Manuel d’utilisation Honda Automobiles HRC215

60 pages 1.58 mb
Télécharger

Aller à la page of 60

Summary
  • Honda Automobiles HRC215 - page 1

    HONDA Power 1 Equipment Owner’s Manual Rotary Mower HRC215 ...

  • Honda Automobiles HRC215 - page 2

    ...

  • Honda Automobiles HRC215 - page 3

    Thank you for purchasing a Honda rotary mower. This manual describes operation and maintenance of the Honda HFlC215PXA rotary mower. All information in this publication is based on the latest product information available at the time of printing. Honda Power Equipment Mfg., Inc reserves the right to make changes at any time without notice and witho ...

  • Honda Automobiles HRC215 - page 4

    CONTENTS 1. SAFETY .......................................... 4 Safety Label Locations. ............................. 4 Safety Information. ................................ 5 Important Message to Parents ........................ 7 2. COMPONENT IDENTIFICATION . . . . . . . . . . . . . . . . . . . . . . . . . 8 3. CONTROLS.. ......................... ...

  • Honda Automobiles HRC215 - page 5

    CONTENTS 7. MOWING RECOMMENDATIONS . . . . . . . . . . . . . . . . . . . . . . . . 29 8.TRANSPORTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 9. MAINTENANCE .................................... 33 Maintenance Schedule ............................. 33 Engine Oil Change ................................ 34 Air Cleaner S ...

  • Honda Automobiles HRC215 - page 6

    1. SAFETY SAFETY LABEL LOCATIONS Read all safety instructions before operating the mower. UNDER NORMAL USAGE, THIS BAG MATERIAL IS SUBJECT TO DETERIORATION AND WEAR, AND SHOULD BE CHECKED FREDUENTLY FOR BAG REPUGEMENT. THIS BAG CONFORMS TO A.N.S.I. STANDARD 871.1, ANY REPLACEMENT MUST MEET THIS STANDARD. I DO NOT START UNLESS GUARD IS CLOSED OR BAG ...

  • Honda Automobiles HRC215 - page 7

    4. SAFETY SAFETY INFORMATION For your safety and the safety of others, pay special attention to these precautions: Operator Responsibility l Know how to stop the engine quickly in case of emergency. Understand the use of all controls. l Be sure that anyone who operates the lawn mower receives proper instruction. Allowing anyone, especially children ...

  • Honda Automobiles HRC215 - page 8

    1. SAFETY Fire and Bum Hazards Gasoline is extremely flammable, and gasoline vapor can explode. Use extreme care when handling gasoline. KEEP OUT OF REACH OF CHILDREN. l Refuel in a well-ventilated area with the engine stopped. Keep flames and sparks away, and do not smoke in the area. l Refuel carefully to avoid spilling fuel. Avoid overfilling th ...

  • Honda Automobiles HRC215 - page 9

    1. SAFETY IMPORTANT MESSAGE TO PARENTS YOUR CHILDREN’S SAFETY IS VERY IMPORTANT to Honda. That’s why we urge you to read this message before letting your youngster operate this lawn mower. Lawn mowers are tools, not toys. As with any equipment, bad judgment can result in serious injuries. You can help prevent accidents by making good decisions ...

  • Honda Automobiles HRC215 - page 10

    2. COMPONENT IDENTIFICATION ROTO-STOP LEVER ROTO-STOP BUTTON THROTTLE LEVER / GRASS RAG CUTTING HEIGHT ADJUSTMENT LEVER CUTTING HEIGHT ADJUSTMENT LEVER CUTTER DECK 8 ...

  • Honda Automobiles HRC215 - page 11

    I 2. COMPONENT IDENTIFICATION ROTO-STOP BUTTON ROTO-STOP LEVER I RECOIL STARTER LE ENGINE SERIAL NUMBER ’ CUTTING HEIGHT AIR CLEANER ADJUSTMENT / LEVER CARBURETOR FUEL VALVE Record the frame and engine serial numbers for your reference. Refer to the serial numbers when ordering parts, and when making technical or warranty inquiries (see page ...

