Français dropdown-ico

Manuel d’utilisation Alliance Laundry Systems SX

78 pages 3.72 mb
Télécharger

Aller à la page of 78

Summary
  • Alliance Laundry Systems SX - page 1

    www .comlaundry .com CFS462N Par t No. 9001900 December 2005 Ser vice W asher -Extractor Cabinet Freestanding HX, SX and UX OPL Models Refer to P age 8 for Model Numbers ...

  • Alliance Laundry Systems SX - page 2

    ...

  • Alliance Laundry Systems SX - page 3

    9001900 1 © Copyr ight 2005, A lliance Laundry Systems LLC All righ ts reserv ed. No part of the con tents of this book may be reprod uced or transm itted in an y form or b y any m eans withou t the expressed writ ten consent of the pu blisher . © Copyright, Alliance Laundr y S ystems LLC – DO NO T COPY or TRAN S MIT Table of Contents Section 1 ...

  • Alliance Laundry Systems SX - page 4

    2 9001900 © Copyright, Alliance Laundr y S ystems LLC – DO NO T COPY or TRAN S MIT ...

  • Alliance Laundry Systems SX - page 5

    9001900 3 © Copyright, Alliance Laundr y S ystems LLC – DO NO T COPY or TRAN S MIT Section 1 Safety Information Throughout this manua l and on mach ine decals, yo u will f ind preca utionary statements ( “CA UTION, ” “W ARNING, ” and “D ANGER”) fol lo wed by specif ic in structions . These prec autions are intended f or the pe rsonal ...

  • Alliance Laundry Systems SX - page 6

    4 9001900 Section 1 Sa fety Inf ormation © Copyright, Alliance Laundr y S ystems LLC – DO NO T COPY or TRAN S MIT Alwa ys contac t your dea ler , distrib utor , service a gent or the man ufact urer about any problems or conditi ons you do not u nderstand. Important Safety Instructions 1. Read all instruc tions before using the washer-ex tractor. ...

  • Alliance Laundry Systems SX - page 7

    9001900 5 Section 1 Sa fety Inf ormation © Copyright, Alliance Laundr y S ystems LLC – DO NO T COPY or TRAN S MIT 6. Do not al low chil dren to p lay on or in a washer -extrac tor. Close su pervisio n of chi ldren is necessary when the washer-e xtracto r is used near childre n. 7. Before t he washer-ext ractor is r emoved from ser vice or disca ...

  • Alliance Laundry Systems SX - page 8

    6 9001900 Section 1 Sa fety Inf ormation © Copyright, Alliance Laundr y S ystems LLC – DO NO T COPY or TRAN S MIT Locating an Auth orized Service r Allianc e Laundry Sys tems is not r esponsibl e for persona l injury or proper ty damage re sulting fr om improper servic e. Re vie w all ser vice inf ormation b efore be ginnin g repairs . W arranty ...

  • Alliance Laundry Systems SX - page 9

    9001900 7 © Copyright, Alliance Laundr y S ystems LLC – DO NO T COPY or TRAN S MIT Section 2 Introduction Customer Service Allianc e Laundry Syste ms is not r esponsible f or personal injury or propert y damage re sulting fro m impro per service. Re vie w all s ervice i nformation befo re beginn ing repairs . If li teratu re o r rep lace men t p ...

  • Alliance Laundry Systems SX - page 10

    8 9001900 Section 2 I ntroducti on © Copyright, Alliance Laundr y S ystems LLC – DO NO T COPY or TRAN S MIT Model Identification Infor ma tion in thi s man ual is app lica ble to the se wa she r-extracto rs. HX18PVQM6 HX18PVQU6 HX18PVXM6 HX18PVXU6 HX25PVQM6 HX25PVQU6 HX25PVXM6 HX25PVXU6 HX35PVQM6 HX35PVQU6 HX35PVXM6 HX35PVXU6 HX55PVNU6 HX55PVQU6 ...

