
-
Alamo Eagle 14 - page 45
...
-
Alamo Eagle 14 - page 46
...
-
Alamo Eagle 14 - page 47
...
-
Alamo Eagle 14 - page 48
...
-
Alamo Eagle 14 - page 49
...
-
Alamo Eagle 14 - page 50
...
-
Alamo Eagle 14 - page 51
...
-
Alamo Eagle 14 - page 52
...
-
Alamo Eagle 14 - page 53
...
-
Alamo Eagle 14 - page 54
...
-
Alamo Eagle 14 - page 55
...
-
Alamo Eagle 14 - page 56
...
-
Alamo Eagle 14 - page 57
...
-
Alamo Eagle 14 - page 58
...
-
Alamo Eagle 14 - page 59
...
-
Alamo Eagle 14 - page 60
...
-
Alamo Eagle 14 - page 61
...
-
Alamo Eagle 14 - page 62
...
-
Alamo Eagle 14 - page 63
...
-
Alamo Eagle 14 - page 64
...
-
Alamo Eagle 14 - page 65
...
-
Alamo Eagle 14 - page 66
...
-
Alamo Eagle 14 - page 67
...
-
Alamo Eagle 14 - page 68
...
-
Alamo Eagle 14 - page 69
...
-
Alamo Eagle 14 - page 70
...
-
Alamo Eagle 14 - page 71
...
-
Alamo Eagle 14 - page 72
...
-
Alamo Eagle 14 - page 73
...
-
Alamo Eagle 14 - page 74
...
-
Alamo Eagle 14 - page 75
...
-
Alamo Eagle 14 - page 76
...
-
Alamo Eagle 14 - page 77
...
-
Alamo Eagle 14 - page 78
...
-
Alamo Eagle 14 - page 79
...
-
Alamo Eagle 14 - page 80
...
-
Alamo Eagle 14 - page 81
...
-
Alamo Eagle 14 - page 82
...
-
Alamo Eagle 14 - page 83
Introduction Section 2-1 © 2009 Alamo Group Inc. INTRODUCTION SECTION ...
-
Alamo Eagle 14 - page 84
INTRODUCTION Eagle 20 03/09 Introduction Section 2-2 © 2009 Alamo Group Inc. INTRODUCTION This Rotary Mower is designed with care and built with quality materials by skilled worker s. Proper assembly , maintenance, and ope rating practices, as described in this manual, will help t he owner/operator get years of satisfactory service from the machin ...
-
Alamo Eagle 14 - page 85
INTRODUCTION Eagle 20 03/09 Introduction Section 2-3 © 2009 Alamo Group Inc. INTRODUCTION Y our Eagle 20 is a heavy- duty Cutter/Shredder designed pr imarily for weed and grass co ntrol, brush up to 2" diameter , and shredding row cr ops such as cotton a nd corn stalks. With proper ma intenance as described in this manual, your Cutter will pr ...
-
Alamo Eagle 14 - page 86
INTRODUCTION Eagle 20 03/09 Introduction Section 2-4 © 2009 Alamo Group Inc. INTRODUCTION Attention Owner/Operator BEFORE OPERA TING THIS MACHINE: 1. Carefully read the Operator’s Manual, completely understand the Safety Messages and instructions, and know how to operate correctly both the tractor and implement. 2. Fill out the Warranty Card in ...
-
Alamo Eagle 14 - page 87
Assembly Section 3-1 © 2009 Alamo Group Inc. ASSEMBL Y SECTION ...
-
Alamo Eagle 14 - page 88
ASSEMBLY Eagle 20 03/09 Assembly Section 3-2 © 2009 Alamo Group Inc. ASSEMBL Y General Assemby Set up cutter as rece ived from factory with these in structions. Refer to Parts Listing Section for further information when necessary Select a suitable working a rea. Open parts box and lay out part s to make location ea sy . Refer to parts listing and ...
-
Alamo Eagle 14 - page 89
ASSEMBLY Eagle 20 03/09 Assembly Section 3-3 © 2009 Alamo Group Inc. ASSEMBL Y T o ngue Attachment T o assemble the tongue (FIGURE Asm-R-0013) . Align the lugs of the tongue with the top holes of th e mainframe hitch plate (1). Insert the pivot pin (2) and fasten with 2 - 1/2" x 1 1/4" bolt (3) and 1/2 " locknut (4). T o assemble th ...
-
Alamo Eagle 14 - page 90
ASSEMBLY Eagle 20 03/09 Assembly Section 3-4 © 2009 Alamo Group Inc. ASSEMBL Y Wing Section Att achements While the Center Section is still solidly blocked, attach th e Wing Sectio ns (1 ) in the horizont al plane. Using Hinge Pins (2), a ttach the Right an d Left Wing Sections to the Center Sections. NOTE: Wing Sections may require slight lifting ...
-
Alamo Eagle 14 - page 91
ASSEMBLY Eagle 20 03/09 Assembly Section 3-5 © 2009 Alamo Group Inc. ASSEMBL Y Center Section Level Lif t Axle Att achme nt (Figure Asm-R-0017 ) Attach the Center Level Lif t Axle (1) to the Ce nter Section (2) with the Center Pins (3), Bolts (4), and Nuts (5). The Wing Level Lif t Axles (6,7) ar e attached to the Wing Sections (8,9) with the Wing ...
-
Alamo Eagle 14 - page 92
ASSEMBLY Eagle 20 03/09 Assembly Section 3-6 © 2009 Alamo Group Inc. ASSEMBL Y Axle Adjustment Rod Att achment Attach the Axle Adjustm ent Rod w/Bushings (1) to the Center Axle (2) and Wing Axle (3) with bolt s an d locknuts (4). Install S pacers (5) as shown. FIGURE Asm-R-0018. Center Axle Hydraulic Cylinder Att achment Install the clevis rod end ...
