Français dropdown-ico

Manuel d’utilisation Mitsumi electronic MR-J3- A

670 pages 12.71 mb
Télécharger

Aller à la page of 670

Summary
  • Mitsumi electronic MR-J3- A - page 1

    SH (NA) 030038-L (1406) MEE Printed in Japan Specifications are subject to change without notice. This Instruction Manual uses recycled paper. MODEL MODEL CODE J3 Series MR-J3- A Servo Amplifier Instruction Manual L General-Purpose AC Servo MODEL MR-J3- A SERVO AMPLIFIER INSTRUCTION MANUAL General-Purpose Interface J3 Series L 1CW203 MR-J3-A INSTRU ...

  • Mitsumi electronic MR-J3- A - page 2

    A - 1 Safety Instructions (Always read these instructi ons before using the equip ment.) Do not attempt to install, o perate, ma in tain or inspect the converter unit, servo amplifier (drive unit) and servo motor until you have read through this Instruction Manual, Installation guide, Servo motor Instru ction Manual (Vol.2) and appended documents c ...

  • Mitsumi electronic MR-J3- A - page 3

    A - 2 1. To prevent electric shock, note the following WARNING Before wiring or inspection, turn o ff the power and wait for 15 minutes or more (20 minutes or for drive unit 30kW or more) until the charge lamp turns of f. Then, confirm that the voltage between P( ) and N( ) (L and L for drive unit 30kW or more) is safe with a voltage tester and oth ...

  • Mitsumi electronic MR-J3- A - page 4

    A - 3 3. To prevent injury, note the follow CAUTION Only the voltage specified in the Instruction Manual should be applie d to each terminal, O therwise, a burst, damage, etc. ma y occur. Connect the terminals correctly to preve nt a burst, damage, etc. Ensure that polarit y ( , ) is correct. Otherwise, a burst, damage, e tc. may occur. Take safety ...

  • Mitsumi electronic MR-J3- A - page 5

    A - 4 CAUTION When you keep or use it, please fulfill the following environmental conditions. Item Environmental conditions Converter unit servo amplifier (drive unit) Servo motor Ambient temperature In operation [ ] 0 to 55 (non-fre ezing) 0 to 40 (non-fre ezing) [ ] 32 to 131 (non-freezing) 32 to 104 (non-freezing) In storage [ ] 20 to 65 (non-fr ...

  • Mitsumi electronic MR-J3- A - page 6

    A - 5 CAUTION The surge absorbing diode installed to the DC relay for control outpu t should be fitted in the specified direction. Otherwise, the emergency sto p and other pr otective circuits may not op erate. DOCOM Contro l outp ut signal DICOM 24VDC Servo amplifier (drive unit) RA For sink output interface DOCOM Contro l outp ut signal DICOM 24V ...

  • Mitsumi electronic MR-J3- A - page 7

    A - 6 (5) Corrective actions CAUTION When it is assumed that a h azardous condition may ta ke place at the occur due to a power fa ilure or a product fault, use a servo motor with an electromagneti c brake or an external brake mechanism for the purpose of prevention. Configure an electromagnetic brake circuit so that it is activated also by an exte ...

  • Mitsumi electronic MR-J3- A - page 8

    A - 7 DISPOSAL OF WASTE Please dispose a converter unit, servo amplifier (drive unit), batter y (primary battery) and other options according to your local laws and regulations. EEP-ROM life The number of write times to the EEP-R OM, which stor es parameter settings, etc., is limited to 100,000. If the total number of the following oper ations exce ...

  • Mitsumi electronic MR-J3- A - page 9

    A - 8 MEMO ...

  • Mitsumi electronic MR-J3- A - page 10

    1 CONTENTS 1. FUNCTIONS AND CONFIG URATION 1 - 1 to 1 -30 1.1 Summa ry ................................................................................................................... ............................... 1 - 1 1.2 Function bl ock diagram ................................................................................................. ...

  • Mitsumi electronic MR-J3- A - page 11

    2 3.10 Connection of servo amp lifier and s e rvo motor ............................................................................ ....... 3 -62 3.10.1 Connection instruct ions ................................................................................................ .................. 3 -62 3.10.2 Power supply c able wiring diagram s ..... ...

  • Mitsumi electronic MR-J3- A - page 12

    3 5.1.9 Auto tuning ............................................................................................................. .......................... 5 -12 5.1.10 In-pos ition range ...................................................................................................... ...................... 5 -13 5.1.11 Tor que lim it ....... ...

  • Mitsumi electronic MR-J3- A - page 13

    4 7.2.2 Auto tun i ng mode basi s .................................................................................................. .................. 7 - 4 7.2.3 Adjustment procedur e by auto tunin g ..................................................................................... .......... 7 - 5 7.2.4 Response level settin g in auto tuni n ...

  • Mitsumi electronic MR-J3- A - page 14

    5 12.2 Regenerativ e opti ons ..................................................................................................... ...................... 12-27 12.3 FR-BU2-(H) brake unit .................................................................................................... ..................... 12-40 12.3.1 Sele cti on .............. ...

  • Mitsumi electronic MR-J3- A - page 15

    6 13.5.8 Test oper ation mod e .................................................................................................... ................. 13-27 13.5.9 Output signal pin ON/OFF outpu t signal (DO) forced output ....................................................... 13-30 13.5.10 Alar m his tory .......................................... ...

  • Mitsumi electronic MR-J3- A - page 16

    7 15.1.7 Removal and reinstallation of the terminal b lock cover ............................................................... 1 5-13 15.1.8 Servo system with auxil iary equipment .................................................................................. ...... 15-19 15.2 Insta llation ..................................................... ...

  • Mitsumi electronic MR-J3- A - page 17

    8 16.2 Specific ations ........................................................................................................... ............................. 16- 3 16.3 Outline dimens ion dra w ings ............................................................................................... .................. 16- 3 16.4 Connection with servo ...

  • Mitsumi electronic MR-J3- A - page 18

    1 - 1 1. FUNCTIONS AND CONFIGURATION 1. FUNCTIONS AND CONFIGURATION 1.1 Summary The Mitsubishi MELSERVO-J3 series general-purpose AC servo is b ased on the MELSERVO-J2-Super series and has further higher performance and higher functions. It has position control, speed control and torque contro l modes. Further, it can perform operation with the con ...

  • Mitsumi electronic MR-J3- A - page 19

    1 - 2 1. FUNCTIONS AND CONFIGURATIO N 1.2 Function block diagram The function block diagram of this servo is shown below. (1) MR-J3-350A or less MR-J3-200A4 or less CD L 11 CN5 CN3 CN6 I/F USB RS-422 D/A A/D USB RS-42 2 CN4 MR-J3BAT CN1 P 1 P 2 P( ) N( ) B NFB (Note 2 ) Power supply MC RA 24VDC B1 B2 L 1 L 2 L 3 L 21 Servo amplifier U V W U V W Dio ...

  • Mitsumi electronic MR-J3- A - page 20

    1 - 3 1. FUNCTIONS AND CONFIGURATIO N (2) MR-J3-350A4 MR-J3-500A(4) MR-J3-700A(4) CN2 C L 11 CN5 CN3 CN6 I/F USB RS-422 D/A A/D USB RS-422 CN4 MR-J3BAT CN1 P 1 P 2 PN B NFB (Note) Power supply MC RA 24VDC B1 B2 L 1 L 2 L 3 L 21 Servo amplifier U V W U V W Diode stack Regene rative option Power factor improvi ng DC reactor CHARGE lamp Regene- rative ...

  • Mitsumi electronic MR-J3- A - page 21

    1 - 4 1. FUNCTIONS AND CONFIGURATIO N (3) MR-J3-11KA(4) to 22KA(4) C L 11 CN5 CN3 CN6 I/F USB RS-422 D/A A/D USB RS-422 CN4 MR-J3BAT CN1 P 1 PN B NFB (Note 1) Power supply MC RA 24VDC B1 B2 L 1 L 2 L 3 L 21 Servo amplifier U V W U V W Diode stack Regenerative optio n Power factor improving DC reactor CHARGE lamp Reg ene- rative TR Current detector ...

  • Mitsumi electronic MR-J3- A - page 22

    1 - 5 1. FUNCTIONS AND CONFIGURATIO N 1.3 Servo amplifier standard specifications (1) 200V class, 100V class Serv o ampl ifier MR-J3- Item 10 A 20 A 4 0A 60 A 70 A 100A 200A 350A 500A 700A 11KA 15KA 22KA 10A1 20A1 40A1 Output Rated voltage 3-phase 170VAC Rated curre nt [A ] 1.1 1.5 2.8 3.2 5.8 6.0 11.0 17.0 28.0 37.0 68. 0 87.0 126.0 1.1 1.5 2.8 Ma ...

  • Mitsumi electronic MR-J3- A - page 23

    1 - 6 1. FUNCTIONS AND CONFIGURATIO N Note 1. 0.3A is the value applicable when all I/O signals are used. The current capaci ty can be decreased by reducing the numbe r of I/O points. 2. When closely mounting the servo amplifier of 3.5kW or le ss, operate them at the ambient temperatures of 0 to 45 o r at 75% or smaller effective load ratio. 3. Whe ...

  • Mitsumi electronic MR-J3- A - page 24

    1 - 7 1. FUNCTIONS AND CONFIGURATIO N 1.4 Function list The following table lists the functions of this servo. Fo r details of the functions, refer to the reference fie ld. Function Description (Note) Control mode Reference Position control mode This servo is used as position control servo. P Section 3.2.1 Section 3.6.1 Section 4.2 Speed control mo ...

  • Mitsumi electronic MR-J3- A - page 25

    1 - 8 1. FUNCTIONS AND CONFIGURATIO N Function Description (Note) Control mode Reference Position smoothing Speed can be increased smoothly in response to input pulse. P Parameter No.PB03 S-pattern acceleration/ deceleration time constant Speed can be increased and decreased smoothly. S, T Parameter No.PC03 Regenerative option Used when the built-i ...

  • Mitsumi electronic MR-J3- A - page 26

    1 - 9 1. FUNCTIONS AND CONFIGURATIO N 1.5 Model code definition (1) Rating plate Model Capacity Applicable power supply Serial number MITSUBISHI MADE IN JAPAN MODEL MR-J3-10A MITSUBISHI ELECTRI C CORPORATION AC SERVO PASSED POWER : INPUT : OUTPUT : SERIAL : 100W 1.3A 1PH 230V 50/60H z 170V 0-36 0Hz 1.1A A34230 001 0.9A 3PH+1 PH200-230V 50Hz 3PH+1PH ...

  • Mitsumi electronic MR-J3- A - page 27

    1 - 10 1. FUNCTIONS AND CONFIGURATIO N 1.6 Combination with servo motor The following table lis ts combinations of servo amplif iers and servo motors. The s ame combinations apply to the models with an electromagnetic br ake and the models with a reduction gear. Servo amplifier Servo motors HF-MP HF-KP HF-SP HC-RP HC-UP HC-LP 1000r/min 2000r/min MR ...

  • Mitsumi electronic MR-J3- A - page 28

    1 - 11 1. FUNCTIONS AND CONFIGURATIO N Servo amplifiers supporting the 400 maximum torque setting Servo motor Servo amplifiers supporting the 400 maximum torque setting Servo motor HF-JP HF-JP MR-J3-100A-U100 53 MR-J3-100A4-U110 534 MR-J3-200A-U101 73 MR-J3-200A4-U111 734 MR-J3-200A-U102 103 MR-J3-200A4-U112 1034 MR-J3-350A-U103 153 MR-J3-350A4-U11 ...

  • Mitsumi electronic MR-J3- A - page 29

    1 - 12 1. FUNCTIONS AND CONFIGURATIO N 1.7 Structure 1.7.1 Parts identification (1) MR-J3-100A or less MODE UP DOWN SET Main circuit pow er supply connector (CNP1) Connec t the input power supply. USB communi cation connector (CN5) Connect the personal computer. Analog monitor connector (CN6) Outputs the analog monitor. RS-422 communication connect ...

  • Mitsumi electronic MR-J3- A - page 30

    1 - 13 1. FUNCTIONS AND CONFIGURATIO N (2) MR-J3-60A4 MR-J3-100A4 MODE UP DOWN SET Fixed part (3 places) Name/Applic ation Main circ uit power supp ly connector ( CNP1) Connect t he input power supply. USB communi cation connector (CN5) Connect the person al computer. Analog moni tor connect or (CN6) Outputs the a nalog monit or. RS-422 communicati ...

  • Mitsumi electronic MR-J3- A - page 31

    1 - 14 1. FUNCTIONS AND CONFIGURATIO N (3) MR-J3-200A(4) MODE UP DOWN SET Cooling f an Fixed pa rt (3 p laces ) Name/Application Main circuit power supply connector (CNP1) Conne ct the input powe r supp ly. USB communication connector (CN5) Connect the personal computer. Analog monitor connector (CN6) Outputs the analog monitor. RS-422 communicatio ...

  • Mitsumi electronic MR-J3- A - page 32

    1 - 15 1. FUNCTIONS AND CONFIGURATIO N (4) MR-J3-350A MODE UP DOW N SET Rating pl ate Section 1.5 Operati on section Used to perform s tatus display, diag nostic, alarm and parameter set ting operatio ns. Cooling fa n Display The 5-digi t, seven-s egment LED shows the servo status and alarm number. Name/Appl ication Deta iled explana tion Used to c ...

  • Mitsumi electronic MR-J3- A - page 33

    1 - 16 1. FUNCTIONS AND CONFIGURATIO N (5) MR-J3-350A4 MR-J3-500A(4) POINT The servo amplifier is shown without the front cover. For removal of the front cover, refer to section 1.7. 2. Section 3.2 Section 3.4 MODE UP DOWN SET Fixed part (4 place) Cooling fa n Rating plate Section 1.5 Display The 5- digit, seve n-segment LED shows the servo status ...

  • Mitsumi electronic MR-J3- A - page 34

    1 - 17 1. FUNCTIONS AND CONFIGURATIO N (6) MR-J3-700A(4) POINT The servo amplifier is shown without the front cover. For removal of the front cover, refer to section 1.7. 2. Rating plate Operation section Used to perform status display, diagnost ic, alarm and parameter setting operations. Display The 5-digit, seven-segment LED shows the servo statu ...

  • Mitsumi electronic MR-J3- A - page 35

    1 - 18 1. FUNCTIONS AND CONFIGURATIO N (7) MR-J3-11KA(4) to MR-J3-22KA(4) POINT The servo amplifier is shown without the front cover. For removal of the front cover, refer to section 1.7. 2. Section 3.1 Section 3.3 Main circuit, cont rol circuit and pro tective earth (PE ) terminal bloc k Used to connect t he input power supply, se rvo motor, regen ...

  • Mitsumi electronic MR-J3- A - page 36

    1 - 19 1. FUNCTIONS AND CONFIGURATIO N 1.7.2 Removal and reinstallation of the front cover WARNING Before removing or installing the front cover, turn off the power and wait for 15 minutes or longer until the charge lamp turns off. Then, confirm that the voltage between P( ) and N( ) is safe with a voltage tester and others. Otherwise, an electric ...

  • Mitsumi electronic MR-J3- A - page 37

    1 - 20 1. FUNCTIONS AND CONFIGURATIO N Reinstallation of the front co ver Fron t cove r setting tab A) A) 1) Insert the front co ver setting tabs into th e sockets of servo amplifier (2 places). 2) Pull up the cover, suppor ting at point A) . Setting tab 3) Push the setting tabs until they click. ...

  • Mitsumi electronic MR-J3- A - page 38

    1 - 21 1. FUNCTIONS AND CONFIGURATIO N (2) For MR-J3-11KA(4) to MR-J3-22KA(4) Removal of the fron t cover C) B) A) 1) Press the removing knob on the lower side of the front cover ( A) and B) ) and release the installation hook. 2) Press the removing knob of C) and release the installation hook. 3) Pull it to re move the front co ver. Reinstallation ...

  • Mitsumi electronic MR-J3- A - page 39

    1 - 22 1. FUNCTIONS AND CONFIGURATIO N 1.8 Configuration includ ing auxiliary equipment POINT Equipment other than the servo amp lifier and servo motor are optional or recomme nded prod ucts. (1) MR-J3-100A or less (a) For 3-phase or 1-phase 200 to 230VAC (Note 3) Power supply Line noise filter (FR-BSF01) R S T Magnet ic contactor (MC) No-fuse brea ...

  • Mitsumi electronic MR-J3- A - page 40

    1 - 23 1. FUNCTIONS AND CONFIGURATIO N (b) For 1-phase 100 to 120VAC (Note 3) Power supply Line noise filter (FR-BSF01) Magnet ic contactor (MC) No-fu se br eaker (NFB) or fuse CN5 CN3 Regenerative option PC L 11 L 21 Analog monitor CN1 CN2 CN4 Junction te rminal block CN6 U V W Servo amplifier Servo mot or (Note 1) Battery MR-J3BAT L 1 L 2 MR Conf ...

  • Mitsumi electronic MR-J3- A - page 41

    1 - 24 1. FUNCTIONS AND CONFIGURATIO N (2) MR-J3-60A4 MR-J3-100A4 P Line noise filter (FR-BSF01) Magnetic contactor (MC) No-fu se br eaker (NFB) or fuse Regenerative option Analog monitor Juncti on ter minal block Servo amplifier Servo motor (Not e 1) Battery MR-J3BAT (Note 2 ) Power factor improvi ng DC reactor (FR-BEL-H) (Note 3) Power supply (No ...

  • Mitsumi electronic MR-J3- A - page 42

    1 - 25 1. FUNCTIONS AND CONFIGURATIO N (3) MR-J3-200A(4) Line noise filter (FR-BSF0 1) Magnet ic contactor (MC) No-fuse breaker (NFB) or fuse Regenerative option Analog monitor Junction terminal block Servo amplifier Servo motor (Note 1) Battery MR-J3BAT (Note 3) Power supply (Note 2 ) R S T P 1 P 2 UV W CN5 CN3 CN2 CN4 CN1 CN6 MR Con figurator Per ...

  • Mitsumi electronic MR-J3- A - page 43

    1 - 26 1. FUNCTIONS AND CONFIGURATIO N (4) MR-J3-350A Line noi se filter (FR-BLF) (Note 3) Power suppl y Magneti c contactor (MC) No-fuse b reaker (NFB) or fuse Regenerative option P C L 21 (Note 2) Power factor improving DC reactor (FR-BEL) P 1 P 2 U V W Servo amplifier CN5 CN3 Analog monitor CN2 CN4 CN1 Junction terminal block CN6 MR Conf igurato ...

  • Mitsumi electronic MR-J3- A - page 44

    1 - 27 1. FUNCTIONS AND CONFIGURATIO N (5) MR-J3-350A4 MR-J3-500A(4) (Note 3) Power supply Line noise filte r (FR-BLF) R S T L 21 P 1 P 2 CN5 CN3 CN2 CN4 CN1 CN6 L 11 UV W C P L 1 L 2 L 3 Magnetic contactor (MC) No-fuse breaker (NFB) or fuse (Note 2) Servo amplifier Regenerative option (Note 2) Power factor improving DC reacto r (FR-BEL-(H)) (Note ...

  • Mitsumi electronic MR-J3- A - page 45

    1 - 28 1. FUNCTIONS AND CONFIGURATIO N (6) MR-J3-700A(4) R S T L 21 P 2 P 1 CN5 CN3 CN2 CN4 CN1 CN6 L 11 UV W C P L 1 L 2 L 3 Line noise filter (FR-BLF) (Note 3) Power supply Magnetic conta ctor (MC) No-fuse breaker (NFB) or fuse (Note 2) (Note 2) Power fa ctor improving DC reactor (FR-BEL-(H)) Servo amplifier Regenerative option (Note 1) Battery M ...

  • Mitsumi electronic MR-J3- A - page 46

    1 - 29 1. FUNCTIONS AND CONFIGURATIO N (7) MR-J3-11KA(4) to MR-J3-22KA(4) (Note 3) Power supply R S T L 21 Servo am plifier (Note 2) L 11 U V W C P L 1 L 2 L 3 CN4 CN2 P 1 P CN5 CN3 CN1 CN6 Analog monitor Personal computer MR Con figurator No-fuse breaker (NFB) or fu se Magnet ic contactor (MC) Line noise filter (FR-BLF) Power factor improvi ng DC ...

  • Mitsumi electronic MR-J3- A - page 47

    1 - 30 1. FUNCTIONS AND CONFIGURATIO N MEMO ...

  • Mitsumi electronic MR-J3- A - page 48

    2 - 1 2. INSTALLATION 2. INSTALLATION WARNING To prevent electric shock, ground each equipment securely. CAUTION Stacking in excess of the limited number of product packages is not allowed. Install the equipment to incombustibles. Installing them directly or clo se to combustibles will led to a fire. Install the equipment in a load-bearing plac e i ...

  • Mitsumi electronic MR-J3- A - page 49

    2 - 2 2. INSTALLATION 2.1 Installation direction and clea rances CAUTION The equipment must be ins talled in the s pecified direction. Otherwise, a fault may occur. Leave specified clearances between the serv o amplifie r and control box inside walls or other equipment. (1) 7kW or less (a) Installation of one servo amplifier Control box Top Bottom ...

  • Mitsumi electronic MR-J3- A - page 50

    2 - 3 2. INSTALLATION (b) Installation of two or more servo amplifiers POINT Close mounting is availabl e for the serv o amplifier of under 3.5 kW for 200V class and 400W for 100V class. Leave a large clearance between the top of the servo am plifier and the internal surf ace of the control box, and install a cooling fan to prevent the in ternal te ...

  • Mitsumi electronic MR-J3- A - page 51

    2 - 4 2. INSTALLATION (b) Installation of two or more servo amplifiers Leave a large clearance between the top of the servo am plifier and the internal surf ace of the control box, and install a cooling fan to prevent the in ternal temperature of the cont rol box from exceeding the environmental conditions. 100mm or more 30mm or mor e 120mm or more ...

  • Mitsumi electronic MR-J3- A - page 52

    2 - 5 2. INSTALLATION 2.3 Cable stress (1) The way of clamping the cable mus t be fully examined so that flexing stress and cable's own weight s tress are not applied to the cable connection. (2) For use in any application where the servo motor move s, fix the cables (encoder, power sup ply, brake) with having some slack from the connector co ...

  • Mitsumi electronic MR-J3- A - page 53

    2 - 6 2. INSTALLATION 2.5 Parts having service lives The following parts must be changed periodically as listed below. If any part is found faulty, it must be changed immediately even when it has not yet rea ched the end of its life, which depends on the operating method and environmental conditions. For parts replac ement , please contact your loc ...

  • Mitsumi electronic MR-J3- A - page 54

    3 - 1 3. SIGNALS AND WIRING 3. SIGNALS AND WIRING WARNING Any person who is involved in wiring s hould be fully competent to do the work. Before wiring, turn off the p ower and wait for 15 minutes or longer until the charge lamp turns off. Then, confirm tha t the voltage between P( ) and N( ) is safe with a voltage tester and others . Otherwise, an ...

  • Mitsumi electronic MR-J3- A - page 55

    3 - 2 3. SIGNALS AND WI RING 3.1 Input power supply circuit CAUTION Always connect a magnetic contactor be tween the main circuit power and L 1 , L 2 , and L 3 of the servo amplifier, and configure the wiring to be ab le to shut down the power supply on the side of the servo amplifier’s power supply. If a magnetic contactor is not connected, cont ...

  • Mitsumi electronic MR-J3- A - page 56

    3 - 3 3. SIGNALS AND WI RING Note 1. Always connect P 1 and P 2 . (Factory-wired.) When using the po wer factor improving DC reactor, refer to section 12.13. Use only one of power factor improving DC r eactor or power factor improving AC reactor. 2. Always connect P( ) and D. (Factory-wired.) When using the reg enerative option, refer to section 12 ...

  • Mitsumi electronic MR-J3- A - page 57

    3 - 4 3. SIGNALS AND WI RING (3) MR-J3-10A1 to MR-J3-40A1 P N (Note 4) Troubl e SON EMG L 1 Blank L 2 1-phase 100 to 120VAC ALM P 1 P 2 DICOM DOCOM L 11 L 21 D C U V W (Note 1) (Note 2) CNP1 CNP3 PE CNP2 U V W M Motor Encoder CN2 (Not e 3) Encoder cab le (Note 5) DOCOM CN1 CN1 24 VDC Trouble (Note 4) MC NFB RA Servo motor Servo am plif ier Emergenc ...

  • Mitsumi electronic MR-J3- A - page 58

    3 - 5 3. SIGNALS AND WI RING (4) MR-J3-60A4 to MR-J3-200A4 P N (Note 4) SON EMG L 1 L 2 L 3 3-phase 380 to 480VAC ALM P 1 P 2 DICOM DOCOM L 11 L 21 D C U V W (Note 1) (Note 2) CNP1 CNP3 PE CNP2 U V W M Motor Encoder CN2 (Not e 3) Encoder cab le (Note 5) DOCOM CN1 CN1 24 VDC Trouble (Note 4) MC NFB RA Servo motor Servo amp lif ier Emergency stop (No ...

  • Mitsumi electronic MR-J3- A - page 59

    3 - 6 3. SIGNALS AND WI RING (5) MR-J3-500A MR-J3-700A TE1 TE2 TE3 Built-in regene rati ve resistor Cooling f an BU BV NFB (Note 6 ) Power supply of cooli ng fan P N (Note 4 ) SON EMG L 1 L 2 L 3 3-phase 200 to 230VAC ALM P 1 P 2 DICOM DOCOM L 11 L 21 C U V W (Note 1) (Note 2) PE U V W M Motor Encoder CN2 (Not e 3) Encoder cab le (Note 5) DOCOM CN1 ...

  • Mitsumi electronic MR-J3- A - page 60

    3 - 7 3. SIGNALS AND WI RING (6) MR-J3-350A4 to MR-J3-700A4 TE1 TE2 TE3 Built-in regene rati ve resistor Cooling f an BU BV NFB (Note 7 ) Power supply of cooli ng fan P N (Note 4 ) SON EMG L 1 L 2 L 3 3-phase 380 to 480VAC ALM P 1 P 2 DICOM DOCOM L 11 L 21 C U V W (Note 1) (Note 2) PE U V W M Motor Encoder CN2 (Not e 3) Encoder cab le (Note 5) DOCO ...

  • Mitsumi electronic MR-J3- A - page 61

    3 - 8 3. SIGNALS AND WI RING (7) MR-J3-11KA to MR-J3-22KA External dynamic brake (option ) (Note 10) NFB L 1 L 2 L 3 P C U V W TE PE L 11 L 21 U V W P 1 Regenerative resistor OHS2 OHS1 Servo motor thermal relay Cooling fan BU BV BW 24VDC RA2 (Note 6) (Note 4) Servo motor thermal relay SON EMG 3-ph ase 200 t o 230VAC ALM DICOM DOCOM (Note 1) (Note 2 ...

  • Mitsumi electronic MR-J3- A - page 62

    3 - 9 3. SIGNALS AND WI RING (8) MR-J3-11KA4 to MR-J3-22KA4 External dynamic brake (option ) (Note 11) (Note 8 ) Stepdown transformer NFB L 1 L 2 L 3 P C U V W TE PE L 11 L 21 U V W P 1 Regenerative resistor OHS2 OHS1 Servo motor thermal relay Cooling fan BU BV BW 24VDC RA2 (Note 6) (Note 4) Servo motor thermal relay SON EMG 3-ph ase 380 t o 480VAC ...

  • Mitsumi electronic MR-J3- A - page 63

    3 - 10 3. SIGNALS AND WI RING 3.2 I/O signal connection example 3.2.1 Position control mode (Note 12) Plate Plate Servo amplifier 3 1 2 (Not e 7) CN6 (Note 2 ) Trouble (Note 6) Zero spe ed detection Limit ing to rque Encoder A-phase pulse (differential line driver) 21 DICOM 48 ALM 23 ZSP 25 TLC 24 INP 4L A 5L A R 6L B 7L B R 34 LG 33 OP 1P 1 5 R SD ...

  • Mitsumi electronic MR-J3- A - page 64

    3 - 11 3. SIGNALS AND WI RING Note 1. To prevent an electric shock, always connect the protective earth (PE) terminal (terminal mark ed ) of the servo amplifier to the protective earth (PE) of the control box. 2. Connect the diode in the correct direction. If it is connect ed reversely, the servo amplifier will be faulty and will not ou tput signal ...