  • Honda Automobiles HRC215 - page 12

    3. CONTROLS FUEL VALVE The fuel valve opens and closes the connection between the fuel tank and the carburetor. The fuel valve must be in the ON position for the engine to run. When the mower is not in use, turn the fuel valve to the OFF position to prevent the possibility of carburetor flooding, and to reduce the possibility of fuel leakage m Gaso ...

  • Honda Automobiles HRC215 - page 13

    3. CONTROLS RDTO-STOP LEVER I The ROTO-STOP lever operates the blade brake/clutch mechanism. It is used to start and stop the blade. To put the blade into operation, press the button on top of the ROTO-STOP lever, then push the lever forward and hold it against the handlebar. Releasing the ROTO-STOP lever will stop the blade Operate the ROTO-STOP l ...

  • Honda Automobiles HRC215 - page 14

    3. CONTROLS CUTTING HEIGHT ADJUSTMENT LEVERS B The blade can cause serious injury. Stop the engine before adjusting cutting height. There are five cutting height settings: 1 in (2.8 cm), l-1/2 in (4.1 cm), 2 in (5.3 cm), 2-l/2 in (6.5 cm), and 3 in (7.7 cm). These are approximate figures, as the actual height of cut grass will vary with lawn and so ...

  • Honda Automobiles HRC215 - page 15

    4. ATTACHMENTS Honda HRC215 mowers are provided with a grass bag as standard equipment. You can operate the mower with the grass bag (or optional hard-shell grass catcher) installed to collect the grass clippings, or with the grass bag removed (or optional side-discharge chute installed) if you wish to leave the grass clippings on the lawn. When at ...

  • Honda Automobiles HRC215 - page 16

    4. ATTACHMENTS A hard-shell grass catcher, and a side-discharge chute, are available from authorized Honda lawn mower dealers. They attach to the cutter deck in place of the standard grass bag. HARD-SHELL GRASS CATCHER (optional) SIDE-DISCHARGE CHUTE (optional) SIDE DISCHARGE CHUTE 14 ...

  • Honda Automobiles HRC215 - page 17

    5. PRE-OPERATION CHECK Check the following items before starting the engine BLADE Turn the fuel valve OFF, and tilt the mower to the right, so the carburetor side is up. NOTE: Hard starting and fuel leakage may result if the mower is tilted with the carburetor side down. Inspect the blade for wear and damage. BLADE BOLTS NORMAL EXCESSIVELY BENT CRA ...

  • Honda Automobiles HRC215 - page 18

    5. PRE-OPERATION CHECK GRASS BAG Check that the grass bag is in good condition and not clogged. A clogged grass bag will not collect grass efficiently. When the bag needs cleaning, wash it with a garden hose, and allow it to dry thoroughly before use; a wet bag will clog quickly. The grass bag wears during normal use and will eventually require rep ...

  • Honda Automobiles HRC215 - page 19

    5. PRE-OPERATION CHECK ENGINE OIL Check the engine oil level with the engine stopped and the mower on a level surface. 1. Remove the oil filler cap, and wipe the dipstick clean. 2. Insert the dipstick into the oil filler neck, but do not screw it in. 3. Check the oil level shown on the dipstick. If near the lower level, fill to the upper level with ...

  • Honda Automobiles HRC215 - page 20

    FUEL Fuel tank capacity: 0.26 US gal (1.0 PI Remove the filler cap and check the fuel level. Refill the tank if the fuel level is low. Refuel carefully to avoid overfilling or spilling fuel. There should be no fuel in the filler neck. m Gasoline is extremely flammable, and gasoline vapor can explode, causing serious injury or death. Use extreme car ...

