Français dropdown-ico

Manuel d’utilisation Hitachi CR 13VA

37 pages 0.98 mb
Télécharger

Aller à la page of 37

Summary
  • Hitachi CR 13VA - page 1

    PO W ER T OOLS TECHNICAL DA T A AND SERVICE MANUAL RECIPROCA TING SA W CR 13V A SPECIFICA TIONS AND P ARTS ARE SUBJECT TO CHANGE FOR IMPROVEMENT LIST No. E930 May 2000 C MODEL CR 13V A ...

  • Hitachi CR 13VA - page 2

    1. PRODUCT NAME ............................................................................................................... . ........... 1 2. MARKETING OBJECTIVE ........................................................................................................ . .... 1 3. APPLIC A TION S .................................................. ...

  • Hitachi CR 13VA - page 3

    - - - 1 - - - 1. PRODUCT NAME Hitachi 130 mm (5") Reciprocating Saw , Model CR 13V A 2. MARKETING OBJECTIVE There is increasing demand for a high-speed and powerful saber saw in overseas markets. The new Model CR 13V A, which features a powerful motor and a swing cutting action, has been developed to meet that market demand. The swing cutting ...

  • Hitachi CR 13VA - page 4

    - - - 2 - - - 4-1. Selling Point Descriptions (1) Fast cutting speed The Model CR 13V A can cut various construction materials fast and efficiently thanks to the high-power motor whose maximum output is over 1000 W (Model CR 10V : 680 V). (2) Saw blade can be mounted and removed without the use of tools (patent pending) Generally , conventional sab ...

  • Hitachi CR 13VA - page 5

    - - - 3 - - - (3) Saw blade can be mounted in either direction, upward or downward The Model CR 13V A is convenient for cutting materials on the floor or near window frames, and also for plunge cutting on plywood panels because the saw blade can be installed upside down. < Cutting on the floor in two-by-four construction > < Plunge cutting ...

  • Hitachi CR 13VA - page 6

    - - - 4 - - - (5) Dust- and water-resistant triple-sealing construction <patent pending> The Model CR 13V A has a triple-sealing construction to protect from the large amount of dust generated when cutting construction materials, autoclaved lightweight concrete, etc. and also from waste water when cutting pipes. Dust-resistant felt ring (with ...

  • Hitachi CR 13VA - page 7

    - - - 5 - - - 4-2. Descriptions of patent pending No. Overseas Japan Descriptions Patent Blade holder of saber saw A detachable mechanism that enables one-hand mounting and removal of saw blades without the use of a wrench or other tools (competitors' products require two-hand operation) A swing cutting mechanism in which the saw blade can be ...

  • Hitachi CR 13VA - page 8

    - - - 6 - - - 5. SPECIFICA TIONS Max. cutting size Steel pipe outer diameter 130 mm (5") Wood thickness (for Europe) 300 mm (for USA) 5" Mild steel plate 19 mm (3/4") Power source AC single phase 50 or 60 Hz T ype of switch Enclosure T ype of motor Full load current Weight Stroke Number of strokes Max. output (reference) Power input ...

  • Hitachi CR 13VA - page 9

    - - - 7 - - - 5-2. Optional Accessories The cutting speed of the Model CR 13V A is substantially higher than that of the current model, however , the conventional HCS blades may be broken in heavy applications such as house demolition, etc. T o cope with this problem, the BI-MET AL blades shown in T able 2 are provided. The BI-MET AL blades are tou ...

  • Hitachi CR 13VA - page 10

    - - - 8 - - - (2) BI-MET AL blades The blade numbers of BI-MET AL blades in T able 2 are engraved in the vicinity of the mounting position of each blade. Select appropriate blades by referring to T able 2 and 3 below . T able 2: BI-MET AL blades Below 3.5 (3) Selection of blades for other materials T able 3 Material to be cut Material quality 2.5 - ...

  • Hitachi CR 13VA - page 11

    - - - 9 - - - 6. COMP ARISONS WITH SIMILAR PRODUCTS 6-1. For USA Market M a k e r HIT A CHI Model CR 13V A 120 11.0 1-1/4 0 - - 2,800 1,070 18.1 6.5 4.1 8.8 126.0 91.0 *T&D Plastic & Rubber (Swing) CR 10V P E S 120 10.0 10.0 10.0 1-1/4 0 - - 2,900 --- --- --- 17.5 6.7 3.7 8.4 121.5 87.2 T&D Rubber 1-1/4 0 - - 3,200 (900) 17.6 6.9 3.6 8. ...

