Français dropdown-ico

Manuel d’utilisation Henny Penny PFG-690

106 pages 5.1 mb
Télécharger

Aller à la page of 106

Summary
  • Henny Penny PFG-690 - page 1

    Henny Penny Pressure Fryer Model PFG-690 TECHNICAL MANUAL ...

  • Henny Penny PFG-690 - page 2

    ...

  • Henny Penny PFG-690 - page 3

    Model 690 810 FM06-006 Revised 8-12-10 This manual should be retained in a convenient location for future reference. A wiring diagram for this appliance is located on the rear shroud cover of the control panel. Post in a prominent location, instructions to be followed if user smells gas. This information should be obtained by consulting the local g ...

  • Henny Penny PFG-690 - page 4

    Model 690 HENNY PENNY 8 HEAD GAS PRESSURE FR YER SPECIFICA TIONS Height 61” (155 cm) W idth 24” (61 cm) Depth 41¾” ( 106 cm) Floor Space Approximately 7 sq. ft. (0.65 sq. m.) Pot Capacity 8 Head of chicken (32 lbs.) (14.4 kg.) 130 lbs. shortening (59 kg.) Electrical 120 V AC, 1 Phase, 50/60 Hz, 10 Amp, 3 W ire Service 240 V AC, 1 Phase, 50/6 ...

  • Henny Penny PFG-690 - page 5

    Model 690 T ABLE OF CONTENTS Section Page Section 1. TROUBLESHOOTING .............................................................................................. 1-1 1-1. Introduction .................................................................................................... 1-1 1-2. Safety ............................................... ...

  • Henny Penny PFG-690 - page 6

    Model 690 T ABLE OF CONTENTS (Continued) Section Page Section 2 MAINTENANCE (Continued) 230 V olt Ladder Diagram (AP0803002 & BELOW) ..................................... 2-37 230 V olt Ladder Diagram (AP0803003 & ABOVE) ...................................... 2-38 100-120 V olt F AST W iring Diagram (AP0803002 & BELOW) ................. ...

  • Henny Penny PFG-690 - page 7

    Model 690 1-1. INTRODUCTION This section provides troubleshooting information in the form of an easy-to-read table. If a problem occurs during the f rst operation of a new fryer , recheck the installation per the Installation section of the Operator ’ s Manual. Before troubleshooting, always recheck the operation pro- cedures per section 3 of the ...

  • Henny Penny PFG-690 - page 8

    Model 690 1-3. TROUBLESHOOTING T o isolate a malfunction, proceed as follows: 1. Clearly def ne the problem (or symptom) and when it occurs. 2. Locate the problem in the T roubleshooting table. 3. Review all possible causes. Then, one at a time, work through the list of corrections until the problem is solved. 4. Refer to the maintenance procedures ...

  • Henny Penny PFG-690 - page 9

    Model 690 Problem Cause Correction COOKING SECTION Product Color Not Correct: A. T oo Dark • T emperature too high • Check temperature setting in the program mode; see Programming section of Operator ’ s Manual • Faulty temperature probe • Remove and replace tempera- ture probe • Shortening too old • Change shortening • Shortening t ...

  • Henny Penny PFG-690 - page 10

    Model 690 Problem Cause Correction COOKING SECTION (Continued) D. Spotted • Improper separation of the • Load product into basket Product product properly • Breading not uniform on • Sift breading regularly the product • Separate product during breading • Burned breading particles • Filter the shortening more on product frequently • ...

  • Henny Penny PFG-690 - page 11

    Model 690 Problem Cause Correction COOKING SECTION (Continued) D. Rancid T aste • Shortening too old • Replace shortening and follow recommended care and use of shortening • Infrequent f ltering • Replace shortening and follow recommended care and use of shortening • Non-compatible products • Replace shortening cooked within the same ? ...

  • Henny Penny PFG-690 - page 12

    Model 690 Problem Cause Corr ection POWER SECTION W ith switch in • Open circuit • Check to see that unit is POWER position, plugged in the fryer is com- • Check the breaker or fuse pletely inoperative at supply box (NO POWER) • Check voltage at wall receptacle • Check MAIN POWER switch; replace if defective • Check cord and plug PRESSU ...

  • Henny Penny PFG-690 - page 13

    Model 690 Problem Cause Correction PRESSURE SECTION (Continued) Pressure does not • Not enough product in fryer • Place proper quantity of build or product not fresh fresh product within frypot to generate steam • Metal shipping spacer not • Remove shipping spacer; removed from deadweight see Unpacking section of Operator ’ s Manual • L ...

