Français dropdown-ico

Manuel d’utilisation Icom iPW1

24 pages 0.81 mb
Télécharger

Aller à la page of 24

Summary
  • Icom iPW1 - page 1

    iPW1 iPW1EURO HF/50 MHz ALL BAND 1 kW LINEAR AMPLIFIER INSTRUCTION MANUAL ...

  • Icom iPW1 - page 2

    R W ARNING HIGH VOL T AGE! NEVER attach an antenna or internal antenna connector dur- ing transmission. This may result in an electrical shock or burn. R W ARNING! NEVER carry the linear amplifier by yourself. At least two persons must carry the linear amplifier since it weights approx. 25 kg (55 lb). R W ARNING! NEVER apply AC voltage until the ...

  • Icom iPW1 - page 3

    IMPORT ANT ...................................................... i PRECAUTION ................................................... i EXPLICIT DEFINITIONS ................................. ii T ABLE OF CONTENTS .................................. ii SUPPLIED ACCESSORIES ............................ ii 1 P ANEL DESCRIPTION ............................ ...

  • Icom iPW1 - page 4

    1 1 P ANEL DESCRIPTION ■ Front panel and remote controller 0 100 250 500 1K 1.5 K 0 TEMP ALC ALC adj SWR 0 1 1.5 2 3 10 20 30 40 50 60 V D HOT I D Po 10 20 30 40 50 60 W A METER-1 METER-2 P o TEMP I D V D ALC SWR DOWN 1 . 8 3 . 5 7 1 0 1 4 1 8 2 1 2 42 85 0 U P ANT INPUT AUTO TRANSMIT TUNER AMP/ PROTECT POWER V 1 2 1 2 3 4 HF/50MHz ALL BAND 1kW L ...

  • Icom iPW1 - page 5

    2 1 P ANEL DESCRIPTION q POWER SWITCH [POWER] (p. 12) Push momentarily to turn power ON. w TRANSMIT INDICA TOR [TRANSMIT] (p. 16) Lights green while transmitting. During transmission, a humming may sound depending on the output power . This is caused by the large current produced by the power sup- ply and does not indicate equipment malfunc- tion. ...

  • Icom iPW1 - page 6

    3 1 P ANEL DESCRIPTION ■ Rear panel q OUTPUT ANTENNA CONNECTORS [ANT1] – [ANT4] (p. 6) Accept a 50 Ω antenna with a PL-259 connector . w ACCESSOR Y SOCKET -1 [ACC-1] ACCESSOR Y SOCKET -2 [ACC-2] Enable connection to Icom exciters (transceivers). - See the page at right for socket information. - The [ACC-2] socket is connected in parallel with ...

  • Icom iPW1 - page 7

    4 1 P ANEL DESCRIPTION D ACC-1 SOCKET D ACC-2 SOCKET (w/[EXCITER] is “ 1 ” ) The following descriptions are applied when the [EXCITER] switch is set to “ 1 ” (default). When [EXCITER] is set to “ 1&2, ” [ACC-2] functions the same as [ACC-1] above for the 2nd exciter . ACC-2 PIN NO. PIN NAME DESCRIPTION SPECIFICATIONS 18 V Regulated ...

  • Icom iPW1 - page 8

    5 2 INST ALLA TION AND CONNECTIONS ■ Unpacking After unpacking, immediately report any damage to the delivering carrier or dealer . Keep the shipping cartons. For a description and a diagram of accessory equip- ment included with the IC-PW1/EURO, see SUP- PLIED ACCESSORIES on p. ii of this manual. ■ Ferrite core installation The supplied cable ...

  • Icom iPW1 - page 9

    ■ Grounding T o prevent electrical shock, television interference (TVI), broadcast interference (BCI) and other prob- lems, ground the linear amplifier through the GROUND terminal on the rear panel. For best results, connect a heavy gauge wire or strap to a long earth-sunk copper rod. Make the distance between the GROUND terminal and ground as sh ...

  • Icom iPW1 - page 10

    ■ System interconnections 1 or 2 Icom 100 W HF transceivers can be connected as exciters to the IC-PW1/EURO. Non-Icom trans- ceivers can be used, however , band selection will not be synchronized for each exciter . See the following diagrams for making connections between the IC-PW1/EURO and an exciter (transceiv- er). See p. 5 for AC power cable ...

  • Icom iPW1 - page 11

    8 2 INST ALLA TION AND CONNECTIONS • Using a 13-pin ACC socket (IC-706 series) IC-PW1/EURO Ground Coaxial cable (supplied) ACC cable (supplied) Remote control cable (supplied) To an antenna ANT ACC-1 ANT1 REMOTE REMOTE INPUT1 GND GND IC-706 series ACC (13 pins) OPC-599 (optional) EXCITER 1 1&2 AC outlet (IC-PW1 : 100 – 120/220 – 240 V IC- ...

  • Icom iPW1 - page 12

    9 2 INST ALLA TION AND CONNECTIONS • Using 1 Icom and 1 non-Icom exciters (transceivers) NOTE: The speci fi cations for the SEND relay are 5 V DC 0.1 A. If this level is exceeded, a large external relay must be used. ANT ACC-1 ANT ACC(2) REMOTE REMOTE INPUT1 INPUT2 Connect ANT1 or ANT2 GND GND IC-PW1/EURO IC-756 Ground Coaxial cable (supplied) C ...