  • Mitsumi electronic MR-J3- A - page 65

    3 - 12 3. SIGNALS AND WI RING 3.2.2 Speed control mode 3 1 2 (Note 7) CN6 Plate MO1 LG MO2 SD 2m max. Analog monitor 1 Analog monitor 2 (Note 10) USB cable (option) (Note 9 ) MR Configurator Person al computer Upper limit setting Emergency stop Servo-on Reset Speed selection 1 Speed selection 2 Forward rotation stroke end Reverse rotation stroke en ...

  • Mitsumi electronic MR-J3- A - page 66

    3 - 13 3. SIGNALS AND WI RING Note 1. To prevent an electric shock, always connect the protective earth (PE) terminal (terminal mark ed ) of the servo amplifier to the protective earth (PE) of the control box. 2. Connect the diode in the correct direction. If it is connect ed reversely, the servo amplifier will be faulty and will not ou tput signal ...

  • Mitsumi electronic MR-J3- A - page 67

    3 - 14 3. SIGNALS AND WI RING 3.2.3 Torque control mode 3 1 2 (Note 6) CN6 Plate MO1 LG MO2 SD 2m max. Analog monitor 1 Analog monitor 2 Encoder A-phase pulse (differenti al line driv er) Encoder B-phase pulse (differenti al line driv er) Contro l common Encoder Z-phase pulse (open col lector) Encoder Z-pha se pulse (differenti al line driv er) (No ...

  • Mitsumi electronic MR-J3- A - page 68

    3 - 15 3. SIGNALS AND WI RING Note 1. To prevent an electric shock, always connect t he protective earth (PE) terminal of the (termina l marked ) servo amplifi er to the protective earth (PE) of the control box. 2. Connect the diode in the correct direction. If it is connect ed reversely, the servo amplifier will be faulty and will not ou tput sign ...

  • Mitsumi electronic MR-J3- A - page 69

    3 - 16 3. SIGNALS AND WI RING 3.3 Explanation of power supply system 3.3.1 Signal explanations POINT For the layout of connector and termi nal block, refer to outline drawings in chapter 10. Abbreviation Connection target (application) Description L 1 L 2 L 3 Supply the following power to L 1 , L 2 , L 3 . For the 1-phase 200 to 23 0VAC power suppl ...

  • Mitsumi electronic MR-J3- A - page 70

    3 - 17 3. SIGNALS AND WI RING Abbreviation Connection target (application) Description U V W Servo motor power Connect to the servo motor power suppl y terminals (U, V, W). During power-on, do not open or close the motor power line. Otherwise, a malfunction or fault y may occur. N Return converter Brake unit When using the power regenerative conver ...

  • Mitsumi electronic MR-J3- A - page 71

    3 - 18 3. SIGNALS AND WI RING (3) Emergency stop CAUTION Provide an external emergency stop circ uit to ensure that opera tion can be stoppe d and power switched off immediately. Make up a circuit tha t shuts off main circuit power as soon as EMG is turned off at an emergency stop. When EMG is turned off, the dynamic brake is opera ted to bring th ...

  • Mitsumi electronic MR-J3- A - page 72

    3 - 19 3. SIGNALS AND WI RING 3.3.3 CNP1, CNP2, CNP3 wiring method POINT Refer to section 12.11 for the wire si zes used for wiring. MR-J3-500A or more MR-J3-350A4 or more does not have these connectors. Use the supplied servo amplifier power supply c onnectors for wir ing of CNP1, CNP2 and CNP3 . (1) MR-J3-10A to MR-J3-100A (a) Servo amplifier pow ...

  • Mitsumi electronic MR-J3- A - page 73

    3 - 20 3. SIGNALS AND WI RING (2) MR-J3-200A MR-J3-60A4 to MR-J3-200A4 (a) Servo amplifier power supply connectors <Applica ble cable exam ple> Cable finish OD: 4.1mm or less Servo a mplifie r Connector for CNP3 721-203/026-000(Plug) (WAGO) Servo amplifier power supply connectors CNP2 CNP1 CNP3 Connector for CNP1 721-207/026-000(Plug) (WAGO) ...

  • Mitsumi electronic MR-J3- A - page 74

    3 - 21 3. SIGNALS AND WI RING (3) MR-J3-350A (a) Servo amplifier power supply connectors Servo am plifier power s upply co nnecto rs CNP3 CNP1 CNP2 Connector for CNP1 PC 4/6-STF-7,62-CRWH (Phoenix Contact) <Applica ble cable exam ple> Cable finish OD: to 5mm Connector for CNP3 PC 4/3-STF-7,62-CRWH (Phoenix Contact) Connector for CNP2 54927-05 ...

  • Mitsumi electronic MR-J3- A - page 75

    3 - 22 3. SIGNALS AND WI RING (4) Insertion of cable into Molex and WAGO connectors Insertion of cable into 54928-0670, 54927-0520, 5492 8-0370 (Molex) connectors and 721-207/026-000, 721-205/026-000 and 721-203/026-000 (WAGO) connectors are as follows. The following explains for Molex, however use t he same procedures for inserting WAGO connectors ...

  • Mitsumi electronic MR-J3- A - page 76

    3 - 23 3. SIGNALS AND WI RING 2) Cable connection procedure 1) Attach the cable connection lever to the housing. (Detachable) 2) Push the cable connection lever in the direction of arrow. 3) Hold down the cable c onnection lever and insert the cable in the direction of arrow. 4) Release the cable connection lever . Cable connection lever ...

  • Mitsumi electronic MR-J3- A - page 77

    3 - 24 3. SIGNALS AND WI RING (b) Inserting the cable into the connector 1) Applicable flat-blade screwdriver dimen sions Always use the screwdriver shown here to do the work. [Unit: mm] 3 0.6 A pprox.R0.3 Approx.22 Approx.R0.3 3 to 3.5 2) When using the flat-blad e screwdriver - part 1 1) Insert the screwdriver into the square hole. Insert it alon ...

  • Mitsumi electronic MR-J3- A - page 78

    3 - 25 3. SIGNALS AND WI RING 3) When using the flat-blad e screwdriver - part 2 1) Insert the screwdriver into the square window at top of the connector. 2) Pus h the screw drive r in the direct ion of arrow . 3) With the sc rewdri ver pushed , insert the ca ble in the direction of arrow. (Insert the cable as far as it will go.) 4) Releasing the s ...

  • Mitsumi electronic MR-J3- A - page 79

    3 - 26 3. SIGNALS AND WI RING (5) How to insert the cable into Phoenix Contact connector POINT Do not use a precision driver be cause the cable cann ot be tightened with enough torque. Insertion of cables into Pho enix Contact connector PC 4/6-STF-7,62 -CRWH or PC 4/3-STF-7,62-CRWH is shown as follows. Before inserting the cable into the opening, m ...

  • Mitsumi electronic MR-J3- A - page 80

    3 - 27 3. SIGNALS AND WI RING 3.4 Connectors and signal arrangements POINT The pin configurations of the connectors are as viewed from the cable conn ector wiring section . Refer to (2) of this section for CN1 signal assignment. (1) Signal arrangement The servo amplifier front view shown is that of the MR-J3-20A or less. Re fer to chapter 10 Outlin ...

  • Mitsumi electronic MR-J3- A - page 81

    3 - 28 3. SIGNALS AND WI RING (2) CN1 signal assignment The signal assignment of connector changes with the control mode as indicated below. For the pins which are given parameter No.s in the related parameter column, their signals can b e changed using those parameters. Pin No. (Note 1) I/O (Note 2) I/O signals in control modes Related parameter N ...

  • Mitsumi electronic MR-J3- A - page 82

    3 - 29 3. SIGNALS AND WI RING Pin No. (Note 1) I/O (Note 2) I/O signals in control modes Related parameter No. P P/S S S/T T T/P 46 DOCOM DOCOM DOC OM DOCOM DOCOM DOCOM 47 DOCOM DOCOM DOC OM DOCOM DOCOM DOCOM 48 O ALM ALM ALM ALM ALM ALM 49 O RD RD RD RD RD RD PD18 5 0 Note 1. I: Input signal, O: Output signal 2. P: Position control mode, S: Speed ...

  • Mitsumi electronic MR-J3- A - page 83

    3 - 30 3. SIGNALS AND WI RING 3.5 Signal explanations For the I/O in terfaces (symbols in I/O division column in the table), refer to section 3.8 .2. In the control mode field o f the table P : Position control mode, S: Speed control mode, T: Torque control mode : Denotes that the signal may be used in the initial setting status. : Denotes that the ...

  • Mitsumi electronic MR-J3- A - page 84

    3 - 31 3. SIGNALS AND WI RING Device Symbol Connec- tor pin No. Functions/Applications I/O division Control mode P S T External torque limit selection TL CN1-18 Turn TL off to make Forward torque limit (paramete r No.PA11) and Reverse torque limit (parameter No.PA12) valid, or turn it on to make Analog torque limit (TLA) valid. For details, refer t ...

  • Mitsumi electronic MR-J3- A - page 85

    3 - 32 3. SIGNALS AND WI RING Device Symbol Connec- tor pin No. Functions/Applications I/O division Control mode P S T Speed selection 1 SP1 CN1- 41 <Speed co ntrol mode > Used to select th e command spee d for operation. When using SP 3, make it us able by maki ng the setti ng of param eter No.PD03 t o PD08, PD10 to PD12. DI-1 Speed selectio ...

  • Mitsumi electronic MR-J3- A - page 86

    3 - 33 3. SIGNALS AND WI RING Device Symbol Connec- tor pin No. Functions/Applications I/O division Control mode P S T Proportion control PC CN1-17 Turn PC on to switch the speed amplifier from the propo rtional integral type to the proportional type. If the servo motor at a stop is rotated even one pulse due to an y external factor, it generates t ...

  • Mitsumi electronic MR-J3- A - page 87

    3 - 34 3. SIGNALS AND WI RING Device Symbol Connec- tor pin No. Functions/Applications I/O division Control mode P S T Control change LOP CN1-45 <Pos ition/speed control change mode> Used to select the control mode in the position/speed control change mode. DI-1 Refer to Functions/ Appli- cations. (Note) LOP Control mode 0 Position 1 Speed No ...

  • Mitsumi electronic MR-J3- A - page 88

    3 - 35 3. SIGNALS AND WI RING (b) Output devices Device Symbol Connec- tor pin No. Functions/Applications I/O division Control mode P S T Trouble ALM CN1-48 ALM turns off when power is switched off or the protective circuit is activated to shut off the base ci rcuit. Without alarm occurring, ALM turns on within 1s after power-on. DO-1 Dynamic brake ...

  • Mitsumi electronic MR-J3- A - page 89

    3 - 36 3. SIGNALS AND WI RING Device Symbol Connec- tor pin No. Functions/Applications I/O division Control mode P S T Zero speed detection ZSP CN1-23 ZSP turns on when the servo motor speed is zero speed (50r/min) or less. Zero speed can be changed using parameter No.PC17. Example Zero speed is 50r/min OFF ON 0r/min 1) 2) 4) Forward rotation direc ...

  • Mitsumi electronic MR-J3- A - page 90

    3 - 37 3. SIGNALS AND WI RING Signal Symbol Connec- tor pin No. Functions/Applications I/O division Control mode P S T Alarm code ACD 0 CN1-24 To use this signal, set " 1 " in para meter No.PD24. This signal is output when an alar m occurs. When there is no alarm, respective ordinary signals (RD, INP, SA, ZSP) are output. Alarm codes and ...

  • Mitsumi electronic MR-J3- A - page 91

    3 - 38 3. SIGNALS AND WI RING (2) Input signals Signal Symbol Connec- tor pin No. Functions/Applications I/O division Control mode P S T Analog torque limit TLA CN1-27 To use this signal in the s peed control mode, set any of parameters No.PD13 to PD16, PD18 to make external torque limit selection (TL) available. When the analog torque limit (TLA) ...

  • Mitsumi electronic MR-J3- A - page 92

    3 - 39 3. SIGNALS AND WI RING (4) Communication POINT Refer to chapter 13 for the communi cation function. Signal Symbol Connec- tor pin No. Functions/Applications I/O division Control mode P S T RS-422 I/F SDP SDN RDP RDN CN3-5 CN3-4 CN3-3 CN3-6 Terminals for RS-422 communication. (Refer to cha pter 13.) (5) Power supply Signal Symbol Connec- tor ...

  • Mitsumi electronic MR-J3- A - page 93

    3 - 40 3. SIGNALS AND WI RING 3.6 Detailed description of the signal s 3.6.1 Position control mode (1) Pulse train input (a) Input pulse waveform s election Command pulses may be input in any of three differe nt forms, for which positive or negative logic can be chosen. Set the command pulse train form in paramet er No.PA13. Refer to section 5.1.10 ...

  • Mitsumi electronic MR-J3- A - page 94

    3 - 41 3. SIGNALS AND WI RING 2) Differential line driver sys tem Connect as shown below. Approx. 100 PP NP Servo amplifier PG NG SD (Note) Approx. 100 Note. Pulse train input interface is comprised of a photo coupler. Therefore, it may be any malfunctions si nce the current is reduced when connect a resistance to a pulse train signal line. The exp ...

  • Mitsumi electronic MR-J3- A - page 95

    3 - 42 3. SIGNALS AND WI RING (3) Ready (RD) Servo-on (SON) Alarm Ready (RD) ON OFF Yes No 100ms or less 10ms or less 10ms or less ON OFF (4) Electronic gear switching The combination of CM1 and CM2 g ives you a choice of four different electronic gear numerators set in the parameters. As soon as CM1/CM2 is turned ON or OFF, the molecule o f the el ...

  • Mitsumi electronic MR-J3- A - page 96

    3 - 43 3. SIGNALS AND WI RING A relationship between the applied voltage of the ana log torque limit (TLA) and th e torque limit value of the servo motor is shown below. To rque limit values will vary abou t 5 relative to the voltage depending on products. At the voltage of less than 0.05V, torque may vary as it may no t be limited sufficiently. Th ...

  • Mitsumi electronic MR-J3- A - page 97

    3 - 44 3. SIGNALS AND WI RING 3.6.2 Speed control mode (1) Speed setting (a) Speed command and speed The servo motor is run a t the speeds set in the par ame ters or at the speed set in th e applied voltage of the analog speed command (VC). A relationship between the analog speed command (VC) ap plied voltage and the servo motor speed is shown belo ...

  • Mitsumi electronic MR-J3- A - page 98

    3 - 45 3. SIGNALS AND WI RING (b) Speed selection 1 (SP1), speed selection 2 (SP2) and speed co mmand value Choose any of the speed settings made by the in te rnal speed commands 1 to 3 using speed se lection 1 (SP1) and speed selection 2 (SP2) or the speed setting made by the analog speed command ( VC). (Note) Input device Speed command value SP2 ...

  • Mitsumi electronic MR-J3- A - page 99

    3 - 46 3. SIGNALS AND WI RING 3.6.3 Torque control mode (1) Torque control (a) Torque command and torque A relationship between the applied voltage of the ana log torque command (TC) and the torque by the servo motor is shown below. The maximum torque is generated at 8V. Note that the torque at 8V input can be changed with parameter No.PC13. Forwa ...

  • Mitsumi electronic MR-J3- A - page 100

    3 - 47 3. SIGNALS AND WI RING (b) Analog torque command offset Using parameter No.PC38, the offset vo ltage of 999 to 999mV can be added to the TC applied voltage as shown below. 0 8( 8) Max. torque Generated torque TC applied vo ltage [V] Parameter No. PC38 offset range 999 to 999mV (2) Torque limit By setting parameter No.PA11 ( forward rotation ...

  • Mitsumi electronic MR-J3- A - page 101

    3 - 48 3. SIGNALS AND WI RING Generally, make connection as shown below. SP2 DOCOM P15R VLA LG SD SP1 Japan re sistor RRS10 or equivalent (Note) 2k 2k Servo amplifier Note. For the sink I/O interface. For the source I/O interface, refe r to section 3.8.3. (b) Speed selection 1(SP1)/speed selection 2(SP2) /sp eed selection 3(SP3) and s peed limit va ...

  • Mitsumi electronic MR-J3- A - page 102

    3 - 49 3. SIGNALS AND WI RING 3.6.4 Position/speed control chan ge mode Set " 1" in parameter No.PA01 to switch to the posit ion/speed control change mode. This functio n is not available in the absolute position detectio n system. (1) Control change (LOP) Use control change (LOP) to switch be tween the pos ition control mode and the spee ...

  • Mitsumi electronic MR-J3- A - page 103

    3 - 50 3. SIGNALS AND WI RING (3) Speed setting in speed control mode (a) Speed command and speed The servo motor is run a t the speed set in parameter No.8 (internal s peed command 1) or at the speed set in the applied voltage o f the analog speed co mman d (VC). A relationship between analog speed command (VC) applied voltage and servo motor spee ...

  • Mitsumi electronic MR-J3- A - page 104

    3 - 51 3. SIGNALS AND WI RING The speed may be changed during rota tion. In this case, the values set in parameters No.PC01 and PC02 are used for acceleration/deceleration. When the internal speed co mmand 1 to 7 is used to co mmand the speed, the speed does not vary with the ambient temperature. (c) Speed reached (SA) As in section 3.6.2 (2). 3.6. ...

  • Mitsumi electronic MR-J3- A - page 105

    3 - 52 3. SIGNALS AND WI RING (4) Speed limit in torque control mode (a) Speed limit value and speed The speed is limited to the limit value set in parameter No.8 (in ter nal speed limit 1) or the value set in the applied voltage of the analog speed limit (VLA). A r elationship between the an alog speed limit (VLA) applied voltage and the servo mo ...

  • Mitsumi electronic MR-J3- A - page 106

    3 - 53 3. SIGNALS AND WI RING 3.6.6 Torque/position co ntrol change mode Set " 5 " in p arameter No.PA01 to switc h to the torque/position control change mode. (1) Control change (LOP) Use control change (LOP) to switch be tween the torque control mode and the position contro l mode from an external contact. Relati onships between LOP and ...

  • Mitsumi electronic MR-J3- A - page 107

    3 - 54 3. SIGNALS AND WI RING 3.7 Alarm occurrence timing chart CAUTION When an alarm has occurred, remove its caus e, make sure that the operation signal is not being input, ensure safety, and rese t the alarm before restarting operation. As soon as an alarm occurs, turn off Servo-on (SON) and power o ff. When an alarm occurs in the servo amplifie ...

  • Mitsumi electronic MR-J3- A - page 108

    3 - 55 3. SIGNALS AND WI RING 3.8 Interfaces 3.8.1 Internal connection diagra m 10VDC D 3 DOCOM SON SON SON CN1 15 SP2 SP2 16 PC ST1 R S2 17 TL ST2 RS1 18 RES RES 1 9 CR SP1 41 EMG 42 LSP 43 LSN 44 LOP 45 46 OPC 12 20 47 PP 10 PG 11 NP 35 NG 36 LSP LSN LOP DICOM DOCOM LOP RES SP1 PST CN1 21 22 23 24 25 48 49 DICOM INP SA ZSP INP TLC RD ZSP TLC ALM ...

  • Mitsumi electronic MR-J3- A - page 109

    3 - 56 3. SIGNALS AND WI RING Note 1. P: Position control mode S: Speed control mode T: Torqu e control mode 2. For the differential line driver pulse train input. For the ope n collector pulse train input, make the following connection. DOCO 46 OPC 12 20 47 PP 10 PG 11 NP 35 NG 36 DICOM DOCOM 24VDC 3. For the sink I/O interface. For the sour ce I/ ...

  • Mitsumi electronic MR-J3- A - page 110

    3 - 57 3. SIGNALS AND WI RING (3) Pulse train input inter face DI-2 Give a pulse train signal in the differential line driver sys tem or open collector syste m. (a) Differential line driver system 1) Interface SD PG(NG) PP(NP) Max. input pulse frequency 1Mpps Servo am plifier Am26LS31 or equivalent Approx. 100 V OH V OL (Note) 10m or less : 2.5V : ...

  • Mitsumi electronic MR-J3- A - page 111

    3 - 58 3. SIGNALS AND WI RING 2) Input pulse condition 0.9 0.1 tc tHL tc tLH tF tLH=tHL<0.2 s tc>2 s tF>3 s PP NP (4) Encoder output pulse DO-2 (a) Open collector system Interface Max. output current: 35mA Photocoupler Servo amplifier OP LG SD Servo a mplifie r OP LG SD 5 to 24VDC (b) Differential line driver system 1) Interface Max. outpu ...

  • Mitsumi electronic MR-J3- A - page 112

    3 - 59 3. SIGNALS AND WI RING 2) Output pulse Servo motor CCW rotation LA LAR LB LBR LZ LZR T /2 OP Time cycle (T) is determined by the settings of parameter No.PA15 and PC19. 400 s or longer (5) Analog input Input impedance 10 to 12k Upper limit setti ng 2k 15VDC P15R VC, etc LG SD 2k Servo amplifier Approx. 10k (6) Analog output LG MO1 Servo a mp ...

  • Mitsumi electronic MR-J3- A - page 113

    3 - 60 3. SIGNALS AND WI RING 3.8.3 Source I/O interfaces In this servo amplifier, source type I/O interfaces c an be used. In this case, all DI-1 input signals a nd DO-1 output signals are of source type. Perform wiring according to the following interface s. (1) Digital input interface DI-1 Servo a mplifi er Switch Approx. 5mA V CES 1.0V I CEO 10 ...

  • Mitsumi electronic MR-J3- A - page 114

    3 - 61 3. SIGNALS AND WI RING 3.9 Treatment of cable shield external conductor In the case of the CN1 and CN2 connectors, securely connect the s hielded external conductor of the cable to the ground plate as shown in this sect ion and fix it to the connector shell. External conductor S heath Ext ernal cond uctor Pull back th e exte rnal conduc tor ...

  • Mitsumi electronic MR-J3- A - page 115

    3 - 62 3. SIGNALS AND WI RING 3.10 Connection of servo a mplifier and servo motor WARNING During power-on, do not open or clos e th e motor power line. O therwise, a malfunction or faulty may oc cur. 3.10.1 Connection instructions WARNING Insulate the connections o f the power supply terminals to prevent an electric shock. CAUTION Connect the wires ...

  • Mitsumi electronic MR-J3- A - page 116

    3 - 63 3. SIGNALS AND WI RING 3.10.2 Power supply cable wiring diagra ms (1) HF-MP series HF-KP series servo motor (a) When cable length is 10m or less CNP3 AWG 19 (red) AWG 19 (white) AWG 19 (black) AWG 19 (green/yellow) W V U Servo motor Servo amplifier 10m or l ess MR-PWS1CBL M-A1-L MR-PWS1CBL M-A2-L MR-PWS1CBL M-A1-H MR-PWS1CBL M-A2-H M U V W ( ...

  • Mitsumi electronic MR-J3- A - page 117

    3 - 64 3. SIGNALS AND WI RING (2) HF-SP series HC-RP series HC-UP series HC-LP series HA-LP502 HA-LP702 HF-JP series servo motor POINT Insert a contact in the direction shown in the figure. If inse rted in the incorrect direction, the contact is damaged and falls off. Model: C M10-SP10S- (D6) CM10-SP10S-VP-M CM10-AP10S- (D6) CM10-AP10S-VP-M Model: ...

  • Mitsumi electronic MR-J3- A - page 118

    3 - 65 3. SIGNALS AND WI RING 2) When the power supply connector and the electromagnetic brake connector are shared. Servo motor Servo a mplifie r 24VDC power supply for electromagnetic brake 50m or less RA1 Electroma gnetic brake interlock (MBR) RA2 M U V W U V W 24VDC ALM DOCOM DICOM MBR CN1 (Note 1) B1 B2 B RA1 RA2 (Note 3) RA3 Trouble (ALM) (No ...

  • Mitsumi electronic MR-J3- A - page 119

    3 - 66 3. SIGNALS AND WI RING Encoder connector signal allotment CM10-R10P Encoder connector signal allotment MS3102A20-29P Power supply connector signal allotment MS3102A18-10P MS3102A22-22P MS3102A32-17P CE05-2A32-17PD-B 5 6 1 4 View a 3 2 8 7 9 10 Terminal No. Signal Key A N G S R T P HF J E K D L M B C View a Pin Signal CD A B View b Terminal N ...

  • Mitsumi electronic MR-J3- A - page 120

    3 - 67 3. SIGNALS AND WI RING (3) HA-LP series servo motor POINT Refer to (2) in this section for HA-LP502, 702. (a) Wiring diagrams Refer to section 12.11 for the cables use d for wiring. 1) 200V class NFB MC 24VDC ALM DOCOM DICOM MBR CN1 Servo motor Servo amplifier M U V W U V W L 1 L 2 L 3 Cooling fan BU BV BW (Note 2) 50m or less RA1 RA2 (Note ...

  • Mitsumi electronic MR-J3- A - page 121

    3 - 68 3. SIGNALS AND WI RING 2) 400V class NFB MC 24VDC ALM DOCOM DICOM MBR CN1 Servo motor Servo amplifier M U V W U V W L 1 L 2 L 3 Cooling fa n BU BV BW (Note 2) 50m or less RA1 RA2 (Note 1) B1 B2 B OHS2 OHS1 Servo motor thermal relay RA3 24VDC (Not e 3) NFB 3-phase 380 to 480VAC 24VDC power supply for electromagnetic brake RA1 Electroma gnetic ...

  • Mitsumi electronic MR-J3- A - page 122

    3 - 69 3. SIGNALS AND WI RING (b) Servo motor terminals Terminal box Encoder connector CM10-R10P Brake connector MS3102A10SL-4P Encoder connector signal allotment CM10-R10P 5 6 1 4 3 2 8 7 9 10 Terminal No. Signal Brake connector signal allotment MS3102A10SL-4P 1 2 Terminal No. Signal 1 MR 1 B1 (Note) 2 MRR 3 2 B2 (Note) 4 BAT 5 LG Note. For the mo ...

  • Mitsumi electronic MR-J3- A - page 123

    3 - 70 3. SIGNALS AND WI RING Te rminal box inside (HA -LP801(4) 12K1(4) 11K1M(4) 15K1M(4) 15K2 (4) 22 K2(4) Thermal sensor terminal block (OHS1 OHS2) M4 screw Cooling fan terminal block (BU BV BW) M4 screw Encoder connector CM10-R10P Motor power supply terminal block (U V W) M8 screw Earth terminal( ) M6 screw Terminal block signal arrangement UV ...

  • Mitsumi electronic MR-J3- A - page 124

    3 - 71 3. SIGNALS AND WI RING Terminal box inside (HA-LP25K1) OHS2 OHS1 BW BV BU W V U Encoder connector CM10-R10P Thermal sensor terminal block Cooling fan terminal block (OHS1 OHS2) M4 screw (BU BV BW) M4 screw Motor power supply terminal block (U V W) M10 screw Earth terminal( ) M6 screw Terminal block signal arra ngement BV UV W BU BW OHS1 OHS2 ...

  • Mitsumi electronic MR-J3- A - page 125

    3 - 72 3. SIGNALS AND WI RING Signal name Abbreviation Description Power supply U V W Connect to the m otor output terminals (U, V, W) of the servo amplifier. During po wer-on, do not open or close the motor power line. Otherwise, a malfunction or fault y may occur. Cooling fan (Note) BU BV BW Supply power which satisfies the following specificatio ...

  • Mitsumi electronic MR-J3- A - page 126

    3 - 73 3. SIGNALS AND WI RING 3.11 Servo motor with an electromagneti c brake 3.11.1 Safety precautions CAUTION Configure an electromagnetic brake circuit so t hat it is activated also by an external emergency stop switch. B U SON RA Contacts must be opened by an emergency stop switch. Contacts must be opened by servo-on (SON) OFF, trouble (ALM) an ...

  • Mitsumi electronic MR-J3- A - page 127

    3 - 74 3. SIGNALS AND WI RING 3.11.3 Timing charts (1) Servo-on (SON) command (from controller) ON/OFF Tb [ms] after the servo-on (SON) signal is switched o ff, the servo lock is released and the servo motor coasts. If the electromagnetic brake is made valid in the servo lock status , the brake life may be shorter. Therefore, when using the electro ...

  • Mitsumi electronic MR-J3- A - page 128

    3 - 75 3. SIGNALS AND WI RING (3) Alarm occurrence Servo motor speed ON OFF Base circuit Electromagnetic brake interlock (MBR) (Note) ON OFF Trouble (ALM) No (ON) Yes (OFF) Dynamic brake Dynamic brake Electromagnetic brake Electromagnetic brake operation delay time Electromagnetic brake (10ms) Note. ON: Electromagnetic brake is not activated. OFF: ...