  • Henny Penny PFG-690 - page 14

    Model 690 • Gas valve knob turned to the OFF • Make sure the gas valve knob is position turned to the ON position • Blown fuse or tripped • Reset breaker or replace fuse circuit breaker at supply box or control panel • Blown fuse in PC board • Replace glass fuse in board • Faulty Power/Pump switch • Check Power/Pump switch per maint ...

  • Henny Penny PFG-690 - page 15

    Model 690 Problem Cause Correction HEA TING OF SHOR TENING SECTION (Continued) Heating of • Supply line too small - low • Increase supply line size; shortening too gas volume refer to installation slow instructions • Improper ventilation • Refer to installation system instructions • Observe burners • Check gas pressure • Clean dilutio ...

  • Henny Penny PFG-690 - page 16

    Model 690 Pr oblem Cause Correction SHOR TENING FOAMING/DRAINING SECTION Foaming or boil- • W ater in shortening • At end of a cook cycle, ing over of drain shortening and clean shortening frypot; add fresh shortening • Condensation line stopped up • Remove and clean conden- sation line • Improper or bad • Use recommended shortening sho ...

  • Henny Penny PFG-690 - page 17

    Model 690 806 1-1 1 1-4. ERROR CODES In the event of a control system failure, the digital display shows an error message. These messages are coded: “E-4”, “E-5”, “E-6”, “E-32”, “E-41” and “E-71”. A constant tone is heard when an error code is displayed, and to silence this tone, press any of the product buttons. DISPLA Y CA ...

  • Henny Penny PFG-690 - page 18

    Model 690 1-4. ERROR CODES (Continued) CE Only - Along with error codes fr om preceding page, CE units have the following self-diagnostic error codes: DISPLA Y CAUSE P ANEL BOARD CORRECTION “E-10” High limit Allow unit to cool (15-20 minutes), reset the high limit by manually pushing up on red reset button; if high limit does not reset, high li ...

  • Henny Penny PFG-690 - page 19

    Model 690 2-1. INTRODUCTION This section provides checkout and replacement procedures for various parts of the fryer . Before replacing any parts, refer to the T roubleshooting section to aid you in f nding the cause of the malfunction. 2-2. MAINTENANCE HINTS 1. A multimeter will help you check the electric components. 2. When the manual refers to ...

  • Henny Penny PFG-690 - page 20

    Model 690 2-4. HIGH TEMPERA TURE LIMIT CONTROL This high temperature control is a safety , manual reset control, which senses the temperature of the shortening. If the shorten- ing temperature exceeds 425°F (218°C), this switch opens and shuts off the heat to the frypot. When the temperature of the shortening drops to a safe operation limit (15-2 ...

  • Henny Penny PFG-690 - page 21

    Model 690 2-4. HIGH TEMPERA TURE LIMIT CONTROL (Continued) Replacement T o avoid electrical shock or pr operty damage, move the power switch to OFF and disconnect main circuit breaker , or unplug cord at wall receptacle. 1. If the tube is broken or cracked, the control will open, shutting off electrical power . The control cannot be reset. 2. Drain ...

  • Henny Penny PFG-690 - page 22

    Model 690 2-4. HIGH TEMPERA TURE 1 1. Pull all excess capillary line from the frypot and tighten nut LIMIT CONTROL into frypot wall. (Continued) Be sur e capillary bulb of high limit is positioned so it does not interfer e with the carrier or get damages when clean- ing the frypot. 12. W ith excess capillary line pulled out, tighten smaller nut. 13 ...

  • Henny Penny PFG-690 - page 23

    Model 690 2-5. POWER/PUMP SWITCH (Continued) Replacement 1. W ith control panel removed, and wires of f the switch, push in on tabs on the switch to remove from the panel. 2. Replace with new switch, and reconnect wires to switch following the wiring diagram. 3. Replace the control panel. 2-6. TEMPERA TURE PROBE T emperature Probe relays the actual ...

  • Henny Penny PFG-690 - page 24

    Model 690 2-6. TEMPERA TURE PROBE 7. T ighten hand tight and then a half turn with wrench. REPLACEMENT (Continued) Excess force will damage temperature probe. 8. Connect new temperature probe to PC board and replace Control Panel. 9. Replace shortening. 10. T urn power ON and check out fryer . 2-7. COMPLETE CONTROL Should the Control Panel become i ...