-
Alamo Eagle 14 - page 93
ASSEMBLY Eagle 20 03/09 Assembly Section 3-7 © 2009 Alamo Group Inc. ASSEMBL Y TIRES AND WHEELS Before installing any tires and wheel s make cert ain the Cutter is jack ed up high enough and is securely supported. When installing a segmented or Airplane tire, be sure the flat side of the lug nut is against the Wheel. When installing a implement ti ...
-
Alamo Eagle 14 - page 94
ASSEMBLY Eagle 20 03/09 Assembly Section 3-8 © 2009 Alamo Group Inc. ASSEMBL Y Rubber S top Att achment The S pring S top is assembled to the stop bra cket (1) with the 1/2 x 5 1 /2 capscrew (2) inserte d thru the stop (3) , sp ring (4) and locknut (5). Image AsmP-R-0006. Baffle Kit Assembly (Optional) The Center Baf fle (2) is att ached to the Ce ...
-
Alamo Eagle 14 - page 95
ASSEMBLY Eagle 20 03/09 Assembly Section 3-9 © 2009 Alamo Group Inc. ASSEMBL Y Rubber Deflectors (S t andard) Attach the Center F ro nt De fle cto r B ar s(2 ) an d Ce nte r Se ctio n Def l ec to rs( 1) to th e Ce nt er Se ctio n with th e bo lts (5) Flatwa sher (6) and Locknut(8). (FIGURE Asm-R- 0059) . Attach the Front Wing Deflector Bars(3) and ...
-
Alamo Eagle 14 - page 96
ASSEMBLY Eagle 20 03 /09 Assembly Section 3-10 © 2009 Alamo Group Inc. ASSEMBL Y Chain Guard Att achment CHAIN GUARDS: Front an d Rear Chain Guar ds (Optional Equipment at extr a cost) are recommended for higher than normal usage (1 00 hours or more per y ear ) and will provide pr otection from thrown objects with careful operation. Chain Gua rds ...
-
Alamo Eagle 14 - page 97
ASSEMBLY Eagle 20 03/09 A ssembly Section 3-11 © 2009 Alamo Group Inc. ASSEMBL Y Counterweight Att achment For the two section cutter the Counter weight Attachment (1) m ust be installed to the left sid e of the Center Section with the Hinge Pin and Retaining Pin (Follo w the Wing Attachment in this section). Fill the Counterweight completely FULL ...
-
Alamo Eagle 14 - page 98
ASSEMBLY Eagle 20 03 /09 Assembly Section 3-12 © 2009 Alamo Group Inc. ASSEMBL Y Driveline Clamp Cone Y o ke Operating Instructions Loosen the yoke clamp cone with a 1 1/16” (17mm) wrench and remove the cone from yoke. Slide yoke onto the shaf t and align hole for clamping con e with annular groove of gearbox shaf t. Reinsta ll cone and tighten ...
-
Alamo Eagle 14 - page 99
ASSEMBLY Eagle 20 03/09 A ssembly Section 3-13 © 2009 Alamo Group Inc. ASSEMBL Y Three S pool Control V alve Inst allation A Three-S pool Control V alve is available from your dealer for use with tractors having eith er an open or closed center Hydraulic System. If a 3 spool valve bank is re quired assem ble on br ac ket and install on trac tor fe ...
-
Alamo Eagle 14 - page 100
...
-
Alamo Eagle 14 - page 101
Operation Sec tio n 4- 1 © 2009 Alamo Group Inc. OPERA TION SECTION ...
-
Alamo Eagle 14 - page 102
OPERATION Eagle 20 03/09 Operation Section 4-2 © 2009 Alamo Group Inc. OPERA TION ALAMO INDUSTRIAL EAGLE 20/14 ROT AR Y MOWER OPERA T ION INSTRUCTIONS Alamo Industrial Eagle 2 0/14 rotary mowe rs are manufactured with quality ma terial by skill ed workers. These mowers are designed to cu t grass, weeds, small brush and othe r vegetative material u ...
-
Alamo Eagle 14 - page 103
OPERATION Eagle 20 03/09 Operation Section 4-3 © 2009 Alamo Group In c. OPERA TION 1. St andard Equipment and S pecifications Eagle 20 Eagle 14 Cutting Width 240” 162” T ransport Width 1 15” 106” Overall W idth 248” 170” Overall Lenth 216” 216” Cutting Hei g h t 2”-14-3/4” 2”-14-3/4” Hitch Pull Pull Blade Overlap 6” 6” ...
-
Alamo Eagle 14 - page 104
OPERATION Eagle 20 03/09 Operation Section 4-4 © 2009 Alamo Group Inc. OPERA TION TRACTOR REQUIREMENTS The tractor used to oper ate the mower must have the powe r capacity to lif t, pull, and operate the Power T ake Off ( PTO) at the mower ’s rated speed wh ile traveling at a g round speed between 2 and 5 MPH. Operatin g the 2. OPERA TOR REQUIRE ...
-
Alamo Eagle 14 - page 105
OPERATION Eagle 20 03/09 Operation Section 4-5 © 2009 Alamo Group In c. OPERA TION mower with a tractor th at does not meet the followin g requirement s may cause tractor or mower damage and be a potential danger to the operator and p assersby . T ractor Requirement s and Cap abilities • ASAE approved Roll-Over Prot ective S tructure (ROPS) or R ...