  • Mitsumi electronic MR-J3- A - page 129

    3 - 76 3. SIGNALS AND WI RING (5) Only main circuit power supply off (co ntrol circuit power supply remains on) Servo mo tor speed ON OFF Base circuit Electromagnetic brak e inte rlock (MBR) (Note 2) ON OFF Trou ble ( ALM) No (ON) Yes (OFF ) ON OFF Main circuit power supply Dynamic brake Dynamic brake Elect romagn etic brake Electromagnetic brake E ...

  • Mitsumi electronic MR-J3- A - page 130

    3 - 77 3. SIGNALS AND WI RING (2) When cable length exceeds 10m When the cable length exce eds 10m, fabricate an extens ion cable as shown below on the customer side. In this case, the motor brake cable should be within 2m lo ng. Refer to section 12.11 for the wire used for the extension cable. (Note 2) a) Relay connector for extension cable B MR-B ...

  • Mitsumi electronic MR-J3- A - page 131

    3 - 78 3. SIGNALS AND WI RING 3.12 Grounding WARNING Ground the servo amplifier and servo motor securely. To prevent an electric shock, alwa ys co nnect the prote ctive earth (PE) terminal (terminal marked ) of the servo amp lifier with the protective earth (PE) of the control box. The servo amplifier switches the pow er transistor on-off to supply ...

  • Mitsumi electronic MR-J3- A - page 132

    4 - 1 4. STARTUP 4. STARTUP WARNIN G Do not operate the switches with wet ha nds. You may get an electric shock. CAUTION Before starting operation, check the par ameters. Some machines may per form unexpected operation. Take safety measures, e.g. provide covers , to prevent accidental contact of hands and parts (cables, etc.) with the servo amplifi ...

  • Mitsumi electronic MR-J3- A - page 133

    4 - 2 4. STARTUP 4.1.2 Wiring check (1) Power supply system wiring Before switching on the main circuit and control ci rcuit power supplies, check the following items. (a) Power supply system wiring The power supplied to the p ower input terminals (L 1 , L 2 , L 3 , L 11 , L 21 ) of the servo a mplifier should satisfy the defined specifications. (R ...

  • Mitsumi electronic MR-J3- A - page 134

    4 - 3 4. STARTUP 2) When regenerative option is used over 5kW for 200V class and 3.5kW for 400 V class The lead of built-in regener ative resistor connected to P termina l and C ter minal of TE1 terminal block should not be connected. The generative brake option should be c onnected to P terminal and C terminal. A twisted cable should be us ed w he ...

  • Mitsumi electronic MR-J3- A - page 135

    4 - 4 4. STARTUP 4.2 Startup in position control mod e Make a startup in accordance with section 4.1. This section provides the methods specific to the position control mode. 4.2.1 Power on and off procedures (1) Power-on Switch power on in the following procedure. Al ways follow this pr ocedure at power-on. 1) Switch off the servo-on (SON). 2) Mak ...

  • Mitsumi electronic MR-J3- A - page 136

    4 - 5 4. STARTUP 4.2.3 Test operation Before starting actual operation , perform test operatio n to make sur e that the machine operate s normally. Refer to section 4.2.1 for th e power on and off methods of the servo amplifier. Test operation of servo motor alone in JOG operation of test operation mode In this step, confirm that t he servo amplifi ...

  • Mitsumi electronic MR-J3- A - page 137

    4 - 6 4. STARTUP 4.2.4 Parameter setting POINT The encoder cable MR-EKCBL M-L/H for the HF-MP series HF-KP series servo motor or the encoder cable M R-ENECBL M-H for HF-JP11K1M(4) 15K1M(4) servo motor req uires the parameter No.PC22 setting to be changed depending on its length. Check wh ether the pa rameter is set correct ly. If it is not set corr ...

  • Mitsumi electronic MR-J3- A - page 138

    4 - 7 4. STARTUP 4.2.5 Actual operation Start actual operation a fter confirmation of normal operation by test o peration and completion of the corresponding parameter settings. Perform a home position return as necessary. 4.2.6 Trouble at start-up CAUTION Excessive adjustment or change of para meter setting must not be made as it will make operati ...

  • Mitsumi electronic MR-J3- A - page 139

    4 - 8 4. STARTUP No. Start-up sequence Fault Investigation Possible cause Reference 4 Gain adjustment Rotation ripples (speed fluctuations) are large at low speed. Make gain adjustment in the following procedure. 1. Increase the auto tuning response level. 2. Repeat acceleration and deceleration several times to complete auto tuning. Gain adjustmen ...

  • Mitsumi electronic MR-J3- A - page 140

    4 - 9 4. STARTUP Check for a position shift in the following sequence. 1) When Q P Noise entered the pulse trai n signal wiring betw een positioning unit and servo amplifier, causin g pulses to be miss-counted. (Cause A) Make the following check or take the following measures. Check how the shielding is done. Change the open collector system to th ...

  • Mitsumi electronic MR-J3- A - page 141

    4 - 10 4. STARTUP 4.3.2 Stop In any of the following s tatuses, the servo amplifier interrupts and sto ps the operation of the servo motor. Refer to section 3.11 for the servo motor with an electromagnetic brake. (a) Servo-on (SON) OFF The base circuit is shut off and the servo motor coasts. (b) Alarm occurrence When an alarm occurs, the base circu ...

  • Mitsumi electronic MR-J3- A - page 142

    4 - 11 4. STARTUP 4.3.3 Test operation Before starting actual operation , perform test operatio n to make sur e that the machine operate s normally. Refer to section 4.3.1 for th e power on and off methods of the servo amplifier. Test operation of servo motor alone in JOG operation of test operation mode In this step, confirm that t he servo amplif ...

  • Mitsumi electronic MR-J3- A - page 143

    4 - 12 4. STARTUP 4.3.4 Parameter setting POINT The encoder cable MR-EKCBL M-L/H for the HF-MP series HF-KP series servo motor or the encoder cable M R-ENECBL M-H for HF-JP11K1M(4) 15K1M(4) servo motor req uires the parameter No.PC22 setting to be changed depending on its length. Check wh ether the pa rameter is set correct ly. If it is not set cor ...

  • Mitsumi electronic MR-J3- A - page 144

    4 - 13 4. STARTUP 4.3.5 Actual operation Start actual operation a fter confirmation of normal operation by test o peration and completion of the corresponding parameter settings. 4.3.6 Trouble at start-up CAUTION Excessive adjustment or ch ange of parameter se tting must not be made as it will make operation instable. POINT Using the MR Configurato ...

  • Mitsumi electronic MR-J3- A - page 145

    4 - 14 4. STARTUP No. Start-up sequence Fault Investigation Possible cause Reference 4 Gain adjustment Rotation ripples (speed fluctuations) are large at low speed. Make gain adjustment in the following procedure. Increase the auto tuning response level. Repeat acceleration and deceleration several times to complete auto tuning. Gain adjustment fau ...

  • Mitsumi electronic MR-J3- A - page 146

    4 - 15 4. STARTUP 4.4.2 Stop In any of the following s tatuses, the servo amplifier interrupts and sto ps the operation of the servo motor. Refer to section 3.11 for the servo motor with an electromagnetic brake. (a) Servo-on (SON) OFF The base circuit is shut off and the servo motor coasts. (b) Alarm occurrence When an alarm occurs, the base circu ...

  • Mitsumi electronic MR-J3- A - page 147

    4 - 16 4. STARTUP 4.4.3 Test operation Before starting actual operation , perform test operatio n to make sur e that the machine operate s normally. Refer to section 4.4.1 for th e power on and off methods of the servo amplifier. Test operation of servo motor alone in JOG operation of test operation mode In this step, confirm that t he servo amplif ...

  • Mitsumi electronic MR-J3- A - page 148

    4 - 17 4. STARTUP 4.4.4 Parameter setting POINT The encoder cable MR-EKCBL M-L/H for the HF-MP series HF-KP series servo motor or the encoder cable M R-ENECBL M-H for HF-JP11K1M(4) 15K1M(4) servo motor req uires the parameter No.PC22 setting to be changed depending on its length. Check wh ether the pa rameter is set correct ly. If it is not set cor ...

  • Mitsumi electronic MR-J3- A - page 149

    4 - 18 4. STARTUP 4.4.5 Actual operation Start actual operation a fter confirmation of normal operation by test o peration and completion of the corresponding parameter settings. 4.4.6 Trouble at start-up CAUTION Excessive adjustment or ch ange of parameter se tting must not be made as it will make operation instable. POINT Using the MR Configurato ...

  • Mitsumi electronic MR-J3- A - page 150

    5 - 1 5. PARAMETERS 5. PARAMETERS CAUTION Never adjust or change the parameter va lues extremely as it will make operation instable. When a fixed number is indicated in each digit of a parameter, do not change the value by any means. In this servo amplifier, the parameters are cla ssified in to the following groups on a function basis. Parameter gr ...

  • Mitsumi electronic MR-J3- A - page 151

    5 - 2 5. PARAMETERS No. Symbol Name Initial value Unit Control mode Position Speed Torque PA16 For manufacturer setting 0000h PA17 0000h PA18 0000h PA19 *BLK Parameter write inhibit 000Bh 5.1.2 Parameter write inhibit Parameter Initial value Unit Setting range Control mode No. Symbol Name Position Speed Torque PA19 *BLK Parameter write inhibit 000B ...

  • Mitsumi electronic MR-J3- A - page 152

    5 - 3 5. PARAMETERS 5.1.3 Selection of control mode Parameter Initial value Unit Setting range Control mode No. Symbol Name Position Speed Torque PA01 *STY Control mode 0000h Refer to the text. POINT Turn off the power and then on agai n after setting the parameter to validate the parameter value. This parameter is supported by a combination of a s ...

  • Mitsumi electronic MR-J3- A - page 153

    5 - 4 5. PARAMETERS Set the control mode and c ontrol loop composition of t he servo a mplifier, and the maximum torque of the HF- KP series servo motor. By making the high-response control valid in the contro l loop composition , response of the servo can be increased compared to the response under the stand ard contro l (factory setting).Moreover ...

  • Mitsumi electronic MR-J3- A - page 154

    5 - 5 5. PARAMETERS 5.1.4 Selection of regenerative option Parameter Initial value Unit Setting range Control mode No. Symbol Name Position Speed Torque PA02 *REG Regenerative option 0000h Refer to the text. POINT Turn off the power and then on agai n after setting the parameter to validate the parameter value. Incorrect setting may cause the reg e ...

  • Mitsumi electronic MR-J3- A - page 155

    5 - 6 5. PARAMETERS 5.1.5 Using absolute position dete ction system Parameter Initial value Unit Setting range Control mode No. Symbol Name Position Speed Torque PA03 *ABS Absolute position detection system 0000h Refer to the text. POINT Turn off the power and then on agai n after setting the parameter to validate the parameter value. Set this para ...

  • Mitsumi electronic MR-J3- A - page 156

    5 - 7 5. PARAMETERS 5.1.7 Number of command input pulses per servo motor revolution Parameter Initial value Unit Setting range Control mode No. Symbol Name Position Speed Torque PA05 *FBP Number of command input pulses per revolution 0 0 1000 to 50000 POINT Turn off the power and then on agai n after setting the parameter to validate the parameter ...

  • Mitsumi electronic MR-J3- A - page 157

    5 - 8 5. PARAMETERS 5.1.8 Electronic gear Parameter Initial value Unit Setting range Control mode No. Symbol Name Position Speed Torque PA06 CMX Electronic gear numerator (command pulse multiplying factor numerator) 1 1 to 1048576 PA07 CDV Electronic gear denominator (command pulse multiplying factor denominator) 1 1 to 1048576 CAUTION Incorrect se ...

  • Mitsumi electronic MR-J3- A - page 158

    5 - 9 5. PARAMETERS (a) For motion in increments of 10 m per pulse Machine specifications Ball screw lead Pb 10 [mm] Reduction ratio: 1/n Z 1 /Z 2 1/2 Z 1 : Number of gear teeth at the servo m otor side Z 2 : Number of gear teeth at the load sid e Encod er reso lution of se rvo motor 26214 4[puls e/rev ] Pb 10 [mm] Z 1 1/n 1/n Z 1 /Z 2 1/2 Z 2 Enco ...

  • Mitsumi electronic MR-J3- A - page 159

    5 - 10 5. PARAMETERS (2) Instructions for reduction The calculated value befor e reduction must be as nea r as possible to the calculated value af ter reduction. In the case of (1), (b) in this section, an error will be smaller if reduction is m ade to provide no fra ction for CDV. The fraction of Expre ssion (5.1) before reduction is calculated as ...

  • Mitsumi electronic MR-J3- A - page 160

    5 - 11 5. PARAMETERS To rotate the servo motor at 3000r/min in the open co llector system (200kpulse/s), set the electronic gear as follows. CDV CMX N 0 f 60 Pt f : Input pulses frequency [pulse/s] N 0 : Servo motor speed [r/min] Pt : Encoder resolution of servo motor [pulse/rev] 200 60 CDV CMX 3000 262144 CDV CMX 3000 60 262144 200 60 200000 3000 ...

  • Mitsumi electronic MR-J3- A - page 161

    5 - 12 5. PARAMETERS 5.1.9 Auto tuning Parameter Initial value Unit Setting range Control mode No. Symbol Name Position Speed Torque PA08 ATU Auto tuning mode 0001h Refer to the text. PA09 RSP Auto tuning response 12 1 to 32 Make gain adjustment using auto tuning . Refer to section 7.2 for details. (1) Auto tuning mode (parameter No .PA08) Select t ...

  • Mitsumi electronic MR-J3- A - page 162

    5 - 13 5. PARAMETERS (2) Auto tuning response (parameter No.PA09) If the machine hunts or gen erates large gear sound, de crease the set value. To improve per formance, e.g. shorten the settling time, increase the set va lue. Setting Response Guideline for machine resonance frequency [Hz] Setting Response Guideline for machine resonance frequency [ ...

  • Mitsumi electronic MR-J3- A - page 163

    5 - 14 5. PARAMETERS 5.1.11 Torque limit Parameter Initial value Unit Setting range Control mode No. Symbol Name Position Speed Torque PA11 TLP Forward rotation torque limit 100.0 0 to 100.0 PA12 TLN Reverse rotation torque limit 100.0 0 to 100.0 The torque generated by th e servo motor can be limite d . Refer to section 3 .6.1 (5) and use these pa ...

  • Mitsumi electronic MR-J3- A - page 164

    5 - 15 5. PARAMETERS 5.1.12 Selection of command pulse inp ut form Parameter Initial value Unit Setting range Control mode No. Symbol Name Position Speed Torque PA13 *PLSS Command pulse input form 0000h Refer to the text. POINT Turn off the power and then on agai n after setting the parameter to validate the parameter value. Select the input form o ...

  • Mitsumi electronic MR-J3- A - page 165

    5 - 16 5. PARAMETERS 5.1.13 Selection of servo motor rotation direction Parameter Initial value Unit Setting range Control mode No. Symbol Name Position Speed Torque PA14 *POL Rotation direction selection 0 0 1 POINT Turn off the power and then on agai n after setting the parameter to validate the parameter value. Select servo motor rotation direct ...

  • Mitsumi electronic MR-J3- A - page 166

    5 - 17 5. PARAMETERS (1) For output pulse designation Set " 0 " (initial value) in parameter No .PC19. Set the number of pulses per servo moto r revolution. Output pulse set value [pulses/rev ] For instance, set "5600" to parameter No.PA15, t he actually outpu t A/B-phase pulses are as indicated below. 4 5600 A/B-phase outpu t p ...

  • Mitsumi electronic MR-J3- A - page 167

    5 - 18 5. PARAMETERS 5.2 Gain/filter parameters (No.PB ) POINT For any parameter whose symbol i s preceded by *, set the parameter value and switch power off once, then switch it on again to make that parameter setting valid. 5.2.1 Parameter list No. Symbol Name Initial value Unit Control mode Position Speed Torque PB01 FILT Adaptive tuning mode (A ...

  • Mitsumi electronic MR-J3- A - page 168

    5 - 19 5. PARAMETERS No. Symbol Name Initial value Unit Control mode Position Speed Torque PB35 For manufacturer setting 0.00 PB36 0.00 PB37 100 PB38 0.0 PB39 0.0 PB40 0.0 PB41 1125 PB42 1125 PB43 0004h PB44 0000h PB45 CNHF Vibration suppression control filter 2 0000h ...

  • Mitsumi electronic MR-J3- A - page 169

    5 - 20 5. PARAMETERS 5.2.2 Detail list No. Symbol Name and function Initial value Unit Setting range Control mode Position Speed Torque PB01 FILT Adaptive tuning mode (adaptive fi lter ) Select the setting method for filter tuning. Setting this parameter to " 1" (filter tuning mod e) automatically changes the machine resonance suppression ...

  • Mitsumi electronic MR-J3- A - page 170

    5 - 21 5. PARAMETERS No. Symbol Name and function Initial value Unit Setting range Control mode Position Speed Torque PB02 VRFT Vibration suppression control tuning mode (advanced vibration suppression control) The vibration suppression is valid when the parameter No.PA08 (auto tuning mode) setting is " 2" or " 3". When PA08 is ...

  • Mitsumi electronic MR-J3- A - page 171

    5 - 22 5. PARAMETERS No. Symbol Name and function Initial value Unit Setting range Control mode Position Speed Torque PB 03 PS T Position c ommand accele ration/decele ration time c onstant (position smoothing) Used to set th e time constan t of a low-p ass filter in response to the position c ommand. You can use parameter N o.PB25 to ch oose the p ...

  • Mitsumi electronic MR-J3- A - page 172

    5 - 23 5. PARAMETERS No. Symbol Name and function Initial value Unit Setting range Control mode Position Speed Torque PB05 For manufacturer setting Do not change this value by any means. 500 PB06 GD2 Ratio of load iner tia moment to servo motor inertia moment Used to set the ratio of the load inertia moment to the servo motor shaft inertia moment. ...

  • Mitsumi electronic MR-J3- A - page 173

    5 - 24 5. PARAMETERS No. Symbol Name and function Initial value Unit Setting range Control mode Position Speed Torque PB12 OVA (Note) Overshoot amount compensation Used to suppress overshoot in position control. Overshoot can be suppressed in machines with high friction. Set a control ratio against the friction torque in percentage unit. Overshoot ...

  • Mitsumi electronic MR-J3- A - page 174

    5 - 25 5. PARAMETERS No. Symbol Name and function Initial value Unit Setting range Control mode Position Speed Torque PB15 NH2 Machine resonance suppression filter 2 Set the notch frequency of the machine resonance suppression filter 2. Set parameter No.PB16 (notch shape selection 2) to " 1" to make this parameter valid. 4500 Hz 100 to 45 ...

  • Mitsumi electronic MR-J3- A - page 175

    5 - 26 5. PARAMETERS No. Symbol Name and function Initial value Unit Setting range Control mode Position Speed Torque PB23 VFBF Low-pass filter selection Select the low-pass filter. Low-pass filter selec tion 0: Automatic setting 1: Manual settin g (parameter No.PB1 8 setting) 00 0 When automatic setting has been selected, select the filter that ha ...

  • Mitsumi electronic MR-J3- A - page 176

    5 - 27 5. PARAMETERS No. Symbol Name and function Initial value Unit Setting range Control mode Position Speed Torque PB27 CDL Gain changing condition Used to set the value of gain changing condition (command frequency, droop pulses, servo motor speed) selected in parameter No.PB26.The set value unit changes with the changing condition item. (Refer ...

  • Mitsumi electronic MR-J3- A - page 177

    5 - 28 5. PARAMETERS No. Symbol Name and function Initial value Unit Setting range Control mode Position Speed Torque PB35 For man ufacturer setting 0.00 PB36 Do not change this value by any means. 0.00 PB37 100 PB38 0.0 PB39 0.0 PB40 0.0 PB41 1125 PB42 1125 PB43 0004h PB44 0000h PB45 CNHF (Note 1) Vibration suppression control filter 2 Used to set ...

  • Mitsumi electronic MR-J3- A - page 178

    5 - 29 5. PARAMETERS 5.2.3 Position smoothing By setting the position command acceleration/deceleratio n time constant (parameter No.PB03), you can run the servo motor smoothly in response to a sudden position command. The following diagrams show the operatio n patterns of the servo motor in respons e to a position command when you have set the pos ...

  • Mitsumi electronic MR-J3- A - page 179

    5 - 30 5. PARAMETERS 5.3 Extension setting parameters (No.PC ) POINT For any parameter whose symbol i s preceded by *, set the parameter value and switch power off once, then switch it on again to make that parameter setting valid. 5.3.1 Parameter list No. Symbol Name Initial value Unit Control mode Position Speed Torque PC01 STA Acceleration time ...

  • Mitsumi electronic MR-J3- A - page 180

    5 - 31 5. PARAMETERS No. Symbol Name Initial value Unit Control mode Position Speed Torque PC34 CMX4 Command pulse multiplying factor numerator 4 1 PC35 TL2 Internal torque limit 2 100.0 PC36 *DMD Status display selection 0000h PC37 VCO Analog speed command offset 0 mV Analog speed limit offset PC38 TPO Analog torque command offset 0 mV Analog torq ...

  • Mitsumi electronic MR-J3- A - page 181

    5 - 32 5. PARAMETERS No. Symbol Name and function Initial value Unit Setting range Control mode Position Speed Torque PC03 STC S-pattern acceleration/deceleration time constant Used to smooth start/stop of the servo motor. Set the time of the arc part for S-pattern acceleration/ deceleration. STA: Accele ration time const ant (paramete r No.PC01) S ...

  • Mitsumi electronic MR-J3- A - page 182

    5 - 33 5. PARAMETERS No. Symbol Name and function Initial value Unit Setting range Control mode Position Speed Torque PC06 SC2 Internal speed command 2 Used to set speed 2 of internal speed commands. 500 r/min 0 to instan- taneous permi- ssible speed Internal speed limit 2 Used to set speed 2 of internal speed limits. PC07 SC3 Internal speed comman ...

  • Mitsumi electronic MR-J3- A - page 183

    5 - 34 5. PARAMETERS No. Symbol Name and function Initial value Unit Setting range Control mode Position Speed Torque PC13 TLC Analog torque co mmand maximum output Used to set the output torque at the analog torque command voltage (TC 8V) of 8V on the ass umption that the maximum torque is 100[ ]. For example, set 50 to o utput (maximum torque 50/ ...

  • Mitsumi electronic MR-J3- A - page 184

    5 - 35 5. PARAMETERS No. Symbol Name and function Initial value Unit Setting range Control mode Position Speed Torque PC18 *BPS Alarm history clear Used to clear the alarm history. Alarm history cl ear 0: Invalid 1: Valid When alarm history clear is made va lid, the alarm history is cleared at next power-on. After the alarm history is cleared, the ...

  • Mitsumi electronic MR-J3- A - page 185

    5 - 36 5. PARAMETERS No. Symbol Name and function Initial value Unit Setting range Control mode Position Speed Torque PC22 *COP1 Function selection C-1 Select the execution of automatic restart after instantaneous power failure selection, and encoder cable communication system selection. 00 Restart a fter inst antaneou s power failure selection If ...

  • Mitsumi electronic MR-J3- A - page 186

    5 - 37 5. PARAMETERS No. Symbol Name and function Initial value Unit Setting range Control mode Position Speed Torque PC23 *COP2 Function selection C-2 Select the servo lock at speed control mode stop, the VC- VLA voltage averaging, and the speed limit in torque control mode. Selection of servo lock at stop In the speed control mode, the servo moto ...

  • Mitsumi electronic MR-J3- A - page 187

    5 - 38 5. PARAMETERS No. Symbol Name and function Initial value Unit Setting range Control mode Position Speed Torque PC26 *COP5 Function selection C-5 Select the stroke limit warning (AL. 99). Stroke limit warning (AL. 99) sele ction 0: Valid 1: Invali d When this para m eter is set to "1", AL. 99 will not occur if the forward rotation s ...

  • Mitsumi electronic MR-J3- A - page 188

    5 - 39 5. PARAMETERS No. Symbol Name and function Initial value Unit Setting range Control mode Position Speed Torque PC35 TL2 Internal torq ue limit 2 Set this parameter to limit servo motor torque on the assumption that the maximum torque is 100[ ]. When 0 is set, torque is not produced. When torque is output in analog monitor output, this set va ...

  • Mitsumi electronic MR-J3- A - page 189

    5 - 40 5. PARAMETERS No. Symbol Name and function Initial value Unit Setting range Control mode Position Speed Torque PC37 VCO Analog speed command offset Used to set the offset voltage of the analog speed command (VC). For example, if CCW rotation is provided by switching on forward rotation start (ST1) with 0V applied to VC, set a negative value. ...

  • Mitsumi electronic MR-J3- A - page 190

    5 - 41 5. PARAMETERS 5.3.3 Analog monitor The servo status can be output to two channels in terms of voltage . (1) Setting Change the following digits of parameter No.PC14, PC15. Analog monito r (MO1) output selec tion (Sign al outp ut to across MO1-L G) Parameter No.PC14 000 Para mete r No.P C15 Analog monitor (MO2) output selection (Sign al outp ...

  • Mitsumi electronic MR-J3- A - page 191

    5 - 42 5. PARAMETERS Setting Output item Description Setting Output item Description 6 Droop pulses (N ote) ( 10V/100 pulses) 100[pulse] CW direction CCW direction 100[pulse] 0 10[V] -10[V] 7 Droop pulses (N ote) ( 10V/1000 pulses) 1M[pulse] CW direction CCW direction 1M[pulse] 0 10[V] -10[V] 8 Droop pulses (Note 1) ( 10V/10000 pulses) 10000[pulse] ...

  • Mitsumi electronic MR-J3- A - page 192

    5 - 43 5. PARAMETERS (3) Analog monitor block diagram PWM M Feedba ck position Home position (CR input position) Current control Speed control Current command Position control Droop p uls e Differ- entia l Comma nd pulse frequency Bus voltage Speed command Command pulse Curren t feed back Posit ion fee dback Servo Mot or speed Curren t encoder Serv ...

  • Mitsumi electronic MR-J3- A - page 193

    5 - 44 5. PARAMETERS 5.4 I/O setting parameters (No.PD ) POINT For any parameter whose symbol i s preceded by *, set the parameter value and switch power off once, then switch it on again to make that parameter setting valid. 5.4.1 Parameter list No. Symbol Name Initial value Unit Control mode Position Speed Torque PD01 *DIA1 Input signal automatic ...

  • Mitsumi electronic MR-J3- A - page 194

    5 - 45 5. PARAMETERS 5.4.2 List of details No. Symbol Name and function Initial value Unit Setting range Control mode Position Speed Torque PD01 *DIA1 Input signal automatic ON selection 1 Select the input devices to be automatically turned ON. 0 0 0 BIN 0: U sed as ex ternal in put sign al BIN 1: Autom atic ON Initial value BIN HEX Signal na m e 0 ...

  • Mitsumi electronic MR-J3- A - page 195

    5 - 46 5. PARAMETERS No. Symbol Name and function Initial value Unit Setting range Control mode Position Speed Torque PD03 *DI1 Input signal device selection 1 (CN1-15) Any input signal can be assigned to the CN1-15 pin. Note that the setting digits and the signal that can be assigned change depending on the control mode. 0 Position contr ol Speed ...

  • Mitsumi electronic MR-J3- A - page 196

    5 - 47 5. PARAMETERS No. Symbol Name and function Initial value Unit Setting range Control mode Position Speed Torque PD05 *DI3 Input signal device selection 3 (CN1-17) Any input signal can be assigned to the CN1-17 pin. The devices that can be assigned and the setting method are the same as in parameter No.PD03. 0 Position control mode Speed contr ...

  • Mitsumi electronic MR-J3- A - page 197

    5 - 48 5. PARAMETERS No. Symbol Name and function Initial value Unit Setting range Control mode Position Speed Torque PD10 *DI8 Input signal device selection 8 (CN1-43) Any input signal can be assigned to the CN1-43 pin. The devices that can be assigned and the setting method are the same as in parameter No.PD03. 0 Position control mode Speed contr ...

  • Mitsumi electronic MR-J3- A - page 198

    5 - 49 5. PARAMETERS No. Symbol Name and function Initial value Unit Setting range Control mode Position Speed Torque PD13 *DO1 Output signal de vice selection 1 (CN1-22) Any output signal can be assigned to the CN1-22 pin. In the initial setting, INP is assigned in the position control mode, and SA is assigned in the speed control mode. Note that ...