  • Alliance Laundry Systems SX - page 11

    9001900 9 T o reduce the risk of electrical shoc k, fire, e xplosion, serious inj ury or death: • Disconnect electrica l power to the washer -extractor bef ore servicing it. • Close the gas shut- off valve to the washer -e xtractor (when applicab le) bef ore servicing it. • Ne ver start the washer-e xtractor with an y guar ds/panels remo ved. ...

  • Alliance Laundry Systems SX - page 12

    10 9001900 Section 3 T roub leshootin g © Copyright, Alliance Laundr y S ystems LLC – DO NO T COPY or TRAN S MIT 1. WE-8 CONTROL HAS NO VISIBLE DISPLAY (P AND N-VOLTAGE MODELS) Is there voltage (200-240 Volts) out of the control transformer? Is there voltage (3 8 0-4 8 0 Volts) into the control transformer? The WE- 8 control has no visible displ ...

  • Alliance Laundry Systems SX - page 13

    9001900 11 Section 3 T ro ubleshooti ng © Copyright, Alliance Laundr y S ystems LLC – DO NO T COPY or TRAN S MIT Please refer to the f ollowing 2 pa ges for wiring diagram inf ormation. ...

  • Alliance Laundry Systems SX - page 14

    12 9001900 Section 3 T roub leshootin g © Copyright, Alliance Laundr y S ystems LLC – DO NO T COPY or TRAN S MIT WE-8 Cont rol Has No Vis ible Display (P and N-V o ltage M odels) (She et 1 of 2) NOTE: Refer to the wiring diagram supplied wi th your machi ne. 7 6 5 4 4 3 2 1 ...

  • Alliance Laundry Systems SX - page 15

    9001900 13 Section 3 T ro ubleshooti ng © Copyright, Alliance Laundr y S ystems LLC – DO NO T COPY or TRAN S MIT WE-8 Cont rol Has No Vis ible Display (P and N-V o ltage M odels) (She et 2 of 2) CFD3 S 063787600D ...

  • Alliance Laundry Systems SX - page 16

    14 9001900 Section 3 T roub leshootin g © Copyright, Alliance Laundr y S ystems LLC – DO NO T COPY or TRAN S MIT 2. WE-8 CONTROL HAS NO VISIBLE DISPLAY (Q AND X-VOLTAGE MODELS) Is there Voltage (120 Volts) into and out of the 3.15 Amp fuse? NO YES NO Reset and return (either by pulling or by twisting and pulling) the E-stop switch. If, after res ...

  • Alliance Laundry Systems SX - page 17

    9001900 15 Section 3 T ro ubleshooti ng © Copyright, Alliance Laundr y S ystems LLC – DO NO T COPY or TRAN S MIT Please refer to the f ollowing 2 pa ges for wiring diagram inf ormation. ...

  • Alliance Laundry Systems SX - page 18

    16 9001900 Section 3 T roub leshootin g © Copyright, Alliance Laundr y S ystems LLC – DO NO T COPY or TRAN S MIT WE-8 Co ntrol Has No Visible Dis play (Q and X-V oltage Models ) (Sheet 1 of 2) NOTE: Refer to the wiring diagram supplied wi th your machi ne. 6 ...

  • Alliance Laundry Systems SX - page 19

    9001900 17 Section 3 T ro ubleshooti ng © Copyright, Alliance Laundr y S ystems LLC – DO NO T COPY or TRAN S MIT WE-8 Co ntrol Has No Visible Dis play (Q and X-V oltage Models ) (Sheet 2 of 2) CFD5 S 3 3.15 A 4 5 3 1 2 ...

  • Alliance Laundry Systems SX - page 20

    18 9001900 Section 3 T roub leshootin g © Copyright, Alliance Laundr y S ystems LLC – DO NO T COPY or TRAN S MIT 3. NO FILL ANALYSIS CFD18 S NO NO Check the wiring between the main board and the water valve that has been programmed to turn on. Repair or replace the wiring as needed. Note: There may be a modular connector between the wire and the ...

  • Alliance Laundry Systems SX - page 21

    9001900 19 Section 3 T ro ubleshooti ng © Copyright, Alliance Laundr y S ystems LLC – DO NO T COPY or TRAN S MIT Please refer to the f ollowing 2 pa ges for wiring diagram inf ormation. ...