  • Hitachi CR 13VA - page 12

    - - - 10 - - - Swing cutting Orbital cutting Orbital cutting Orbital cutting function is not provided. Orbital cutting function is not provided. Orbital cutting Orbital cutting Orbital cutting function is not provided. 0 10 20 30 40 50 CR 13V A CR 10V A B C D E F Cutting time (sec./cut) Straight cutting Swing or orbital cutting 7. COMP ARISONS IN C ...

  • Hitachi CR 13VA - page 13

    - - - 11 - - - Swing cutting Orbital cutting Orbital cutting function is not provided. Orbital cutting 0 10 20 30 40 50 CR 13V A B C D E F Cutting time (sec./cut) Straight cutting Swing or orbital cutting A Orbital cutting Orbital cutting function is not provided. Orbital cutting function is not provided. A piece of lauan 130 mm (5") in width ...

  • Hitachi CR 13VA - page 14

    - - - 12 - - - 7-3. Cutting Wood with Saw Blade Installed Upside Down HIT ACHI genuine blade No. 121 for cutting wood A piece of lauan lumber 130 mm (5") in width and 43 mm (1.69") in thickness Pressing force about 4 kgf (8.8 lbs.) Swing cutting Orbital cutting function is not provided. 0 10 20 30 40 50 CR 13V A B C D E F Cutting time (se ...

  • Hitachi CR 13VA - page 15

    - - - 13 - - - 7-4. Cutting Operation for Long Blade Life The service life of a saw blade may vary depending on the operating conditions such as the type of cutting action, pressing force, etc. Observing the following instructions can lengthen the service life of a saw blade, for reference. Do not apply undue force to the workpiece. Appropriate pre ...

  • Hitachi CR 13VA - page 16

    - - - 14 - - - 8. PRECAUTIONS IN SALES PROMOTION In the interest of promoting the safest and most efficient use of the Model CR 13V A Reciprocating Saw by all of our customers, it is very important that at the time of sale, the salesperson carefully ensures that the buyer seriously recognizes the importance of the contents of the Handling Instructi ...

  • Hitachi CR 13VA - page 17

    - - - 15 - - - 9. REP AIR GUIDE 9-1. PRECAUTIONS IN DISASSEMBL Y AND REASSEMBL Y Please follow the precautions below for disassembly and reassembly procedures. The circled numbers in the following figures and the [Bold] numbers in the descriptions below correspond to the item numbers in the Parts List. Prior to attempting disassembly or replacement ...

  • Hitachi CR 13VA - page 18

    - - - 16 - - - Loosen the Nylock Bolt (W/Flange) M6 x 35 [47] which secures the fan of the armature ass'y (approximately two turns). Remove the four Machine Screws (W/W ashers) M5 x 60 [42] and then pull out the Gear Cover [31] from the main body . Remove the Nylock Bolt (W/Flange) M6 x 35 [47] , then Second Shaft (A) [64] section and the Sub ...

  • Hitachi CR 13VA - page 19

    - - - 17 - - - (3) Disassembly of the blade mounting section (Fig. 5) Remove the Retaining Ring (E-T ype) for D14 Shaft [2] from Plunger (A) Set [32] with a flatblade screwdriver . At this time, be careful that Spring (A) [19] is pushing against the retaining ring. Next, slide the Guide Washer [17] backward and remove the two Steel Balls D4.76 [15] ...

  • Hitachi CR 13VA - page 20

    - - - 18 - - - (5) Disassembly of the Second Shaft (A) [64] section (Fig. 7) Remove the Retaining Ring for D17 Shaft [60] from Second Shaft (A) [64] . While holding the side surface of the Recipro Plate [61] , push the end surface of Second Shaft (A) [64] (parallel with the side surface of the Recipro Plate [61] ) with a hand press and remove the R ...

  • Hitachi CR 13VA - page 21

    - - - 19 - - - (8) Disassembly of Handles (A) [74] and (B) [80] section (Fig. 10) Remove the six T apping Screws (W/Flange) D4 x 25 [43] . Remove the Grip Cover [81] by pulling it backward and remove Handle (A) [74] . Then, the Switch T rigger [76] can be removed. Fig. 10 Fig. 1 1 Fig. 12 (9) Disassembly of Handle (B) [80] and the Switch [75] secti ...