  • Honda Automobiles HRC215 - page 21

    5. PRE-OPERATION CHECK Fuel Recommendation Pump octane rating: 86 or higher. We recommend unleaded fuel because it produces fewer engine and spark plug deposits and extends exhaust system life Never use stale or contaminated gasoline or an oil/gasoline mixture. Avoid getting dirt or water in the fuel tank. Occasionally you may hear light “spark k ...

  • Honda Automobiles HRC215 - page 22

    5. PRE-OPERATION CHECK AIR CLEANER Check that the air filter is clean and in good condition. A dirty air filter will restrict air flow to the carburetor, reducing engine performance A damaged air filter will allow dirt to enter the engine, causing rapid engine wear. 1. Remove the cover screws, then remove the air cleaner cover. 2. Inspect the paper ...

  • Honda Automobiles HRC215 - page 23

    5. PRE-OPERATION CHECK CUTTING HEIGHT Check the cutting height settings, and make any necessary adjustments (see page 12). Set all four adjusting levers to the same cutting height position, m The blade can cause serious injury. Stop the engine before adjusting cutting height. ADJUSTING LEVERS 21 ...

  • Honda Automobiles HRC215 - page 24

    STARTING THE ENGINE If you run the engine in an area that is confined, or even partially enclosed, the air can become contaminated with a dangerous amount of exhaust gas. FUEL VALVE B Exhaust contains pois- onous carbon monoxide, a colorless and odorless gas. Breathing exhaust can cause loss of consciousness and may lead to death. To keep exhaust g ...

  • Honda Automobiles HRC215 - page 25

    6. OPERATION 3. Operate the starter. NOTE: Always release the ROTO-STOP lever before starting the engine If the blade drive is engaged, extra effort will be required to operate the starter. Place your foot on the step of the cutter deck. Pull the starter grip lightly until you feel resistance, then pull briskly. When the engine starts, return the s ...

  • Honda Automobiles HRC215 - page 26

    4. When the engine warms up, move the throttle lever away from the CHOKE position. Set the lever in FAST ( b ) position for mowing, or in SLOW ( -1 position for idling. THROTTLE LEVER NOTE: If restarting a warm engine in the CHOKE position, move the throttle lever away from CHOKE as soon as the engine starts. ---- CLEARING A FLOODED ENGINE If the e ...

  • Honda Automobiles HRC215 - page 27

    6. OPERATION MOWER OPERATION To mow, set the throttle lever in the FAST ( @ 1 position, press the button on top of the ROTO-STOP lever, then move the ROTO-STOP lever forward and hold it against the handlebar. The blade will turn while the ROTO-STOP lever is held forward. NOTE: For best grass cutting and bagging performance, and to avoid stalling th ...

  • Honda Automobiles HRC215 - page 28

    6a OPERATiON m If the mower tilts or overturns, the blade will be exposed; that will increase the risk of injury from blade contact and from thrown objects and debris. For your safety, keep all four wheels on the ground, and be careful not to lose your footing and your control of the mower. Keep a firm grip on the handlebar, and walk, never run, wi ...

  • Honda Automobiles HRC215 - page 29

    6. OPERATION STOPPING THE ENGINE 1. Release the ROTO-STOP lever. 2. Move the throttle lever to the STOP position. STOP When the mower is not in use, turn the fuel valve to the OFF position to prevent the possibility of carburetor flooding, and to reduce the possibility of fuel leakage B Gasoline is extremely flammable, and gasoline vapor can explod ...

  • Honda Automobiles HRC215 - page 30

    6. OPERATION HIGH ALTITUDE OPERATION At high altitude, the standard carburetor air-fuel mixture will be too rich. Performance will decrease, and fuel consumption will increase. A very rich mixture may also foul the spark plug and cause hard starting. High altitude performance can be improved by installing a smaller diameter main fuel jet in the car ...

  • Honda Automobiles HRC215 - page 31

    7. MOWING RECOMMENDATIONS A cutting height of l-1/2 in (4.1 cm) or 2 in (5.3 cm) is appropriate for most lawns during cool weather. A higher cut may be needed to protect the lawn during hot summer months. Consult a local nursery or lawn & garden center for advice about specific types of grasses and growing conditions in your area. k Most grasse ...