-
Alamo Eagle 14 - page 106
OPERATION Eagle 20 03/09 Operation Section 4-6 © 2009 Alamo Group Inc. OPERA TION 2.3 T ractor Horsepower The horsepower re quired to operate the mower dep ends on several op erating fa ctors includ ing the vege tation to be cut, terrain condition, oper ator experience, cond ition of the mower and tractor , and others. For most mowing conditions, ...
-
Alamo Eagle 14 - page 107
OPERATION Eagle 20 03/09 Operation Section 4-7 © 2009 Alamo Group In c. OPERA TION 2.5 T ractor Hydraulics The mower center section and each wing ar e positioned with hydraulic cylin ders t hat are operated by the tractor hydr aulic pump. The tractor must have a minim um of 2 hydraulic cont rol valves devoted to the mower unless the tractor is fit ...
-
Alamo Eagle 14 - page 108
OPERATION Eagle 20 03/09 Operation Section 4-8 © 2009 Alamo Group Inc. OPERA TION 3. GETTING ON AND OFF THE TRACT OR Before getting onto the tr actor , the operator must read and completely underst and the implement and tractor operator manuals. If any p art of either manual is n o t completely understood, consult an au thorized dealer for a compl ...
-
Alamo Eagle 14 - page 109
OPERATION Eagle 20 03/09 Operation Section 4-9 © 2009 Alamo Group In c. OPERA TION BEFORE leaving the tractor seat, always engage the brake and/or set the tractor transmission in parking ge ar , disengage the PTO, stop the engine, remove the key , and wait for all moving part s to stop. Place the tractor shift lever into a low range or par king ge ...
-
Alamo Eagle 14 - page 110
OPERATION Eagle 20 03/09 Operation Sectio n 4-10 © 2009 Alamo Group Inc. OPERA TION 5.1 Connecting the Mowe r T ongue to the T ractor 1. Ensure the tractor is eq uipped wi th the corr ect PTO shaf t and the drawbar is set at the correct length. 2. Using the p arking jack, pos ition the tongue clevis to the height of the tractor dra wbar . Adjust t ...
-
Alamo Eagle 14 - page 111
OPERATION Eagle 20 03/09 Operation Sectio n 4-11 © 2009 Alamo Group In c. OPERA TION 5.2 Connecting Mower Hydrau lic Lines to the T ractor With the tract or shut down a nd secured in position, re li eve hydrau lic pressure from the tractor by moving the control levers back an d forth several times or placing the levers in the float position. When ...
-
Alamo Eagle 14 - page 112
OPERATION Eagle 20 03/09 Operation Sectio n 4-12 © 2009 Alamo Group Inc. OPERA TION T o activate the 3-spool hydraulic control valve, tie the tractor’s hydraulic control lever back to kee p hydraulic oil continuously fed to the valve bank. Hydraulic Line Support After conne cting the mower hydraulic lines to the tr actor , support the hoses with ...
-
Alamo Eagle 14 - page 113
OPERATION Eagle 20 03/09 Operation Sectio n 4-13 © 2009 Alamo Group In c. OPERA TION 6.1 Setting Deck Height LEVELING DECK CENTER SECTION 1. Place the tractor and mower o n a level su rface and lower b oth wings. 2. Use the center section hydraulic cylinder to set the mower at approxima tely 3/4 ” above the desired cutting height. The addition a ...
-
Alamo Eagle 14 - page 114
OPERATION Eagle 20 03/09 Operation Sectio n 4-14 © 2009 Alamo Group Inc. OPERA TION 6.3 Lowest Cutting Height NOTE: Only operate in the lower position wh en you are mowing in an agricultural application, be sure there are no byst anders, passerby or livestock with in 300 feet. . T o achieve the lowest possible cutting height, raise the side skirt ...
-
Alamo Eagle 14 - page 115
OPERATION Eagle 20 03/09 Operation Sectio n 4-15 © 2009 Alamo Group In c. OPERA TION Also raise both skid shoe s from the lower holes to the upper holes as shown in Figure Op-2 46 . NOTE: Change height back to normal position before operating or mowing on roadside , ditches or greenbelt s Rotary Mowers are capa ble under adverse conditions of thro ...
-
Alamo Eagle 14 - page 116
OPERATION Eagle 20 03/09 Operation Sectio n 4-16 © 2009 Alamo Group Inc. OPERA TION 7.1 Driveline Length Check When fitting the mower to the tracto r , the telescoping driveline must be inspected to ensure that at its mo st compressed position, the shafts do not “bottom out”, and whe n at its farthest exte nded postion, there is sufficie nt en ...
-
Alamo Eagle 14 - page 117
OPERATION Eagle 20 03/09 Operation Sectio n 4-17 © 2009 Alamo Group In c. OPERA TION “B o tt om i ng O u t” Ch ec k P roce d ure • Disconnect driveline from the tractor and slide the profiles together u ntil fully comp ressed. • Place a mark on the inner shield 1/8” from the end of the outer shield. • Reattach the dr iveline to the PTO ...
-
Alamo Eagle 14 - page 118
OPERATION Eagle 20 03/09 Operation Sectio n 4-18 © 2009 Alamo Group Inc. OPERA TION 7.2 Constant V elocity (CV) Driv eline For mowers equipped with a Co nst ant V elocity (CV) dr iveline, the maximum turning an gle betwe en the tractor and mower must be determined to ensure the jo int angle does not over-extend which can cause CV joint damage. Con ...
-
Alamo Eagle 14 - page 119
OPERATION Eagle 20 03/09 Operation Sectio n 4-19 © 2009 Alamo Group In c. OPERA TION Do not turn so sharp or lif t mo wer so high to produce a severe "knocking" of the Driveline which will cause accelerated wear and breakage of drive train components and could result in possible injury from the separated Driveline sections. (SRM-0 4) 8. ...