  • Hitachi CR 13VA - page 22

    - - - 20 - - - Fig. 13-a 2. Reassembly Reassembly can be accomplished by following the disassembly procedures in reverse. However , special attention should be given to following items. (1) Press-fitting the Recipro Plate [61] ass'y into Second Shaft (A) [64] (Fig.13) T ool required: Special repair tool J-315 Mount the two Ball Bearings 6003VV ...

  • Hitachi CR 13VA - page 23

    - - - 21 - - - (3) Reassembly of the blade mounting section (Figs. 15, 16 and 17) Apply Doubrex 251 grease to the inner circumference of Holder Sleeve (B) [14] and the cam groove of Plunger (A) Set [32] . Mount W asher (E) [1] , Thrust Bearing [21] , Washer (D) [20] , Spring (A) [19] , Dust W asher [18] , Guide W asher [17] , Holder Sleeve (C) [16] ...

  • Hitachi CR 13VA - page 24

    - - - 22 - - - (4) Press-fitting plunger (A) into the plunger sleeve (Figs. 18 and 19) T ool required: Special repair tool J-317 Apply Nippeco SEP-3A grease to the sliding portion of plunger (A) and insert it into the Guide Sleeve Ass'y [9] . Insert the Pin D6 [54] into plunger (A). Mount it to the special repair tool J-317 and press-fit it in ...

  • Hitachi CR 13VA - page 25

    - - - 23 - - - * Be careful not to damage W asher (F) [3] . (Fig. 21) W asher (F) has an oval shape to fit the inside of the Gear Cover [31] . Therefore, perform disassembly and reassembly so that washer (F) is properly aligned with the shape of the gear cover . *Be careful of the direction of the Cord Clip [78] . (Fig. 22) *Precaution when mountin ...

  • Hitachi CR 13VA - page 26

    - - - 24 - - - 9-2. Lubrication (1) Nippeco SEP-3A grease Lip portion of the V -Ring [7] Inner circumference of the Swing Roller [53] Sphere portion of the Recipro Plate [61] Both sides of the Thrust Bearing [21] Inner circumferene of the Guide Sleeve Ass'y [9] and Metal (A) [8] Apply 45 g of Nippeco SEP-3A to the Gear Cover [31] . (2) Doubrex ...

  • Hitachi CR 13VA - page 27

    - - - 25 - - - For stator ass'y , or for stator ass'y and noise suppressor For triac ass'y , or for triac ass'y and noise suppressor For cord For stator ass'y Noise suppressor Switch body T ube (D) Cord T erminal T riac ass'y Dial resistor T ube (D) For cord Fig. 24 Armature Stator M1 M2 1 2 Black Red R 2 Black Red Blu ...

  • Hitachi CR 13VA - page 28

    - - - 26 - - - 10. CONFIRMA TION AFTER REASSEMBL Y 10-1. Lead Wire Precautions When connecting lead wires, be very careful not to remove the insulation covering of each lead wire more than needed. Also, ensure that the lead wires are not pinched between the mating surfaces of the handle. 10-2. Insulation T ests On completion of disassembly and repa ...

  • Hitachi CR 13VA - page 29

    - - - 27 - - - 1 1. ST ANDARD REP AIR TIME (UNIT) SCHEDULES MODEL 10 20 30 40 60 50 Fixed V ariable CR 13V A Work Flow Handle (A),(B) Switch Cord Cord Armor Switch Trigger Front Cover (A) Front Cover (B) Inner Cover (A) Armature Ass'y Ball Bearing (6001VV) Ball Bearing (608VV) Change Shaft O-Ring Ball Bearing (6003DD) Sub Shaft Recipro Plate B ...

  • Hitachi CR 13VA - page 30

    - - - 28 - - - SABER SA W Model CR 13V A 1999 • 12 • 20 ( E1 ) LIST NO. 0786 ELECTRIC T OOL P AR TS LIST ...

  • Hitachi CR 13VA - page 31

    - - - 29 - - - PARTS CR 13VA : ALTERNATIVE PARTS ITEM NO. CODE NO. DESCRIPTION NO. USED REMARKS 1 318-484 WASHER (E) 1 2 318-453 RETAINING RING (E-TYPE) FOR D14 SHAFT 1 3 318-457 WASHER (F) 1 4 878-609 O-RING (S-24) 1 5 318-458 FELT WASHER 1 6 318-460 SEAL SLEEVE 1 7 318-459 V-RING 1 8 318-463 METAL (A) 1 9 318-462 GUIDE SLEEVE ASS'Y 1 INCLUD. ...