  • Honda Automobiles HRC215 - page 32

    7. MOWING RECOMMENDATIONS For best results, start at the outer edges of the lawn, and work toward the center in a clockwise direction. If you use the standard grass bag, or the optional hard-shell grass catcher, a clockwise mowing pattern, starting at the outer edges of the lawn, will give the best bagging performance, leaving the least amount of c ...

  • Honda Automobiles HRC215 - page 33

    7. MOWING RECOMMENDATIONS If the grass is not very thick or tall, you can mow a wide swath. Keep the wheels close to the swath line for maximum cutting width. i If the grass is very thick or tall, cutting a wide swath may slow or stall the engine, clog the cutter deck, and cause poor bagging performanca For thick or tall grass, cut a narrower swath ...

  • Honda Automobiles HRC215 - page 34

    8. TRANSPORTING B The engine and exhaust system become hot during operation and remain hot for a while after stopping. Contact with hot engine components can cause bums and can ignite some materials. t Avoid touching the engine or exhaust system for at least 15 minutes after the engine has stopped. Allow the engine to cool before transporting the m ...

  • Honda Automobiles HRC215 - page 35

    9. MAINTENANCE Wriodic maintenance and adjustment are necessary to keep the mower in good operating condition. Service and inspect according to the MAINTENANCE SCHEDULE. ‘J l To avoid carbon monoxide poisoning, shut the engine off before performing any maintenance. l To avoid serious burns, let the engine cool for at least 15 minutes before perfo ...

  • Honda Automobiles HRC215 - page 36

    9. MAINTENANCE ENGINE OIL CHANGE Engine oil capacity: 0.63 US qt (0.6 PI Drain the oil while the engine is warm to assure rapid and complete draining. e, 1. Place a suitable container under the cutter deck to catch the used oil. NOTE: Check to be sure the drain hole in the cutter deck is not clogged. s If necessary, remove grass and debris from the ...

  • Honda Automobiles HRC215 - page 37

    3. Install the oil drain bolt and tighten it securely. 4. Fill with the recommended oil (see c. page 17) to the upper level on the dipstick. Do not overfill. ; 5. Install the filler cap/dipstick. 6. Wipe the cutter deck drain channel clean to reduce dirt build-up when the mower is used. NOTE: Used motor oil may cause skin cancer if repeatedly left ...

  • Honda Automobiles HRC215 - page 38

    9. MAINTENANCE AIR CLEANER SERVICE A dirty air filter will restrict air flow to the carburetor, reducing engine performance. If you operate the mower in very dusty areas, clean the air filter more often than specified in the MAINTENANCE SCHEDULE (see page 34). 1 IMPORTANT NOTlCE 1 Operating the engine with no air filter, or a damaged air filter, wi ...

  • Honda Automobiles HRC215 - page 39

    9. MAINTENANCE J ELEMENT b 3 AIR FILTER FOAM ELEMENT 37 ...

  • Honda Automobiles HRC215 - page 40

    9. MAINTENANCE SPARK PLUG SERVICE Recommended spark plugs: NGK BPRBES ND IGEPR-U CHAMPION RN1211 1 IMPORTANT NOTICE 1 Spark plugs of the wrong heat range can cause engine damage. For good performance, the spark plug must be properly gapped and free of deposits. 1. 2. 3. 4. 5. 6. 7. Disconnect the spark plug cap, and remove any dirt from around the ...

  • Honda Automobiles HRC215 - page 41

    9. MAINTENANCE SPARK ARRESTER MAINTENANCE (optional equipment) The spark arrester must be serviced every 100 hours to keep it functioning as designed. m Touching the engine or exhaust system while hot can cause burns. Let the engine cool before servicing. 1. Remove the two nuts from the muffler shield, using a 10 mm wrench. 2. Remove the muffler sh ...