  • Alliance Laundry Systems SX - page 22

    20 9001900 Section 3 T roub leshootin g © Copyright, Alliance Laundr y S ystems LLC – DO NO T COPY or TRAN S MIT No Fill Analysis (Sheet 1 of 2) NOTE: Refer to the wiring diagram supplied wi th your machi ne. ...

  • Alliance Laundry Systems SX - page 23

    9001900 21 Section 3 T ro ubleshooti ng © Copyright, Alliance Laundr y S ystems LLC – DO NO T COPY or TRAN S MIT No Fill Analysis (Sheet 2 of 2) CFD1 9S 1 Hot Fill X18 - 75 3 2 2 3 3 3 3 3 1 Cold Fill X18 - 75 1 Hot Fill X100 - 135 1 Cold Fill X100 - 135 ...

  • Alliance Laundry Systems SX - page 24

    22 9001900 Section 3 T roub leshootin g © Copyright, Alliance Laundr y S ystems LLC – DO NO T COPY or TRAN S MIT 4. WATER RUNS CONTINUOUSLY INTO THE WASHER-EXTRACT OR CFD20 S 1 T urn the main power to the machine off. Does the water shut off? 2 YES Clean the valve or install a repair kit inside the valve if av ailable. If a repair kit isn ’ t ...

  • Alliance Laundry Systems SX - page 25

    9001900 23 Section 3 T ro ubleshooti ng © Copyright, Alliance Laundr y S ystems LLC – DO NO T COPY or TRAN S MIT Please refer to the f ollowing 2 pa ges for wiring diagram inf ormation. ...

  • Alliance Laundry Systems SX - page 26

    24 9001900 Section 3 T roub leshootin g © Copyright, Alliance Laundr y S ystems LLC – DO NO T COPY or TRAN S MIT W ater Runs Cont inuously into the Washer-Extractor (S heet 1 of 2 ) NOTE: Refer to the wiring diagram supplied wi th your machi ne. ...

  • Alliance Laundry Systems SX - page 27

    9001900 25 Section 3 T ro ubleshooti ng © Copyright, Alliance Laundr y S ystems LLC – DO NO T COPY or TRAN S MIT W ater Runs Cont inuously into the Washer-Extractor (S heet 2 of 2 ) CFD21 S 2 1 1 ...

  • Alliance Laundry Systems SX - page 28

    26 9001900 Section 3 T roub leshootin g © Copyright, Alliance Laundr y S ystems LLC – DO NO T COPY or TRAN S MIT 5. DOOR LOCK SWITCH ANALYSIS: DISPLAY SHOWS “DOOR ERROR” CFD1 99 3 S 1 The display reads “door error”. Check the wiring from the door terminal on the main board to the mole x plug (75-165 models only) and from the mole x plug ...

  • Alliance Laundry Systems SX - page 29

    9001900 27 Section 3 T ro ubleshooti ng © Copyright, Alliance Laundr y S ystems LLC – DO NO T COPY or TRAN S MIT Please refer to the f ollowing 2 pa ges for wiring diagram inf ormation. ...

  • Alliance Laundry Systems SX - page 30

    28 9001900 Section 3 T roub leshootin g © Copyright, Alliance Laundr y S ystems LLC – DO NO T COPY or TRAN S MIT Door Lock Swit ch Analysis: Display Sh ows “Door Er ror” (Sheet 1 of 2) NOTE: Refer to the wiring diagram supplied wi th your machi ne. ...

  • Alliance Laundry Systems SX - page 31

    9001900 29 Section 3 T ro ubleshooti ng © Copyright, Alliance Laundr y S ystems LLC – DO NO T COPY or TRAN S MIT Door Lock Swit ch Analysis: Display Sh ows “Door Er ror” (Sheet 2 of 2) CFD1 99 4 S UX75 1 2 3 ...