  • Henny Penny PFG-690 - page 25

    Model 690 2-8. PRESSURE REGULA TION The Henny Penny Fryer uses pressure as one of the compo- nents of the cooking process. Once the lid is sealed to the frypot and the solenoid valve closes, a deadweight valve maintains the correct pressure in the frypot. The lid has minimal and limited maintenance and repair proce- dures, which are addressed in th ...

  • Henny Penny PFG-690 - page 26

    Model 690 2-10. REVERSING THE LID The gray rubber gasket surrounding the inside of the lid is GASKET designed to be reversed. Because of heat expansion and the pressure used for the cook ing process, the gasket is constantly under extreme stress. Reversing the lid gasket will help to ensure that the fryer will not lose pressure through leakage. 1. ...

  • Henny Penny PFG-690 - page 27

    Model 690 The Lid Counterweight in the back of the fryer balances the weight of the lid system to allow easier opening and closing of the lid. The weight has two cables attached to it, and weighs about 150 lbs. (67.5 Kg). 1. Using a 3/8” socket, remove the nuts securing the rear shroud of the fryer and remove the shroud. 2. Using Phillip’ s-hea ...

  • Henny Penny PFG-690 - page 28

    Model 690 2-12. PRESSURE P AD The pressure pads are plastic strips that the lid cam presses against to seal the lid. 1. Raise the lid. 2. Remove the four screws securing the lid cover and remove cover . 3. Push the lid cam back, off the pressure pads. 4. Using an Allen wrench, remove the large bolt securing pad. 5. Using a Phillips head screw drive ...

  • Henny Penny PFG-690 - page 29

    Model 690 2-13. LID ADJUSTMENT If steam leaks out from around the lid gasket, the pressure pads could be worn or broken. If the pressure pad is worn, but not broken, it can be reversed 180 degrees, and the other end of the pad used. See Section 2-12. If steam leaks, check for: • Pressure pad wear • Cracked or worn gasket • Gasket installed im ...

  • Henny Penny PFG-690 - page 30

    Model 690 2-15. SOLENOID V AL VE This is an electromechanical device that causes pressure to be held in the frypot. The solenoid valve closes at the beginning of the cook cycle and opens automatically at the end of the cook cycle. If this valve should become dirty , or the T ef on seat nicked, pressure will not build up. The gas fryer uses a 120 vo ...

  • Henny Penny PFG-690 - page 31

    Model 690 2-15. SOLENOID V AL VE 5. If the core-disc assembly is sticking due to buildup of (Continued) shortening, breading, and food particles, proceed with the following steps: a. Unscrew the solenoid bonnet assembly from solenoid valve body . b. Remove the solenoid bonnet assembly and bonnet gasket. c. Remove the core-disc assembly , core sprin ...

  • Henny Penny PFG-690 - page 32

    Model 690 2-15. SOLENOID V AL VE 13. W et O-ring around seat with water and insert O-ring (Continued) assembly (f at side f rst) in valve through “IN” side of body . Use an eraser end of pencil and press in the T ef on seal until it snaps into place. BE CAREFUL NOT TO MAR OR NICK THE SEA T . The smallest nick can cause a pressure leak. Replace ...

  • Henny Penny PFG-690 - page 33

    Model 690 2-16. DEADWEIGHT V AL VE (Continued) DO NOT PULL THE RING ON SAFETY RELIEF V AL VE. HOT STEAM WILL BE RELEASED AND SEVERE BURNS WILL RESUL T . 1. A T THE END OF EACH DA Y’S USAGE OF THE FR YER, THE DEADWEIGHT V AL VE MUST BE ORIFICE CAP WEIGHT CLEANED. The fryer must be OFF and the pressure released. Open the lid and then remove the dea ...

  • Henny Penny PFG-690 - page 34

    Model 690 2-17. REMOV AL & CLEANING 2. Use a wrench to loosen the valve from the pipe tee; turn OF SAFETY RELIEF V AL VE counterclockwise to remove. (Continued) 3. Clean the inside of the pipe tee with hot water . T urn the safety relief valve towards the rear of fryer when reinstalling safety relief valve. 4. Immerse the safety relief valve in ...

  • Henny Penny PFG-690 - page 35

    Model 690 2-19. GAS CONTROL V AL VE The gas control valve sends regulated gas to burners when the controller calls for heat. The control valve can be turned on or off. In ON position, and power switch ON, a spark ignitor lights a standing pilot, and when the control calls for heat, the valve is opened and the burners are ignited. Safety Precautions ...