  • Honda Automobiles HRC215 - page 42

    RCITO-BTOP CABLE ADJUSTMENT 1. Measure free play at the tip of the lever, while holding the button down. Free play should be 3/4-l in. (20-25 mm). 2. If adjustment is necessary, loosen the lock nuts with a 10 mm wrench, and move the adjuster up or down as required. Tighten the lock nuts and recheck free play. NOTE: When mowing, check that the ROTO- ...

  • Honda Automobiles HRC215 - page 43

    9. MAINTENANCE THROTTLE CABLE ADJUSTMENT I 1. . . 2. 3. When the throttle lever is moved to the CHOKE position, the carburetor choke arm should move all the way counterclockwise, as far as it will go. Push the choke arm with your finger to check that it moved as far as it will go. If adjustment is necessary, loosen the throttle control cable lock n ...

  • Honda Automobiles HRC215 - page 44

    9. MAINTENANCE CARBURETOR ADJUSTMENT 1. Start the engine outdoors, and allow it to warm up to normal operating temperature 1 B Exhaust contains poisonous carbon monoxide, a colorless and odorless gas. Breathing exhaust can cause loss of consciousness and may lead to death. To keep exhaust gas from building up, provide adequate ventilation. 2. Set t ...

  • Honda Automobiles HRC215 - page 45

    SAG REMOVAL 1. 2. 3. 9. MAINTENANCE GRASS SAG CLEANING AND REPLACEMENT When the bag needs cleaning, wash it with a garden hose, and allow it to c dry completely before use; a wet grass bag will clog quickly. Replace a frayed, torn, or deteriorated i bag with a Honda replacement bag or its equivalent. Pull off one of the cap nuts, using pliers. Or p ...

  • Honda Automobiles HRC215 - page 46

    9. MAINTENANCE BLADE REMOVAL AND INSTALLATION When the blade needs sharpening or replacement, take the lawn mower to an authorized Honda lawn mower dealer. Or, if you have a torque wrench, you can remove and install the blade yourself. Wear heavy gloves to protect your hands. l Blade sharpening: To reduce the possibility of weakening the blade, or ...

  • Honda Automobiles HRC215 - page 47

    9. MAINTENANCE Blade Installation 1. Clean dirt and grass from the blade mounting area. rv 2. Position the blade and blade holder on the ROTO-STOP assembly, and install the blade bolts. NOTE: . l Be sure the blade is positioned right side up (rear edges turn upward; center hole rim projects downward). If the blade is installed upside down, the edge ...

  • Honda Automobiles HRC215 - page 48

    10. STORAGE Preparation for Storage When the mower will not be used for one month or longer, proper storage preparation will help to prevent rust and corrosion, and will make it easier to start the engine when the mower is removed from storage. I 1. Clean all surfaces of the mower, including the area underneath the cutter deck. Wear heavy gloves to ...

  • Honda Automobiles HRC215 - page 49

    10. STORAGE 4. For prolonged storage, perform these additional steps: For storage of 1 or 2 months: . For storage of 1 or 2 months, be sure the fuel tank is full. If partially filled, air in the tank will promote fuel oxidation and deterioration, resulting in bad fuel that may cause hard starting. Deteriorated fuel may also clog carburetor passages ...

  • Honda Automobiles HRC215 - page 50

    10. STORAGE For storage of more than 2 months (continued): d. Disconnect the fuel line from the fuel valve, and drain the fuel tank into an approved gasoline container. B . Gasoline is extremely flammable, and gasoline vapor can explode, causing serious injury or death. Use extreme care when handling gasoline. KEEP OUT OF REACH OF CHILDREN. a Remov ...

  • Honda Automobiles HRC215 - page 51

    10. STORAGE -2’ Cover the mower to keep out dust. NOTE: Plastic sheets should not be used as dust covers; they trap moisture under the covers, promoting rust and corrosion. Removal from Storage * Check all items described in the PRE-OPERATION CHECK section of this manual (pages 15-211. NOTE: l Fill the fuel tank with fresh gasoline If you keep a ...