  • Alliance Laundry Systems SX - page 32

    30 9001900 Section 3 T roub leshootin g © Copyright, Alliance Laundr y S ystems LLC – DO NO T COPY or TRAN S MIT 6. DOOR LOCK SWITCH ANALYSIS: DISPLAY READS “PLEASE CLOSE DOOR” YE S 1 The display reads “ Please Close Door ” . Is the door closed? 2 Close the door . NO Check the orange/white and white/brown wires fr om the door terminal on ...

  • Alliance Laundry Systems SX - page 33

    9001900 31 Section 3 T ro ubleshooti ng © Copyright, Alliance Laundr y S ystems LLC – DO NO T COPY or TRAN S MIT Please refer to the f ollowing 2 pa ges for wiring diagram inf ormation. ...

  • Alliance Laundry Systems SX - page 34

    32 9001900 Section 3 T roub leshootin g © Copyright, Alliance Laundr y S ystems LLC – DO NO T COPY or TRAN S MIT Door Lock Switch Analysis: Displa y Reads “Please Close Door” (Sheet 1 of 2) NOTE: Refer to the wiring diagram supplied wi th your machi ne. ...

  • Alliance Laundry Systems SX - page 35

    9001900 33 Section 3 T ro ubleshooti ng © Copyright, Alliance Laundr y S ystems LLC – DO NO T COPY or TRAN S MIT Door Lock Switch Analysis: Displa y Reads “Please Close Door” (Sheet 2 of 2) CFD1 99 6 S UX75 1 1 2 ...

  • Alliance Laundry Systems SX - page 36

    34 9001900 Section 3 T roub leshootin g © Copyright, Alliance Laundr y S ystems LLC – DO NO T COPY or TRAN S MIT 7. DOOR LOCK SWITCH ANALYSIS: “DOOR WO N’T UNLOCK” 1 The display reads “ Please Open the Door ” , but the door can't be opened. 2 NO Check the black and white wires from the door terminal on the main board, through the ...

  • Alliance Laundry Systems SX - page 37

    9001900 35 Section 3 T ro ubleshooti ng © Copyright, Alliance Laundr y S ystems LLC – DO NO T COPY or TRAN S MIT Please refer to the f ollowing 2 pa ges for wiring diagram inf ormation. ...

  • Alliance Laundry Systems SX - page 38

    36 9001900 Section 3 T roub leshootin g © Copyright, Alliance Laundr y S ystems LLC – DO NO T COPY or TRAN S MIT Door L ock Switch Analysis: “Door W on’t Unlock” (She et 1 of 2) NOTE: Refer to the wiring diagram supplied wi th your machi ne. ...

  • Alliance Laundry Systems SX - page 39

    9001900 37 Section 3 T ro ubleshooti ng © Copyright, Alliance Laundr y S ystems LLC – DO NO T COPY or TRAN S MIT Door L ock Switch Analysis: “Door W on’t Unlock” (She et 2 of 2) CFD1 99 8 S UX75 1 1 3 2 3 ...

  • Alliance Laundry Systems SX - page 40

    38 9001900 Section 3 T roub leshootin g © Copyright, Alliance Laundr y S ystems LLC – DO NO T COPY or TRAN S MIT 8. NO OUTPUT VOLTAGE TO COMPONEN TS Figure 1 Component V oltage Reading P oints V oltage Reading Wa t e r Flush A Clear wire to Blue wire 220 V olts AC Hard Fill White/Black wire to Blue wire 220 V olts AC Hot Fill Red wire to Blue wi ...

  • Alliance Laundry Systems SX - page 41

    9001900 39 Section 3 T ro ubleshooti ng © Copyright, Alliance Laundr y S ystems LLC – DO NO T COPY or TRAN S MIT Please refer to the f ollowing 2 pa ges for wiring diagram inf ormation. ...

  • Alliance Laundry Systems SX - page 42

    40 9001900 Section 3 T roub leshootin g © Copyright, Alliance Laundr y S ystems LLC – DO NO T COPY or TRAN S MIT No Ou tput V olta ge to Co mpon ents ( She et 1 of 2 ) NOTE: Refer to the wiring diagram supplied wi th your machi ne. 1 2 2 2 2 1 ...