-
Alamo Eagle 14 - page 120
OPERATION Eagle 20 03/09 Operation Sectio n 4-20 © 2009 Alamo Group Inc. OPERA TION 8.1 T ractor Pre-Operation Inspection/Service Refer to the tr actor operator ’s ma nual to ensure a complete pre-operation inspection and scheduled service is performed accordi ng to the manufacturers recommenda tions. The following are some of the items that req ...
-
Alamo Eagle 14 - page 121
OPERATION Eagle 20 03/09 Operation Sectio n 4-21 © 2009 Alamo Group In c. OPERA TION The operator’s manual and safety signs af fixed on the unit contain important instru ctions on the saf e and proper use of the equipme nt. Maint ain these importan t safety features on the implement in good condition to ensure the information is available to the ...
-
Alamo Eagle 14 - page 122
OPERATION Eagle 20 03/09 Operation Sectio n 4-22 © 2009 Alamo Group Inc. OPERA TION • Ensure the tractor PT O master shield is in place, lowered and in go od condition. • Ensure each mower slip clutch shield is secured in place and in good condition. • Ensure the driveline slip clutche s are properly adjusted and the friction plates are not ...
-
Alamo Eagle 14 - page 123
OPERATION Eagle 20 03/09 Operation Sectio n 4-23 © 2009 Alamo Group In c. OPERA TION • Ensure each hydraulic cylinder is inst alled and retained co rr ectly . Ensure the proper size p ins are used to ret ain the cylinders in place and are secured with pins. • Check for hydraulic oil leaks on the cylin ders, along the hydraulic line s , and at ...
-
Alamo Eagle 14 - page 124
OPERATION Eagle 20 03/09 Operation Sectio n 4-24 © 2009 Alamo Group Inc. OPERA TION 8.3 C utting C omponent Inspection Inspect blade p an and blade assembly for the following: OPS-U-0031 ...
-
Alamo Eagle 14 - page 125
OPERATION Eagle 20 03/09 Operation Sectio n 4-25 © 2009 Alamo Group In c. OPERA TION Inspect the Blades daily for abnormal wear . REPLACE BOTH BLA D ES on that carrier IMMEDIA TEL Y if either blade has: • Become bent or deformed from it’ s original sh ape or • Any cracks are visib l e, or • Deep gouges in the blad e’s surface are pe rsen ...
-
Alamo Eagle 14 - page 126
OPERATION Eagle 20 03/09 Operation Sectio n 4-26 © 2009 Alamo Group Inc. OPERA TION 8.4 Blade Bolt Inspection Inspect Blade Bolt Head da ily for wear as followed: Inspect the Blade Bolt Heads d aily for abn ormal wear . REPLACE BOTH BLADE BOL TS on the Blades IMMEDIA TEL Y if either blade bolts has: • Visible cracks or • If the reces sed area ...
-
Alamo Eagle 14 - page 127
OPERATION Eagle 20 03/09 Operation Sectio n 4-27 © 2009 Alamo Group In c. OPERA TION T r actor PRE-OPERA T ION Inspection Mower ID# ________________ Make ____________________ Date: ________________ Shift ____________________ Before conducting the inspection, make sur e the tractor engine is off, all rotation has stopped and the tractor is in park ...
-
Alamo Eagle 14 - page 128
OPERATION Eagle 20 03/09 Operation Sectio n 4-28 © 2009 Alamo Group Inc. OPERA TION Rotary Mower PRE-OPERA T ION Inspection Mower ID# ________________ Make ____________________ Date: ________________ Shift ____________________ Before conducting the inspection, make sur e the tractor engine is off, all rotation has stopped and the tractor is in par ...
-
Alamo Eagle 14 - page 129
OPERATION Eagle 20 03/09 Operation Sectio n 4-29 © 2009 Alamo Group In c. OPERA TION 9. DRIVING THE TRACTO R AND IMPLEMENT Safe tractor transport req uires the operator possess a thoroug h knowledge of the model being ope rated and precautions to t ake while driving with an att ached implem ent. Ensure the tractor has the capacity to handle the we ...
-
Alamo Eagle 14 - page 130
OPERATION Eagle 20 03/09 Operation Sectio n 4-30 © 2009 Alamo Group Inc. OPERA TION 9.1 St arting the T ractor The procedure to st art the tractor is model specific. Refer to the tractor operator’s manual for st arting procedures for your p articular tractor . Consult an authorized dealer if the st arting procedure is unclear . Ensure the 3-poin ...
-
Alamo Eagle 14 - page 131
OPERATION Eagle 20 03/09 Operation Sectio n 4-31 © 2009 Alamo Group In c. OPERA TION T ransport Position T o raise mower wings, drive the unit to a level area and retrac t the wing hy draulic cylinde rs. DO NOT raise wings with the mo wer positioned on a n embankment or other inclined position to prevent overturning the mower . After the wings are ...
-
Alamo Eagle 14 - page 132
OPERATION Eagle 20 03/09 Operation Sectio n 4-32 © 2009 Alamo Group Inc. OPERA TION 9.4 Driving the T r actor and Cutter S tart off driving at a slow speed and gradually increase your speed while maintaining complete contro l of the tractor and mower . Moving slowly at first will also pr ev ent the tractor from rear ing up and loss of steering con ...
-
Alamo Eagle 14 - page 133
OPERATION Eagle 20 03/09 Operation Sectio n 4-33 © 2009 Alamo Group In c. OPERA TION 9.5 Crossing Ditches and Steep Inclines When crossing ditches with steep banks o r going up sharp inclines, it is possib le that the main driveline inner profile will pene trate into the outer housing to its maximum depth until the assembly be comes solid (driveli ...