  • Honda Automobiles HRC215 - page 52

    11. TROUBLESHOOTING ENGINE ENGINE WlLL NOT SWIT 1. Check control positiona POSf3Sl.E CAUSE Fuel valve OFF. Throttle lever in wrong oosition. 2. Check fuel. out of fuel. 3. Remove and inspect spsrk plug. 4. Take mower to dealer for service or repair. Sad fuel; mower stored without treating or draining gasoline or refueled with bad gas. Spark plug fa ...

  • Honda Automobiles HRC215 - page 53

    11. TROUBLESHOOTING GRASS CUlTlNG POOR CUT QuALlTY ORPOORCUlllNG PERFORMANCE POSSISIJ! WSE 1. Check that throttle Engine speed is too slow to lever is in FAST cut well. ( * ) position. 2. Reduce forward speed. 3. Check cutting height adjustment laws. 4. Check grass bag. 5. Check cutter deck and blade GRASS BAGGING POOR GRASS CORRECTfON I Move throt ...

  • Honda Automobiles HRC215 - page 54

    12. SPECIFICATIONS MOWER MODEL HRC215PXA Overall Lenath 66 in (167 cm) Width at cutter deck 22.2 in (56.5 cm) Maximum Height (cutting height 42 in (106 cm) adjusted to 3 in; 7.7 cm1 Minimum Height (cutting height 40 in (101 cm) adiusted to 1 in: 2.6 cm) Dry Weight Grass Bag Capacitv 112.5 (51 kg) 2.36 bushels; 21.9 US gal (63 PI -. Cutting Width 20 ...

  • Honda Automobiles HRC215 - page 55

    13. WIRING DIAGRAM PLUG ’ ’ y - IGNITION COIL 53 ...

  • Honda Automobiles HRC215 - page 56

    MEMO 54 ...

  • Honda Automobiles HRC215 - page 57

    14. WARRANTY SERVICE Owner Satisfaction .’ i Your satisfaction and goodwill are important to your dealer and to us. All Honda warranty details are explained in the Distributor’s Limited Warranty. Normally, any problems concerning,the product will be handled by your dealer’s service department. If you have a warranty problem that has not been ...

  • Honda Automobiles HRC215 - page 58

    Current customer service contact information: United States, Puerto Rico, and U.S. Virgin Islands: Honda Power Equipment dealership personnel are trained professionals. They should be able to answer any question you may have. If you encounter a problem that your dealer does not solve to your satisfaction, please discuss it with the dealership' ...

  • Honda Automobiles HRC215 - page 59

    . . ...

  • Honda Automobiles HRC215 - page 60

    31VB5BOO lPMlll6006912 00X31-VB5BOOO PRINTED IN U.S.A. I I I I I I I I I I ...

Fabricant Honda Automobiles Catégorie Lawn Mower

Les documents que nous recevons du fabricant de l'appareilHonda Automobiles HRC215 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Honda Automobiles
- manuels d’utilisations HRC215
- fiches produit Honda Automobiles
- dépliants
- ou étiquettes-énergie Honda Automobiles HRC215
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Honda Automobiles HRC215.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Honda Automobiles HRC215, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Honda Automobiles HRC215. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Honda Automobiles HRC215.

Manuel d’utilisation complet de l’appareil Honda Automobiles HRC215, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Honda Automobiles HRC215 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Honda Automobiles HRC215.

Le manuel d’utilisation complet Honda Automobiles, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Honda Automobiles HRC215 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Honda Automobiles HRC215, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lHonda Automobiles HRC215 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Honda Automobiles HRC215 - qui devraient nous aider dans les premières étapes lors de l'utilisation Honda Automobiles HRC215
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Honda Automobiles HRC215
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Honda Automobiles HRC215 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Honda Automobiles HRC215?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Honda Automobiles HRC215, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Honda Automobiles HRC215 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Commentaires (0)