  • Alliance Laundry Systems SX - page 43

    9001900 41 Section 3 T ro ubleshooti ng © Copyright, Alliance Laundr y S ystems LLC – DO NO T COPY or TRAN S MIT No Ou tput V olta ge to Co mpon ents ( She et 2 of 2 ) CFD2001 S UX75 2 2 2 2 2 2 2 1 1 1 1 ...

  • Alliance Laundry Systems SX - page 44

    42 9001900 Section 3 T roub leshootin g © Copyright, Alliance Laundr y S ystems LLC – DO NO T COPY or TRAN S MIT 9. NO MOTOR OPERATION WITH NO AC DRIVE FAULT CFD2002 S 1 The motor does not operate and there are no apparent A C drive faults present. For single-phase models, is there volta ge (200 V olts AC) from L1 to L2 on the A C drive? For 3-p ...

  • Alliance Laundry Systems SX - page 45

    9001900 43 Section 3 T ro ubleshooti ng © Copyright, Alliance Laundr y S ystems LLC – DO NO T COPY or TRAN S MIT Please refer to the f ollowing 2 pa ges for wiring diagram inf ormation. ...

  • Alliance Laundry Systems SX - page 46

    44 9001900 Section 3 T roub leshootin g © Copyright, Alliance Laundr y S ystems LLC – DO NO T COPY or TRAN S MIT No Motor Operation With No A C Drive F ault (Sheet 1 of 2) NOTE: Refer to the wiring diagram supplied wi th your machi ne. 1 1 1 2 2 2 ...

  • Alliance Laundry Systems SX - page 47

    9001900 45 Section 3 T ro ubleshooti ng © Copyright, Alliance Laundr y S ystems LLC – DO NO T COPY or TRAN S MIT No Motor Operation With No A C Drive F ault (Sheet 2 of 2) CFD2003 S UX75 3 3 ...

  • Alliance Laundry Systems SX - page 48

    46 9001900 Section 3 T roub leshootin g © Copyright, Alliance Laundr y S ystems LLC – DO NO T COPY or TRAN S MIT 10. NO MOTOR OPERATION WITH AC DRIVE FAULT NO Symptom: The Motor Is Not Running And There Is An Apparent AC Drive Fault Present. YES Install a parameter unit and find the AC drive fault present. Refer to the “no motor operation (wit ...

  • Alliance Laundry Systems SX - page 49

    9001900 47 Section 3 T ro ubleshooti ng © Copyright, Alliance Laundr y S ystems LLC – DO NO T COPY or TRAN S MIT No Motor Operation W ith AC Drive Fault Operation Pane l Indication Name Description an d NO TES Check point Correctiv e action Overcurrent shut-off during accele ration When the in verter output cu rrent reaches o r exceeds app roxim ...

  • Alliance Laundry Systems SX - page 50

    48 9001900 Section 3 T roub leshootin g © Copyright, Alliance Laundr y S ystems LLC – DO NO T COPY or TRAN S MIT Brak e tra nsis tor alarm dete ction If a brake transistor fault occu rs due to excessiv ely large reg enerativ e energy from the motor, for example , that fa ult is dete cted to stop the in ver ter output. In this case, th e in verte ...

  • Alliance Laundry Systems SX - page 51

    9001900 49 Section 3 T ro ubleshooti ng © Copyright, Alliance Laundr y S ystems LLC – DO NO T COPY or TRAN S MIT Output ph ase failure prote ction This func tion stops the in verter output if o ne of the three phases (U, V , W) on the inv erter's outpu t side (load side) results in open p hase. • Check the wiring (Check the motor for a fa ...

  • Alliance Laundry Systems SX - page 52

    50 9001900 Section 3 T roub leshootin g © Copyright, Alliance Laundr y S ystems LLC – DO NO T COPY or TRAN S MIT 11. THE MOTOR IS RUNNING, BUT AT AN ABNORMAL SPEED Prelimina ry Checks: a. Check all elec trical connect ions betw een the “FREQ” plug on the mai n board and the AC drive . Refer to the schema tic supplie d with the machine for wi ...

