Français dropdown-ico

Manuel d’utilisation Makita 2703

28 pages 0.58 mb
Télécharger

Aller à la page of 28

Summary
  • Makita 2703 - page 1

    With Electric Brake 210 mm (8-1/4”) MODEL 2702X1 MODEL 2702 255 mm (10”) MODEL 2703X1 MODEL 2703 T able Saw www .makita.com INSTRUCTION MANUAL DOUBLE INSULA TION W ARNING: For your personal safety , READ and UNDERST AND before using. SA VE THESE INSTRUCTIONS FOR FUTURE REFERENCE. ...

  • Makita 2703 - page 2

    2 MODEL Arbor hole Blade diameter Cutting capacities 90 ° 45 ° T able size (W x L) No load speed (RPM) Dimensions (L x W x H) Maximum dado capacity Net weight 18kg (40 lbs) 4,600/min 560mm x 686mm x 458mm (22" x 27" x 18") 686mm x 560mm (27" x 22") 2702X1 2702 2703X1 2703 5/8" 13 mm (1/2") 210mm (8-1/4") 68 ...

  • Makita 2703 - page 3

    3 9. USE RIGHT TOOL. Don’t force tool or attachment to do a job for which it was not designed; for example, don’t use circular saw for cutting tree limbs or logs. 10. WEAR PROPER APP AREL. Wear no loose clothing, gloves, neckties, rings, bracelets, or other jewelry which may get caught in moving parts. Nonslip footwear is recommended.Wear prote ...

  • Makita 2703 - page 4

    4 16. REDUCE THE RISK OF UNINTENTIONAL ST ARTING. Make sure switch is in off position before plugging in. 17. USE RECOMMENDED ACCES- SORIES. Consult the owner ’s manual for recom- mended accessories. The use of improper accessories may cause risk of injury to persons. 18. NEVER ST AND ON TOOL. Serious injury could occur if the tool is tipped or i ...

  • Makita 2703 - page 5

    5 1. Wear eye protection. 2. Don ’ t use the tool in presence of flam- mable liquids or gases. 3. NEVER use the tool with an abrasive cut-off wheel installed. 4. Check the blade carefully for cracks or damage before operation. Replace cracked or damaged blade immediately . 5. Clean the spindle, flanges (especially the installing surface) and hex ...

  • Makita 2703 - page 6

    6 18. Do not perform any operation freehand. Freehand means using your hands to sup- port or guide the workpiece, in lieu of a rip fence or miter gauge. 19. NEVER reach around or over saw blade. NEVER reach for a workpiece until the saw blade has completely stopped. 20. Avoid abrupt, fast feeding. Feed as slowly as possible when cutting hard work- ...

  • Makita 2703 - page 7

    The tool is shipped from the factory with the saw blade and blade guard not in the installed condition. Assemble as follows: CAUTION: • Always unplug the tool before assembly . Installing saw blade Remove the table insert on the table. Hold the outer flange with the offset wrench and loosen the hex nut counterclockwise with the wrench. Then remov ...

  • Makita 2703 - page 8

    8 Installing blade guar d CAUTION: • Before installing the blade guard, adjust the depth of cut to its maximum elevation. Insert the spreader between the blade guard mounting portion (stay) and the pressure plate. T ighten the hex bolts (A) with the offset wrench. The spreader installing location is factory-adjusted so that the blade and spreader ...

  • Makita 2703 - page 9

    9 P ositioning table saw Locate the table saw in a well lit and level area where you can maintain good footing and balance. It should be installed in an area that leaves enough room to easi- ly handle the size of your workpieces. The table saw should be secured with four screws or bolts to the work bench or table saw stand using the holes provided ...

  • Makita 2703 - page 10

    10 Adjusting depth of cut The depth of cut may be adjusted by turning the han- dle. T urn the handle clockwise to raise the blade or counterclockwise to lower it. NOTE: • Use a shallow depth setting when cutting thin materi- als in order to obtain a cleaner cut. Adjusting bevel angle Loosen the lock lever counterclockwise and turn the handwheel u ...

  • Makita 2703 - page 11

    After adjusting the positive stops, set the blade at 90 ° to the table surface. Then adjust the arrow pointer so that its right edge is aligned to the 0 ° graduation. Installing and adjusting rip fence Raise the grip of the rip fence. Install the rip fence on the table so that the fence holder engages with the guide rail. The rip fence can be sec ...

  • Makita 2703 - page 12

    12 CAUTION: • Always grasp the striped portion of the wrench when tightening the hex bolts. If you tighten the hex bolts while grasping the wrench further than the striped por- tion, the hex bolts may be damaged and/or an injury to your hand may result. 6. With the grip of the rip fence lowered, turn the adjust- ing nut clockwise to secure the re ...

  • Makita 2703 - page 13

    When operating the switch lever , it is convenient to view it through the window area in the table. CAUTION: • When not using the tool, remove the key and store it in a secure place. This prevents unauthorized opera- tion. • Before plugging in the tool, always check to see that the switch lever actuates properly and returns to the “ OFF ” p ...

  • Makita 2703 - page 14

    14 Push stick A push stick can be easily made from a piece of ply- wood 19 mm (3/4 ” ) to 25 mm (1 ” ) thick. Cut out the hatched area on the stick and smooth edges with a file. (H) dimension should be less than 12.7 mm (1/2 ” ) so as to be thinner than the workpiece. Push bloc k Use a 19 mm (3/4 ” ) piece of plywood. Handle should be in ce ...