  • Icom iPW1 - page 13

    10 2 INST ALLA TION AND CONNECTIONS • Using non-Icom exciters (transceivers) when the IC-PW1/EURO ’ s power is OFF T o use the antenna selector of the IC-PW1/EURO while the power is OFF , follow 1 of 2 methods. (1) Supply the antenna selector power to the ACC-1 socket Supply the 13.8 V DC, 0.5 A to pin 7 of the [ACC-1]/ [ACC-2] socket. - Use [A ...

  • Icom iPW1 - page 14

    11 2 INST ALLA TION AND CONNECTIONS The control section of the linear ampli fi er can be sep- arated from the main body , doubling as a remote con- troller . It can be placed on the exciter or in another convenient place. q Disconnect the AC power cable. w Remove 8 screws from the sides of the linear ampli fi er , then lift up the top cover . e U ...

  • Icom iPW1 - page 15

    12 3 OPERA TION ■ Setting the ALC levels Before fi rst applying power , make sure all connec- tions required for your system are complete by refer- ring to chapter 2. Then, reset the linear ampli fi er using the following procedure. NOTE: Resetting CLEARS all programmed set- tings to default values. q Make sure the linear ampli fi er , exciter ...

  • Icom iPW1 - page 16

    13 3 OPERA TION The IC-PW1/EURO uses CI-V frequency data for automatic selection of the operating band. Program the exciter ’ s address to use this capability as follows: For non-Icom exciters, the IC-PW1/EURO cannot be controlled using the CI-V function, so this set- ting is not necessary . For transceivers which have multiple antenna con- necto ...

  • Icom iPW1 - page 17

    14 3 OPERA TION ■ Programming the CI-V address (continued) D Setting the IC-PW1/EURO ’ s address It is not necessary to change the IC-PW1/EURO ’ s default CI-V address of 54H. However , if desired, the address can be changed using the internal address switch illustrated below . It is not necessary to change the IC-PW1/EURO ’ s default CI-V ...

  • Icom iPW1 - page 18

    15 3 OPERA TION t Push [DOWN] to turn the position memory function for the [INPUT] select switch ON. • The band indicators, [1.8] – [50], light continuously . y Rotate the 1st exciter ’ s dial until the LED [INPUT z ] lights continuously . u T urn the 2nd exciter ’ s power ON. i Push [INPUT]. • LED [INPUT x ] blinks. o Rotate the 2nd exci ...

  • Icom iPW1 - page 19

    16 3 OPERA TION CAUTION: DO NOT operate the IC-PW1/EURO before adjusting the ALC levels properly with the [ALC adj1] and [ALC adj2] pots. (p. 1 1) It takes 15 sec. for CI-V line initial settings when several CI-V devices (more than 5) are connected to a CI-V line. For IC-781 users with other Icom CI-V transceivers: T urn the IC-781 power ON before ...

  • Icom iPW1 - page 20

    17 3 OPERA TION This linear ampli fi er has various protection circuits. D ALC circuit The ALC (Automatic Level Control) circuit automati- cally limits RF output power by controlling the input level of the exciter . This prevents transmission of dis- torted signals when the input signal level exceeds the allowable level. The ALC activates under th ...

  • Icom iPW1 - page 21

    18 4 MAINTENANCE ■ T roubleshooting The following chart is designed to help you correct problems which are not equipment malfunctions. If you are unable to locate the cause of a problem or solve it through the use of this chart, contact your nearest Icom Dealer or Service Center . PROBLEM Power does not come on when the [POWER] switch is pushed. ...

  • Icom iPW1 - page 22

    5 SPECIFICA TIONS 19 ■ General • Frequency coverage: 0 1.800 – 0 1.999 MHz 0 3.500 – 1 3.999 MHz 0 7.000 – 1 7.300 MHz 10.100 – 10.150 MHz 14.000 – 14.350 MHz 18.068 – 18.168 MHz 21.000 – 21.450 MHz 24.890 – 24.990 MHz * 1 28.000 – 29.700 MHz * 1 50.000 – 54.000 MHz * 1 The U.S.A. version can only be used the antenna tuner o ...

  • Icom iPW1 - page 23

    20 5 SPECIFICA TIONS INST ALLA TION NOTES For amateur base station installations it is recom- mended that the forwards clearance in front of the an- tenna array is calculated relative to the EIRP (Effective Isotropic Radiated Power). The clearance height below the antenna array can be determined in most cases from the RF power at the antenna input ...

  • Icom iPW1 - page 24

    1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan A-5449G-1EX- r Printed in Japan © 1997 – 2007 Icom Inc. Printed on recycled paper with soy ink. ...

Fabricant Icom Catégorie Car Amplifier

Les documents que nous recevons du fabricant de l'appareilIcom iPW1 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Icom
- manuels d’utilisations iPW1
- fiches produit Icom
- dépliants
- ou étiquettes-énergie Icom iPW1
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Icom iPW1.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Icom iPW1, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Icom iPW1. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Icom iPW1.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Icom iPW1, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Icom iPW1 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Icom iPW1.

Le manuel d’utilisation complet Icom, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Icom iPW1 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Icom iPW1, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lIcom iPW1 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Icom iPW1 - qui devraient nous aider dans les premières étapes lors de l'utilisation Icom iPW1
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Icom iPW1
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Icom iPW1 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Icom iPW1?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Icom iPW1, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Icom iPW1 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)