  • Mitsumi electronic MR-J3- A - page 199

    5 - 50 5. PARAMETERS No. Symbol Name and function Initial value Unit Setting range Control mode Position Speed Torque PD14 *DO2 Output signal de vice selection 2 (CN1-23) Any output signal can be assigned to the CN1-23 pin. In the initial setting, ZSP is assigned to the pin. The devices that can be assigned and the setting method are the same as in ...

  • Mitsumi electronic MR-J3- A - page 200

    5 - 51 5. PARAMETERS No. Symbol Name and function Initial value Unit Setting range Control mode Position Speed Torque PD19 *DIF Input filter setting Select the input filter. 000 Input si gnal filter If extern al input signa l causes chattering due to noise, etc., inp ut filter is used to suppress i t. 0: None 1: 1.777[ m s] 2: 3.555[ m s] 3: 5.333[ ...

  • Mitsumi electronic MR-J3- A - page 201

    5 - 52 5. PARAMETERS No. Symbol Name and function Initial value Unit Setting range Control mode Position Speed Torque PD24 *DOP5 Function selection D-5 Select the alarm code and warning (WNG) outputs. 00 Settin g of alarm code out put Conn ector pins of CN1 Set val ue 22 23 24 0 Alarm code is not output. 1 88888 AL.12 AL.13 AL.15 AL.17 AL.8A AL.8E ...

  • Mitsumi electronic MR-J3- A - page 202

    5 - 53 5. PARAMETERS No. Symbol Name and function Initial value Unit Setting range Control mode Position Speed Torque PD25 For man ufacturer setting 0000h PD26 Do not change th is value by any means. 0000h PD27 0000h PD28 0000h PD29 0000h PD30 0000h 5.4.3 Using forward/reverse rotation stroke en d to change the stopping pattern The stopping pattern ...

  • Mitsumi electronic MR-J3- A - page 203

    5 - 54 5. PARAMETERS MEMO ...

  • Mitsumi electronic MR-J3- A - page 204

    6 - 1 6. DISPLAY AND OPERATION SECTIONS 6. DISPLAY AND OPERATION SECTIONS 6.1 Overview The MR-J3-A servo amplifier has the display section (5-digit, 7-segment LED) and o peration section (4 pushbuttons) for servo amplifier status d isplay, alarm display, parameter setting, e tc. The operation section and display data ar e described below. MO UP DO ...

  • Mitsumi electronic MR-J3- A - page 205

    6 - 2 6. DISPLAY AND OP ERATION SECTIONS 6.2 Display sequence Press the "MODE" button once to shift to the next di s play mode. Refer to section 6.3 and later for the description of the corresponding display mode. To refer to or set the gain filter parame ters, ext ension s etting parameters and I/O setting parame ters, make them valid wi ...

  • Mitsumi electronic MR-J3- A - page 206

    6 - 3 6. DISPLAY AND OP ERATION SECTIONS 6.3 Status display The servo status during operation is shown on the 5-digit, 7-segmen t LED display. Press the "UP" or "DOWN" button to change displa y data as desired. When the required data is selected, the corresponding symbol appears. Press the "SET" b utton to displa y its ...

  • Mitsumi electronic MR-J3- A - page 207

    6 - 4 6. DISPLAY AND OP ERATION SECTIONS 6.3.2 Display examples The following table lis ts display examples. Item Status Displayed data Servo amplifier display Servo motor speed Forward rotation at 2500r/min Reverse rotation at 3000r/min Reverse rotation is indicated by " ". Load inertia moment 15.5 Multiplier ( 1) ABS counter 11252rev 12 ...

  • Mitsumi electronic MR-J3- A - page 208

    6 - 5 6. DISPLAY AND OP ERATION SECTIONS 6.3.3 Status display list POINT Refer to appendix 3 for the measurement point. The following table lis ts the servo statuses tha t may be shown. Name Symbol Unit Description Display range Cumulative feedback pulses C pulse Feedback pulses from the servo motor encoder are counted and displayed. The values in ...

  • Mitsumi electronic MR-J3- A - page 209

    6 - 6 6. DISPLAY AND OP ERATION SECTIONS Name Symbol Unit Description Display range Peak load ratio b The ma ximum current is displayed. The highest value in the past 15 seconds is displayed relative to the rated current of 100 . 0 to 400 Instantaneous torque T Torque that occurred instantaneo usly is displayed. The value of the torque that occurre ...

  • Mitsumi electronic MR-J3- A - page 210

    6 - 7 6. DISPLAY AND OP ERATION SECTIONS 6.4 Diagnostic mode Name Display Description Sequence Not ready. Indicates that the servo amplifier is being initialized or an alarm has occurred. Ready. Indicates that the servo was switched on after completion of initialization and the servo amplifier is ready to operate. External I/O signal display Refer ...

  • Mitsumi electronic MR-J3- A - page 211

    6 - 8 6. DISPLAY AND OP ERATION SECTIONS Name Display Description Servo motor series ID Press the "SET" button to show the series ID of the servo motor currently connected. For indication details, refer to t he Servo Motor Instruction Manual (Vol.2). Servo motor type ID Press the "SET" button to show the type ID of the servo mot ...

  • Mitsumi electronic MR-J3- A - page 212

    6 - 9 6. DISPLAY AND OP ERATION SECTIONS Name Display Description Parameter error No. Indicates no occurrence of parameter error (AL.37) . Indicates that the data of parameter No.PA12 is faulty. Functions at occurrence of an alarm (1) Any mode screen displays the current alarm. (2) Even during alarm occurrence, the oth er screen can be viewed by pr ...

  • Mitsumi electronic MR-J3- A - page 213

    6 - 10 6. DISPLAY AND OP ERATION SECTIONS 6.6 Parameter mode POINT To use the I/O setting parameters, c hange the parameter No.PA19 (parameter write inhibit value. (Refer to section 5.1 .1) The I/O signal settings can be changed us ing the I/O s etting parameter No.PD03 to PD08, PD10 to PD16, PD18. 6.6.1 Parameter mode transition After choosing the ...

  • Mitsumi electronic MR-J3- A - page 214

    6 - 11 6. DISPLAY AND OP ERATION SECTIONS 6.6.2 Operation example (1) Parameters of 5 or less digits The following example shows the opera tion procedur e performed after power-on to change the control mode (Parameter No.PA01) into the spe ed control mo de. Press "MODE" to switch to the basic setting parameter screen. Press four times. Se ...

  • Mitsumi electronic MR-J3- A - page 215

    6 - 12 6. DISPLAY AND OP ERATION SECTIONS (2) Parameters of 6 or more digits The following example give s the operation procedure to change the electronic gear numerator (parameter No.PA06) to "123456". Setting of lower 4 digits The screen flickers. Enter the se tting. Setting of upper 1 digits Press SET once. Press MODE on ce. Press SET ...

  • Mitsumi electronic MR-J3- A - page 216

    6 - 13 6. DISPLAY AND OP ERATION SECTIONS 6.7 External I/O signal display The ON/OFF states of the digital I/O sign als c onnected to the servo amplifier can be confirmed. (1) Operation After power-on, change the displa y mode to t he d iagnostic mode using the "MODE" button . Press UP once. External I/O signal display screen (2) Display ...

  • Mitsumi electronic MR-J3- A - page 217

    6 - 14 6. DISPLAY AND OP ERATION SECTIONS (a) Control modes and I/O signals Connector Pin No. Signal input/output (Note 1) I/ O (Note 2) S ymbols of I/O signals in control m odes Related paramete r P P/S S S/T T T/P CN1 15 I SON SON SON SON SON SON No.PD03 16 I /SP2 SP2 SP2/SP2 SP2 SP2/ No.PD04 17 I PC PC/ST1 ST1 ST1/RS2 RS2 RS2/PC No.PD05 18 I TL ...

  • Mitsumi electronic MR-J3- A - page 218

    6 - 15 6. DISPLAY AND OP ERATION SECTIONS (3) Display data at initial values (a) Position control mode Lit: O N Extinguished: OFF EMG(CN1-42) LOP(C N1-45) TL(CN1-18) PC(CN1-17) Input Output LSP( CN1-43 ) LSN(CN1-44) SON(CN1-15) RES(CN1-19) CR(CN1-41) INP ( CN1-22 ) TLC(CN1-25) ZSP(CN1-23) INP(CN1-24) RD(CN1-49) ALM(CN1-48) OP(CN1-33) (b) Speed cont ...

  • Mitsumi electronic MR-J3- A - page 219

    6 - 16 6. DISPLAY AND OP ERATION SECTIONS 6.8 Output signal (DO) forced output POINT When the servo system is used in a vert ical lift application, turning on the electromagnetic brake interlock (MBR) by the DO forced output after assigning it to connector CN1 will release the electromagnetic brake, causing a drop. Take drop preventive measures on ...

  • Mitsumi electronic MR-J3- A - page 220

    6 - 17 6. DISPLAY AND OP ERATION SECTIONS 6.9 Test operation mode CAUTION The test operation mode is designed to conf irm servo operation. Do not use it for actual operation. If any operational fault has occurred, stop operation u sing the emergency stop (EMG) signal. POINT The test operation mode c annot be used in the absolute position detection ...

  • Mitsumi electronic MR-J3- A - page 221

    6 - 18 6. DISPLAY AND OP ERATION SECTIONS 6.9.2 JOG operation POINT When performing JOG operation, turn ON EMG, LSP and LSN. L SP and LSN can be set to automatic ON by setting parameter No.PD01 to " C ". JOG operation can be performed when there is no command from the external command devic e. (1) Operation The servo motor rotates while h ...

  • Mitsumi electronic MR-J3- A - page 222

    6 - 19 6. DISPLAY AND OP ERATION SECTIONS 6.9.3 Positioning operation POINT MR Configurator is required to perform positioning operation . Turn ON EMG when performing positioning operation. With no command given from the external command device, positioning operation can be executed. (1) Operation a) b) c) d) e) f) g) i) j) k) h) l) m) n) a) Motor ...

  • Mitsumi electronic MR-J3- A - page 223

    6 - 20 6. DISPLAY AND OP ERATION SECTIONS f) Pulse move distance unit selection Select with the option buttons whether the moving distance set in c) is in the com mand pulse unit or in the encoder pulse unit. When the command input pulse unit is selected, the value, which i s the set moving distance multiplied by the electronic gea r ( CMX CDV ), w ...

  • Mitsumi electronic MR-J3- A - page 224

    6 - 21 6. DISPLAY AND OP ERATION SECTIONS (2) Status display The status display can be monitored durin g positioning operation. 6.9.4 Motor-less operation Without connecting the servo motor , you can provide output signals or monitor the status display as if the servo motor is running in response to input device. This oper ation can be used to chec ...

  • Mitsumi electronic MR-J3- A - page 225

    6 - 22 6. DISPLAY AND OP ERATION SECTIONS MEMO ...

  • Mitsumi electronic MR-J3- A - page 226

    7 - 1 7. GENERAL GAIN ADJUSTMENT 7. GENERAL GAIN ADJUSTMENT POINT Consider individual machin e differences, and do not adjust gain too strictly. It is recommended to keep the servo motor torque to 90 or less of the maximum torque of the servo motor during the ope ration. For use in the torque control mode, you need not make gain adj ustment. 7.1 Di ...

  • Mitsumi electronic MR-J3- A - page 227

    7 - 2 7. GENERAL GAIN ADJUSTMEN T (2) Adjustment sequence and mode usage END Inter polatio n made for 2 or more axes? START Operation Auto tuning mode 2 OK? OK? Manual mode OK? No No Yes No Yes No Yes Auto tuning mode 1 Operation Interpolation mode Operation Yes Usage Used when you want to match the position gain (PG1) between 2 or more axes. Norma ...

  • Mitsumi electronic MR-J3- A - page 228

    7 - 3 7. GENERAL GAIN ADJUSTMEN T 7.2 Auto tuning 7.2.1 Auto tuning mode The servo amplifier has a real-time au to tuning functi on which estimates the machine characteristic (load inertia moment ratio) in real time and au tomatically sets the optimum gains according to that value. This function permits ease of gain adjus tment of the servo amplifi ...

  • Mitsumi electronic MR-J3- A - page 229

    7 - 4 7. GENERAL GAIN ADJUSTMEN T 7.2.2 Auto tuning mode basis The block diagram of real-time auto tunin g is shown below. Command Automa tic se tting Loop gains PG1, PG2 , VG2,VIC Current control Curren t fee dback Load inertia momen t Encoder Position/speed feedback Real- time auto tuning section Speed feedback Load inertia momen t ratio estimati ...

  • Mitsumi electronic MR-J3- A - page 230

    7 - 5 7. GENERAL GAIN ADJUSTMEN T 7.2.3 Adjustment procedure by auto tuning Since auto tuning is made valid before s hipment from t he factor y, simply running t he servo motor automa tically sets the optimum gains that match the machine. Mere ly changing the response leve l setting value as required completes the adjustment. The adjustme nt proced ...

  • Mitsumi electronic MR-J3- A - page 231

    7 - 6 7. GENERAL GAIN ADJUSTMEN T 7.2.4 Response level setting in auto tuning mode Set the response (The first digit o f parameter No.PA0 9) of the whole servo system. As the response leve l setting is increased, the track ability and settling time for a command decreases, but a too high response level will generate vibration. Hence, make setting u ...

  • Mitsumi electronic MR-J3- A - page 232

    7 - 7 7. GENERAL GAIN ADJUSTMEN T 7.3 Manual mode 1 (simple manual adju stment) If you are not satisfied with the adjustment of auto tuning, you can make simple manual adjustment with three parameters. POINT If machine resonance occurs, adaptive t uning mode (parameter No.PB01) or machine resonance suppressi on filter (parameter No. PB13 to PB16) m ...

  • Mitsumi electronic MR-J3- A - page 233

    7 - 8 7. GENERAL GAIN ADJUSTMEN T 2) Speed integral compensation (VIC: pa rameter No.PB10) To eliminate stationary deviation against a comm and, the speed control loop is under proportion al integral control. For the speed in tegr al compensation, set the time cons tant of this integral control. Increasing the setting lowers the response level. How ...

  • Mitsumi electronic MR-J3- A - page 234

    7 - 9 7. GENERAL GAIN ADJUSTMEN T (c) Adjustment description 1) Model loop gain (parameter No.PB07) This parameter determines the response level of the model loop. Increasing positio n loop gain 1 improves track ability to a position command but a too high value will make overshooting liab le to occur at the time of settling. Model loop gain guidel ...

  • Mitsumi electronic MR-J3- A - page 235

    7 - 10 7. GENERAL GAIN ADJUSTMEN T 7.4 Interpolation mode The interpolation mode is u sed to match the position lo op gains of th e axes when performing th e interpolation operation of servo motors of two or more axes for an X- Y table or the like. In this mode, manua lly set the model loop gain that determines c ommand track ability. Other par ame ...

  • Mitsumi electronic MR-J3- A - page 236

    7 - 11 7. GENERAL GAIN ADJUSTMEN T 7.5 Differences between MELSERVO-J2-Supe r and MELSERVO-J3 in auto tuning To meet higher response demands, the MELSERVO-J 3 series has been changed in response level setting range from the MELSERVO-J2-Super series . The following table lis ts comparison of the respon se level setting. MELSERVO-J2-Super MELSERVO-J3 ...

  • Mitsumi electronic MR-J3- A - page 237

    7 - 12 7. GENERAL GAIN ADJUSTMEN T MEMO ...

  • Mitsumi electronic MR-J3- A - page 238

    8 - 1 8. SPECIAL ADJUSTMENT FUNCTI ONS 8. SPECIAL ADJUSTMENT FUNCTIONS POINT The functions given in this chapter n eed not be used gene rally. Use them if you are not satisfied with the machine statu s after making adjustment in the methods in chapter 7. If a mechanical system has a natural resonance point, increasing the servo syste m response lev ...

  • Mitsumi electronic MR-J3- A - page 239

    8 - 2 8. SPECIAL ADJUSTMENT FUNCTIONS POINT The machine resonan ce frequency which adaptive filter (adaptive tuning) can respond to is about 100 to 2.25kHz. Ada ptive vibration suppression control ha s no effect on the resonance freque ncy outside this range. Adaptive vibration suppression cont rol may provide no effect on a mechanical system which ...

  • Mitsumi electronic MR-J3- A - page 240

    8 - 3 8. SPECIAL ADJUSTMENT FUNCTIONS (3) Adaptive tuning procedure The response has increased to the machine limit. The machin e is too complicat ed to provide the optimum filter. Factor Adap tive t unin g Operation Is the target resp o nse reached? Tuning ends automatically after the predetermined period of time. (Para meter No.PB 01 turn s to &q ...

  • Mitsumi electronic MR-J3- A - page 241

    8 - 4 8. SPECIAL ADJUSTMENT FUNCTIONS POINT "Filter OFF" enables a return to the initial value. When adaptive tuning is execute d, vibration sound increase s as an excitation signal is forcibly applied for several second s. When adaptive tuning is executed, mach ine resonance is detected for a maximum of 10 seconds and a filter is g enera ...

  • Mitsumi electronic MR-J3- A - page 242

    8 - 5 8. SPECIAL ADJUSTMENT FUNCTIONS (2) Parameters (a) Machine resonance suppression filter 1 (parameter No.PB13, PB14) Set the notch frequency, notch dep th and notch width o f the machine resonance suppression filter 1 (parameter No.PB13, PB14) When the "manual mode" is selected in the adaptive tuni ng mode (parameter No.PB01), the se ...

  • Mitsumi electronic MR-J3- A - page 243

    8 - 6 8. SPECIAL ADJUSTMENT FUNCTIONS 8.4 Advanced vibration suppression cont rol (1) Operation Vibration suppression control is used to further suppr ess machine side vibration, such as workpiece end vibration and base shake. The motor sid e operation is adjusted for positioning so that the machine does not shake. Vibra tion sup pres sion co ntrol ...

  • Mitsumi electronic MR-J3- A - page 244

    8 - 7 8. SPECIAL ADJUSTMENT FUNCTIONS POINT The function is made valid when the auto tuning mo de (parameter No.PA08) is the auto tuning mode 2 ("0002") or man ual mode ("0003"). The machine resonan c e frequency support ed in the vi bration suppression contro l tuning mode is 1.0 to 100.0Hz. The functi on is not effective for v ...

  • Mitsumi electronic MR-J3- A - page 245

    8 - 8 8. SPECIAL ADJUSTMENT FUNCTIONS (3) Vibration suppression control tuning pr ocedure No Estimation cannot be made as machine side vibration has not been transmitted to the motor side . The response of the model loop gain has increased to the machine side vibration frequency (vibration suppression control limit) . Vibra tion s uppres sion co nt ...

  • Mitsumi electronic MR-J3- A - page 246

    8 - 9 8. SPECIAL ADJUSTMENT FUNCTIONS (4) Vibration suppression control manual mode Measure work side vibration and device shake with the machine an alyzer or external measuring instrumen t, and set the vibration suppression control vibratio n freq uency (parameter No.PB19) and vibration suppression control resonance frequency (parameter No.PB20) t ...

  • Mitsumi electronic MR-J3- A - page 247

    8 - 10 8. SPECIAL ADJUSTMENT FUNCTIONS POINT When machine side vibration doe s not show up in motor side vibration, the setting of the motor side vibration fr equency does n ot produce an effect. When the anti-reso nance frequency and reson ance frequency can be confi r med using the machine analyze r or external measuring instrument, do not set th ...

  • Mitsumi electronic MR-J3- A - page 248

    8 - 11 8. SPECIAL ADJUSTMENT FUNCTIONS 8.6.2 Function block diagram The valid loop gains PG2, VG2, VIC, GD2, VRF1 and VRF2 of the actual loop are c hanged according to the conditions selected by gain changing selection CDP (p arameter No.PB26) and gain changing con dition CDL (parameter No.PB27). Comparator Changi ng CDP Parameter No.PB26 Valid GD2 ...

  • Mitsumi electronic MR-J3- A - page 249

    8 - 12 8. SPECIAL ADJUSTMENT FUNCTIONS 8.6.3 Parameters When using the gain changing function, always set parameter No.PA08 to " 3" (auto tuning mode) to select the manual mode in the auto tuning modes. Th e gain changing func tion cannot be used in the auto tuning mode. Parameter No. Abbrevi- ation Name Unit Description PB06 GD2 Ratio of ...

  • Mitsumi electronic MR-J3- A - page 250

    8 - 13 8. SPECIAL ADJUSTMENT FUNCTIONS (4) Gain changing selection (parameter No.PB26) Used to set the gain changing condition. Choose the changing condition in the first digit and second digit. If "1" is set in the first d igit, the gain can be changed by the gain changing (CDP) in put device. The gain changing (CDP) can be assigned to t ...

  • Mitsumi electronic MR-J3- A - page 251

    8 - 14 8. SPECIAL ADJUSTMENT FUNCTIONS 8.6.4 Gain changing procedure This operation will be described by way of setting examples. (1) When you choose changing by input device (CDP) (a) Setting Parameter No. Abbreviation Name Setting Unit PB06 GD2 Ratio of load inertia moment to servo motor inertia moment 4.0 Multiplier ( 1) PB07 PG1 Model loop gain ...

  • Mitsumi electronic MR-J3- A - page 252

    8 - 15 8. SPECIAL ADJUSTMENT FUNCTIONS (2) When you choose changing by droop pulses In this case, gain changing vibrati on suppression control cannot be used. (a) Setting Parameter No. Abbreviation Name Setting Unit PB06 GD2 Ratio of load ine rtia moment to s ervo motor inertia mo ment 4.0 Multiplier ( 1) PB07 PG1 Mo del lo op ga in 100 rad/s PB08 ...

  • Mitsumi electronic MR-J3- A - page 253

    8 - 16 8. SPECIAL ADJUSTMENT FUNCTIONS 8.7 Vibration suppression control filter 2 POINT By using the advanced vibration sup pression control and the vibration suppression control filter 2, the machi ne side vibration of two frequencies can be suppress ed. The frequency range of machine vibratio n, which can be supported by the vibration suppression ...

  • Mitsumi electronic MR-J3- A - page 254

    8 - 17 8. SPECIAL ADJUSTMENT FUNCTIONS (2) Parameter Set parameter No.PB45 (vibration suppression contro l filter 2) as shown below. For the vibration suppression control filter 2, set a frequency close to the vibration fre quency [Hz] at the machine side. 1.2dB E Vibrat ion su ppression filt er 2 setting f requen cy selection Frequency [Hz] 00 01 ...

  • Mitsumi electronic MR-J3- A - page 255

    8 - 18 8. SPECIAL ADJUSTMENT FUNCTIONS MEMO ...

  • Mitsumi electronic MR-J3- A - page 256

    9 - 1 9. TROUBLESHOOTING 9. TROUBLESHOOTING POINT As soon as an alarm occurs, turn off Servo-on (SON) and power off. Refer to section 15.6 for th e servo amplifiers of 30k to 55kW. If an alarm/warning has occurred, refer to se ction 9.1 to 9.3 and remove its cause. In case of a trouble without an alarm/warning, refer to section 9.4 and remove its c ...

  • Mitsumi electronic MR-J3- A - page 257

    9 - 2 9. TROUBLESHOOTING 9.2 Remedies for alarms CAUTION When any alarm has occurred, eliminate i t s cause, ensure safety, then reset the alarm, and restart operation. Otherwise, injury ma y occur. If an absolute position erase (AL .25) occurred, always to make home position setting again. Not doing so may cause unexpected ope ration. As soon as a ...

  • Mitsumi electronic MR-J3- A - page 258

    9 - 3 9. TROUBLESHOOTING Display Name Definition Cause Action (Note 2) Alarm details AL.10 Undervoltage Power supply voltage dropped. 1. Power supply voltage is low. <Checking method> Check that the power supply voltage is the following voltage or more. MR-J3- A: 160VAC MR-J3- A1: 83VAC MR-J3- A4: 280VAC Check the power supply. 2 2. Shortage ...

  • Mitsumi electronic MR-J3- A - page 259

    9 - 4 9. TROUBLESHOOTING Display Name Definition Cause Action (Note 2) Alarm details AL.16 Encoder error 1 (At power on) Communication error occurred between encoder and servo amplifier. 1. Encoder connector (CN2) disconnected. Connect correctly. 44 2. Encoder cable type (2-wire, 4-wire) selection was incorrect in parameter setting. Correct the set ...

  • Mitsumi electronic MR-J3- A - page 260

    9 - 5 9. TROUBLESHOOTING Display Name Definition Cause Action (Note 2) Alarm details AL.20 Encoder error 2 (during runtime) Communication error occurred between encoder and servo amplifier. 1. Encoder cable disconnected. <Checking method> Check the connection of the encoder cable. Connect the servo motor encoder connector to the servo amplifi ...

  • Mitsumi electronic MR-J3- A - page 261

    9 - 6 9. TROUBLESHOOTING Display Name Definition Cause Action (Note 2) Alarm details AL.24 Main circuit error Ground fault occurred in servo motor power (U, V, W). 1. Power input wires and servo motor power wires are in contact. (A power input cable and a servo motor power cable are in contact at the main circuit terminal block (TE1).) Modify the w ...

  • Mitsumi electronic MR-J3- A - page 262

    9 - 7 9. TROUBLESHOOTING Display Name Definition Cause Action (Note 2) Alarm details AL.25 Absolute position erase Absolute position data is erased. 1. Voltage drop in encoder. (Battery disconnected.) After leaving the alarm occurring for a few minutes, switch power off, then on again. Always make home position setting again. 2. Battery voltage low ...

  • Mitsumi electronic MR-J3- A - page 263

    9 - 8 9. TROUBLESHOOTING Display Name Definition Cause Action (Note 2) Alarm details AL.31 Overspeed Speed has exceeded the instantaneous permissible speed. 1. Input command pulse frequeroy is too high. Set command pulse frequency correctly. 2. Small acceleration/deceleration time constant caused overshoot to be large. Increase acceleration/ decele ...

  • Mitsumi electronic MR-J3- A - page 264

    9 - 9 9. TROUBLESHOOTING Display Name Definition Cause Action (Note 2) Alarm details AL.33 Overvoltage Bus voltage exceeded to following voltage. MR-J3- A(1): 400VDC or more MR-J3- A4: 800VDC or more 1. Regenerative option is not used. Use the regener ative option. 2. Though the regenerative option is used, the parameter No.PA02 setting is " 0 ...

  • Mitsumi electronic MR-J3- A - page 265

    9 - 10 9. TROUBLESHOOTING Display Name Definition Cause Action (Note 2) Alarm details AL.45 Main circuit device overheat Main circuit device overheat 1. Ambient temperature of servo amplifier is over 55 (131 ). Check environment so that ambient temperature is 0 to 55 (32 to 131 ). 2. Used beyond the specifications of close mounting. Use within the ...

  • Mitsumi electronic MR-J3- A - page 266

    9 - 11 9. TROUBLESHOOTING Display Name Definition Cause Action (Note 2) Alarm details AL.50 Overload 1 Load exceeded overload protection characteristic of servo amplifier. 1. Servo amplifier is used in excess of its continuous output current. 1. Reduce load. 2. Check operation pattern. 3. Check that the electromagnetic brake is not applied. 4. Chec ...

  • Mitsumi electronic MR-J3- A - page 267

    9 - 12 9. TROUBLESHOOTING Display Name Definition Cause Action (Note 2) Alarm details AL.51 Overload 2 Machine collision or the like caused a continuous maximum current for a few seconds. 1. Servo amplifier fault. <Checking method> The servo motor is disconnected on the machine side and then the servo motor is test-operated. The alarm (AL.51) ...

  • Mitsumi electronic MR-J3- A - page 268

    9 - 13 9. TROUBLESHOOTING Display Name Definition Cause Action (Note 2) Alarm details AL.52 Error excessive The difference between the model position and the actual servo motor position exceeds three rotations. (Refer to the function block diagram in section 1.2.) 1. Acceleration/deceleration time constant is too small. Increase the acceleration/ d ...

  • Mitsumi electronic MR-J3- A - page 269

    9 - 14 9. TROUBLESHOOTING Display Name Definition Cause Action (Note 2) Alarm details (Note 1) 88888 Watchdog CPU, parts fault y 1. Fault of parts in servo amplifier <Checking method> Alarm (88888) oc curs if power is switched on after disconnection o f all cables but the c ontrol ci rcuit power supply cable. Change the servo amplifier. 2. Th ...