  • Alliance Laundry Systems SX - page 53

    9001900 51 Section 3 T ro ubleshooti ng © Copyright, Alliance Laundr y S ystems LLC – DO NO T COPY or TRAN S MIT 12. NO SPIN NO NOTE: While performing this check, make sure that the washer-extractor is running with a normal-size load. YES When the WE- 8 computer is engaged in a high-speed extract (e.g., spin 1, spin 2, spin 3 or spin 4), is the ...

  • Alliance Laundry Systems SX - page 54

    52 9001900 Section 3 T roub leshootin g © Copyright, Alliance Laundr y S ystems LLC – DO NO T COPY or TRAN S MIT 13. MACHINE DID NOT FILL ALARM ANALYSIS CFD1 9 8 9S 1 Is there water coming in through the water supply lines? IS there volta ge (220 V olts) at the respective water valve that should be turning on? Check the main water v alve shut-of ...

  • Alliance Laundry Systems SX - page 55

    9001900 53 Section 3 T ro ubleshooti ng © Copyright, Alliance Laundr y S ystems LLC – DO NO T COPY or TRAN S MIT Please refer to the f ollowing 2 pa ges for wiring diagram inf ormation. ...

  • Alliance Laundry Systems SX - page 56

    54 9001900 Section 3 T roub leshootin g © Copyright, Alliance Laundr y S ystems LLC – DO NO T COPY or TRAN S MIT Machine Did No t Fill Alar m Analysis (Sh eet 1 of 2 ) NOTE: Refer to the wiring diagram supplied wi th your machi ne. 2 1 1 3 3 4 2 ...

  • Alliance Laundry Systems SX - page 57

    9001900 55 Section 3 T ro ubleshooti ng © Copyright, Alliance Laundr y S ystems LLC – DO NO T COPY or TRAN S MIT Machine Did No t Fill Alar m Analysis (Sh eet 2 of 2 ) CFD1990 S 063787600D ...

  • Alliance Laundry Systems SX - page 58

    56 9001900 Section 3 T roub leshootin g © Copyright, Alliance Laundr y S ystems LLC – DO NO T COPY or TRAN S MIT 14. EMPTY ALARM ANALYSIS CFD1 99 1 S 1 Check the drain v alve and drain plumbing for bloc kage. The display reads “ DID NO T EMPTY . ” Is there volta ge (220 V olts) at the drain valve? Is there volta ge (220 V olts) between the b ...

  • Alliance Laundry Systems SX - page 59

    9001900 57 Section 3 T ro ubleshooti ng © Copyright, Alliance Laundr y S ystems LLC – DO NO T COPY or TRAN S MIT Please refer to the f ollowing 2 pa ges for wiring diagram inf ormation. ...

  • Alliance Laundry Systems SX - page 60

    58 9001900 Section 3 T roub leshootin g © Copyright, Alliance Laundr y S ystems LLC – DO NO T COPY or TRAN S MIT Empty Alarm Analysis (She et 1 of 2) NOTE: Refer to the wiring diagram supplied wi th your machi ne. 1 1 ...

  • Alliance Laundry Systems SX - page 61

    9001900 59 Section 3 T ro ubleshooti ng © Copyright, Alliance Laundr y S ystems LLC – DO NO T COPY or TRAN S MIT Empty Alarm Analysis (She et 2 of 2) CFD1992 S 063787600D ...

  • Alliance Laundry Systems SX - page 62

    60 9001900 Section 3 T roub leshootin g © Copyright, Alliance Laundr y S ystems LLC – DO NO T COPY or TRAN S MIT 15. AUTOMATIC SUPPLY D ISPENSER ANALYSIS Run P rog ram 38 . Run the cycl e and, with the respec tive suppl y on the main disp lay, refer to the foll owing chart for the functi on that sh ould be occ urring: Cycle 38 Suppl y Setup Cycl ...