  • Makita 2703 - page 15

    W ood facing (rip fence) A wood facing should be used for operations when the blade comes close to the rip fence. Wood facing for the rip fence should be the same size as the rip fence. Make sure the bottom of facing is flush with the table surface. Crosscutting CAUTION: • When making a crosscut, remove the rip fence from the table. • When cutt ...

  • Makita 2703 - page 16

    16 A uxiliary wood facing (miter gauge) T o prevent a long board from wobbling, fit the miter gauge with an auxiliary fence board. Fasten with bolts/nuts after drilling holes, but fasteners must not protrude from the face board. Ripping CAUTION: • When ripping, remove the miter gauge from the table. • When cutting long or large workpieces, alwa ...

  • Makita 2703 - page 17

    3. T urn the tool on and gently feed the workpiece into the blade along with the rip fence. (1) When the width of rip is 150 mm (6 ” ) and wider , carefully use your right hand to feed the work- piece. Use your left hand to hold the workpiece in position against the rip fence. (2) When the width of rip is 65 mm - 150 mm (2-1/2 ” - 6 ” ) wide, ...

  • Makita 2703 - page 18

    CAUTION: • Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. Cleaning Clean out sawdust and chips from time to time. Carefully clean the blade guard and moving parts inside the table saw . Lubrication T o keep the table saw in tip-top running condition, and to assure maximum service ...

  • Makita 2703 - page 19

    19 CAUTION: • These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated pur- pose. Dado head set (Part No. 191543-4) A dado is cutting a rabbet or a wide groove i ...

  • Makita 2703 - page 20

    T able insert (Part No. 317061-6) When cutting grooves 5/16 ” , 3/8 ” ,7/16 ” or 1/2 ” use this table insert instead of the standard table insert. T o install the dado head set, proceed as follows: 1. T urn the tool off and unplug it before installing. 2. Remove the blade guard with the spreader . 3. Install the dado head set with the teeth ...

  • Makita 2703 - page 21

    21 NOTE: • When widths slightly greater than the above are required, fit the paper washers in between the inside and outside cutters to adjust the width. 5. Arrange the cutters so that the tips of the inside cut- ters are positioned at the gullets of the outside cutter . When more than one inside cutter is used, space the tips of the inside cutte ...

  • Makita 2703 - page 22

    Featherboards are used to keep the workpiece in con- tact with the rip fence and table as shown, and to stop kickbacks. T o install featherboards, proceed as follows: 1. T urn the tool off and unplug it. 2. Add 8 ” high flat facing board to the rip fence, the full length of the rip fence. 3. Mount featherboards to the rip fence and table as shown ...

  • Makita 2703 - page 23

    23 How to perf orm rabbeting 1. Remove blade guard. 2. Attach auxiliary fence to rip fence for cuts that run the length of the stock. Facing should be as high as the workpiece is wide. Adjust fence and blade to desired dimensions. 3. First cut: Hold board flat on table as in ordinary rip- ping. 4. Second cut: Set workpiece on its edge. (Use feather ...

  • Makita 2703 - page 24

    24 CAUTION: • These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose. If you need any assistance for more details regarding these accessories, ask your ...

  • Makita 2703 - page 25

    21 First-Class Postage Required Post Office will not deliver without proper postage. Makita U .S.A., Inc. 14930 Nor tham Street La Mirada, CA 90638-5753 Fold Cut ...

  • Makita 2703 - page 26

    22 1. This product was purc hased from: Home Center Hardware/Lumber Store T ool Distributor Industrial Supply Construction Supply Other ( ) 3. Ho w did you learn about this product: Magazine F rom Dealer Newspaper Store Display Catalog Radio Exhibition F rom Friend Previous Usage Other ( ) 2. Use of the pr oduct is intended for: Construction T rade ...

  • Makita 2703 - page 27

    2 7 F A CT OR Y SER VICE CENTERS 1-800-4-MAKIT A RET AIN THIS POR TION FOR Y OUR RECORDS ALABAMA 2365 Pelham P arkway Pelham, AL 35124 (205) 620-1791 ARIZONA 3707 E. Broadw ay Rd., Ste. 6 Phoenix, AZ 85040 (602) 437-2850 ARKANSAS Shackleford Shopping Center 240 South Shackleford Rd., Ste. C Little Rock, AR 72211 (501) 224-5733 CALIFORNIA 41850 Chri ...

  • Makita 2703 - page 28

    W ARNING Some dust created by po wer sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of Calif or nia to cause cancer , bir th defects or other reproductiv e har m. Some e xamples of these chemicals are: • lead from lead-based paints, • cr ystalline silica from bricks and cement and ot ...

Fabricant Makita Catégorie Saw

Les documents que nous recevons du fabricant de l'appareilMakita 2703 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Makita
- manuels d’utilisations 2703
- fiches produit Makita
- dépliants
- ou étiquettes-énergie Makita 2703
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Makita 2703.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Makita 2703, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Makita 2703. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Makita 2703.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Makita 2703, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Makita 2703 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Makita 2703.

Le manuel d’utilisation complet Makita, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Makita 2703 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Makita 2703, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lMakita 2703 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Makita 2703 - qui devraient nous aider dans les premières étapes lors de l'utilisation Makita 2703
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Makita 2703
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Makita 2703 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Makita 2703?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Makita 2703, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Makita 2703 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)