  • Mitsumi electronic MR-J3- A - page 270

    9 - 15 9. TROUBLESHOOTING 9.3 Remedies for warnings CAUTION If an absolute position counter warning (AL.E3) occurred, always to make home position setting again. Not d oing so may cause unexpected operation . POINT When any of the following alarms has occurred, do not resume operation b y switching power of the servo amplifier OFF/ON repeatedly. Th ...

  • Mitsumi electronic MR-J3- A - page 271

    9 - 16 9. TROUBLESHOOTING Display Name Definition Cause Action AL.E1 Overload warning 1 There is a possibility that overload alarm 1 or 2 may occur. Load increased to 85% or more of overload alarm 1 or 2 occurrence level. Refer to AL.50, AL.51. AL.E3 Absolute position counter warning Absolute position encoder pulses faulty. 1. Noise entered the enc ...

  • Mitsumi electronic MR-J3- A - page 272

    9 - 17 9. TROUBLESHOOTING 9.4 Troubles without an alarm/warning POINT Even if a servo amplifier, a servo moto r, or an encoder malfunctions, the following phenomena may occur. The following shows the ex amples of the estimated caus es of the troubles without alarms/warnings. Refer to this chapter and remove th eir causes. Phenomena Checkpoint Es ti ...

  • Mitsumi electronic MR-J3- A - page 273

    9 - 18 9. TROUBLESHOOTING Phenomena Checkpoint Es timated cause Action The servo motor does not operate. Check the cumulative command pulses with the status display or MR Configurator. The display does not change even if the pulse train command is input. The wiring of the command pulse train signal is incorrect. Check the type of the command pulse ...

  • Mitsumi electronic MR-J3- A - page 274

    9 - 19 9. TROUBLESHOOTING Phenomena Checkpoint Es timated cause Action The servo motor speed is not accelerated. Or too fast. Check the settings of the speed command, the speed limit and the electronic gear. The setting of the speed command, the speed limit or the electronic gear is incorrect. Review the settings of the speed command, the speed lim ...

  • Mitsumi electronic MR-J3- A - page 275

    9 - 20 9. TROUBLESHOOTING Phenomena Checkpoint Es timated cause Action Unusual noise is generated from the servo amplifier. 1. If the safe operation is possible, repeat acceleration/deceleration 4 times or more to complete the auto tuning. 2. Reduce the auto tuning response (parameter No.PA09). 1. The servo gain is high. 2. The auto tuning response ...

  • Mitsumi electronic MR-J3- A - page 276

    9 - 21 9. TROUBLESHOOTING Phenomena Checkpoint Es timated cause Action The servo motor vibrates. Check the mounting accuracy of the servo motor and the machine. The eccentricity is big by the core gaps. Review the direct connection accuracy. Check the axial e nd load on the servo motor. The axial end load on the servo motor is large. Adjust the axi ...

  • Mitsumi electronic MR-J3- A - page 277

    9 - 22 9. TROUBLESHOOTING Phenomena Checkpoint Es timated cause Action The servo motor starts immediately when the servo amplifier power supply is turned on/The servo motor starts immediately when servo-on is executed. Check that the servo-on (SON) is not on. 1. Check with the external I/O signal display in the diagnostic mode. 2. Check with the &q ...

  • Mitsumi electronic MR-J3- A - page 278

    9 - 23 9. TROUBLESHOOTING Phenomena Checkpoint Es timated cause Action The position is misaligned in operation after the home position return. Check the servo alarm/warning. 1. A servo alarm is occurring. 2. The servo motor coasts due to a servo alarm. Check the details of the alarm and remove its cause. The output pulse counter and the servo ampli ...

  • Mitsumi electronic MR-J3- A - page 279

    9 - 24 9. TROUBLESHOOTING Phenomena Checkpoint Es timated cause Action The absolute position reconstruction position is misaligned at recovery by the absolute position detection system. Check the settings as follows for the geared servo motor. 1. The travel distance per servo motor revolution (Set with the controller.) 2. Command input pulses per r ...

  • Mitsumi electronic MR-J3- A - page 280

    9 - 25 9. TROUBLESHOOTING Phenomena Checkpoint Es timated cause Action An abnormal value is displayed on the monitor value on MR Configurator. Check that the model selection is set correctly. Check with the "System settings" command on the "Setup" menu. The other model, which differs from the one connected on the model selection ...

  • Mitsumi electronic MR-J3- A - page 281

    9 - 26 9. TROUBLESHOOTING MEMO ...

  • Mitsumi electronic MR-J3- A - page 282

    10 - 1 10. OUTLINE DRAWINGS 10. OUTLINE DRAWINGS 10.1 Servo amplifier (1) MR-J3-10A MR-J3-20A MR-J3-10A1 MR-J3-20A1 [Unit: mm] 135 Approx.80 6 Approx.14 Appro x . 25.5 CNP3 CNP2 CNP1 Approx.68 With MR-J3BAT CN5 CN6 CN3 CN1 CN2 CN2L CN4 L1 L2 L3 N P1 P2 P CD L 1 1L21 U V W CHARGE L1 L2 L3 N P1 P2 P C D L11 L21 U V W 6 mounting hol e 4 168 40 6 156 6 ...

  • Mitsumi electronic MR-J3- A - page 283

    10 - 2 10. OUTL INE DRAWINGS (2) MR-J3-40A MR-J3-60A MR-J3-40A1 [Unit: mm] 170 6 Approx.14 Approx. 25.5 5 Approx.68 With MR-J3BAT CN5 CN6 CN3 CN1 CN2 CN2L CN4 L1 L2 L3 N P1 P2 P C D L11 L21 U V W CHARGE CNP1 L1 L2 L3 N P1 P2 P C D L11 L21 U V W CNP2 CNP3 156 6 6 161 168 6 6 mounting hole Approx.8 0 (Note) (Note) Note. This da ta applies to the 3-ph ...

  • Mitsumi electronic MR-J3- A - page 284

    10 - 3 10. OUTL INE DRAWINGS (3) MR-J3-70A MR-J3-100A [Unit: mm] Approx.8 0 185 6 60 12 CNP3 CNP2 CNP1 6 Approx.68 With MR-J3BAT CN5 CN6 CN3 CN1 CN2 CN 2L CN4 L1 L2 L3 N P1 P2 P C D L11 L2 1UV W CHARGE 12 42 L1 L2 L3 N P1 P2 P C D L11 L21 U V W 156 6 6 Approx.14 168 161 6 mounting hole Approx. 25.5 Cooling fan air in take Cooli ng fa n Cooling fan ...

  • Mitsumi electronic MR-J3- A - page 285

    10 - 4 10. OUTL INE DRAWINGS (4) MR-J3-60A4 MR-J3-100A4 [Unit: mm] 6 12 42 CNP2 CNP3 CNP1 60 12 195 6 Approx. 25.5 Approx.68 With MR-J3BAT Approx.80 6 mounting hole Mass: 1.7 [kg] (3.75 [lb]) U V W CNP3 P C D L 11 L 21 CNP2 L 1 L 2 L 3 N P 1 P 2 CNP1 Screw size: M4 Tightening torque: 1.2 [N m] (10.6 [lb in]) Terminal signal layout PE termi nal Appr ...

  • Mitsumi electronic MR-J3- A - page 286

    10 - 5 10. OUTL INE DRAWINGS (5) MR-J3-200A(4) POINT Connectors (CNP1, CNP2, and CNP3) and appeara nce of MR-J3-200A servo amplifier have been changed from April 2008 production. Model name of the servo amplifier before March 20 08 is changed to MR-J3-200A-RT. For M R -J3- 200A-RT, refer to appendix 5. [Unit: mm] CNP2 CNP3 CNP1 195 6 6 78 6 45 90 C ...

  • Mitsumi electronic MR-J3- A - page 287

    10 - 6 10. OUTL INE DRAWINGS (6) MR-J3-350A [Unit: mm] Approx.14 6 21.4 Approx.68 6 6 45 6 mounting hole Approx.80 195 168 78 6 156 6 6 90 85 With MR-J3BAT Approx. 25.5 Cooling fan air int ake Cooling fan Cooling f an Exhaust Mass: 2.1 [kg] (4.63 [lb]) U V W CNP3 P C D L 11 L 21 CNP2 L 1 L 2 L 3 N P 1 P 2 CNP1 Terminal signal layout PE terminal Scr ...

  • Mitsumi electronic MR-J3- A - page 288

    10 - 7 10. OUTL INE DRAWINGS (7) MR-J3-350A4 MR-J3-500A (4) [Unit: mm] CN4 CN2L CN2 CN1 CN3 CN6 CN5 CN4 CN2L CN2 CN1 CN3 CN6 CN5 CHARGE 130 118 6 250 235 6 With MR-J3BAT 2- 6 mounti ng ho le 200 Approx.80 131.5 68.5 Cooling fan exhaust 6 Termin al layout (Terminal cover op en) TE1 TE2 TE3 20.5 3 places for grou nd (M4) CAUTION WARNING CAUTION WARNI ...

  • Mitsumi electronic MR-J3- A - page 289

    10 - 8 10. OUTL INE DRAWINGS (8) MR-J3-700A (4) [Unit: mm] 172 160 6 300 285 6 With MR-J3BAT 200 138 62 6 TE2 TE3 TE1 CN2 CN1 CN3 CN6 CN5 CN4 CN2L CN2 CN1 CN3 CN6 CN5 CN4 CN2L CHARGE Regenerative resistor lead termi nal fi xing screw 20.5 2- 6 mounting hole Terminal layout (Terminal co ver open) Cooling fan exha ust CAUTION WARNING CAUTION WARNING ...

  • Mitsumi electronic MR-J3- A - page 290

    10 - 9 10. OUTL INE DRAWINGS (9) MR-J3-11KA(4) to MR-J3-22KA(4) [Unit: mm] 12 236 12 260 12 260 Approx.80 With MR-J3BAT Rating plate 2- 12 mounting hole TE 183 227 CN1 26 52 6 x 26 = 156 123 13 Servo amplifier MR-J3-11KA(4) 18.0 (40) MR-J3-15KA(4) 18.0 (40) MR-J3-22KA(4) 19.0 (42) Mass[kg]([lb]) Air intake Cooling fan exhaust 236 0.5 Approx. 260 4- ...

  • Mitsumi electronic MR-J3- A - page 291

    10 - 10 10. OUTL INE DRAWINGS 10.2 Connector (1) Miniature delta ribbon ( MDR) system (3M) (a) One-touch lock type [Unit: mm] E B A 23.8 39.0 12.7 C Logo etc, are indicated here. D Connector Shell kit Each t ype of dimension A B C D E 10150-3000PE 10350-52F0-008 41.1 52.4 18.0 14.0 17.0 (b) Jack screw M2.6 type This is not available as option. [Uni ...

  • Mitsumi electronic MR-J3- A - page 292

    10 - 11 10. OUTL INE DRAWINGS (2) SCR connector system (3M) Receptacle: 36210-0100PL Shell kit : 36310-3200-008 [Unit: mm] 34.8 39.5 22.4 11.0 ...

  • Mitsumi electronic MR-J3- A - page 293

    10 - 12 10. OUTL INE DRAWINGS MEMO ...

  • Mitsumi electronic MR-J3- A - page 294

    11 - 1 11. CHARACTERISTICS 11. CHARACTERISTICS 11.1 Overload protection characteristi cs An electronic thermal relay is built in the servo amplif ier to protect the servo motor, servo amplifier and servo motor power line from overloads. Over load 1 a larm (AL.50) occurs if ov erload opera tion performed is above the electronic thermal relay protect ...

  • Mitsumi electronic MR-J3- A - page 295

    11 - 2 11. CHARACTERISTIC S 10000 1000 100 10 1 0 In oper ation In servo lock O p e r a t i o n t i m e [ s ] (Note 1) Load r atio [ ] 50 100 150 200 250 300 MR-J3-11KA(4) to MR-J3-22KA(4) Note 1. If operation that generate s torque more than 100 of the rating is performed with an abnormally high frequency in a servo motor stop status (servo lock s ...

  • Mitsumi electronic MR-J3- A - page 296

    11 - 3 11. CHARACTERISTIC S 11.2 Power supply equipment capacity and gene rated loss (1) Amount of heat generated by the servo amplifier Table 11.1 indicates servo amplifiers' power supply capacities and losses generated under rate d load. For thermal design of an enclosure, use the values in Table 11.1 in consideration for th e worst operatin ...

  • Mitsumi electronic MR-J3- A - page 297

    11 - 4 11. CHARACTERISTIC S Servo amplifier Servo motor (Note 1) Power supply capacity [kVA] (Note 2) Servo amplifier-generated heat [W] Area required for heat dissipation [m 2 ] At rated torque With servo off MR-J3-500A(4) HF-SP502(4) 7.5 195 25 3.9 HC-RP353 5.5 135 25 2.7 HC-RP503 7.5 195 25 3.9 HC-UP352 5.5 195 25 3.9 HC-UP502 7.5 195 25 3.9 HC- ...

  • Mitsumi electronic MR-J3- A - page 298

    11 - 5 11. CHARACTERISTIC S (2) Heat dissipation area for enclosed servo amp lifier The enclosed control box (hereafter called the control box) which will con tain the servo amplifier should be designed to ensure that its temperature rise is within 10 at the ambient temperature of 40 . (With a 5 (41 ) safety margin, the system should operate within ...

  • Mitsumi electronic MR-J3- A - page 299

    11 - 6 11. CHARACTERISTIC S 11.3 Dynamic brake characteristics POINT Dynamic brake operates at occurrence of alarm, se rv o emergency st op warning (AL.E6) and when power is turned off. Do not use dynamic brake to stop in a normal operation as it is the function to stop in em ergency. Maximum usage time of dynamic bra ke for a machine operating und ...

  • Mitsumi electronic MR-J3- A - page 300

    11 - 7 11. CHARACTERISTIC S (2) Dynamic brake time constant The following shows necessary dynamic brake time constant for the equations (11.2). (a) 200V class servo motor Speed [r/min] 0 0 1000 200 0 5 10 15 20 25 3000 4000 5000 6000 43 053 13 23 73 Time constant [ms] 0 0 1000 2000 5 10 15 20 25 3000 4000 5000 6000 43 053 13 23 73 Speed [ r/min ] T ...

  • Mitsumi electronic MR-J3- A - page 301

    11 - 8 11. CHARACTERISTIC S 0 0 500 1000 15 00 2000 80 60 40 20 11K2 15K2 22K2 502 702 Ti m e c o n s t a n t [ m s ] Speed [r/min] Ti m e c o n s t a n t [ m s ] 0 0 52 500 1000 150 0 2000 202 200 152 102 160 120 80 40 302 Speed [r/mi n] HA-LP2000r/min se ries HC-LP series 80 0 70 60 50 40 30 20 10 500 1 000 150 0 2000 2 500 300 0 0 15K1M 11K1M Ti ...

  • Mitsumi electronic MR-J3- A - page 302

    11 - 9 11. CHARACTERISTIC S (b) 400V class servo motor 5024 0 1000 2000 3000 75 60 45 30 15 0 90 7024 1524 3524 1024 524 2024 Ti m e c o n s t a n t [ m s ] Speed [r/min] Ti m e c o n s t a n t [ m s ] 0 400 800 1200 35 0 30 25 20 15 10 5 8014 15 K14 12K14 20K1 4 6014 Speed [r/min] HA-SP2000r/min serie s HA-LP1000r/min se ries Ti m e c o n s t a n ...

  • Mitsumi electronic MR-J3- A - page 303

    11 - 10 11. CHARACTERISTIC S 11.3.2 The dynamic brake at the load in ertia moment Use the dynamic brake under the load inertia moment rati o indicated in the following table . If the load inertia moment is higher than this value, the d ynamic brake may burn. If the re is a possibility that the lo ad inertia moment may exceed the value, contact your ...

  • Mitsumi electronic MR-J3- A - page 304

    11 - 11 11. CHARACTERISTIC S 11.4 Cable flexing life The flexing life of the cables is shown below. This graph calculated values. Since they are not g uaranteed values, provide a little allow ance for these values. 1 10 7 5 10 7 1 10 8 5 10 6 1 10 6 5 10 5 1 10 5 5 10 4 1 10 4 5 10 3 1 10 3 a b F l e x i n g l i f e [ t i m e s ] 4 7 10 20 40 70 10 ...

  • Mitsumi electronic MR-J3- A - page 305

    11 - 12 11. CHARACTERISTIC S MEMO ...

  • Mitsumi electronic MR-J3- A - page 306

    12 - 1 12. OPTIONS AND AUXILIARY EQUIPMENT 12. OPTIONS AND AU XILIARY EQUIPMENT WARNING Before connecting any option or peripheral equipmen t, turn off the power and wait for 15 minutes or longer until the charge lamp turns off. Then, confirm that the voltage between P( ) and N( ) is safe with a voltage tester and o thers. Otherwise, an electric sh ...

  • Mitsumi electronic MR-J3- A - page 307

    12 - 2 12. OPTIONS AND AUXILI ARY EQUIPMENT 12.1.1 Combinations of cable/co nnector sets Servo ampl ifier Controller Operation panel To CN6 To CN1 To CN2 Personal comput er CN5 CN3 CN1 CN2 4) 7) 1) 2) 3) 5) 6) CN6 CNP1 CNP2 CNP3 (Note 1 ) 37) CN4 Direct connection type (ca ble length 10m or le ss, IP65) Battery MR-J3BAT 20)21)22 )23) 36) Servo mot ...

  • Mitsumi electronic MR-J3- A - page 308

    12 - 3 12. OPTIONS AND AUXILI ARY EQUIPMENT Servo mot or HF-JP11K1M(4) 15K1 M(4) Power supply connec tor Brake connect or Encoder connec tor From previous page a) Servo mot or HC-RP HC-UP HC-LP Terminal box Servo mot or HA-LP 38) 35)39 )40) From previous p age b) Power supply connec tor Brake connector Encoder connector Power supply connec tor Brak ...

  • Mitsumi electronic MR-J3- A - page 309

    12 - 4 12. OPTIONS AND AUXILI ARY EQUIPMENT No. Product Model Description Application 1) Servo amplifier power supply connector Supplied with servo amplifiers of 1kW or less in 100V class and 200V class CNP1 connector: 54928-0670 (Molex) CNP2 connector: 54927-0520 (Molex) CNP3 connector: 54928-0370 (Molex) <Applicable cable example> Wire size ...

  • Mitsumi electronic MR-J3- A - page 310

    12 - 5 12. OPTIONS AND AUXILI ARY EQUIPMENT No. Product Model Description Application 6) USB cable MR-J3USBCBL3M Cable length: 3m For CN5 connector minB connector (5 pins) For personal computer connector A connector For connection with PC-AT compatible personal computer 7) Monitoring cable MR-J3CN6CBL1M Cable length: 1m 3 (Red) 2 (White ) 1 (Black) ...

  • Mitsumi electronic MR-J3- A - page 311

    12 - 6 12. OPTIONS AND AUXILI ARY EQUIPMENT No. Product Model Description Application 18) Motor brake cable MR-BKS2CBL03M-A1-L Cable length: 0.3m Brake c onnec tor HF-MP series HF-KP series Refer to section 12.1.4 for details. IP55 Load side lead 19) Motor brake cable MR-BKS2CBL03M-A2-L Cable length: 0.3m Brake conn ector HF-MP series HF-KP series ...

  • Mitsumi electronic MR-J3- A - page 312

    12 - 7 12. OPTIONS AND AUXILI ARY EQUIPMENT No. Product Model Description Application 29) Encoder cable MR-J3ENSCBL M-L Cable length: 2 5 10 20 30m For HF-SP HC-U P HC-LP HC-RP HA-LP series HF-JP53(4) to 503(4) Refer to section 12.1.2 (5) for details. IP67 Standard flex life 30) Encoder cable MR-J3ENSCBL M-H Cable length: 2 5 10 20 30 40 50m IP67 L ...

  • Mitsumi electronic MR-J3- A - page 313

    12 - 8 12. OPTIONS AND AUXILI ARY EQUIPMENT No. Product Model Description Application 38) Brake connector set MR-BKCN Plug: D/MS3106A10SL-4S(D190) (DDK) For cable connector: YSO10-5-8( Daiwa Dengyo) Example of applicable cable Applicable wire size: 0.3 to 25mm 2 (AWG22 to AWG16) Cable finish: 5 to 8.3mm For HA-LP For HC-UP For HC-LP For HF- JP11K1M ...

  • Mitsumi electronic MR-J3- A - page 314

    12 - 9 12. OPTIONS AND AUXILI ARY EQUIPMENT No. Product Model Description Application 47) Brake connector set MR-BKCNS1-S06 Straight plug: CM10-SP2S-VP-L Socket contact: CM10-#22SC (S2) (D8)-10 0 (DDK) For HF-SP series HF-JP53(4) to 503(4) IP67 (Note) 48) Brake connector set MR-BKCNS1A-S06 Angle plug: CM10-AP2S-VP-L Socket contact: CM10-#22SC (S2) ...

  • Mitsumi electronic MR-J3- A - page 315

    12 - 10 12. OPTIONS AND AUXILI ARY EQUIPMENT 12.1.2 Encoder cable/connecto r sets (1) MR-J3ENCBL M-A1-L/H MR-J3ENCBL M-A2-L/H These cables are encoder cables for the HF-MP HF-KP series servo motors. The numerals in the Cable Length field of the table are the s ymbols entered in the part o f the cable model. The cables of th e lengths with the symbo ...

  • Mitsumi electronic MR-J3- A - page 316

    12 - 11 12. OPTIONS AND AUXILI ARY EQUIPMENT (b) Cable internal wiring dia gram Servo amplifier side connector Enco der si de connector Plate MR-J3 ENCBL2M -L/-H MR-J3 ENCBL5M -L/-H MR-J3ENCBL10M-L/-H P5 LG 1 2 MR MRR 3 4 2 3 9 SD 5 4 6 9 LG MR MRR SHD P5 BAT BAT (2) MR-EKCBL M-L/H POINT The following encoder cables are of f our-wire type. When usi ...

  • Mitsumi electronic MR-J3- A - page 317

    12 - 12 12. OPTIONS AND AUXILI ARY EQUIPMENT (a) Connection of servo amplifier and servo motor Servo motor HF-MP HF-KP 1) MR-EKCBL M-L MR-EKCBL M-H MR- J3JCB L03M- A2-L Cabl e le ngth: 0.3m 2) Servo amplifier CN2 Cable model 1) CN2 connector 2) Junction connector MR-EKCBL M-L Receptacle: 36210-0100PL Shell kit: 36310-3200-008 (3M) Connector set: 54 ...

  • Mitsumi electronic MR-J3- A - page 318

    12 - 13 12. OPTIONS AND AUXILI ARY EQUIPMENT (b) Internal wiring diagram MR-EKCBL20M-L Encoder side Servo am plifier sid e 1 2 3 4 3 7 9 Plate 1 2 8 9 LG MR MRR SHD P5 BAT LG MR MRR SHD P5 BAT (Note) MR-EKCBL30M-L Encoder side Servo am plifier sid e P5 LG 1 2 MR MRR 3 4 MDR 8 5 3 7 4 MD 7 9 SD 1 2 8 9 LG MR MRR MDR MD SHD P5 6C O N T BAT BAT Plate ...

  • Mitsumi electronic MR-J3- A - page 319

    12 - 14 12. OPTIONS AND AUXILI ARY EQUIPMENT (c) When fabricating the encoder cable When fabricating the cable, prepare the following parts and fabrica te it according to the wiring diagram in (b). Refer to sec tion 12.11 for th e specifications of the used cable . Parts Description Connector set MR-ECNM Servo amplifier side connector Receptacle: 3 ...

  • Mitsumi electronic MR-J3- A - page 320

    12 - 15 12. OPTIONS AND AUXILI ARY EQUIPMENT (a) Connection of servo amplifier and servo motor Servo motor HF-MP HF-KP MR-J3JCBL03M-A2-L MR-EKCBL M-L/-H 1) Servo amplifier CN2 2) Servo motor HF-MP HF-KP MR-J3JCBL03M-A1-L 1) 2) or Cable model 1) Junction connec tor 2) For encoder connector MR-J3JCBL03M-A1-L Housing: 1-172169-9 Contact: 1473226-1 Cab ...

  • Mitsumi electronic MR-J3- A - page 321

    12 - 16 12. OPTIONS AND AUXILI ARY EQUIPMENT (4) MR-J3JSCBL03M-A1-L MR-J3JSCBL03M-A2-L The servo amplifier and servo motor cannot be connected with thes e cables only. The servo motor side encoder cable (MR- J3ENSCBL M-L/H) is required. Cable model Cable length IP ra ting Flex life Application MR-J3JSCBL03M-A1-L 0.3m IP65 Standard For HF-KP HF-M P ...

  • Mitsumi electronic MR-J3- A - page 322

    12 - 17 12. OPTIONS AND AUXILI ARY EQUIPMENT (b) Cable internal wiring dia gram P5 LG 8 5 MR MRR 1 2 1 3 Junction connector Encoder side connector 3 SHD 5 4 6 9 MR-J3JSCBL03M-A1-L MR-J3JSCBL03M-A2-L LG MR MRR SHD P5 CONT CONT 68 77 42 10 BAT BAT (5) MR-J3ENSCBL M-L(-S06) MR-J3ENSCBL M-H(-S06) These cables are encoder cables for HF-SP HA-LP HC-RP HC ...

  • Mitsumi electronic MR-J3- A - page 323

    12 - 18 12. OPTIONS AND AUXILI ARY EQUIPMENT (a) Connection of servo amplifier and servo motor Servo amplifier CN2 1) 2) MR-J3ENSCBL M-L(-S06) MR-J3ENSCBL M-H(-S06) Servo motor HF-SP HF-JP53(4) to 503(4) Cable model 1) For CN2 conn ector 2) Fo r encoder connector MR-J3ENSCBL M-L (-S06) Receptacle: 36210-0100PL Shell kit: 36310-3200-008 (3M) Connect ...

  • Mitsumi electronic MR-J3- A - page 324

    12 - 19 12. OPTIONS AND AUXILI ARY EQUIPMENT (b) Internal wiring diagram MR-J3ENSCBL2M-L(-S06)/H(-S0 6) MR-J3ENSCBL5M-L(-S06)/H(-S0 6) MR-J3ENSCBL10M-L(-S06)/H(-S06) P5 LG 1 2 MR MRR 3 4 4 8 9 SD 1 2 5 10 LG MR MRR SHD P5 BAT BAT Plate Servo amplifier side connector Encode r si de connector MR-J3ENSCBL20M-L(-S06) MR-J3ENSCBL30M-L(-S06) Plate P5 LG ...

  • Mitsumi electronic MR-J3- A - page 325

    12 - 20 12. OPTIONS AND AUXILI ARY EQUIPMENT (c) When fabricating the encoder cable When fabricating the cable, prepare the following parts and fabrica te it according to the wiring diagram in (b). Refer to sec tion 12.11 for th e specifications of the used cable . Parts (Connector set) Description MR-J3SCNS Servo amplifier side connector Receptacl ...

  • Mitsumi electronic MR-J3- A - page 326

    12 - 21 12. OPTIONS AND AUXILI ARY EQUIPMENT (6) MR-ENECBL M-H POINT The following encoder cables are of f our-wire type. When using any of these encoder cables, set parameter No. PC22 to "1 " to select the four-wire type. MR-ENECBL30M-H MR-ENECBL40M-H MR-ENECBL50M-H These cables are encoder cables for HF-JP11K1M(4) 15K1M(4) servo motors. ...

  • Mitsumi electronic MR-J3- A - page 327

    12 - 22 12. OPTIONS AND AUXILI ARY EQUIPMENT (a) Connection of servo amplifier and servo motor MR-EN ECBL M- H Servo amplifier 1) 2) CN2 Servo motor HF-JP11K1M(4) 15K1M(4) Cable model 1) For CN2 conn ector 2) Fo r encoder connector MR-ENECBL M-H Receptacle: 36210-0100PL Shell kit: 36310-3200-008 (3M) Connector set: 54599-1019 (Molex) Plug: D/MS3106 ...

  • Mitsumi electronic MR-J3- A - page 328

    12 - 23 12. OPTIONS AND AUXILI ARY EQUIPMENT (b) Cable internal wiring dia gram 1) For less than 30m To fabricate, use the connector set MR-ECNS (IP2 0 compatible) or MR-ENECNS (IP67 compa tible). Use the following wiring diagram to fabricate a cable shorter than 30 m. MR-ENECBL20M-H (Note) Servo amplifi er side P5 LG 1 2 MR MRR 3 4 F S 9 SD C D R ...