  • Henny Penny PFG-690 - page 36

    Model 690 2-19. GAS CONTROL V AL VE (Continued) 4. Remove left side panel. 5. Remove control panel. 6. Unscrew nut from inlet line from the control valve. 7. Remove the bracket from behind the control valve. 8. Remove pilot light tube from control valve. 9. Loosen f ttings from tee and pull control valve assembly from the unit. 10. Remove the f tti ...

  • Henny Penny PFG-690 - page 37

    Model 690 2-20. BLOWER ASSEMBL Y The blower motor circulates air into the burner area to create the correct heat for the fryer . If the blower fails, a sensor will shut the power control valve down. 1. Make sure unit is off, and close and lock the lid. Lid should be in locked down position. Failure to do so could result in personal injury . 2. Remo ...

  • Henny Penny PFG-690 - page 38

    Model 690 2-21. TRANSFORMER The transformer reduces the voltage down to accommodate those components with low voltage. 1. Remove electrical power supplied to the unit. T o avoid electrical shock or pr operty damage, move the power switch to OFF and disconnect main circuit breaker , or unplug cord at wall receptacle. 2. Remove the control panel. 3. ...

  • Henny Penny PFG-690 - page 39

    Model 690 2-22. AIRFLOW SWITCH The air f ow switch senses the f ow of air coming from the blower . If the airf ow is reduced below a set amount, the switch will cut power to the control valve, which shuts the burners down. Replacement 1. Remove electrical power supplied to the unit. T o avoid electrical shock or pr operty damage, move the power swi ...

  • Henny Penny PFG-690 - page 40

    Model 690 2-23. DRAIN MICROSWITCH Upon pulling out on the drain handle, the microswitch should be activated and the unit will not heat, but when the handle is pushed back, the unit should operate properly . The bracket on the microswitch is slotted so it can be adjusted backward or `forward. 1. Remove electrical power supplied to the unit. T o avoi ...

  • Henny Penny PFG-690 - page 41

    Model 690 2-24. DRAIN V AL VE The drain valve opens when drain valve handle is pulled out AND EXTENSION and drains the shortening out of the pot. 1. Using a 3/8” socket, remove the nuts securing the drain switch bracket, and pull the bracket from the studs. 2. Remove the nut securing the drain handle and pull the handle from the drain valve. 3. U ...

  • Henny Penny PFG-690 - page 42

    Model 690 2-25. AIR V AL VE The air valve allows circulation of the shortening in the frypot to keep the shortening at a uniform temperature. 1. Remove electrical power supplied to the unit. T o avoid electrical shock or pr operty damage, move the power switch to OFF and disconnect main circuit breaker , or unplug cord at wall r eceptacle. 2. Remov ...

  • Henny Penny PFG-690 - page 43

    Model 690 2-26. CLEANING THE Clean the dilution box annually to ensure the unit operates DILUTION BOX ef f ciently and with few failures. 1. Make sure unit is off, and close and lock the lid. Lid should be in locked down position. Failure to do so could result in personal injury . 2. Remove the back shroud of the fryer . 3. Clean dilution box with ...

  • Henny Penny PFG-690 - page 44

    Model 690 2-28. IGNITION MODULES Sends 24 volts to the ignitors and gas control valve. LED Indication 3 different modules are in the f eld. The White Rogers and Fenwall modules have a red LED, and the Robertshaw modules have a green LED. These LEDs help to identify a failure. For White Rogers & Fenwall modules, when the control calls for heat, ...

  • Henny Penny PFG-690 - page 45

    Model 690 2-29. IGNITOR ASSEMBL Y The 690 Model has electronic spark ignition that lights a standing pilot. Replacement 1. Remove electrical power supplied to the unit. T o avoid electrical shock or pr operty damage, move the power switch to OFF and disconnect main circuit breaker , or unplug cord at wall r eceptacle. TO A VOID INJUR Y , PROPER TY ...

  • Henny Penny PFG-690 - page 46

    Model 690 2-30. FLAME SENSOR The f ame sensor should glow a bright red when pilot is lit and ASSEMBL Y allows the gas control valve to open. If it does not sense a f ame, it will shut the gas control valve down. Replacement 1. Remove electrical power supplied to the unit. T o avoid electrical shock or pr operty damage, move the power switch to OFF ...