-
Alamo Eagle 14 - page 134
OPERATION Eagle 20 03/09 Operation Sectio n 4-34 © 2009 Alamo Group Inc. OPERA TION Inclines and ditches should be app roached along a line which is at an an gle as shown. This type of path will reduce the possib ility of over-collapse of the driveline and re sulting damag e. If the gradient is so steep that such an approach increase s the possibi ...
-
Alamo Eagle 14 - page 135
OPERATION Eagle 20 03/09 Operation Sectio n 4-35 © 2009 Alamo Group In c. OPERA TION M any var i e d o bj ec t s, suc h as w i re, ca bl e, rope, or c h a i ns, can b ecome en t ang l e d i n th e operating p arts of the m ower head. These items could th en swing outside the hou sing at greater velocities than the blad es. Such a situation is extr ...
-
Alamo Eagle 14 - page 136
OPERATION Eagle 20 03/09 Operation Sectio n 4-36 © 2009 Alamo Group Inc. OPERA TION Rotary Mowers are capa ble under adverse conditions of throwing objects for great dist ances (300 feet or more) an d causing serious injury or death. Follow safety messag es carefully . STOP MOWING IF P ASSERSBY AR E WITHIN 100 Y ARDS UNLESS: -Front and Rear Deflec ...
-
Alamo Eagle 14 - page 137
OPERATION Eagle 20 03/09 Operation Sectio n 4-37 © 2009 Alamo Group In c. OPERA TION 10.4 PT O RPM and Ground Speed Ground speed for mowing will depend upon the height, type , and density of vege tation to be cut. Recommended speed for ef ficient mower performance is between 2 and 5 mph(3-8 kp h). Oper ate the mower at its full rated PTO speed to ...
-
Alamo Eagle 14 - page 138
OPERATION Eagle 20 03/09 Operation Sectio n 4-38 © 2009 Alamo Group Inc. OPERA TION Do not mow with two machines in the same ar ea except with Cab tractors with the wind ows closed. (SGM-1 1) Mow only in conditions where y ou have clear visibility in daylight or with adequate artificial lighting. Never mow in darkness o r foggy cond itions where y ...
-
Alamo Eagle 14 - page 139
OPERATION Eagle 20 03/09 Operation Sectio n 4-39 © 2009 Alamo Group In c. OPERA TION When you get to the end of a p ass, sligh tly raise the mower (2-4 ”) before turning. Never r aise the mower entirely while the blades are turning. If the mower must be r aised higher than 12” from ground level, disengage the tractor PT O and wait for all mowe ...
-
Alamo Eagle 14 - page 140
OPERATION Eagle 20 03/09 Operation Sectio n 4-40 © 2009 Alamo Group Inc. OPERA TION When mowing across une ven areas such as road shoulde rs, ditch e dges, and other uneven te rrain, position mower so that one suppor t wheel is near the highest po int to prevent blades from cutting into gr avel or dirt which can cause rapid bla de wear and extreme ...
-
Alamo Eagle 14 - page 141
OPERATION Eagle 20 03/09 Operation Sectio n 4-41 © 2009 Alamo Group In c. OPERA TION 10.6 S hutting Down the Implement T o shut down attached mower head, first bring the tractor to a complete s t op. Decrease engine RPM to idle then dise ngage cutterhe ad. Th e mower head will come to a complete stop within a suitable amount of time. Do not engage ...
-
Alamo Eagle 14 - page 142
OPERATION Eagle 20 03/09 Operation Sectio n 4-42 © 2009 Alamo Group Inc. OPERA TION Never unhitch without using the T ongue Jack. The T ongue is very hea vy . Attempting to lif t the T ongue without using the T ongue Jack could ca use stra ins or other injury . Allowing the tongue to fall sudden ly and unexpectedly coul d result in crushi ng injur ...
-
Alamo Eagle 14 - page 143
OPERATION Eagle 20 03/09 Operation Sectio n 4-43 © 2009 Alamo Group In c. OPERA TION 12. MOWER STORAGE It is recommended that the mower be stored with the c enter section and both wings fully lowered to g round level. If the mower is stored with the wings in the raised position, select a level area and inst all wing transport braces to prevent the ...
-
Alamo Eagle 14 - page 144
OPERATION Eagle 20 03/09 Operation Sectio n 4-44 © 2009 Alamo Group Inc. OPERA TION Never allow children or other persons to ride on the T ractor or Implement. Falling off can result in serious injury or death. (SG-1 0) Before transporting th e tractor and mower , idle the tractor engine, d isengage the PTO and wait for all mower moving parts to c ...
-
Alamo Eagle 14 - page 145
OPERATION Eagle 20 03/09 Operation Sectio n 4-45 © 2009 Alamo Group In c. OPERA TION 13.1 Tire and Wheels Laminated Sectional T ires are designe d for conditions where puncture p roof performance is required and the mower will not be transporte d for long distances on roadways. Tran sport speed for laminated tires should not exceed 20 MPH. Excessi ...
-
Alamo Eagle 14 - page 146
OPERATION Eagle 20 03/09 Operation Sectio n 4-46 © 2009 Alamo Group Inc. OPERA TION Never allow children or other persons to ride on the T ractor or Implement. Falling off can result in serious injury or death. (SG-1 0) Make cert ain that the “Slow Moving V ehicle” (SMV) sign is installed in such a wa y as to be clearly visible and legible. Wh ...
-
Alamo Eagle 14 - page 147
OPERATION Eagle 20 03/09 Operation Sectio n 4-47 © 2009 Alamo Group In c. OPERA TION When operating on public roads, have consideration for other road u sers. Pull to the side of the road occasionally to allow all following traffic to pass. Do not exceed the legal sp eed limit set in your country for agricultural tra ctors. Always stay alert when ...