  • Mitsumi electronic MR-J3- A - page 329

    12 - 24 12. OPTIONS AND AUXILI ARY EQUIPMENT (7) MR-J3BTCBL03M This cable is a battery connection c able . Use this cabl e to retain the current position even if the detector cable is disconnected from the servo amplifier. Cable model Cable length Application MR-J3BTCBL03M 0.3m For HF-MP HF-K P HF-SP HA-LP HC-RP HC-UP HC-LP HF-JP series serv o moto ...

  • Mitsumi electronic MR-J3- A - page 330

    12 - 25 12. OPTIONS AND AUXILI ARY EQUIPMENT 12.1.3 Motor power supply cables These are motor power supply cables for the HF-MP HF-KP series servo motors. The numerals in the Cable Length field of the table are the s ymbols entered in the part o f the cable model. The cables of th e lengths with the symbols are availa ble. Refer to section 3.10 whe ...

  • Mitsumi electronic MR-J3- A - page 331

    12 - 26 12. OPTIONS AND AUXILI ARY EQUIPMENT 12.1.4 Motor brake cables These are motor brake cables for the HF-MP HF-KP series servo motors. The numerals in the Cable Length field of the tab le are the symbols entered in the part of the cable model. The cables of the lengths with the symbols are available. Refer to section 3.11 when wiring. Cable m ...

  • Mitsumi electronic MR-J3- A - page 332

    12 - 27 12. OPTIONS AND AUXILI ARY EQUIPMENT 12.2 Regenerative options CAUTION The specified combinations of regenerativ e options and servo amplifiers may only be used. Otherwise, a fire may occur. (1) Combination and regenerative power The power values in the table are resi stor-generated powers and not rated powers. Servo amplifier Regenerative ...

  • Mitsumi electronic MR-J3- A - page 333

    12 - 28 12. OPTIONS AND AUXILI ARY EQUIPMENT Servo amplifier (Note 2) Regenerative power [W] External regenerative resistor (Accessory ) MR-RB5R [3.2 ] MR-RB9F [3 ] MR-RB5K-4 [10 ] MR-RB6K-4 [10 ] MR-J3-11KA-LR 500 (800 ) 500 (800) MR-J3-11KA-LW 500 (800) MR-J3-15KA-LR 850 (1300 ) 850 (1300 ) MR-J3-15KA-LW 850 (1300 ) MR-J3-11KA4-LR 500 (800 ) 500 ...

  • Mitsumi electronic MR-J3- A - page 334

    12 - 29 12. OPTIONS AND AUXILI ARY EQUIPMENT (b) Losses of servo motor and servo amp lifier in regenerative mode The following table lis ts the efficiencies and other data of the servo motor and servo amplifier in the regenerative mode. Servo amplifier Inverse efficiency [ ] Capacitor charging [J] Servo amplifier Inverse efficiency [ ] Capacitor ch ...

  • Mitsumi electronic MR-J3- A - page 335

    12 - 30 12. OPTIONS AND AUXILI ARY EQUIPMENT (3) Parameter setting Set parameter No.PA02 according to the option to be used. Selection of regenerative option 00: Regenerative option is not used For servo amplifier of 100W, regenerative resistor is not used. For servo ampli fier o f 200 to 7kW, bu ilt-in rege nerative resi stor i s used. Supplied re ...

  • Mitsumi electronic MR-J3- A - page 336

    12 - 31 12. OPTIONS AND AUXILI ARY EQUIPMENT (4) Connection of the regenerative op tion POINT When the MR-RB50 MR-RB51 MR-RB3M-4 MR-RB3G-4 MR-RB5G-4 MR-RB34-4 MR-RB54-4 is used, a cooling fan is required to cool it. T he cooling fan should be prepared by the customer. For the sizes of wires used for wiring, refer to section 12.11. The regenerative ...

  • Mitsumi electronic MR-J3- A - page 337

    12 - 32 12. OPTIONS AND AUXILI ARY EQUIPMENT (b) MR-J3-350A4 MR-J3-500A(4) MR-J3-700A(4) Always remove the wiring (across P-C) of the se rvo amplifier built-in r egener ative resistor and fit the regenerative option across P-C. The G3 and G4 terminals act as a thermal s ensor. G3-G4 is opened when the regenerative option overheats abnormally. P C G ...

  • Mitsumi electronic MR-J3- A - page 338

    12 - 33 12. OPTIONS AND AUXILI ARY EQUIPMENT The drawing below shows the MR-J3-350A4 and MR-J 3-500A (4). Refer to section 10.1 (6) Outline Drawings for the position of the fixing screw for MR-J3-700A (4). Built-in regenerati ve resistor lead terminal fixing screw ...

  • Mitsumi electronic MR-J3- A - page 339

    12 - 34 12. OPTIONS AND AUXILI ARY EQUIPMENT (c) MR-J3-11KA(4)(-LR) MR-J3-15KA(4)(-LR) MR-J3-22KA(4) (when using the supplied regenerative resistor) CAUTION The regenerative resistor supplied with 1 1 kW to 22 kW servo ampl ifiers does not have a protect cover. Touc hing the resistor (including wiring/screw hole area) may cause a burn injury and el ...

  • Mitsumi electronic MR-J3- A - page 340

    12 - 35 12. OPTIONS AND AUXILI ARY EQUIPMENT (d) MR-J3-11KA(4)-PX/LW MR-J3-15KA(4)-PX/LW MR-J3-22KA(4)-PX (when using the regenerative option) The MR-J3-11KA(4)-PX to MR-J3-22KA(4)-PX servo amplifiers are not s upplied with regenerative resistors. When using any of thes e servo amplifiers, always use the MR-RB5E, 9P, 9F, 6B-4, 6 0-4 and 6K-4 regene ...

  • Mitsumi electronic MR-J3- A - page 341

    12 - 36 12. OPTIONS AND AUXILI ARY EQUIPMENT When using cooling fans, install them using the mounting holes provided in the bo ttom of the regenerative option. In this case, set " FA" in parameter No.PA02 . Mounti ng screw 4-M3 MR-RB5E 9P 9F 6B-4 60-4 6K-4 Top Bottom TE1 G4 G3 C P TE 2 cooling fans (92 92 m inimum a ir flow: 1.0m 3 ) (5) ...

  • Mitsumi electronic MR-J3- A - page 342

    12 - 37 12. OPTIONS AND AUXILI ARY EQUIPMENT (b) MR-RB30 MR-RB31 MR-RB32 MR-RB34-4 MR-RB3M-4 MR-RB3G-4 [Unit: mm] 7 10 90 100 B A 318 82.5 101.5 Cooling fan mounting screw (2-M4 screw) Air intake Terminal block G3 G4 P C Terminal screw: M4 Tightening torque: 1.2 [N m] (10.62 [lb in]) Mounting screw Screw size: M6 Tightening torque: 5.4 [N m] (47.79 ...

  • Mitsumi electronic MR-J3- A - page 343

    12 - 38 12. OPTIONS AND AUXILI ARY EQUIPMENT (d) MR-RB5E MR-RB5R MR-RB9P MR-RB9F MR-RB5K-4 MR-RB6B-4 MR-RB60-4 MR-RB6K-4 [Unit: mm] 260 230 10 2- 10 mounting hole 197 15 2.3 Air intake 215 15 230 15 15 15 82.5 82.5 Cooling fan mounting screw 4-M3 screw Terminal block G3 G4 P C Terminal screw: M5 Tightening torque: 2.0 [N m] (17.70 [lb in]) Mounting ...

  • Mitsumi electronic MR-J3- A - page 344

    12 - 39 12. OPTIONS AND AUXILI ARY EQUIPMENT (f) MR-RB1H-4 [Unit: mm] 6 2 149 173 6 Approx. 24 15 36 40 6 mounting hole Terminal signal layout G3 G4 P C Applicable wire size: 0.2 to 4.0mm 2 (AWG24 to AWG10) Tightening torque: 0.5 to 0.6 [N m] (4.43 to 5.31 [lb in]) Mounting screw Screw size: M5 Tightening torque: 3.24 [N m] (28.32 [lb in]) Mass: 1. ...

  • Mitsumi electronic MR-J3- A - page 345

    12 - 40 12. OPTIONS AND AUXILI ARY EQUIPMENT 12.3 FR-BU2-(H) brake unit POINT Use a 200V class brake unit and a resistor uni t with a 200V class servo amplifier, and a 400V class brake unit and a resistor unit with a 400V class servo amplifier. Combination of different voltage class un its and servo amplifier cannot be used. Install a brake unit an ...

  • Mitsumi electronic MR-J3- A - page 346

    12 - 41 12. OPTIONS AND AUXILI ARY EQUIPMENT 12.3.1 Selection Use a combination of servo amplifier, brake unit and resist or unit listed below. Brake unit Resistor unit Number of connected units Permissible continuous power [kW] Total resistance [ ] Applicable servo amplifier 200V class FR-BU2-15K FR-BR-15K 1 0.99 8 MR-J3-500A (Note) 2(parallel) 1. ...

  • Mitsumi electronic MR-J3- A - page 347

    12 - 42 12. OPTIONS AND AUXILI ARY EQUIPMENT 12.3.3 Connection exampl e POINT Connecting PR terminal of the brake unit to P terminal of the servo amplifier results in brake unit malfunction. Always connect t he PR terminal of the brake unit to the PR terminal of the resistor unit. (1) Combination with FR-BR-(H) resistor unit (a) When connecting a b ...

  • Mitsumi electronic MR-J3- A - page 348

    12 - 43 12. OPTIONS AND AUXILI ARY EQUIPMENT (b) When connecting two brake units to a servo amplifier POINT To use brake units with a parallel connec ti on, use two sets of FR-BU2 brake unit. Combination with other brake unit results in alarm occurrence or malfunction. Always connect the master and slave terminals (MSG and SD) of th e two brake uni ...

  • Mitsumi electronic MR-J3- A - page 349

    12 - 44 12. OPTIONS AND AUXILI ARY EQUIPMENT RA1 ALM Servo motor thermal relay RA2 (Note 7) MC ON Emerge ncy stop (Note 12) SK Termin al block (Note 11) P 1 P 2 P N C (Note 3) (Not e 2) (Note 8) MC NFB N/ P/ BUE SD PR B C A SD MSG (Note 4) (Not e 6) FR-BU2 -(H) FR-BR P PR TH2 TH1 (Note 5) L 1 L 2 L 3 L 11 L 21 (Note 9) 21 48 20 46 42 15 24VDC RA1 ( ...

  • Mitsumi electronic MR-J3- A - page 350

    12 - 45 12. OPTIONS AND AUXILI ARY EQUIPMENT (2) Combination with MT-BR5-(H) resistor unit RA4 (Note 3) (Note 6) FR-BU2-(H) MT-BR5-(H) (Note 5) (Not e 9) P 1 P( ) N( ) (Note 8) (Not e 2) C( N o t e 1 0 ) MC NFB BUE SD PR B C A SD MSG P PR TH2 TH1 L 1 L 2 L 3 L 11 L 21 CN1 21 DICOM 48 ALM 20 DICOM 46 DOCOM 42 EMG 15 SON Plate SD 24VDC RA1 RA4 OFF MC ...

  • Mitsumi electronic MR-J3- A - page 351

    12 - 46 12. OPTIONS AND AUXILI ARY EQUIPMENT (3) Precautions for wiring The cables between the servo amplifier a nd the brake unit, and between the resistor unit and the brake unit should be as short as possible. Alwa ys twist the cable longer than 5m (twist five times or more per one meter). Even when the cable is twis ted, the cable should be les ...

  • Mitsumi electronic MR-J3- A - page 352

    12 - 47 12. OPTIONS AND AUXILI ARY EQUIPMENT 2) Control circuit terminal POINT Undertightening can cause a cable disconnec tion or malfunction. O vertightening can cause a short circuit or malfunction d ue to damage to the screw or the brake unit. A RES PC B SD BUE C MSG SD MSG SD SD Jumper Terminal block 6mm Sheath Core Wire the stripped cable aft ...

  • Mitsumi electronic MR-J3- A - page 353

    12 - 48 12. OPTIONS AND AUXILI ARY EQUIPMENT (5) Crimping terminals for P and N terminals of servo amplifier (a) Recommended crimping terminals POINT Always use recommended crimping terminal s or equivalent since some crimping terminals cannot be installe d depending on the size. Servo amplifier Brake unit Number of connected units Crimping termina ...

  • Mitsumi electronic MR-J3- A - page 354

    12 - 49 12. OPTIONS AND AUXILI ARY EQUIPMENT 12.3.4 Outline dimension drawings (1) FR-BU2-(H) brake unit [Unit: mm] FR-BU2-15K Rating plate 5 hole (Screw size: M4) 68 6 56 6 5 18.5 52 62 4 132.5 FR-BU2-30K FR-BU2-H30 K 129.5 5 59 18.5 Rating plate 52 2- 5 hole (Screw size: M4) 5 108 6 6 96 FR-BU2-55K FR-BU2-H55K, H75K 18.5 Rating plate 52 72 5 142. ...

  • Mitsumi electronic MR-J3- A - page 355

    12 - 50 12. OPTIONS AND AUXILI ARY EQUIPMENT (2) FR-BR-(H) resistor unit [Unit: mm] 2 C Control circuit terminal Main circuit terminal W1 1 Approx. 35 Approx. 35 204 Hanging bolt C C W 5 For FR-BR-55K/FR-BR-H55K, a hanging bolt is placed on two locations (Indicated below). (Note) (Note) Note. Ventilation ports are provided on both sides and the top ...

  • Mitsumi electronic MR-J3- A - page 356

    12 - 51 12. OPTIONS AND AUXILI ARY EQUIPMENT 12.4 Power regenerative converter POINT When using the FR-RC-(H) power regener ative converter, refer to "Power Regeneration Converter FR-RC Inst ruction Manual (IB(NA)66330)". When using the power regenerative converter , set " 01" in parameter No.PA02 . (1) Selection The converters ...

  • Mitsumi electronic MR-J3- A - page 357

    12 - 52 12. OPTIONS AND AUXILI ARY EQUIPMENT (2) Connection example P/ N/ Ready NCP 5m or less RDY output (Note 2) BC Power factor improving AC reactor (Note 8) SON (Note 6) Power supply R RX R SX S TX T R/L 1 S/L 2 T/L 3 B C EMG CN1 DOCOM DICOM ALM CN1 24VDC Trouble Servo-on (Note 3) (Note 3) DOCOM Emergency s top (Note 7) (Note5) Power re generat ...

  • Mitsumi electronic MR-J3- A - page 358

    12 - 53 12. OPTIONS AND AUXILI ARY EQUIPMENT (3) Outside dimensions of the power regenerative con verters [Unit : mm] AA A C F K EE BA B E D 2- D ho le Rati ng plat e Front cover Display panel window Moun ting f oot (re movab le) Mounting foot movable Cooling fan Heat generation area outside mounting dimension Power regenerative converter A AA B BA ...

  • Mitsumi electronic MR-J3- A - page 359

    12 - 54 12. OPTIONS AND AUXILI ARY EQUIPMENT 12.5 Power regenerative common converter POINT Use the FR-CV for the servo amplifier of 200V class and the FR-CV-H for that of 400V class. For details of the power reg enerative co mmon converter FR-CV-(H), re fer to the FR-CV-(H) Installation Guide (IB(NA)0600075). Do not supply power to the main circui ...

  • Mitsumi electronic MR-J3- A - page 360

    12 - 55 12. OPTIONS AND AUXILI ARY EQUIPMENT The following table lists the restrictions. Item FR-CV- 7.5K 11K 15K 22K 30K 37K 55K Maximum number of connected servo amplifiers 6 Total of connectable servo amplifier c apacities [kW] 3.75 5.5 7.5 11 15 18.5 27.5 Total of connectable servo motor rated currents [A] 33 46 61 90 115 145 215 Maximum servo ...

  • Mitsumi electronic MR-J3- A - page 361

    12 - 56 12. OPTIONS AND AUXILI ARY EQUIPMENT (3) Connection diagram (a) 200V class Thermal relay MC NFB R/L 11 3-ph ase 200 to 230VAC S/L 21 T/L 31 R2/L 1 S2/L 22 R2/L 12 T2/L 32 S2/L 2 (Note 3) P24 SD RDYB RDYA RSO SE T2/L 3 R/L 11 S/L 21 T/MC1 RES SD (Note 1) L 11 L 21 RES U V W CN2 FR-CVL FR-C V MC RA2 RA3 RA4 EMG OFF ON RESET (Note 2) (Note 1) ...

  • Mitsumi electronic MR-J3- A - page 362

    12 - 57 12. OPTIONS AND AUXILI ARY EQUIPMENT (b) 400V class Thermal relay MC NFB R/L 11 3-ph ase 380 t o 480VAC S/L 21 T/L 31 R2/L 1 S2/L 22 R2/L 12 T2/L 32 S2/L 2 (Note 3) P24 SD RDYB RDYA RSO SE T2/L 3 R/L 11 S/L 21 T/MC1 RES SD (Note 1) L 11 L 21 RES U V W CN2 FR-CVL-H FR-CV-H MC RA2 RA3 RA4 EMG OFF ON RESET (Note 2) (Note 1) Servo amplifier RA2 ...

  • Mitsumi electronic MR-J3- A - page 363

    12 - 58 12. OPTIONS AND AUXILI ARY EQUIPMENT (4) Selection example of wires used for wiring POINT Selection condition o f wire size is as follow s. Wire type: 600V Polyvinyl chloride insula ted wire (IV wire) Construction condition: One wire is constructed in the air (a) Wire sizes 1) Across P-P ( ), N-N ( ) The following table indica tes the conne ...

  • Mitsumi electronic MR-J3- A - page 364

    12 - 59 12. OPTIONS AND AUXILI ARY EQUIPMENT (b) Examp le of select ing the wire sizes When connecting multiple servo amp lifiers, always use junction terminals for wiring the servo amplifier terminals P, N. Also, connect the servo amplifiers in th e order of larger to smaller capacities. 1) 200V class R2/L 1 S2/L 2 T2/L 3 R/L 11 S/L 21 T/MC1 P/L N ...

  • Mitsumi electronic MR-J3- A - page 365

    12 - 60 12. OPTIONS AND AUXILI ARY EQUIPMENT (5) Other precautions (a) Always use the dedicated stand-alon e reactor (FR-CVL-(H)) as the power factor improving reactor. Do not use power factor improving AC reactor (FR-BAL -( H)) or power factor improving DC reactor (FR- BEL-(H)). (b) The inputs/outputs (ma in circuits) of the FR -CV-(H) and servo a ...

  • Mitsumi electronic MR-J3- A - page 366

    12 - 61 12. OPTIONS AND AUXILI ARY EQUIPMENT (6) Specifications Power regenerative common converter FR-CV- Item 7.5K 11K 15K 22K 30K 37K 55K Total of connectable servo amplifier capacities [kW] 3.75 5.5 7.5 11 15 18.5 27.5 Maximum servo amplifier capacity [kW] 3.5 5 7 11 15 15 22 Output Total of connectable servo motor rated currents [A] 33 46 61 9 ...

  • Mitsumi electronic MR-J3- A - page 367

    12 - 62 12. OPTIONS AND AUXILI ARY EQUIPMENT 12.6 External dynamic brake CAUTION Use an external dynamic brake for a serv o amplifier of MR-J3-11KA(4) to MR-J3- 22KA(4). Failure to do so will cause an accident because the servo motor does not stop immediately but coasts at an emerge ncy stop and such conditions.Ensure the safety in the entire syste ...

  • Mitsumi electronic MR-J3- A - page 368

    12 - 63 12. OPTIONS AND AUXILI ARY EQUIPMENT (2) Connection example Oper ation-re ady 13 U 14 V W Extern al dynami c brake a b RA2 (Note 5) L 11 L 21 Servo amplifier 15 SON L 3 L 2 L 1 RA2 42 EMG 46 DOCOM SD Pla te U V W U V W M Servo motor P P 1 (Not e 1) CN1 (Note 3) DB 20 DICOM 47 DOCOM 24VDC ALM 48 (Note 2) RA1 RA2 MC NFB MC ALM RA1 OFF ON MC ( ...

  • Mitsumi electronic MR-J3- A - page 369

    12 - 64 12. OPTIONS AND AUXILI ARY EQUIPMENT Servo motor rotation Coasting ON OFF Absent Invalid Valid Short Open a. Timing chart at alarm occurrence b. Timing chart at Emergency stop (EMG) validity ON OFF Coasting Dynamic brake Dynami c brak e Prese nt Dynamic brake interlo ck (DB) Trouble (ALM) Base Dynamic brake Emergency st op (EMG) (Note 2)15 ...

  • Mitsumi electronic MR-J3- A - page 370

    12 - 65 12. OPTIONS AND AUXILI ARY EQUIPMENT (3) Outline dimension drawing (a) DBU-11K DBU-15K DBU-22K C D 100 D 5 5 F 2.3 G (GND) a Termi nal block Tighte ning torque : 0.8 [ N m](7 [lb in] Screw: M3.5 E b 13 14 W V U Tightening torque: 1.2 [N m](10.6 [lb in]) Screw: M4 Dynamic brake A B C D E F G Mass [kg]([lb]) Connection wire [ mm 2 ] (Note) DB ...

  • Mitsumi electronic MR-J3- A - page 371

    12 - 66 12. OPTIONS AND AUXILI ARY EQUIPMENT (b) DBU-11K-4 DBU-22K-4 [Unit: mm] 15 51 25 15 73.75 7 25 150 1 0 200 170 1 7 8 . 5 1 7 9 . 5 15 2 6 0 2 8 0 4 3 1 0 2- 7Mounting hol e 195 2 2 8 2 6 2 6 210 2.3 Mass: 6.7[kg] Tightening torque: 0.8[N m](7[lb in]) a TE1 Screw: M3.5 b1 3 1 4 Terminal block W V U Tightening torque: 1.2[N m](10.6[lb in]) Sc ...

  • Mitsumi electronic MR-J3- A - page 372

    12 - 67 12. OPTIONS AND AUXILI ARY EQUIPMENT 12.7 Junction terminal bloc k MR-TB50 (1) How to use the junction terminal block Always use the junction ter minal block (MR-TB50) with the junction terminal block cable (MR-J2M- CN1TBL M) as a set. A connection example is shown below. Servo a mplifie r CN1 Juncti on termi nal bl ock MR-TB 50 Cable clam ...

  • Mitsumi electronic MR-J3- A - page 373

    12 - 68 12. OPTIONS AND AUXILI ARY EQUIPMENT (4) Junction terminal block cable MR-J2M-CN1TBL M (a) Model explanation Cable length[m] Symbol 05 1 0.5 1 Mode l: M R-J2 M-CN1TB L M (b) Connection diagram D7950 -B500 FL (Junc tion termin al side) 10150-6000EL (Servo am plifier side) SD SD Plate Signal Symbols Speed Torq ue Pin No. 1 2 3 4 5 6 7 8 9 10 ...

  • Mitsumi electronic MR-J3- A - page 374

    12 - 69 12. OPTIONS AND AUXILI ARY EQUIPMENT 12.8 MR Configurator The MR Configurator uses the communication func tion of the servo amplifier to perform parame ter setting changes, graph display, test operati on, etc. on a personal computer. (1) Specifications Item Description Compatibility with a servo amplifier The following table shows MR Config ...

  • Mitsumi electronic MR-J3- A - page 375

    12 - 70 12. OPTIONS AND AUXILI ARY EQUIPMENT (2) System configuration (a) Components To use this software, the following components are re q uired in addition to the servo amplifier and servo motor. Equipment (Note 1 ) Description (Note 2, 3) Personal comp uter OS IBM PC/AT compatible where the English version of Windows R 98, Windows R Me, Windows ...

  • Mitsumi electronic MR-J3- A - page 376

    12 - 71 12. OPTIONS AND AUXILI ARY EQUIPMENT (b) Connection with servo a mplifier 1) For use of USB To USB connector Servo am plifier CN5 USB cable MR-J3USBCBL3M (Option) Person al computer 2) For use of RS-422 To RS-232C connector Servo am plifier CN3 RS-422/232C conversion cable DSV-CABV (Diatrend) Person al computer 3) For use of RS-422 to ma ke ...

  • Mitsumi electronic MR-J3- A - page 377

    12 - 72 12. OPTIONS AND AUXILI ARY EQUIPMENT (c) To diagnose the trouble using diagno sis cable (MR-J3ACHECK) POINT The amplifier diagnosis function can be u s ed with the following software versions of the servo amplifier. Servo amplifier: A1 or la ter MR Configurator: A1 or later Turn the power on after al l connectors are connected. Do not conne ...

  • Mitsumi electronic MR-J3- A - page 378

    12 - 73 12. OPTIONS AND AUXILI ARY EQUIPMENT 12.9 Battery unit MR-J3BAT POINT Refer to appendix 7 and 8 for battery transportation and the new EU Battery Directive. (1) Purpose of use for MR-J3BAT This battery is used to construct an absolute position detection s ystem. Refer to section 14.3 for the fitting method, etc. (2) Year and month when MR-J ...

  • Mitsumi electronic MR-J3- A - page 379

    12 - 74 12. OPTIONS AND AUXILI ARY EQUIPMENT 12.10 Heat sink outside mounti ng attachment (M R-J3ACN) Use the heat sink outside mounting atta chment to mount the heat generation ar ea of the servo amplifier in th e outside of the control bo x to dissipate servo amplifier-g enerated heat to the ou tside of the box an d reduce the amount of heat gene ...

  • Mitsumi electronic MR-J3- A - page 380

    12 - 75 12. OPTIONS AND AUXILI ARY EQUIPMENT (3) Fitting method Attachment Fit using the assembling screws. Serv o ampl if ier Attachment Servo amplifier Punched hole Control box a. Assembling the heat sink outside mounting atta chment b. Installation to the control box (4) Outline dimension drawing [Unit: mm] 236 280 Approx.260 20 3.2 105 155 Appr ...

  • Mitsumi electronic MR-J3- A - page 381

    12 - 76 12. OPTIONS AND AUXILI ARY EQUIPMENT 12.11 Selection example of wires POINT Wires indicated in this section are separated wires. Wh en using a cable for power line (U, V, and W) between the servo amplifier and servo motor, use a 600V grade EP rubber insulated chloroprene sheath cab-tire cable (2PNCT). For selection o f cables, refer to appe ...

  • Mitsumi electronic MR-J3- A - page 382

    12 - 77 12. OPTIONS AND AUXILI ARY EQUIPMENT (a) When using the 600V Polyvinyl chloride insulated wire (IV wire) Selection example of wire s ize when using IV wires is indicated be low. Table 12.1 Wire size select ion example 1 (IV wire) Servo amplifier Wires [mm 2 ] (Not e 1, 4) 1) L 1 L 2 L 3 2) L 11 L 21 3) U V W 4) P C 5) B1 B2 6) BU BV BW 7) O ...

  • Mitsumi electronic MR-J3- A - page 383

    12 - 78 12. OPTIONS AND AUXILI ARY EQUIPMENT (b) When using the 600V Grade heat-resistant polyv inyl chloride insulated wire (HIV wire) POINT Refer to the table 12.3 whe n using the HF-JP series servo mo tor of 0.5k to 5kW with the 400 maximum torque setting. Selection example of wire s ize when using HIV wires is indicated below. For the wire (8)) ...

  • Mitsumi electronic MR-J3- A - page 384

    12 - 79 12. OPTIONS AND AUXILI ARY EQUIPMENT Table 12.3 Wire size select ion example 3 (HIV wire) for the HF-JP series with the 400 maximum torque setting HF-JP servo motor Servo amplifier Wire [mm 2 ] (Not e 1) 1) L 1 L 2 L 3 2) L 11 L 21 3) U V W 4) P C 5) B1 B2 53 MR-J3-100A 73 MR-J3-200A 2(AWG14 ) 1.25(AWG16) 103 1.25(AWG16) 2(AWG14) 153 MR-J3- ...

  • Mitsumi electronic MR-J3- A - page 385

    12 - 80 12. OPTIONS AND AUXILI ARY EQUIPMENT (2) Wires for cables When fabricating a cable, use the wire models given in the following table or equivalent. Table 12.3 Wires for option cables TypeEncod er cable Model Length [m] Core size [mm 2 ] Number of Cores Characteristics of one core (Note 3) Finishing OD [mm] Wire model Structure [Wires/mm] Co ...