  • Alliance Laundry Systems SX - page 63

    9001900 61 Section 3 T ro ubleshooti ng © Copyright, Alliance Laundr y S ystems LLC – DO NO T COPY or TRAN S MIT During ea ch step, t est for volt age (220 Vol ts) betwe en each respe ctive sup ply termin al and the common term inal on the supp ly t ermin al b oard . Term in al 14 i s th e com mon termi nal for t he pum ps. The suppl y terminal ...

  • Alliance Laundry Systems SX - page 64

    62 9001900 Section 3 T roub leshootin g © Copyright, Alliance Laundr y S ystems LLC – DO NO T COPY or TRAN S MIT 16. NO KEYPAD BOARD FUNCTIONS Does the display change, indicating that the computer has gone into the cycle that has been selected (e.g., does the “NEXT09” display change to “STEP 01 CYCLE09” “HOT LOW”)? YES Press the star ...

  • Alliance Laundry Systems SX - page 65

    9001900 63 Section 3 T ro ubleshooti ng © Copyright, Alliance Laundr y S ystems LLC – DO NO T COPY or TRAN S MIT 17. EXCESSIVE CYCLE TIME When exper iencing exces sive cycl e time, there a re three mai n causes whic h are as follo ws: a. Fill Ti me: (1) C heck for exc essively long fil l times. Refer to the “F ill Alarm An alysis” fl owchart ...

  • Alliance Laundry Systems SX - page 66

    64 9001900 Section 3 T roub leshootin g © Copyright, Alliance Laundr y S ystems LLC – DO NO T COPY or TRAN S MIT 18. EXCESSIVE VIBRATION AND/OR NOISE DURING SPIN When exper iencing exces sive vibra tion and/or noi se during a s pin cycle, there are t hree main cau ses, whic h ar e as fo llo ws : a. Improper Loadi ng: (1) Alw ays m ake sure tha t ...

  • Alliance Laundry Systems SX - page 67

    9001900 65 T o reduce the risk of electrical shoc k, fire, e xplosion, serious inj ury or death: • Disconnect electrica l power to the washer -extractor bef ore servicing it. • Close the gas shut- off valve to the washer -e xtractor (when applicab le) bef ore servicing it. • Ne ver start the washer-e xtractor with an y guar ds/panels remo ved ...

  • Alliance Laundry Systems SX - page 68

    66 9001900 Section 4 Se rvice Pr ocedures © Copyright, Alliance Laundr y S ystems LLC – DO NO T COPY or TRAN S MIT T o reduce the risk of electrical shoc k, fire, e xplosion, serious inj ury or death: • Disconnect electrica l power to the washer -extractor bef ore servicing it. • Close the gas shut- off valve to the washer -e xtractor (when ...

  • Alliance Laundry Systems SX - page 69

    9001900 67 Section 4 Service Pr ocedures © Copyright, Alliance Laundr y S ystems LLC – DO NO T COPY or TRAN S MIT Cycle 39 — T est Program Step Description Min:sec Step Definitio n Corrective Action 1 Cold Fill to High Le vel 0:30 The machine s hould fill with cold water to high lev el within 30 seconds and, when it does, a b uzzer will sound. ...

  • Alliance Laundry Systems SX - page 70

    68 9001900 Section 4 Se rvice Pr ocedures © Copyright, Alliance Laundr y S ystems LLC – DO NO T COPY or TRAN S MIT 21 Auxiliary 1 0:05 N/A N/A 22 Auxiliary 2 0:05 N/A N/A 23 Auxiliary 3 0:05 N/A N/A 24 150° F Fill to High Le vel 5:00 The water shou ld reach 150°F and the machine should fill to high lev el within 5 minutes and, when it d oes, a ...

  • Alliance Laundry Systems SX - page 71

    9001900 69 Section 4 Service Pr ocedures © Copyright, Alliance Laundr y S ystems LLC – DO NO T COPY or TRAN S MIT T o reduce the risk of electrical shoc k, fire, e xplosion, serious inj ury or death: • Disconnect electrica l power to the washer -extractor bef ore servicing it. • Close the gas shut- off valve to the washer -e xtractor (when a ...