-
Alamo Eagle 14 - page 148
OPERATION Eagle 20 03/09 Operation Sectio n 4-48 © 2009 Alamo Group Inc. OPERA TION Use adequately sized and rated traile rs and equipment to transport the tractor and imp lement. Consult an author ized dealer to determine the pr oper equipment required. Using a dequately sized chains, heavy duty straps , cables and/or binders, securely tie down b ...
-
Alamo Eagle 14 - page 149
OPERATION Eagle 20 03/09 Operation Sectio n 4-49 © 2009 Alamo Group In c. OPERA TION 14. TROUBLE SH OOTING GUIDE Problem Possible Cause Remedy Excessive Vi brations Check Gear box bolt s. T ighten if loose. Check For loose nuts on T ighten If loose bladeholder and blades Check for bent output shaf t. Replace sha ft if bent. If shaft is bent oil wi ...
-
Alamo Eagle 14 - page 150
OPERATION Eagle 20 03/09 Operation Sectio n 4-50 © 2009 Alamo Group Inc. OPERA TION Clutch Slips Excessively Clutc h linings badly wor n or Repair clutch per ma in te na nc e plates warped . section of man ua ls. T oo much power for clutch. Reduce ground speed and material intake. Oil on facings. Replace facings. Friction facings glazed. Clean wit ...
-
Alamo Eagle 14 - page 151
Maintenanc e Sec tio n 5- 1 © 2009 Alamo Group Inc. MAINTENANCE SECTION ...
-
Alamo Eagle 14 - page 152
MAINTENANCE Eagle 20 03/09 Maintenance Section 5-2 © 2009 Alamo Group Inc. MAINTENANCE Before operat ing your Rotary Cutt er , m ake sure it is properly lubricated and thor oughly inspecte d. Only a minimum of time and effort is req uired to regularl y lubr icate and maint ain this machine to provide long life and trouble free oper ation. Always d ...
-
Alamo Eagle 14 - page 153
MAINTENANCE Eagle 20 03/09 Maintenance Section 5-3 © 2009 Alamo Group Inc. MAINTENANCE ...
-
Alamo Eagle 14 - page 154
MAINTENANCE Eagle 20 03/09 Maintenance Section 5-4 © 2009 Alamo Group Inc. MAINTENANCE T o ngue The T ongue Hitch Pins att ach the T ongue to the Cen ter Section and should be ch ecked for signs of wear or cracking. Replace as needed. The Dr awbar 1” bol t faste ns th e cutter to the tra ctor Drawb ar . When the cutter is unhitched and this 1” ...
-
Alamo Eagle 14 - page 155
MAINTENANCE Eagle 20 03/09 Maintenance Section 5-5 © 2009 Alamo Group Inc. MAINTENANCE DIVIDER GEARBOX The T est Plug for the Divider Gearbox is located on the right side of the in put shaft. The f iller pressure relief Plug is on top of the Gearbox. FIGURE MntP-R-0005. Do not over-fill. If Gearboxes are filled ab ove T est Plug Level, pr essure u ...
-
Alamo Eagle 14 - page 156
MAINTENANCE Eagle 20 03/09 Maintenance Section 5-6 © 2009 Alamo Group Inc. MAINTENANCE DRIVELINES The Drivelines and U-Joint s should be inspected each morn ing before the Cutter is started. FIGURE MntP- R-0006 and Mnt-R- 0031. The U-Joint and CV Joint on the Driveline unde rgo extreme forces wh en the unit is turning or wh en the Wings are being ...
-
Alamo Eagle 14 - page 157
MAINTENANCE Eagle 20 03/09 Maintenance Section 5-7 © 2009 Alamo Group Inc. MAINTENANCE MAIN CV DRIVELINE SAFETY SHIELD (FIGURE Mnt-R-0032) T o remove the outer CV cone, remove the locking screws from shield cone. Remove cone over yo ke. MNT-R- 0038. Remove bearing r ing and remove the lo cking screws from inner shield cone. Mnt-R-0038. T urn inner ...
-
Alamo Eagle 14 - page 158
MAINTENANCE Eagle 20 03/09 Maintenance Section 5-8 © 2009 Alamo Group Inc. MAINTENANCE WING DRIVELINE Figure MntP-R-001 1) Remove the two shield bearings per ha lf shaft by prying the head of the bearings up with a screwdri ver , and pulling them out with pliers. Figure MntP-R-0012) Grasp th e Y oke and shield tube and pull shaft from the shield. ...
-
Alamo Eagle 14 - page 159
MAINTENANCE Eagle 20 03/09 Maintenance Section 5-9 © 2009 Alamo Group Inc. MAINTENANCE Figure MntP-R-0014) Grea se and install the sleeve baring in groove at th e end of the sleeve (only on one half shaft) . Figure Mnt P-R-0015 ) Slide the shield tube assembly over the shaf t, so that the bearing holes in the shield align with t he shield b ear in ...
-
Alamo Eagle 14 - page 160
MAINTENANCE Eagle 20 03/09 Maintenance Section 5-10 © 2009 Alamo Group Inc. MAINTENANCE T O DISASSEMBLE UNIVERSAL JOINT 1. Remove all snap ring s. 2. Position joint in loose vice, strike top arm of unsupported yoke to drive the top cup up. Repeat on oppo site side. 3. If you cannot grip the loosene d cap per S te p 4, use a poin te d too l to tip ...
-
Alamo Eagle 14 - page 161
MAINTENANCE Eagle 20 03/09 Maintenance Section 5-11 © 2009 Alamo Group Inc. MAINTENANCE T O REASSEMBLE UNIVERSAL JOINT 1. Smear grease into be arings and check for dirt. CAUTION! Make sure all needle bearin gs are seated properly . 2. Insert cup and cross . Drive in with spacer . 3. Insert snap ring 4. Insert second cup and ho ld cross into cup. D ...