  • Henny Penny PFG-690 - page 47

    Model 690 1. Raise the lid and remove the retention ring from one end of the lid pin. 2. Slide the lid pin from unit. 3. Lift the lid from unit. The lid weighs 80 lbs (36 kg). T ake care when lifting lid to prevent personal injury . 4. Using a 3/8” socket, remove the nuts securing the rear shroud and remove shroud. 5. Using a Phillip’ s-head sc ...

  • Henny Penny PFG-690 - page 48

    Model 690 2-30 507 2-32. NYLA TRON STRIPS REPLACEMENT (CONTD) 9. Lift the front shroud up and out, over the arm of the lid. 10. Thread the new nylatron strip through the track in the front shroud. 1 1. Lining up the holes in the strips, f t the front shroud back over the lid arms. 12. Secure the strips to the weight assembly . 13. Replace back shro ...

  • Henny Penny PFG-690 - page 49

    Model 690 708 2-31 AP0803002 & below ...

  • Henny Penny PFG-690 - page 50

    Model 690 AP0803003 & above 2-32 708 ...

  • Henny Penny PFG-690 - page 51

    Model 690 708 2-33 AP0803002 & below ...

  • Henny Penny PFG-690 - page 52

    Model 690 AP0803003 & above 2-34 708 ...

  • Henny Penny PFG-690 - page 53

    Model 690 708 2-35 AP0803002 & below ...

  • Henny Penny PFG-690 - page 54

    Model 690 AP0803003 & above 2-36 806 ...

  • Henny Penny PFG-690 - page 55

    Model 690 708 2-37 AP0803002 & below ...

  • Henny Penny PFG-690 - page 56

    Model 690 AP0803003 & above 2-38 806 ...

  • Henny Penny PFG-690 - page 57

    Model 690 708 2-39 100-120 V olt F AST Wiring Diagram AP0803002 & below ...

  • Henny Penny PFG-690 - page 58

    Model 690 AP0803003 & above 2-40 708 ...

  • Henny Penny PFG-690 - page 59

    Model 690 708 2-41 230 V olt F AST Wiring Diagram AP0803002 & below ...

  • Henny Penny PFG-690 - page 60

    Model 690 AP0803003 & above 2-42 708 ...

  • Henny Penny PFG-690 - page 61

    Model 690 708 2-43 220-240 V olt F AST Wiring Diagram AP0803002 & below ...

  • Henny Penny PFG-690 - page 62

    Model 690 AP0803003 & above 2-44 708 ...

  • Henny Penny PFG-690 - page 63

    Model 690 207 2-45 LIMITED W ARRANTY FOR HENNY PENNY EQUIPMENT Subject to the following conditions, Henny Penny Corporation makes the following limited warranties to the original pur - chaser only for Henny Penny appliances and replacement parts: NEW EQUIPMENT : Any part of a new appliance, except baskets, lamps, and fuses, which proves to be defec ...

  • Henny Penny PFG-690 - page 64

    Model 690 ...

  • Henny Penny PFG-690 - page 65

    Model 690 106 3-1 SECTION 3. P AR TS INFORMA TION 3-1. INTRODUCTION This section lists the replaceable parts of the Henny Penny Model 690 Fryer . 3-2. GENUINE P ARTS Use only genuine Henny Penny parts in your fryer . Using a part of lesser quality or substitute design may result in damage to the unit or personal injury . 3-3. WHEN ORDERING P AR TS ...

  • Henny Penny PFG-690 - page 66

    Model 690 FIGURE 3-0. FRAME & COVER ASSEMBL Y 3-2 1002 ...

  • Henny Penny PFG-690 - page 67

    Model 690 Figur e & Item No. Part No. Description Qty . 3-0 FRAME & COVER ASSEMBL Y 1 39796 WELDMENT – CONTROL P ANEL FRONT ........................... 1 2 53669 GUARD – POWER SWITCH ................................................... 1   3 29898 SWITCH – POWER ................................................................. ...

  • Henny Penny PFG-690 - page 68

    Model 690 Figur e & Item No. Part No. Description Qty . 3-1 CONTROL P ANEL   1 14418 KIT -CONTROL ASSY/AIR SWITCH MONIT OR.- SMS-DOM .... 1  1 14245 KIT -CONVERSION TO SMS-DOM ............................................... 1  1 14427 KIT -CONTROL -240V -NON-SMS T O SMS-DOM ........................ 1  1 14749 KIT -CON ...

  • Henny Penny PFG-690 - page 69

    Model 690 Figure & Item No. Part No. Description Qty . 3-2 ELECTRICAL CONTROLS   1 60207 TRANSFORMER ASSY – 120V ................................................... 1   1 60536 TRANSFORMER ASSY – 24V/230V ........................................... 1 2 SC03-005 SCREW ........................................................ ...