  • Alliance Laundry Systems SX - page 72

    70 9001900 Section 4 Se rvice Pr ocedures © Copyright, Alliance Laundr y S ystems LLC – DO NO T COPY or TRAN S MIT T o reduce the risk of electrical shoc k, fire, e xplosion, serious inj ury or death: • Disconnect electrica l power to the washer -extractor bef ore servicing it. • Close the gas shut- off valve to the washer -e xtractor (when ...

  • Alliance Laundry Systems SX - page 73

    9001900 71 Section 4 Service Pr ocedures © Copyright, Alliance Laundr y S ystems LLC – DO NO T COPY or TRAN S MIT T o reduce the risk of electrical shoc k, fire, e xplosion, serious inj ury or death: • Disconnect electrica l power to the washer -extractor bef ore servicing it. • Close the gas shut- off valve to the washer -e xtractor (when a ...

  • Alliance Laundry Systems SX - page 74

    72 9001900 Section 4 Se rvice Pr ocedures © Copyright, Alliance Laundr y S ystems LLC – DO NO T COPY or TRAN S MIT T o reduce the risk of electrical shoc k, fire, e xplosion, serious inj ury or death: • Disconnect electrica l power to the washer -extractor bef ore servicing it. • Close the gas shut- off valve to the washer -e xtractor (when ...

  • Alliance Laundry Systems SX - page 75

    9001900 73 Section 4 Service Pr ocedures © Copyright, Alliance Laundr y S ystems LLC – DO NO T COPY or TRAN S MIT T o reduce the risk of electrical shoc k, fire, e xplosion, serious inj ury or death: • Disconnect electrica l power to the washer -extractor bef ore servicing it. • Close the gas shut- off valve to the washer -e xtractor (when a ...

  • Alliance Laundry Systems SX - page 76

    74 9001900 Section 4 Se rvice Pr ocedures © Copyright, Alliance Laundr y S ystems LLC – DO NO T COPY or TRAN S MIT T o reduce the risk of electrical shoc k, fire, e xplosion, serious inj ury or death: • Disconnect electrica l power to the washer -extractor bef ore servicing it. • Close the gas shut- off valve to the washer -e xtractor (when ...

  • Alliance Laundry Systems SX - page 77

    9001900 75 Section 4 Service Pr ocedures © Copyright, Alliance Laundr y S ystems LLC – DO NO T COPY or TRAN S MIT T o reduce the risk of electrical shoc k, fire, e xplosion, serious inj ury or death: • Disconnect electrica l power to the washer -extractor bef ore servicing it. • Close the gas shut- off valve to the washer -e xtractor (when a ...

  • Alliance Laundry Systems SX - page 78

    76 9001900 Section 4 Se rvice Pr ocedures © Copyright, Alliance Laundr y S ystems LLC – DO NO T COPY or TRAN S MIT T o reduce the risk of electrical shoc k, fire, e xplosion, serious inj ury or death: • Disconnect electrica l power to the washer -extractor bef ore servicing it. • Close the gas shut- off valve to the washer -e xtractor (when ...

Fabricant Alliance Laundry Systems Catégorie Washer

Les documents que nous recevons du fabricant de l'appareilAlliance Laundry Systems SX peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Alliance Laundry Systems
- manuels d’utilisations SX
- fiches produit Alliance Laundry Systems
- dépliants
- ou étiquettes-énergie Alliance Laundry Systems SX
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Alliance Laundry Systems SX.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Alliance Laundry Systems SX, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Alliance Laundry Systems SX. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Alliance Laundry Systems SX.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Alliance Laundry Systems SX, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Alliance Laundry Systems SX par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Alliance Laundry Systems SX.

Le manuel d’utilisation complet Alliance Laundry Systems, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Alliance Laundry Systems SX - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Alliance Laundry Systems SX, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lAlliance Laundry Systems SX qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Alliance Laundry Systems SX - qui devraient nous aider dans les premières étapes lors de l'utilisation Alliance Laundry Systems SX
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Alliance Laundry Systems SX
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Alliance Laundry Systems SX dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Alliance Laundry Systems SX?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Alliance Laundry Systems SX, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Alliance Laundry Systems SX il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)