  • Mitsumi electronic MR-J3- A - page 386

    12 - 81 12. OPTIONS AND AUXILI ARY EQUIPMENT Note 1. d is as shown below. d Conduc tor Insulation sheath 2. Purchase from Toa Electric Industry 3. Standard OD. Max. OD is about 10 greater. 4. Purchase from Taisei 5. Taiyo Electric Wire and Cable 6. These wire sizes assume that the UL-compliant wires are used at the wiring length of 10m. 7. These mo ...

  • Mitsumi electronic MR-J3- A - page 387

    12 - 82 12. OPTIONS AND AUXILI ARY EQUIPMENT 12.13 Power factor improving DC re actor POINT For the 100VAC power supply type (MR-J3- A1), the p ower factor improving DC reactor cannot be used. The power factor improving DC reactor increases the form factor of the servo a mplifier's input current to improve the power factor . It can decrease th ...

  • Mitsumi electronic MR-J3- A - page 388

    12 - 83 12. OPTIONS AND AUXILI ARY EQUIPMENT Servo amplifier Power factor improving DC reactor Outline drawing Dimensions [mm] Mounting screw size Mass [kg(lb)] Wire [mm 2 ] (Note) A B C D E F L G H MR-J3-10A 20A FR-BEL-0.4K 110 50 94 1.6 95 6 12 M3.5 25 M5 0.5(1.10) MR-J3-40A FR-BEL-0.75K 120 53 102 1.6 105 6 12 M4 25 M5 0.7(1.54) MR-J3-60A 70A FR ...

  • Mitsumi electronic MR-J3- A - page 389

    12 - 84 12. OPTIONS AND AUXILI ARY EQUIPMENT 12.14 Power factor improving re actors The power factor improving reactors impr ove the phase fac t or by increasing the form fac tor of servo amplifier' s input current. It can reduce the power capacity. The input power factor is improved to be about 90 . For use with a 1-phase power supply, it may ...

  • Mitsumi electronic MR-J3- A - page 390

    12 - 85 12. OPTIONS AND AUXILI ARY EQUIPMENT Servo amplifier Model Dimensions [mm] Mounting screw size Terminal screw size Mass [kg (lb)] W W1 H D D1 C MR-J3-10A 20A 10A1 FR-BAL-0.4K 135 120 115 59 45 0 -2.5 7.5 M4 M3.5 2.0 (4.4 1) MR-J3-40A 20A1 FR-BAL-0.75K 135 120 115 69 57 0 -2.5 7.5 M4 M3.5 2.8 (6.1 7) MR-J3-60A 70A 40A1 FR-BAL-1.5K 160 145 14 ...

  • Mitsumi electronic MR-J3- A - page 391

    12 - 86 12. OPTIONS AND AUXILI ARY EQUIPMENT 12.16 Surge absorbers (recommended) A surge absorber is required for the electromagnetic br ake. Use the following surge absorber or equivalen t. When using the surge absorber, perform insula tion beforehand to prevent short-circuit. Maximum rating Maximum limit voltage Static capacity (reference value) ...

  • Mitsumi electronic MR-J3- A - page 392

    12 - 87 12. OPTIONS AND AUXILI ARY EQUIPMENT (c) Techniques for noises radiated by the servo ampl ifier tha t cause peripheral devices to malfunction Noises produced by the servo amplifier are classified into those radiated from the cables connected to the servo amplifier and its main circuits ( input and ou tput circuits), those i nduced electroma ...

  • Mitsumi electronic MR-J3- A - page 393

    12 - 88 12. OPTIONS AND AUXILI ARY EQUIPMENT Noise transmission route Suppression techniques 1) 2) 3) When measuri ng instrumen ts, receivers, se nsors, etc. which handle w eak signals and may malfunc tion due to noise a nd/or thei r signal cables a re contained in a control bo x together with the servo amplifier or run near th e servo amplifi er, ...

  • Mitsumi electronic MR-J3- A - page 394

    12 - 89 12. OPTIONS AND AUXILI ARY EQUIPMENT (b) Surge killer The recommended surge killer for installa tion to an AC r elay, AC valve or the like n ear the servo amplifier is shown below. Use this product or equivalent. MC SK Surge killer Relay Surge killer MC ON OFF This distance should be short (within 20cm). (Ex.) CR-50500 (OKAYA Electric Indus ...

  • Mitsumi electronic MR-J3- A - page 395

    12 - 90 12. OPTIONS AND AUXILI ARY EQUIPMENT Outline drawing Eart h plate Clam p secti on dia gram (Note)M4 sc rew 1 1 3 6 C A 6 22 17.5 35 3 5 L or les s 10 3 0 7 2 4 0 0 . 2 2 4 0 . 3 0 [Unit: mm] B 0 . 3 2- 5 ho le installation hole Note. Screw hole for grounding. Connect it to the earth plate of the control box. Type A B C Accessory fittings Cl ...

  • Mitsumi electronic MR-J3- A - page 396

    12 - 91 12. OPTIONS AND AUXILI ARY EQUIPMENT (d) Line noise filter (FR-BSF01, FR-BLF) This filter is effective in suppressing noises radi ated fr om the power supply side and output side of the servo amplifier and also in suppressing high-frequen cy leakage current (zero-phase current) especially within 0.5M to 5MHz band. Connection diagram Outline ...

  • Mitsumi electronic MR-J3- A - page 397

    12 - 92 12. OPTIONS AND AUXILI ARY EQUIPMENT (e) Radio noise filter ( FR-BIF-(H)) This filter is effective in suppressing noises radiated from the power supply side of the servo amplifier especially in 10MHz and lower radio frequency bands. T he FR-BIF-(H) is designed for the input only. 200V class: FR-BIF 400V class: FR-BIF-H Connection diagram Ou ...

  • Mitsumi electronic MR-J3- A - page 398

    12 - 93 12. OPTIONS AND AUXILI ARY EQUIPMENT (f) Varistors for input power supply (Recommended) Varistors are effective to prevent exogenous noise and lightning surge from enterin g the servo amplifier. When using a varistor, connect it between each phase of the inpu t power supply of the equipme nt. For varistors, the TND20V-431K, T ND20V-471K and ...

  • Mitsumi electronic MR-J3- A - page 399

    12 - 94 12. OPTIONS AND AUXILI ARY EQUIPMENT 12.18 Leakage current bre aker (1) Selection method High-frequency chopper currents controlled by pulse width modulation flow in the AC servo circuits. Leakage currents containing harmonic contents are larger than those of the motor which is run with a commercial power supply. Select a leakage current br ...

  • Mitsumi electronic MR-J3- A - page 400

    12 - 95 12. OPTIONS AND AUXILI ARY EQUIPMENT Table 12.4 Servo motor’s leakage current example (Igm) T able 12.5 Servo amplifier's leakage current example (Iga) Servo motor power [kW] Leakage current [mA] Servo amplifier capacity [kW] Leakage current [mA] 0.05 to 1 0.1 0.1 to 0.6 0.1 2 0.2 0.75 to 3.5 (Note) 0.15 3.5 0.3 5 7 2 5 0.5 11 15 5.5 ...

  • Mitsumi electronic MR-J3- A - page 401

    12 - 96 12. OPTIONS AND AUXILI ARY EQUIPMENT 12.19 EMC filter (recommended) For compliance with the EMC directive of the IEC/EN Standard, it is recommended to use the following filter. Some EMC filters are large in leakage current. (1) Combination with the servo amplifier Servo amplifier Recommended fi lter (Soshin Electric) Mass [kg]([lb]) Model L ...

  • Mitsumi electronic MR-J3- A - page 402

    12 - 97 12. OPTIONS AND AUXILI ARY EQUIPMENT (3) Outline drawing (a) EMC filter HF3010A-UN [Unit: mm] M4 IN 3-M4 65 4 Approx.41 4-5.5 7 258 4 273 2 288 4 300 5 3-M4 85 2 32 2 110 4 HF3030A-UN HF-3040A-UN J 2 H 2 G 1 F 2 E 1 D 2 3-L 6-K 3-L M C 1 B 2 A 5 C 1 Model Dimensions [mm] A B C D E F G H J K L M HF3030A-UN 260 210 85 155 140 125 44 140 70 R3 ...

  • Mitsumi electronic MR-J3- A - page 403

    12 - 98 12. OPTIONS AND AUXILI ARY EQUIPMENT HF3100A-UN 2-6.5 8 M8 145 1 165 3 M6 380 1 400 5 160 3 M8 2- 6.5 TF3005C-TX TX3020C-TX TF3030C-TX [Unit: mm] 290 2 100 1 308 5 332 5 Appro x.12. 2 3-M4 16 16 6-R3.25 length8 M4 M4 125 2 140 1 155 2 IN 150 2 Appro x.67. 5 3 Appro x.160 170 5 M4 3 M4 100 1 ...

  • Mitsumi electronic MR-J3- A - page 404

    12 - 99 12. OPTIONS AND AUXILI ARY EQUIPMENT TF3040C-TX TF3060C-TX [Unit: mm] K 2 L J H 5 M6 C 2 D 1 B 5 A 5 Approx. 17 3-M6 22 22 8-M M4 M4 G 2 3-M6 F 1 E 2 IN D 1 D 1 Model Dimensions [mm] A B C D E F G H J K L M TF3040C-TX 438 412 390 100 175 160 145 200 Approx.190 180 Approx. 91.5 R3.25 length 8 (M6) TF3060C-TX ...

  • Mitsumi electronic MR-J3- A - page 405

    12 - 100 12. OPTIONS AND AUXILI ARY EQUIPMENT (b) Surge protector RAV-781BYZ-2 4.5 0.5 1 3 2 41 1.0 28.5 1.0 28 1.0 4.2 0.2 200 30 0 UL-1015AWG16 5.5 1 11 1 [Unit: mm] Black 1) 2) 3) Black Black RAV-781BXZ-4 1 3 2 UL-1015AWG16 4.2 0.2 5.5 1 11 1 28.5 1.0 200 30 0 28 1.0 41 1.0 4.5 0.5 [Unit: mm] 1) 2) 3) 4) ...

  • Mitsumi electronic MR-J3- A - page 406

    13 - 1 13. COMMUNICATION FUNCTION 13. COMMUNICATION FUNCTION POINT The USB communication function (CN5 conn ector) and the RS-422 communication functio n (CN3 connector) ar e mutua lly exclusive functions. They cannot be used simultaneously. Using the serial communication func tion of RS-422, th is servo amplifier enables servo operation, parameter ...

  • Mitsumi electronic MR-J3- A - page 407

    13 - 2 13. COMMUNICATION FUNCTI ON (b) Cable connection diagram Wire the cables as shown below. 7 1 2 3 4 5 6 8 7 1 2 3 4 5 6 8 12345678 7 1 2 3 4 5 6 8 (Note 4 , 5) (Note 1) Axis 1 servo amplifier CN3 connec tor (RJ45 conne c tor) LG P5D RDP SDN SDP RDN LG NC (Note 5) (Note 5) 7 1 2 3 4 5 6 8 7 1 2 3 4 5 6 8 12345678 7 1 2 3 4 5 6 8 LG P5D RDP SDN ...

  • Mitsumi electronic MR-J3- A - page 408

    13 - 3 13. COMMUNICATION FUNCTI ON 13.2 Communication sp ecifications 13.2.1 Communication overview This servo amplifier is des igned to send a reply on re ceipt of an instruction. The device which gives this instruction (e.g. personal computer) is called a master station and the device which sends a reply in response to the instruction (servo am p ...

  • Mitsumi electronic MR-J3- A - page 409

    13 - 4 13. COMMUNICATION FUNCTI ON 13.2.2 Parameter setting When the USB/RS-422 communication function is us ed to operate the servo, set the communication specifications of the servo amplifier in the corresponding parameters. After setting the values of these par ameters, they are made valid by switching power off once, then on again. (1) Serial c ...

  • Mitsumi electronic MR-J3- A - page 410

    13 - 5 13. COMMUNICATION FUNCTI ON 13.3 Protocol 13.3.1 Transmission data configuratio n Since up to 32 axes may b e connected to the bus, add a station number to the command, data No., etc. to determine the destination servo amplifier of data co mmunication . Set the sta tion number to each servo amplifier using the parameter. Transmissi on data i ...

  • Mitsumi electronic MR-J3- A - page 411

    13 - 6 13. COMMUNICATION FUNCTI ON 13.3.2 Character codes (1) Control codes Code name Hexadecimal (ASCII code) Description Personal computer terminal key operation (General) SOH STX ETX EOT 01H 02H 03H 04H start of head start of text end of text end of transmission ctrl A ctrl B ctrl C ctrl D (2) Codes for data ASCII unit codes are used. b 8 0 0 0 ...

  • Mitsumi electronic MR-J3- A - page 412

    13 - 7 13. COMMUNICATION FUNCTI ON 13.3.3 Error codes Error codes are used in the fo llowing cases and an error code of single-code length is transmitted. On receipt of data from the master sta tion, the slave sta tion sends the error code corresponding to that data to the master station . The error code sent in upper case indicates that the se rvo ...

  • Mitsumi electronic MR-J3- A - page 413

    13 - 8 13. COMMUNICATION FUNCTI ON 13.3.5 Time-out The master station transmits EOT when the slave station does not s tart repl y processing (STX is not received) 300[ms] after the master s tation has ended communic ation processing. 100[ms] after that, the master station retransmits the message. Time-out occurs if the slave station does not answer ...

  • Mitsumi electronic MR-J3- A - page 414

    13 - 9 13. COMMUNICATION FUNCTI ON 13.3.7 Initialization After the slave station is sw itched on, it cannot reply to communication until the inter nal initialization processing terminates. Hence, at power-on, ordinary communication should be started a fter. (1) 1s or longer time has elapsed after the slave statio n is switched on; and (2) Making su ...

  • Mitsumi electronic MR-J3- A - page 415

    13 - 10 13. COMMUNICATION FUNCTI ON 13.4 Command and data No. list POINT If the command and data No. are the same, the description may be different from that of the servo amplifier. 13.4.1 Read commands (1) Status display (Command [0][1]) Command Data No. Description Display item Frame length [0][1] [0][0] Status display name and unit Cumulative fe ...

  • Mitsumi electronic MR-J3- A - page 416

    13 - 11 13. COMMUNICATION FUNCTI ON (2) Parameters (Command [0][4] [0][5] [0 ][6] [0][7] [0][8] [0 ][9]) Command Data No. Description Frame length [0][4] [0][1] Parameter group read 0000: Basic setting parameter (No.PA ) 0001: Gain filter parameter (No.PB ) 0002: Extension setting parameter (No.PC ) 0003: I/O setting parameter (No.PD ) 4 [0][5] [0] ...

  • Mitsumi electronic MR-J3- A - page 417

    13 - 12 13. COMMUNICATION FUNCTI ON (4) Alarm history (Command [3][3]) Command Data No. Description Alarm occurrence sequence Frame length [3][3] [1][0] Alarm number in alarm history most recent alarm 4 [1][1] first alarm in past [1][2] second alarm in past [1][3] third alarm in past [1][4] fourth alarm in past [1][5] fifth alarm in past [2][0] Ala ...

  • Mitsumi electronic MR-J3- A - page 418

    13 - 13 13. COMMUNICATION FUNCTI ON Command Data No. Description Display item Frame length [3][5] [0][0] Status display name and unit at alarm occurrence Cumulative feedback pulse 16 [0][1] Servo motor speed [0][2] Droop pulse [0][3] Cumulative command pulse [0][4] Command pulse frequency [0][5] Analog speed command voltage Analog speed limit volta ...

  • Mitsumi electronic MR-J3- A - page 419

    13 - 14 13. COMMUNICATION FUNCTI ON 13.4.2 Write commands (1) Status display (Command [8][1]) Command Data No. Description Setting range Frame length [8][1] [0][0] Status display data erasure 1EA5 4 (2) Parameters (Command [8][4] [8][5]) Command Data No. Description Setting range Frame length [8][4] [0][1] to [F][F] Write of paramet ers Writes the ...

  • Mitsumi electronic MR-J3- A - page 420

    13 - 15 13. COMMUNICATION FUNCTI ON (7) Operation mode selection (Command [8][B]) Command Data No. Description Setting range Frame length [8][B] [0][0] Operation mode switching 0000: Test operation mode cancel 0001: JOG operation 0002: Positioning operation 0003: Motorless operation 0004: Output signal (DO) forced output 0000 to 0004 4 (8) Test ope ...

  • Mitsumi electronic MR-J3- A - page 421

    13 - 16 13. COMMUNICATION FUNCTI ON 13.5 Detailed explanations of command s 13.5.1 Data processing When the master station tr ansmits a command data No. or a command data No. data to a sla ve station, the servo amplifier returns a reply or data according to the purpose. When numerical values are represented in these send data and rece ive data, the ...

  • Mitsumi electronic MR-J3- A - page 422

    13 - 17 13. COMMUNICATION FUNCTI ON (2) Writing the processed data When the data to be written is hand led as decimal, the dec imal point position must be specified. If it is not specified, the data cannot be written. Wh en the data is handled as hexadecimal, specify "0 " as the decimal point position. The data to be sent is the following ...

  • Mitsumi electronic MR-J3- A - page 423

    13 - 18 13. COMMUNICATION FUNCTI ON 13.5.2 Status display (1) Reading the status display name and unit Read the status display name and un it. (a) Transmission Transmit command [0][1] and the da ta No. corresponding to the status display ite m to be read, [0][0] to [0][E]. (Refer to section 13.4.1.) (b) Reply The slave station sends back the stat u ...

  • Mitsumi electronic MR-J3- A - page 424

    13 - 19 13. COMMUNICATION FUNCTI ON 13.5.3 Parameters (1) Specify the parameter group The group of the parameters to be opera ted must be specif ied in advance to read or write the parameter settings, etc. Write data to the servo amplifier as described below to specify the parameter group to be operated. Command Data No. Transmission data Parameter ...

  • Mitsumi electronic MR-J3- A - page 425

    13 - 20 13. COMMUNICATION FUNCTI ON (4) Reading the setting Read the parameter setting. Specify the parameter group in advanc e (refer to (1) in this section). (a) Transmission Transmit command [0][5] and the da ta No. corresponding to the parameter No., [0][1] to [F][F]. (Refer to section 13.4.1.) The data No. is expressed in hexadecimal. The deci ...

  • Mitsumi electronic MR-J3- A - page 426

    13 - 21 13. COMMUNICATION FUNCTI ON (6) Parameter write POINT If setting values need to be changed with a high freq uency (i.e. one time or more per one hour), write the setting values to the RAM, not the EEP-ROM. The EEP- ROM has a limitation in the number of wr ite times and exce eding this limitation causes the servo amplifier to malfunction. No ...

  • Mitsumi electronic MR-J3- A - page 427

    13 - 22 13. COMMUNICATION FUNCTI ON 13.5.4 External I/O signal statuses (DIO diagnosis) (1) Reading of input device statuses Read the statuses of the input devices. (a) Transmission Transmit command [1][2] and data No.[0][0 ]. Command Data No. [1][2] [0][0] (b) Reply The slave station sends back the statuses of the input pins. b31 b0 0:OFF 1:ON b1 ...

  • Mitsumi electronic MR-J3- A - page 428

    13 - 23 13. COMMUNICATION FUNCTI ON bit CN1 connector pin bit CN1 connector p in bit CN1 connector pin bit CN1 connector pin 0 43 8 18 16 24 1 44 9 45 17 25 2 42 10 18 26 3 15 11 19 27 4 19 12 20 28 5 41 13 21 29 6 16 14 22 30 7 17 15 23 31 (3) Read of the statuses of input de vices switched on through communication Read the ON/OFF statuses of the ...

  • Mitsumi electronic MR-J3- A - page 429

    13 - 24 13. COMMUNICATION FUNCTI ON (4) External output pin status read Read the ON/OFF statuses of the external ou tput pins. (a) Transmission Transmit command [1][2] and data No.[C ][0]. Command Data No. [1][2] [C][0] (b) Reply The slave station sends back the ON/OFF statuses of the outpu t pins. b31 b0 0:OFF 1:ON b1 Command of each bit is transm ...

  • Mitsumi electronic MR-J3- A - page 430

    13 - 25 13. COMMUNICATION FUNCTI ON 13.5.5 Input device ON/OFF POINT The ON/OFF states of all devices in the se rvo a mplifier are the states of the data received last. Hence, when there is a device whi ch must be kept ON, send data which turns that device ON every time. Each input device can be s witched on/off. However, when the device to be swit ...

  • Mitsumi electronic MR-J3- A - page 431

    13 - 26 13. COMMUNICATION FUNCTI ON (2) Disabling/enabling the output device s (DO) Transmit the following communication commands. (a) Disable Command Data No. Data [9][0] [0][3] 1EA5 (b) Enable Command Data No. Data [9][0] [1][3] 1EA5 13.5.7 Input devices ON /OFF (test operation) Each input devices can be turned on/o ff for test operati on. when t ...

  • Mitsumi electronic MR-J3- A - page 432

    13 - 27 13. COMMUNICATION FUNCTI ON 13.5.8 Test operation mode POINT The test operation mode is used to confir m operation. Do not use it for actual operation. If communication stops for longe r than 0. 5s during test operation, the servo amplifier decelerates to a st op, resulting in servo lock. To preve nt this, continue communication all the tim ...

  • Mitsumi electronic MR-J3- A - page 433

    13 - 28 13. COMMUNICATION FUNCTI ON (2) JOG operation Send the command, data No. and data as i ndicated below to execute JOG operation. Command : [8][B] Data No . : [0][0] Data : 0001(JOG operation) When LSP/LSN was turned OFF by external input signal or automatically Command : [9][2] Data N o. : [0][ 0] Data : 00000007 (SON, LSP, LSN turned O N) C ...

  • Mitsumi electronic MR-J3- A - page 434

    13 - 29 13. COMMUNICATION FUNCTI ON (3) Positioning operation (a) Operation procedure Send the command, data No. and data as indica ted below to e xecute positioning operation. Command : [8][B] Data No. : [0][0] Data : 0002 (posit ioning ope ration) When LS P/LSN was turned OFF by exte rnal input signal or automatically turn ed ON Command : [9][2] ...

  • Mitsumi electronic MR-J3- A - page 435

    13 - 30 13. COMMUNICATION FUNCTI ON (b) Temporary stop/restart/remaining distance clear Send the following comman d, data No. and data during positioning operation to make deceleration to a stop. Command Data No. Data [A][0] [4][1] STOP Send the following comman d, data No. and data durin g a temporary stop to make a restart. Command Data No. (Note ...

  • Mitsumi electronic MR-J3- A - page 436

    13 - 31 13. COMMUNICATION FUNCTI ON (3) DO forced output Transmit command [8][B] data No.[0][0] data to choose DO forced output. Command Data No. Transmission data Test operation mode selection [8][B] [0][0] 0000 Test operation mode cancel 13.5.10 Alarm history (1) Alarm No. read Read the alarm No. which occurred in th e past. Th e alarm numbers an ...

  • Mitsumi electronic MR-J3- A - page 437

    13 - 32 13. COMMUNICATION FUNCTI ON 13.5.11 Current alarm (1) Current alarm read Read the alarm No. which is occurring currently. (a) Transmission Send command [0][2] and data No .[0][0]. Command Data No. [0][2] [0][0] (b) Reply The slave station sends back th e alarm currently occurring. 00 Alarm No. is transferred in hexadecimal. For example, &qu ...

  • Mitsumi electronic MR-J3- A - page 438

    13 - 33 13. COMMUNICATION FUNCTI ON 13.5.12 Other commands (1) Servo motor side pulse unit absolute position Read the absolute position in the servo motor side pulse unit. Note that overflow will occur in the positio n of 8192 or more revolutions from the home position. (a) Transmission Send command [0][2] and data No .[9][0]. Command Data No. [0][ ...

  • Mitsumi electronic MR-J3- A - page 439

    13 - 34 13. COMMUNICATION FUNCTI ON (3) Software version Reads the software version of the servo amplifier. (a) Transmission Send command [0][2] and data No .[7][0]. Command Data No. [0][2] [7][0] (b) Reply The slave station returns th e software version requested. Software version (1 5 digits) Space ...

  • Mitsumi electronic MR-J3- A - page 440

    14 - 1 14. ABSOLUTE POSITION DETECTION SYSTEM 14. ABSOLUTE POSITION DETECTION SYSTEM CAUTION If an absolute position erase (AL.25) or ab solute position counter warning (AL.E3) has occurred, always perform home position setting ag ain. Not doing so can cause runaway. Not doing so may cause unexpe cted operation. POINT If the encoder cable is discon ...

  • Mitsumi electronic MR-J3- A - page 441

    14 - 2 14. ABSOLUTE POSITION DET ECTION SYSTEM 14.1.2 Restrictions The absolute position detec tion system cannot be c onfigured under the following conditions . Test operation cannot be performed in the absolute position detection system, either. To per form test operation, choose incremental in parameter No.PA03. (1) Speed control mode, torque co ...

  • Mitsumi electronic MR-J3- A - page 442

    14 - 3 14. ABSOLUTE POSITION DET ECTION SYSTEM 14.2 Specifications (1) Specification list Item Description System Electronic battery backup system Battery 1 piece of lithium battery (primary battery, nominal 3.6V) Type: MR-J3BAT Maximum revolution range Home position 32767 rev. (Note 1) Maximum speed at power failure 3000r/min (Note 2) Battery back ...

  • Mitsumi electronic MR-J3- A - page 443

    14 - 4 14. ABSOLUTE POSITION DET ECTION SYSTEM 14.3 Battery replacement procedure WARN ING Before replacement a battery, turn off the main circuit p ower and wait for 15 minutes or longer (20 minutes for 30kW o r higher) until the charge la mp turns off. Then, check the voltage be tween P( ) and N( ) with a vo ltage tester or others. Otherwise, an ...

  • Mitsumi electronic MR-J3- A - page 444

    14 - 5 14. ABSOLUTE POSITION DET ECTION SYSTEM 14.4 Battery installation procedure POINT For the servo amplifier with a battery holder on the bottom, it is not possible to wire for the earth with the battery install ed. Insert the battery after executing the earth wiring of the servo am plifier. Insert connector into CN4. Insert connector into CN4. ...

  • Mitsumi electronic MR-J3- A - page 445

    14 - 6 14. ABSOLUTE POSITION DET ECTION SYSTEM 14.5.2 Replacement procedure MR-J3BTC BL03M CN4 CN2 Servo amplifier New MR-J3BAT MR-J3BAT for backup Old MR-J3BAT Step 1 Connect MR-J3BAT for backup to the battery connector of MR- J3BTCBL03M. MR-J3B TCBL 03M CN4 CN2 Servo amplifier New MR-J3BAT MR-J3BAT for ba ckup Old MR-J3BAT Step 2 Remove old MR-J3 ...

  • Mitsumi electronic MR-J3- A - page 446

    14 - 7 14. ABSOLUTE POSITION DET ECTION SYSTEM 14.6 Standard connection diagram Analog torque limit 10V/max.torque Proximity dog signal Stop signal Power supply (24V) Ready Zero-point signal Clear Command pulses (for diffe rential line driver type) Reset CR DOCOM 20 46 DOCOM 43 LSP 44 LSN 18 TL 19 RES 46 DOCOM 15 SON 42 EMG 17 ABSM 18 ABSR 22 ABSB0 ...

  • Mitsumi electronic MR-J3- A - page 447

    14 - 8 14. ABSOLUTE POSITION DET ECTION SYSTEM 14.7 Signal explanation When the absolute position data is transferred, the si gnals of connector CN1 change as described in this section. They return to the p revious status on completi o n of data transfer. The other signals are as described in section 3.5. For the I/O in terfaces (symbols in the I/O ...

  • Mitsumi electronic MR-J3- A - page 448

    14 - 9 14. ABSOLUTE POSITION DET ECTION SYSTEM 14.8 Startup procedure (1) Battery installation . Refer to section 14.3. (2) Parameter setting Set " 1"in parameter No.PA03 of the servo amplifier an d switch power off, then on. (3) Resetting of absolute p osition erase (AL.25) After connecting the encoder cable, th e absolute position erase ...

  • Mitsumi electronic MR-J3- A - page 449

    14 - 10 14. ABSOLUTE POSITION DET ECTION SYSTEM 14.9 Absolute position data transfer protocol POINT After switching on the ABS transfer mode (ABSM), turn on the servo-on signal (SON). When the ABS transfe r mode is off, turning on the servo-on signal (SON) does not switch on the base circuit. 14.9.1 Data transfer procedure Each time the servo-on (S ...