  • Henny Penny PFG-690 - page 70

    Model 690 Figure & Item No. Part No. Description Qty . 3-3A FR YPOT COVERS & INSULA TION 1 52799 ASSY -INSUL/LFT . C/CHAMBER ................................................... 1 2 52041 INSULA TION-C/CHAMBER MOUNTIN ....................................... 4 3 52798 ASSY -INSUL/R T . C/CHAMBER ............................................... ...

  • Henny Penny PFG-690 - page 71

    Model 690 Figur e & Item No. Part No. Description Qty . 3-3B INSULA TION COVERS 1 W A02-001 W ASHER – INSULA TION 1-1/2” DIA. ................................ 17 2 51763 INSULA TION COVER – LEFT ............................................. 1 3 51892 INSULA TION – C/CHAMBER SIDE ................................... 2 4 51765 INSULA TION ...

  • Henny Penny PFG-690 - page 72

    Model 690 3-8 707 FIGURE 3-4. LID & COVER ASSEMBL Y ...

  • Henny Penny PFG-690 - page 73

    Model 690 Figur e & Item No. Part No. Description Qty . 3-4 LID & COVER ASSEMBL Y 1 35792 LID INSTRUCTION LABEL ................................................ 1 2 35675 FILLER-LID ........................................................................... 2 3 35243 COVER-MAIN LID ........................................................... ...

  • Henny Penny PFG-690 - page 74

    Model 690 3-10 810 FIGURE 3-5. DRAIN P AN & FIL TER ASSEMBL Y ...

  • Henny Penny PFG-690 - page 75

    Model 690 Figur e & Item No. Part No. Description Qty . 3-5 DRAIN P AN & FIL TER ASSEMBL Y 1 52194 CRUMB CA TCHER (OPTIONAL) (REQUIRES ITEM 10) ....... 1 2* 03204 CRUMB CA TCHER BASKET W/HANDLE (OPTIONAL) ........ 1 (FITS INSIDE FR YPOT) 2* 21010 . “COLD ZONE” CRUMB CA TCHER BASKET ASSEMBL Y .. 1 2* 24429 . HANDLE - CRUMB BASKET ....... ...

  • Henny Penny PFG-690 - page 76

    Model 690 3-12 810 FIGURE 3-6. FIL TER PUMP ASSEMBL Y (BELOW SN: AP0401001) ...

  • Henny Penny PFG-690 - page 77

    Model 690 Figure & Item No. Part No. Description Qty . 3-6 FIL TER PUMP ASSEMBL Y (BELOW SN: AP0401001) 1 18107 CONDUIT CONNECTOR 3/8 X 90 ................................................. 2 2 54484 BLOWER/PUMP – FLEXIBLE CONDUIT ..................................... 1   3 17476 PUMP SEAL KIT ......................................... ...

  • Henny Penny PFG-690 - page 78

    Model 690 FIGURE 3-7. FIL TER PUMP ASSEMBL Y (SN: AP0401001 & ABOVE) 3-14 905 ...

  • Henny Penny PFG-690 - page 79

    Model 690 Figure & Item No. Part No. Description Qty . 3-7 FIL TER PUMP ASSEMBL Y (SN: AP0401001 & ABOVE) 1 18107 CONDUIT CONNECTOR 3/8 X 90 ............................................. 2 2 54484 BLOWER/PUMP – FLEXIBLE CONDUIT ................................. 1   3 17476 PUMP SEAL KIT ........................................... ...

  • Henny Penny PFG-690 - page 80

    Model 690 3-16 806 FIGURE 3-8. GAS BURNER ASSEMBL Y ...

  • Henny Penny PFG-690 - page 81

    Model 690 Figur e & Item No. Part No. Description Qty . 3-8 GAS BURNER ASSEMBL Y 0* 56990-01 BURNER ASSY – NA TURAL ...................................................... 2 0* 56990-02 BURNER ASSY – LP .................................................................... 2 0* 56990-03 BURNER ASSY – NA TURAL CE ............................. ...

  • Henny Penny PFG-690 - page 82

    Model 690 3-18 1209 FIGURE 3-9. GAS PIPING & CONTROLS ...

