-
System Works 99101100 - page 1
REV. F 5-1-01 1 P/N 99101100 T able of Contents SECTION I. PUMP SAFETY INSTRUCTIONS ------------------------------------------------------- 2 SECTION II. HOW YOUR FIL TER WORKS ----------------------------------------------------------- 2 SECTION III. CHECK V AL VE INST ALLA TION INSTRUCTIONS ----------------------------------- 3 SECTION IV . INST ...
-
System Works 99101100 - page 2
P/N 99101100 2 REV. F 5-1-01 SECTION I. PUMP SAFETY INSTRUCTIONS When installing and using this electrical equipment, basic safety precautions should always be followed, including the following: 1 . READ AND FOLLOW ALL INSTRUCTIONS. 2 . WARNING - To reduce the risk of injury, do not permit children to use this product unless they are closely superv ...
-
System Works 99101100 - page 3
REV. F 5-1-01 3 P/N 99101100 SECTION III. CHECK VALVE INSTALLATION INSTRUCTIONS A . INSTALLATION 1 . Turn the pump off, shut off any automatic controls to assure that the system is not inadvertently started during servicing. 2 . Open the High Flow™ manual air relief valve. 3 . Plug the suction line by inserting a rag into the skimmer port, or if ...
-
System Works 99101100 - page 4
P/N 99101100 4 REV. F 5-1-01 6 . Insert the Check Valve into the outlet port approximately 3/4" to 1" deep making sure the rubber diaphragm facing outward (towards you), see Diagram 1. 7 . Reconnect the return hose to the outlet port and tighten the union fitting. 8 . Replace the drain cap. 9 . Remove the rag from the skimmer or open the ...
-
System Works 99101100 - page 5
REV. F 5-1-01 5 P/N 99101100 5 . Do not mount electrical controls (on/off switches, timer, etc.) over the filter. You need to be able to stand clear of the filter when starting the pump. 6 . Attach the hair and lint pot to the front of the pump. This is an O-ring seal fitting that requires hand tightening only. (OVER TIGHTENING CAN RESULT IN DAMAGE ...
-
System Works 99101100 - page 6
P/N 99101100 6 REV. F 5-1-01 SECTION V. INITIAL START-UP AND RESTART INSTRUCTIONS. 1 . Be sure all connections have been made and are secure. 2 . Make sure the hair and lint pot of the pump is filled with water. (FAILURE TO FILL THE HAIR AND LINT POT WITH WATER WILL RESULT IN DAMAGE TO THE PUMP AND PUMP SEAL). 3. OPEN THE HIGH FLOW MANUAL AIR RELIE ...
-
System Works 99101100 - page 7
REV. F 5-1-01 7 P/N 99101100 8 . Remove the CARTRIDGE ELEMENT assembly from the filter body by using the lifting handles and pulling straight up. 9 . Remove the CARTRIDGE ELEMENT from the core assembly by placing your middle fingers into cloth area and using your thumbs on top of the lifting handles and pressing until the CARTRIDGE ELEMENT is loose ...
-
System Works 99101100 - page 8
P/N 99101100 8 REV. F 5-1-01 SECTION VII. WINTERIZING THE FILTER 1 . In areas that have freezing winter temperatures, the pool equipment must be winterized to protect it from damage. 2 . With the pump turned off, open the High Flow™ manual air relief valve. 3 . Remove the drain port cap, and allow the filter to drain completely. 4 . Remove the dr ...
-
System Works 99101100 - page 9
REV. F 5-1-01 9 P/N 99101100 SECTION IX. TROUBLE SHOOTING Problem Cause Remedy Pool water not 1. Pool chemistry not adequate to inhibit algae growth. Maintain pool chemistry or consult pool service technician . sufficiently clean. 2. Inadequate turnover rate. Run system for longer time or consult dealer or pool service technician. Higher filter pre ...
-
System Works 99101100 - page 10
P/N 99101100 10 REV. F 5-1-01 3 . SHAFT SEAL - (rotary seal). The shaft seal consists of two parts: a. Rotating ceramic seal, press fitted into the impeller. b. A stationary spring loaded seal, press fitted into the rear of the volute. 4 . THE ELECTRIC MOTOR. a. The electric motor should be protected from foreign matter, water splashing, hosing, an ...
-
System Works 99101100 - page 11
REV. F 5-1-01 11 P/N 99101100 Replacement Parts Find Part Description No. No. 1 98209800 High Flow Manual Air Relief Valve 2 53003201 Pressure Gauge 3 178553 Lid, 50/100 Sq./Ft. 3 178561 Lid, 75 Sq./Ft. 4 59052900 Locking Ring Assy. 5 87300400 Body O-ring 6 59016200 Air Bleed Sock Kit 7 59053500 Center Core, 50 Sq./Ft. 7 59053600 Center Core, 75 Sq ...
-
System Works 99101100 - page 12
P/N 99101100 12 REV. F 5-1-01 SECTION XI. TECHNICAL DATA (continued) B. MAXIM PUMP Find Part Description No. No. 1 98206400 Plug, ¼ in. with O-ring 2 57006500 O-ring 3 39102503 Volute, S Series, vertical 4 39701200 Seal, shaft 5 39104600 Impeller,½ hp 5 39153100 Impeller, ¾ hp 5 39153200 Impeller, 1 hp 5 39153400 Impeller, 1½ hp 5 39153500 Impe ...
-
System Works 99101100 - page 13
REV. F 5-1-01 13 P/N 99101100 SECTION XI. TECHNICAL DATA, (continued) C. DYNAMO PUMP D Y N A M O C OO SNAP TAB SNAP TAB MOTOR - SEE NOTE 1 SNAP TAB SLOT 18 26 25 24, 24A 20 21 27 19 23 22 12 17 13 14 15 11 10 16 9 9 7 8 6 5 4 3 2 1 * * * Motors 1 35-6471 ¾ A std. 48 frame thru-blt 115 only 1 35-6472 1 A std. 48 frame thru-blt 115 only 1 35-6469 1 ...
-
System Works 99101100 - page 14
P/N 99101100 14 REV. F 5-1-01 15-5118 2 5 ft. cord and plug 15-5370 2 5 ft. cord and plug, CSA approved 15-5234 3 ft. cord with twist lock plug 35-2245 Strain relief bushing for cords 15-5297 P hoto sensor add-on 2 3 35-4650 B ody - motor enclosure 2 4 35-4656 C a p - motor enclosure 2 5 15-4716 S crew - #10 self-tapping 2 6 15-5371 C ord - 25 ft. ...
-
System Works 99101100 - page 15
REV. F 5-1-01 15 P/N 99101100 ...
Avez-vous une question à propos de System Works 99101100?
Utiliser le formulaire ci-dessous
Si vous n’avez pas résolu votre problème avec System Works 99101100, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec System Works 99101100 il est probable qu’il a envie de partager la façon de le résoudre.