-
Alamo Eagle 14 - page 162
MAINTENANCE Eagle 20 03/09 Maintenance Section 5-12 © 2009 Alamo Group Inc. MAINTENANCE 5. Drive cup down with spacer and in sert snap ring 6. T o loosen cross, st rike yoke arm and check cross for free rotation 7. Position second yoke on cross. Repeat S teps 2 to 6. Grease Kit after assembly is completed. ...
-
Alamo Eagle 14 - page 163
MAINTENANCE Eagle 20 03/09 Maintenance Section 5-13 © 2009 Alamo Group Inc. MAINTENANCE BLADE SER VICING Inspect blades before each use to determine that they ar e properly inst alled and in good con dition. Replace any blade that is bent, excessively nicked, worn, or has any other damage. Small nicks can be grou nd out when sharpening. Use only o ...
-
Alamo Eagle 14 - page 164
MAINTENANCE Eagle 20 03/09 Maintenance Section 5-14 © 2009 Alamo Group Inc. MAINTENANCE BLADE SHARPENING Always sharpen both blades at same time to maint a in balance. Follow or iginal sh arpening p attern as shown in FIGURE 1 1 . Always sharpen blades by grinding . DO NO T heat and po un d out edge. Do not sh ar pen blade to a razor edge, but lea ...
-
Alamo Eagle 14 - page 165
MAINTENANCE Eagle 20 03/09 Maintenance Section 5-15 © 2009 Alamo Group Inc. MAINTENANCE BLADE CARRIER REMOV AL Remove cotter pin and loosen slotted nut on gear box shaft. L oosen but do not remove the nut until the blad e carrier is loosened. Use a suitable tw o-jaw gear puller to pull carrier of f t apere d gear box shaf t. If gear p uller is not ...
-
Alamo Eagle 14 - page 166
MAINTENANCE Eagle 20 03/09 Maintenance Section 5-16 © 2009 Alamo Group Inc. MAINTENANCE BLADE CARRIER INST ALLA TION Clean the tape r and keyway on both the blade carrier and ou tput shaft. Po sition carrier on the ge ar box output shaft and install fla t washer and 1" hex nut. T ighten the nut holding the blade carrier to minimum 4 50 ft. po ...
-
Alamo Eagle 14 - page 167
MAINTENANCE Eagle 20 03/09 Maintenance Section 5-17 © 2009 Alamo Group Inc. MAINTENANCE TIRES AND WHEELS Before working on any tires a nd wheels make certa in the Cutter is jacked up high eno ugh and securely supported. When inst alling laminated or airplane tires, be sur e the flat side of the lug nut is again st the Wh ee l. When installing Sect ...
-
Alamo Eagle 14 - page 168
MAINTENANCE Eagle 20 03/09 Maintenance Section 5-18 © 2009 Alamo Group Inc. MAINTENANCE HYDRAULIC HOSES Replace pinched and broken Hyd raulic Hoses at once. T igh ten any Hydraulic Fitting with fluid leaking from it. If fluid still leaks, loosen the fitting, apply a pipe thr ead compound to the threads and tighten. Care must be exercised when tigh ...
-
Alamo Eagle 14 - page 169
MAINTENANCE Eagle 20 03/09 Maintenance Section 5-19 © 2009 Alamo Group Inc. MAINTENANCE PROPER TORQUE FOR F ASTENERS The chart lists the correct tightening torque for fastener s. When bolt s are to be tightened or replaced, r efer to this chart to determine the grade of bolts and the prop er torque except when specific torque values are assigned i ...
-
Alamo Eagle 14 - page 170
MAINTENANCE Eagle 20 03/09 Maintenance Section 5-20 © 2009 Alamo Group Inc. MAINTENANCE Gearbox T o ols For Disa ssembly and Assembly 1. Caulking Gun w/Silicon 2. Impact Wr ench6. 3. Chisel 3/16" wide Blade 4. Ball Pin Hammer 5. T orque Wrenc h 6. 3/16 " Punch 7. 10 mm & 14 mm Socket BE CERT AIN TO CLAMP OR SECUREL Y SUPPORT THE GEAR ...
-
Alamo Eagle 14 - page 171
MAINTENANCE Eagle 20 03/09 Maintenance Section 5-21 © 2009 Alamo Group Inc. MAINTENANCE Disassembly of Divider Gearbox (T rained dealer per sonnel only) STEP 1 Remove all eight of the M10 Bolts fr om both Cap Hubs, using a 14 mm socket. FIGURE Mnt-R- 0048 . Remove the Hub Assemblies and gaskets from the Ma in Housing. FIGURE Mnt-R-0048. STEP 2 Rem ...
-
Alamo Eagle 14 - page 172
MAINTENANCE Eagle 20 03/09 Maintenance Section 5-22 © 2009 Alamo Group Inc. MAINTENANCE STEP 3 Laying the Hub Assembly on it s side, tap the Ge ar end of the Output Shaf t into the Gear and Bearing. Once the Shaft has cleare d the Bearing, it c an be fully rem o ved from the Hub Assembly . The remaining Bearings and Bearing Cups can be removed by ...
-
Alamo Eagle 14 - page 173
MAINTENANCE Eagle 20 03/09 Maintenance Section 5-23 © 2009 Alamo Group Inc. MAINTENANCE STEP 5 The Input Gear and Bearing can be removed from the In put Shaft by tapp ing the end of the Input Shaf t on a solid surface. FIGURE Mnt-R-0052. The unit is now completely disassemb led with exc eption of O il Seals an d Bearin g Races that can be remo ved ...