  • Henny Penny PFG-690 - page 83

    Model 690 Figur e & Item No. Part No. Description Qty . 3-9 GAS PIPING & CONTROLS 1 FP01-1 17 ELBOW ............................................................................................. 2 2 FP05-010 FITTING 3/8 TUBE T O 1/4 NP ........................................................ 2 3 65173 MANIFOLD TUBE – LEFT ................. ...

  • Henny Penny PFG-690 - page 84

    Model 690 Figur e & Item No. Part No. Description Qty . 3-10 BURNER TUBES 1 54480 BRACKET ASSY – HIGH LIMIT SENSING BULB ................... 3 2 62051 CLIP – SPREADER – HEA T TUBE ............................................. 6 3 53670 SP ACER – HIGH LIMIT ............................................................... 1   4 16 ...

  • Henny Penny PFG-690 - page 85

    Model 690 Figur e & Item No. Part No. Description Qty . 3-1 1 CARRIER & RACKS 1 62183 CARRIER ASSY ............................................................................ 1 2 44782 RACK HALF SIZE – 8 HEAD FR YER ........................................ 5 3 35308 WELMENT - RACK HANDLE .................................................. ...

  • Henny Penny PFG-690 - page 86

    Model 690 Figur e & Item No. Part No. Description Qty . 3-12 V ACUUM SWITCH 1 60202 TUBE-V ACUUM SWITCH ................................................................ 1   2 14240 KIT - V ACUUM SWITCH - VERITCAL ........................................... 1   2 72514 V ACUUM SWITCH – VER TICAL (Included in 14240 Kit) ...... ...

  • Henny Penny PFG-690 - page 87

    Model 690 810 3-23 3-13. DEADWEIGHT & SOLENOID ASSEMBL Y (SN: AP082029 & ABOVE) ...

  • Henny Penny PFG-690 - page 88

    Model 690 Figure & Item No. Part No. Description Qty . 3-13 DEADWEIGHT & SOLENOID ASSY (SN: AP082029 & ABOVE)   1 16910 PRESSURE GAUGE .......................................................... 1   2 59742 RELIEF V AL VE ASSY ....................................................... 1 3 FP01-127 ELBOW , STREET , ½ X ½, ...

  • Henny Penny PFG-690 - page 89

    Model 690 810 3-25 Figure & Item No. Part No. Description Qty . 3-14A STEAM BOX & HOSE ASSY (SN: AP082029 & UP) 1 35686 TUBE, DW T O EXHAUST ST ACK SS ............................ 1 2 MS01-297 HOSE CLAMP , SS - .500 – 1.062 DID ............................. 4 3 70569 TUBE, EXHAUST CONNECT ......................................... 1 4 ...

  • Henny Penny PFG-690 - page 90

    Model 690 3-26 810 FIGURE 3-14B. STEAM BOX & HOSE ASSEMBL Y SN: AP0802028 & BELOW ...

  • Henny Penny PFG-690 - page 91

    Model 690 Figure & Item No. Part No. Description Qty . 3-14B STEAM BOX & HOSE ASSEMBL Y (SN: AP0802028 & BELOW) 1 56335 BRACKET – CONDENSA TE BOX ................................................... 1 2 21878 TUBING – STEAM EXHAUST ......................................................... 1 2 42508 TUBING – STEAM EXHAUST -UNITS BUI ...

  • Henny Penny PFG-690 - page 92

    Model 690 3-28 708 FIGURE 3-15. FLUE ASSEMBL Y & BLOWER SN: AP0802028 & BELOW ...

  • Henny Penny PFG-690 - page 93

    Model 690 Figur e & Item No. Part No. Description Qty . 3-15 FLUE ASSEMBL Y & BLOWER (SN: AP0802028 & BELOW) 1 55681 FLUE ASSY – WELDMENT ........................................................ 1 2 55783 BRACKET – FLUE RET AINING ................................................. 1 3 SC03-005 SCREW SD #8 X 1/2 PH PHD ............... ...

  • Henny Penny PFG-690 - page 94

    Model 690 3-30 810 FIGURE 3-16. FLUE ASSEMBL Y & BLOWER SN: AP0802029 & ABOVE 6 ...

  • Henny Penny PFG-690 - page 95

    Model 690 Figur e & Item No. Part No. Description Qty . 3-16 FLUE ASSEMBL Y & BLOWER (SN: AP0802029 & ABOVE) 1 70582 FLUE ASSY – WELDMENT ........................................................ 1 2 SC02-041 #8-32 X 7/16 PH IND XTRNL TRX ............................................. 1 3 NS02-002 NUT KEPS 1/4-20 C ..................... ...