  • Hitachi CR 13VA - page 32

    - - - 30 - - - CR 13VA ITEM NO. CODE NO. DESCRIPTION NO. USED REMARKS 52 318-488 SWING RAIL 2 53 318-492 SWING ROLLER 2 54 318-491 PIN D6 1 55 HITACHI LABEL 1 56 600-3DD BALL BEARING 6003DDCMPS2S 1 57 318-475 SUB SHAFT 1 58 318-476 BEARING COVER (B) 1 59 949-216 MACHINE SCREW M4X10 (10 PCS.) 2 60 967-261 RETAINING RING FOR D17 SHAFT 1 61 318-466 RE ...

  • Hitachi CR 13VA - page 33

    - - - 31 - - - Printed in Japan (991220 N) : ALTERNATIVE PARTS * PARTS OPTIONAL ACCESSORIES CR 13VA ITEM No. CODE NO. DESCRIPTION NO. USED REMARKS * 85 500-434Z CORD 1 (CORD ARMOR D8.8) FOR USA * 85 500-455Z CORD 1 (CORD ARMOR D8.8) FOR CHNOR ITEM No. CODE NO. DESCRIPTION NO. USED REMARKS 501 318-613 SABER SAW BLADES NO.103 150L P.14 (5 PCS.) 1 502 ...

  • Hitachi CR 13VA - page 34

    - - - 32 - - - SABER SA W Model CR 13V A [For the U.S.A. and Canada only] 2000 • 2 • 15 ( E1 ) LIST NO. 0786 ELECTRIC T OOL P AR TS LIST ...

  • Hitachi CR 13VA - page 35

    - - - 33 - - - PARTS CR 13VA : ALTERNATIVE PARTS ITEM NO. CODE NO. DESCRIPTION NO. USED REMARKS 1 318-484 WASHER (E) 1 2 318-453 RETAINING RING (E-TYPE) FOR D14 SHAFT 1 3 318-457 WASHER (F) 1 4 878-609 O-RING (S-24) 1 5 318-458 FELT WASHER 1 6 318-460 SEAL SLEEVE 1 7 318-459 V-RING 1 8 318-463 METAL (A) 1 9 318-462 GUIDE SLEEVE ASS'Y 1 INCLUD. ...

  • Hitachi CR 13VA - page 36

    - - - 34 - - - CR 13VA ITEM NO. CODE NO. DESCRIPTION NO. USED REMARKS 52 318-488 SWING RAIL 2 53 318-492 SWING ROLLER 2 54 318-491 PIN D6 1 55 HITACHI LABEL 1 56 600-3DD BALL BEARING 6003DDCMPS2S 1 57 318-475 SUB SHAFT 1 58 318-476 BEARING COVER (B) 1 59 949-216 MACHINE SCREW M4X10 (10 PCS.) 2 60 967-261 RETAINING RING FOR D17 SHAFT 1 61 318-466 RE ...

  • Hitachi CR 13VA - page 37

    - - - 35 - - - Printed in Japan (000215 N) : ALTERNATIVE PARTS * STANDARD ACCESSORIES CR 13VA ITEM No. CODE NO. DESCRIPTION NO. USED REMARKS 502 312831 CASE 1 551 8" BI-M ALLPURP Progressive Recip. Blade 1PC 1 See Item No.677 651 725300 6" HCS WOOD 6TPI Recip. Blade 5PCS 1 652 725301 9" HCS WOOD 5TPI Recip. Blade 5PCS 1 653 725302 12 ...

Fabricant Hitachi Catégorie Range

Les documents que nous recevons du fabricant de l'appareilHitachi CR 13VA peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Hitachi
- manuels d’utilisations CR 13VA
- fiches produit Hitachi
- dépliants
- ou étiquettes-énergie Hitachi CR 13VA
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Hitachi CR 13VA.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Hitachi CR 13VA, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Hitachi CR 13VA. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Hitachi CR 13VA.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Hitachi CR 13VA, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Hitachi CR 13VA par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Hitachi CR 13VA.

Le manuel d’utilisation complet Hitachi, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Hitachi CR 13VA - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Hitachi CR 13VA, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lHitachi CR 13VA qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Hitachi CR 13VA - qui devraient nous aider dans les premières étapes lors de l'utilisation Hitachi CR 13VA
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Hitachi CR 13VA
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Hitachi CR 13VA dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Hitachi CR 13VA?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Hitachi CR 13VA, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Hitachi CR 13VA il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)