-
Alamo Eagle 14 - page 174
MAINTENANCE Eagle 20 03/09 Maintenance Section 5-24 © 2009 Alamo Group Inc. MAINTENANCE STEP 3 Apply some Locktite on the Adjusting Nut FIGU RE Mnt-R-0059 . Install the Adjusting Nut onto the Shaft FIGURE Mnt-R-0060 . T ighten the Nut until it is difficult to turn the Shaf t FIGURE Mnt-R-0061 . While holding Hub, tap each end of the Shaf t and che ...
-
Alamo Eagle 14 - page 175
MAINTENANCE Eagle 20 03/09 Maintenance Section 5-25 © 2009 Alamo Group Inc. MAINTENANCE STEP 4 Apply a small amount of Silicon sealer to the bore of the Hub Cap and to the outside diameter of the Seal . FIGURE Mnt-R-0063. Drive the Seal into the base of the Hub Cap. FIGURE Mnt-R-0 064-0067. Care should be taken to keep the Seal in line with the ba ...
-
Alamo Eagle 14 - page 176
MAINTENANCE Eagle 20 03/09 Maintenance Section 5-26 © 2009 Alamo Group Inc. MAINTENANCE STEP 5 Install the Bearing Race into the Main Gear Box Housing. STEP 6 ...
-
Alamo Eagle 14 - page 177
MAINTENANCE Eagle 20 03/09 Maintenance Section 5-27 © 2009 Alamo Group Inc. MAINTENANCE Install Bearing on the Shaft. On the op posite end of th e Shaft, inst all one .012" and o ne .020" Gear Adjusting Shims. Inst all the Gear S pacer and the Gear . Install one .020" thick Gear Ad justing Shim and inst all the Bearing. FIGURE Mnt-R ...
-
Alamo Eagle 14 - page 178
MAINTENANCE Eagle 20 03/09 Maintenance Section 5-28 © 2009 Alamo Group Inc. MAINTENANCE Install a tot al thickness of .020" of Shims onto Hub Ca p. Mount the Hub Caps on th e Housing and inst all four Bolts, pla cing them in every other bolt hole, and tigh te n. Check the rotation of the Gear mesh. The Gea r set should turn smoothly with litt ...
-
Alamo Eagle 14 - page 179
MAINTENANCE Eagle 20 03/09 Maintenance Section 5-29 © 2009 Alamo Group Inc. MAINTENANCE Install the second S pindle Hub assembly on the Main Housing . Check the amount of backlash present between its Gea r and the G ear on th e Input Sh aft. Th e amount of backlash betw een these two Gears needs to be set to the same amount that wa s set on the fi ...
-
Alamo Eagle 14 - page 180
MAINTENANCE Eagle 20 03/09 Maintenance Section 5-30 © 2009 Alamo Group Inc. MAINTENANCE ITEM QTY DESCRIPTION 1. 1 Casing 2. 1 Bearing, Lower Outp ut 3. 1 Seal, Lower Output 4. 1 Nut, Slotted 5. 1 Cotter Pin 6. 1 Shaf t, Output 7. 1 Gear , Output 8. 1 Nut, Slotted 9. 1 Cotter Pin 10. 3 Bearing, Upper Output,Inner & Outer Input 1 1. 1 S pacer , ...
-
Alamo Eagle 14 - page 181
MAINTENANCE Eagle 20 03/09 Maintenance Section 5-31 © 2009 Alamo Group Inc. MAINTENANCE RIGHT ANGLE GEARBOX (OUTBOAR D) ASSEMBL Y & DISASSEMBL Y PROCEDURES INPUT SHAFT REMOV AL Ste p 1. Place Gearbox on approp riate work su rface. Ste p 2. Remove V ent Plug (item #16) or Complete T op Cover (item #18) Ste p 3. Tu rn Gearbox upside doan allowin ...
-
Alamo Eagle 14 - page 182
MAINTENANCE Eagle 20 03/09 Maintenance Section 5-32 © 2009 Alamo Group Inc. MAINTENANCE OUTPUT SHAFT INST ALLA TION Ste p 1 . Install Upper Ou tp ut Shaf t Bearing Cup (ite m # 1 2) in to Main Ho using from the to p, Inst all Output Shaf t Lower Bearing Cup (item # 2) into Main Housin g (item # 1) from the bottom, Make sure both Bearing Cup ar e s ...
-
Alamo Eagle 14 - page 183
...
-
Alamo Eagle 14 - page 184
ALAMO-INDUSTRIAL LIMITED W ARRANTY 1. LIMITED W ARRAN TIES 1.01. Alamo Industrial warrants for one year from the purchase d ate to the original non-commercial, governmental, or municipal purchaser (“Purchaser ”) and warrants for six months to the original commercial or industrial purchaser 1.02. Manufacturer will replace for the Purcha ser any ...
-
Alamo Eagle 14 - page 185
T o keep your implement running ef ficiently and safely , read your manual thoroughly and follow these directions and the Safety Messages in this Ma nual. The T able of Cont ents clearly identifies each section where you can easily find the information you need. The OCCUP A TIONAL SAFETY AND HEAL TH ACT (1928.51 Subp art C) makes these minimum safe ...
-
Alamo Eagle 14 - page 186
EAGLE 20/14 - SOM 3/09 Printed in USA P/N 00779092C ...
Avez-vous une question à propos de Alamo Eagle 14?
Utiliser le formulaire ci-dessous
Si vous n’avez pas résolu votre problème avec Alamo Eagle 14, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Alamo Eagle 14 il est probable qu’il a envie de partager la façon de le résoudre.