  • Henny Penny PFG-690 - page 96

    Model 690 3-32 905 FIGURE 3-17. SOLENOID V AL VE ASSEMBL Y ...

  • Henny Penny PFG-690 - page 97

    Model 690 Figur e & Item No. Part No. Description Qty . 3-17 SOLENOID V AL VE ASSEMBL Y 1 17121 V AL VE, SOLENOID 120V , 60 Hz ................................................ 1 1 18721 V AL VE, SOLENOID 208-240V , 60 Hz ......................................... 1 1 18724 V AL VE, SOLENOID 208-240V , 50 Hz ...................................... ...

  • Henny Penny PFG-690 - page 98

    Model 690 3-34 1008 FIGURE 3-18. FR YPOT & DRAIN PIPING ...

  • Henny Penny PFG-690 - page 99

    Model 690 Figur e & Item No. Part No. Description Qty . 3-18 FR YPOT & DRAIN PIPING   4 14330 PROBE ASSY – DOMESTIC ........................................................... 1   4 14266 KIT -CE PROBE CONNECT OR RETROFIT (probe not included) .. 1 (CE units built prior to NOV . 1, 1999) 5 16226 NIPPLE 1/2 X 3-1/2 ....... ...

  • Henny Penny PFG-690 - page 100

    Model 690 3-36 708 FIGURE 3-19. LIFT BEAM & SHROUDS SN: AP0802028 & BELOW ...

  • Henny Penny PFG-690 - page 101

    Model 690 Figur e & Item No. Part No. Description Qty . 3-19 LIFT BEAM & SHROUDS (SN: AP0802028 & BELOW) 1 55678 ASSY – I-BEAM/LIFT FRAME ................................................... 1 2 51548 . LIFT I-BEAM ............................................................................. 1 3 55677 . LIFT FRAME ASSY – WELDMENT ... ...

  • Henny Penny PFG-690 - page 102

    Model 690 3-38 708 FIGURE 3-20. COUNTERWEIGHT & PULLEY SYSTEM (SN: AP0802028 & BELOW) ...

  • Henny Penny PFG-690 - page 103

    Model 690 Figur e & Item No. Part No. Description Qty . 3-20 COUNTER WEIGHT & PULLEY SYSTEM (SN: AP0802028 & BELOW) 2 51677 PULLEY PLA TE ............................................................................ 1 3 35962 BRACKET/WHEEL ASSY ........................................................... 2   4 35207 CABLE ....... ...

  • Henny Penny PFG-690 - page 104

    Model 690 3-40 708 Figure & Item No. Part No. Description Qty . 3-21 COUNTER WEIGHT SYSTEM (SN: AP0802029 & ABOVE) 1 35026 ARM, LID SUPPOR T ........................................................ 2   2 35207 CABLE ............................................................................... 2 3 NS01-025 NUT , HEX 5/16-18 SS ... ...

  • Henny Penny PFG-690 - page 105

    Model 690 1004 3-41 Figure 3-22. F AST Ready Parts ...

  • Henny Penny PFG-690 - page 106

    Model 690 Figure & Item No. Part No. Description Qty . 3-22 F AST READY P AR TS 1 66287 ASSY - 392/692 - 120V F AST HEADER .................. 1 1 66288 ASSY - 392/692 - 230V F AST HEADER - CE .......... 1 1 66385 ASSY - 392/692 - 220-240V F AST HEADER ........... 1 1 66241 STUD ASSY - 392/692 CONTROL PNL .................. 1 1 66296 STUD ASSY - ...

Fabricant Henny Penny Catégorie Fryer

Les documents que nous recevons du fabricant de l'appareilHenny Penny PFG-690 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Henny Penny
- manuels d’utilisations PFG-690
- fiches produit Henny Penny
- dépliants
- ou étiquettes-énergie Henny Penny PFG-690
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Henny Penny PFG-690.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Henny Penny PFG-690, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Henny Penny PFG-690. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Henny Penny PFG-690.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Henny Penny PFG-690, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Henny Penny PFG-690 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Henny Penny PFG-690.

Le manuel d’utilisation complet Henny Penny, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Henny Penny PFG-690 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Henny Penny PFG-690, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lHenny Penny PFG-690 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Henny Penny PFG-690 - qui devraient nous aider dans les premières étapes lors de l'utilisation Henny Penny PFG-690
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Henny Penny PFG-690
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Henny Penny PFG-690 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Henny Penny PFG-690?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Henny Penny PFG-690, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Henny Penny PFG-690 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)