  • Mitsumi electronic MR-J3- A - page 450

    14 - 11 14. ABSOLUTE POSITION DET ECTION SYSTEM 14.9.2 Transfer method The sequence in which the base circuit is turned ON (servo -on) when it is in the OFF sta te due to the servo -on (SON) going OFF, an emergency stop (EMG), or alarm (A LM), is e xplained below. In the absolute position detection system, e very time the servo-on (SON) is tur ned ...

  • Mitsumi electronic MR-J3- A - page 451

    14 - 12 14. ABSOLUTE POSITION DET ECTION SYSTEM 1) The ready (RD) is turned ON when the ABS transfer mode (ABSM) is turned OFF after transmission of the ABS data. While the ready (RD) is ON, the ABS tran sfer mode (ABSM) input is not accepted. 2) Even if the servo-on (SON ) is turned ON bef ore the ABS transfer mode (ABSM) is turned ON , the base c ...

  • Mitsumi electronic MR-J3- A - page 452

    14 - 13 14. ABSOLUTE POSITION DET ECTION SYSTEM (b) Detailed description of absolute position data transfer OFF ON OFF ON OFF ON OFF ON OFF ON 3) 4) 5) 7) (Note) 1) 2) 6) Servo-on in progr ammabl e controlle r Servo-on (SON) A BS transfer mode (ABSM) A BS requ est (ABSR) A BS transmission data ready (ABST) Transmission (ABS) data During transfer of ...

  • Mitsumi electronic MR-J3- A - page 453

    14 - 14 14. ABSOLUTE POSITION DET ECTION SYSTEM (c) Checksum The checksum is the code which is used by the progr ammable controller to check for errors in the received ABS data. The 6-bit checksum is transmitted following the 32-bit ABS data. At the programmable controller, calculate the sum of the received ABS data using the ladder program and com ...

  • Mitsumi electronic MR-J3- A - page 454

    14 - 15 14. ABSOLUTE POSITION DET ECTION SYSTEM (2) Transmission error (a) Time-out warning(AL.E5) In the ABS transfer mode, the time-out processing show n below is executed at th e servo. If a time-out error occurs, an ABS time-out warning (AL.E5) is output. The ABS time-out warning (AL.E5) is cleared when the ABS transfer mode (ABSM) changes from ...

  • Mitsumi electronic MR-J3- A - page 455

    14 - 16 14. ABSOLUTE POSITION DET ECTION SYSTEM 3) ABS transfer mode finish-time time-out check If the ABS transfer mode (ABSM) is not turned OFF within 5s after the last ABS transmission data ready (19th signal for ABS data transmission) is tur ned ON, it is regarded as the transmission error and the ABS time-out warning (AL.E5) is output. OFF ON ...

  • Mitsumi electronic MR-J3- A - page 456

    14 - 17 14. ABSOLUTE POSITION DET ECTION SYSTEM 5) Servo-on (SON) OFF, Re set (RES) ON, Emer gency stop (EMG) OFF check d uring the ABS transfer When the ABS transfer mode is turned ON to start tran sferring and then the servo-on (SON) is turned OFF, the reset (RES) is turned ON, or the emer gency stop (EMG) is turned ON before the 19th ABS transmi ...

  • Mitsumi electronic MR-J3- A - page 457

    14 - 18 14. ABSOLUTE POSITION DET ECTION SYSTEM (b) Checksum error If the checksum error occurs, the programmable co ntroller should retry trans mission of the ABS data. Using the ladder check program of the pr ogramm able controller, turn OFF the ABS transfer mode (ABSM). After a lapse of 10ms or longer, turn OFF the servo-on (SON) (OFF time shoul ...

  • Mitsumi electronic MR-J3- A - page 458

    14 - 19 14. ABSOLUTE POSITION DET ECTION SYSTEM (3) At the time of alarm reset If an alarm occurs, turn OFF the servo-o n (SON) by detecting the a larm output (ALM). If an alarm has occurred, the ABS trans fer mode (ABSM) cannot be accepted. In the reset state, the ABS tr ansfer mode (ABSM) can be inpu t. OFF ON OFF ON OFF ON OFF ON OFF ON 95[ms] O ...

  • Mitsumi electronic MR-J3- A - page 459

    14 - 20 14. ABSOLUTE POSITION DET ECTION SYSTEM (4) At the time of emergenc y stop reset (a) If the power is switched ON in the emergency stop state The emergency stop state can be reset wh ile the ABS data is being transferred. If the emergency stop state is reset while the ABS data is transmitted, the base circuit is turned O N 95[ms] after reset ...

  • Mitsumi electronic MR-J3- A - page 460

    14 - 21 14. ABSOLUTE POSITION DET ECTION SYSTEM (b) If emergency stop is activated during servo-on The ABS transfer mode (ABSM) is permissible while in the emergency stop state. In th is case, the base circuit and the ready (RD) are turned ON after the emergency stop state is reset. OFF ON OFF ON OFF ON OFF ON OFF ON 95[ms] OFF ON OFF ON Servo-on ( ...

  • Mitsumi electronic MR-J3- A - page 461

    14 - 22 14. ABSOLUTE POSITION DET ECTION SYSTEM 14.9.3 Home position setting (1) Dog type home position return Preset a home position return creep s peed at which the machine will not be given impact. On detection of a zero pulse, the home position setting (CR) is turned fr om of f to on. At the same t ime, the s ervo amplifier clears the droop pul ...

  • Mitsumi electronic MR-J3- A - page 462

    14 - 23 14. ABSOLUTE POSITION DET ECTION SYSTEM (2) Data set type home position return POINT Never make home position settin g during co mmand operatio n or servo motor rotation. It may cause home position sift. It is possible to execute data set type home position return when the servo off. Move the machine to the position where the home pos ition ...

  • Mitsumi electronic MR-J3- A - page 463

    14 - 24 14. ABSOLUTE POSITION DET ECTION SYSTEM 14.9.4 Use of servo motor with an ele ctromagnetic brake The timing charts at power on/off and servo-on (SON) on/off are given below. Preset parameter No.PA04/ PD13 to PD1 6/PD18 of the servo a mplifier to make the electromag netic brake interlock (MBR) valid. When the ABS transfer mode is ON, the ele ...

  • Mitsumi electronic MR-J3- A - page 464

    14 - 25 14. ABSOLUTE POSITION DET ECTION SYSTEM 14.9.5 How to process the absol ute posi tion data at detection of stroke end The servo amplifier stops the acceptance of the command pulse when stroke end (LSP LSN) is detected, clears the droop pulses to 0 at the same time, and stops the servo motor rapidly. At this time, the programmable c ontrolle ...

  • Mitsumi electronic MR-J3- A - page 465

    14 - 26 14. ABSOLUTE POSITION DET ECTION SYSTEM 14.10 Examples of use 14.10.1 MELSEC FX (2N) -32MT (FX (2N) -1PG) (1) Connection diagram (a) FX-32MT (FX-1PG) 46 SD SD 24 3.3k 3.3k SG Servo al arm ABS communic ation error ABS checksum error ABSB0 22 ABSB1 23 ABST 25 ALM 48 RD 49 X0 X1 X2 24VDC RA2 FX-32MT L N COM RUN X3 X4 X5 X6 X7 X10 X11 X12 X15 X ...

  • Mitsumi electronic MR-J3- A - page 466

    14 - 27 14. ABSOLUTE POSITION DET ECTION SYSTEM (b) FX 2N -32MT (FX 2N -1PG) 46 SD SD 24 3.3k 3.3k Servo al arm ABS communica tion error ABS checksu m error ABSB0 22 ABSB1 23 ABST 25 ALM 48 RD 49 X0 X1 X2 24VDC RA2 FX 2N -32MT L N COM X3 X4 X5 X6 X7 X10 X11 X12 X15 X13 X14 Power suppl y Alarm rese t Emergency stop Servo-on JOG( ) JOG( ) Position st ...

  • Mitsumi electronic MR-J3- A - page 467

    14 - 28 14. ABSOLUTE POSITION DET ECTION SYSTEM (2) Sequence program example (a) Conditions 1) Operation pattern ABS data transfer is made a s soon as the servo- on switch is turned on. After tha t, positioning operation is performed as shown below. 30000 0 0 address 3) 1) 2) Home position 30000 0 After the completion of ABS da ta transmissi on, JO ...

  • Mitsumi electronic MR-J3- A - page 468

    14 - 29 14. ABSOLUTE POSITION DET ECTION SYSTEM (b) Device list X input contact Y output contact X0 Transmission data bit 0 / completion of positioning Y0 Y1 Servo-on ABS transfer mode X1 Transmission data bit 1 / zero speed detection Y2 ABS request X2 Send ABS transmission data ready/ torque limit control Y3 Y4 (Note 2) Alarm reset Electromagnetic ...

  • Mitsumi electronic MR-J3- A - page 469

    14 - 30 14. ABSOLUTE POSITION DET ECTION SYSTEM (c) ABS data transfer program for X-a xis M8002 D24 K0 DMOV K1 K0 K3 K0 TO K1 K100000 K4 K0 DTO K1 K10000 K7 K0 DTO K1 K50000 K9 K0 DTO K1 K1000 K11 K0 TO K1 K2 K12 K0 TO K1 D24 K13 K0 DTO K1 K200 K15 K0 TO K1 K100000 K19 K0 DTO 1 1 D100 K300000 DMOV D102 K 250000 DMOV D104 K0 DMOV Z K0 DMOV D4 K4 DMO ...

  • Mitsumi electronic MR-J3- A - page 470

    14 - 31 14. ABSOLUTE POSITION DET ECTION SYSTEM X6 M6 M5 SET M5 Y12 X6 Y0 Y12 1 1 2 2 M64 M62 ZRST M1 PLS C1 RST C2 C0 ZRST M99 RST M5 RST Y1 RST Y2 RST M6 RST Serv o-on r eques t Servo-on output ABS data t ransmissio n start Clearing retry counter Resetti ng read y to sen d ABS data Resetting servo-on request Resetting ABS transfer mode Resetting ...

  • Mitsumi electronic MR-J3- A - page 471

    14 - 32 14. ABSOLUTE POSITION DET ECTION SYSTEM X4 M0 Y3 Y3 C1 RST M64 M0 ZRST X5 X3 M1 2 2 3 3 D3 D0 ZRST C2 RST C0 RST M0 Y10 Y1 RST Y2 RST M99 RST M5 RST M6 RST Y1 SET M64 M10 ZRST D2 D0 ZRST C2 RST C0 RST Alarm reset output Clearing retry counter Clearing ABS data receiving area Clearing ABS receive data buffer Resetting ABS data rec eption cou ...

  • Mitsumi electronic MR-J3- A - page 472

    14 - 33 14. ABSOLUTE POSITION DET ECTION SYSTEM Y1 X2 M3 PLS M3 Y2 X2 C2 C2 C0 M64 3 3 D3 K2 M52 MOV Y2 SET K1M10 H0003 K1X0 WANDP K2 K38 M20 M10 SFTR D2 D2 K1M10 ADDP K16 C0 K19 Y2 RST Y1 RST D2 D2 H003F WANDP M62 D2 K2 M52 CMPP C1 M62 C1 Y12 M2 PL S T211 K2 M6 SE T M4 PL S ABS data 32 bits (2 bits 16 times) Checks um 6 bits (2 bits 3 t imes) Dete ...

  • Mitsumi electronic MR-J3- A - page 473

    14 - 34 14. ABSOLUTE POSITION DET ECTION SYSTEM M63 D0 K8 M20 DMOVP D0 D24 D0 DA DDP K1 D0 K26 K0 DTOP M99 SET Y11 X6 Y1 T201 Y1 Y2 Y1 X2 T201 T202 T203 M2 T200 M6 4 4 5 5 M64 M62 ZRST M6 RST Y1 RST Y2 RST K500 T202 K100 T203 K100 Y11 C1 D4 M5 SET Writing a bsolute position data to 1PG Detecting ABS communication error ABS transfer retry contr ol A ...

  • Mitsumi electronic MR-J3- A - page 474

    14 - 35 14. ABSOLUTE POSITION DET ECTION SYSTEM M8000 M109 X7 X12 M99 M120 PL S X10 JOG X11 JOG X7 X14 M120 K1 D100Z K17 K0 DTO M121 K6 Z DCMP M122 INDX 6 Z K0 DMOV X13 M0 X16 5 5 6 6 M110 M111 M112 M102 M103 M104 M105 M106 108 SET Z DINC Z DINC M101 M100 (Note) 1PG control command (not us ed) Operation command control Position command control Star ...

  • Mitsumi electronic MR-J3- A - page 475

    14 - 36 14. ABSOLUTE POSITION DET ECTION SYSTEM M8000 K1 K4M100 K25 K0 TO M200 K1 K3M200 K28 K0 FROM K1 D106 K26 K0 DFROM M108 RST END 6 6 FX2 1PG Transm ission of control sig nals 1PG FX2 Transmissi on of status 1PG FX2 Transm issio n of pres ent position D106, D107 1PG Resetting sta rt command (Continued from preceding pag e) Normally ON (d) Data ...

  • Mitsumi electronic MR-J3- A - page 476

    14 - 37 14. ABSOLUTE POSITION DET ECTION SYSTEM (e) Electromagnetic brake output During ABS data transfer (for several seconds after the servo-on (SON) is turned o n), the servo motor must be at a stop. Set " 1" in parameter No.PA04 of the servo amp lifie r to make the e lectromagnetic brake interloc k (MBR) valid. Y1 X1 Y4 Electromagneti ...

  • Mitsumi electronic MR-J3- A - page 477

    14 - 38 14. ABSOLUTE POSITION DET ECTION SYSTEM 14.10.2 MELSEC A1SD75 (1) Connection diagram PULSE F 600mA PULSE F PULSE R PULSE R ABS tran smission d ata bit 0 /Comple tion of po sitioning ABS transm ission data bit 1/Zero spe ed detecti on ABS transmi ssion data ready/Torque limit contr ol speed Trouble Alarm r eset Emergency stop Operating statu ...

  • Mitsumi electronic MR-J3- A - page 478

    14 - 39 14. ABSOLUTE POSITION DET ECTION SYSTEM Note 1. For the dog type home position return. Nee d not be connected for the data set t ype home position return. 2. If the s ervo motor p rovided with the zero point signal is st arted, the A1SD75 will o utput the devia tion counter cl ear (CR) . Ther efore, do not connect the clear (CR) of the M R- ...

  • Mitsumi electronic MR-J3- A - page 479

    14 - 40 14. ABSOLUTE POSITION DET ECTION SYSTEM (b) Device list X input contact Y output contac t X20 ABS Transmission data bi t 0 / po sitio nin g Y30 Ser vo-on completion Y31 ABS trans fer mode X21 ABS Transmission data bit 1 / ze ro spee d Y32 ABS re quest detection Y33 Alarm res et X22 Reading to send ABS data / limitin g torque Y34 (Note 2) El ...

  • Mitsumi electronic MR-J3- A - page 480

    14 - 41 14. ABSOLUTE POSITION DET ECTION SYSTEM (c) ABS data transfer program for X a xis This sequence program example assumes the following conditions. Parameters of the A1SD75P1-S3 positio ning module 1) Unit setting :3 pulse (PLS) 2) Travel per pulse :1 1 pulse To select the unit other tha n the pulse, conversion in to the unit of the feed valu ...

  • Mitsumi electronic MR-J3- A - page 481

    14 - 42 14. ABSOLUTE POSITION DET ECTION SYSTEM X26 M13 SET M23 K1 D11 K 816 H0000 FROM D11 H0001 WAND M23 1 1 2 2 D11 K1 M24 PLS M13 M14 M16 X26 M8 RST M13 RST C0 RST C1 RST Y30 M5 PLS M13 M17 PLS M17 X24 M14 Y33 X25 Y33 X23 C2 RST M14 M8 RST M13 RST Y38 Servo-on control ABS transfer retry contro l Servo alarm detectio n, alarm r eset control Serv ...

  • Mitsumi electronic MR-J3- A - page 482

    14 - 43 14. ABSOLUTE POSITION DET ECTION SYSTEM M5 D0 K16 MOV M5 Y31 M26 2 2 3 3 D1 K3 MOV D2 K0 MOV D5 K0 MOV D9 K0 DMOV A0 K0 DMOV C0 RST C1 RST Y31 C0 C1 Y31 D3 DMOVP A0 K1 D8 FROMP H0000 K 5 M18 PLS M18 A0 K0 MOVP D8 H0001 WAND A1 H8000 WAND D4 NEG D4 K1 D3 NEG D4 K1 D8 K1 K0 D3 10) Initializing ABS data transmission counter Initializi ng check ...

  • Mitsumi electronic MR-J3- A - page 483

    14 - 44 14. ABSOLUTE POSITION DET ECTION SYSTEM M9 C0 C1 3 3 4 4 D5 K1X20 MOV D5 H0003 WAND A0 D5 WOR K2 ROR M10 PLS D1 M9 C0 D5 K1X20 MOV K2 DROR D2 D2 D5 C0 C1 C2 D5 H0003 WAND A0 D5 WOR D0 M11 PLS K10 RORP A0 H003F WAND M6 M7 D6 A0 MOV Y3A D2 A0 D2 A0 Reading checks um 6bits (2 bi ts 3 time s) Reading ABS data 32 bi ts (2 bits 16 times) Detectin ...

  • Mitsumi electronic MR-J3- A - page 484

    14 - 45 14. ABSOLUTE POSITION DET ECTION SYSTEM M11 M10 Y31 X22 M12 Y32 Y32 X22 T 200 4 4 5 5 Y32 RST M12 PLS Y32 SE T T200 K1 M9 M6 K1 D9 K0072 H00 00 DFROP D3 D3 K D*P D3 D9 D3 D P M6 M24 M8 SET K1 D3 K1154 H00 00 DTOP K1 K900 3 K1 150 H0000 TO Y10 SET Y10 X1 X4 XA Y10 RST 7) ABS request control Restoring abso lute position data. Writing absol ut ...

  • Mitsumi electronic MR-J3- A - page 485

    14 - 46 14. ABSOLUTE POSITION DET ECTION SYSTEM Y39 X26 Y31 T0 Y31 Y32 Y31 X22 T0 T1 T3 5 5 Y31 RST K50 T1 K10 T3 K10 Y39 M7 T201 C2 M16 T2 M9039 END M15 SET M16 SET C2 D7 T2 K1 M16 RST D110 A0 DMOV Detecting ABS communication error ABS transfer retry contr ol Resetting ABS transfer mode ABS transfer mode 5s timer ABS request response 1s tim er ABS ...

  • Mitsumi electronic MR-J3- A - page 486

    14 - 47 14. ABSOLUTE POSITION DET ECTION SYSTEM (d) X-axis program Do not execute the X-axis program while the ABS ready (M8) is off. M10 When "M10" (ready to send ABS data) switches on, the X-ax is start pr ogra m is execu ted by the X-axis start command. X-axis start progra m Positioning mode X-axis start command Ready to send ABS data ...

  • Mitsumi electronic MR-J3- A - page 487

    14 - 48 14. ABSOLUTE POSITION DET ECTION SYSTEM (f) Data set type home position return After jogging the machine to the position where the home position (e .g. 500) is to be set, choose the home position return mode and set the h ome position with the home position return start switch (X27) ON. After switching power on, rotate the servo motor mo re ...

  • Mitsumi electronic MR-J3- A - page 488

    14 - 49 14. ABSOLUTE POSITION DET ECTION SYSTEM (g) Electromagnetic brake output During ABS data transfer (for several seconds after the servo-on (SON) is turned o n), the servo motor must be at a stop. Set " 1" in parameter No.PA04 of the servo amp lifie r to make the e lectromagnetic brake interloc k (MBR) valid. Y31 X21 Y34 El ectro ma ...

  • Mitsumi electronic MR-J3- A - page 489

    14 - 50 14. ABSOLUTE POSITION DET ECTION SYSTEM (3) Sequence program - 2-axis control The following program is a r eference example for creation o f an ABS sequence program for the second axis (Y axis) using a single A1SD75 module. Create a program for the third axis in a similar manner. (a) Y-axis program Refer to the X-axis ABS se quence program ...

  • Mitsumi electronic MR-J3- A - page 490

    14 - 51 14. ABSOLUTE POSITION DET ECTION SYSTEM 14.10.3 MELSEC QD75 (1) Connection diagram QY40 QX40 Q02HCPU Q62P QD75D PULSE F 600mA PULSE F PULSE R PULSE R ABS tra nsmissi on data bit 0/Completi on of posi tioning ABS transmi ssion data bit 1/ Zero speed detection ABS transmi ssion data ready /Torque lim it control speed Trouble Alarm r eset Emer ...

  • Mitsumi electronic MR-J3- A - page 491

    14 - 52 14. ABSOLUTE POSITION DET ECTION SYSTEM Note 1. For the dog type home position return. Nee d not be connected for the data set t ype home position return. 2. For th e dog type home position return, connect a QD75 devia tion counter clearin g signal cabl e. For the data set type home position return, connect a cable to the output modul e of ...

  • Mitsumi electronic MR-J3- A - page 492

    14 - 53 14. ABSOLUTE POSITION DET ECTION SYSTEM (c) ABS data transfer program for X a xis Progra mmable controller ready QD75 error reset Retry fre quency se t (Set 3 times.) Error reset co mpletion flag Serv o-on r eques t Prepa ration completion reset Serv o-on r eques t reset Absolute positi on restoration start Retry fl ag set Ret ry coun ter r ...

  • Mitsumi electronic MR-J3- A - page 493

    14 - 54 14. ABSOLUTE POSITION DET ECTION SYSTEM Absolute position restoration start flag Absolute position restoration status reset Absolute position restoration output Erro r code st orage Absolute position resto ration dat a reception ABS communica tion error Sum chec k error detection Retry fl ag set Retry counter Retry wait timer Error detectio ...

  • Mitsumi electronic MR-J3- A - page 494

    14 - 55 14. ABSOLUTE POSITION DET ECTION SYSTEM (d) X-axis program Do not execute the X-axis program while the ABS ready (M10) is off. M10 When "M 10" (read y to send ABS data) sw itches on , the X -axis start progr am is execu ted by the X- axis start command. X-axis start progra m Positioning mode X-axis start command Ready to send ABS ...

  • Mitsumi electronic MR-J3- A - page 495

    14 - 56 14. ABSOLUTE POSITION DET ECTION SYSTEM (f) Data set type home position return After jogging the machine to the position where the home position (e .g. 500) is to be set, choose the home position return mode and set the h ome position with the home position return start switch (X27) ON. After switching power on, rotate the s ervo motor more ...

  • Mitsumi electronic MR-J3- A - page 496

    14 - 57 14. ABSOLUTE POSITION DET ECTION SYSTEM (g) Electromagnetic brake output During ABS data transfer (for several seconds after the servo-on (SON) is turned o n), the servo motor must be at a stop. Set " 1" in parameter No.PA04 of the servo amp lifie r to make the e lectromagnetic brake interloc k (MBR) valid. Y31 X21 Y34 Electromagn ...

  • Mitsumi electronic MR-J3- A - page 497

    14 - 58 14. ABSOLUTE POSITION DET ECTION SYSTEM (3) Sequence program - 2-axis control The following program is a r eference example for creation o f an ABS sequence program for the second axis (Y axis) using a single QD75 module. Create a pro gram for the third axis in a similar manner. (a) Y-axis program Refer to the X-axis ABS se quence program a ...

  • Mitsumi electronic MR-J3- A - page 498

    14 - 59 14. ABSOLUTE POSITION DET ECTION SYSTEM 14.11 Absolute position dat a transfer errors 14.11.1 Corrective actions (1) Error list The number within parentheses in the table indicate s the output coil or input contact number of the A1SD75. Name Output coil Description Cause Action AD75 1PG (Note) ABS communication error Y39 Y11 1. The ABS data ...

  • Mitsumi electronic MR-J3- A - page 499

    14 - 60 14. ABSOLUTE POSITION DET ECTION SYSTEM (2) ABS communication error (a) The OFF period of the ABS transmission data ready si gnal outp ut from the servo amplifier is checked. If the OFF period is 1s or longer, this is re garded as a transfer fault a nd the ABS communication error is generated. The ABS communication error occurs if the ABS t ...

  • Mitsumi electronic MR-J3- A - page 500

    14 - 61 14. ABSOLUTE POSITION DET ECTION SYSTEM (c) To detect the ABS time-out warning (AL.E5) at the servo amplifier, the time required for the ABS request signal to go OFF a fter it has been turned ON (ABS re quest time) is checked. If the ABS request r emains ON for longer than 1s, it is regarded that an faul t relating to the ABS request signal ...

  • Mitsumi electronic MR-J3- A - page 501

    14 - 62 14. ABSOLUTE POSITION DET ECTION SYSTEM 14.12 Communication-bas ed ABS transfer system 14.12.1 Serial communication comman d The following commands are available for reading absol ute position data using the serial commu nication function. When reading data, take care to specify the co rrect station number of the drive unit fr om where the ...

  • Mitsumi electronic MR-J3- A - page 502

    14 - 63 14. ABSOLUTE POSITION DET ECTION SYSTEM (2) Transfer method The sequence in which the base circuit is turned ON (s ervo-on) when it is in the OFF state due to the servo-on (SON) going OFF, an emergency stop , or alar m, is explained below. In the absolute position detection system, a lways give the serial c ommunicati on command to read the ...

  • Mitsumi electronic MR-J3- A - page 503

    14 - 64 14. ABSOLUTE POSITION DET ECTION SYSTEM (c) At the time of alarm reset If an alarm has occurred, detect the trouble (ALM) an d turn off the servo-on (SON). After remo ving the alarm occurrence factor and deactivating the alarm, get the absolute position data again from the servo amplifier in accordance with the procedure in (a) of this sect ...

  • Mitsumi electronic MR-J3- A - page 504

    14 - 65 14. ABSOLUTE POSITION DET ECTION SYSTEM (d) At the time of forced sto p reset 210ms after the forced stop is deac tivated, the base circuit turns on, and further 5ms after that, the ready (RD) turns on. Always get the current position data from when the ready (RD) is triggered until before the position command is issued. 1) When power is sw ...

  • Mitsumi electronic MR-J3- A - page 505

    14 - 66 14. ABSOLUTE POSITION DET ECTION SYSTEM 14.13 Confirmation of absolute position detection data You can confirm the absolute position data with MR Configurator. Choose "Diagnostics" and "Absolute Encoder Data" to open the abs olute position data display sc reen. (1) Choosing "Diagnostics" in the menu o pens the ...

  • Mitsumi electronic MR-J3- A - page 506

    15 - 1 15. SERVO AMPLIFIERS WITH A LARGE CAPACITY (30k TO 55kW) 15. SERVO AMPLIFIERS WITH A LA RGE CAPACITY (30k TO 55kW) This chapter explains the MELSERVO-J3-A series AC servo featuring a large capacity o f 200V (30k to 37kW)/400V (30k to 55kW). Explanation made in this chapter is exclusively for the MR-J3-CR (4) converter units and the MR-J3-DU ...

  • Mitsumi electronic MR-J3- A - page 507

    15 - 2 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) 15.1.1 Function block diag ram The function block diagram of this servo is shown below. Current detection Voltage detec tion Regenerative TR MC Thyristor Power supply Control power supply L 11 L 21 L 1 L 2 L 3 CN1 I/F CHARGE lamp Regenerative optio n Converter Diode stack P 1 P 2 Co ...

  • Mitsumi electronic MR-J3- A - page 508

    15 - 3 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) Servo motor thermal Termination connector MR-J3-TM (Option) CN40 Drive unit Over current Control power supply Current detector (Note 1) Power supply L L L L CN40A CN40B Optional battery (For abs olute pos ition detection system) CN4 MR-J3BAT CN5 CN3 CN6 Analog monitor (2 channels) U ...

  • Mitsumi electronic MR-J3- A - page 509

    15 - 4 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) 15.1.2 Packing list Unpack the product and check the rating plate to see if the converter unit, drive unit and servo motor are as you ordered. (1) Converter unit POINT Regenerative resistor a nd power factor improving DC rea ctors are option. Purchase them separately if required. (R ...

  • Mitsumi electronic MR-J3- A - page 510

    15 - 5 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) 15.1.3 Standard specifications (1) Converter unit Converter unit Item MR-J3-CR 55K 55K4 Output Rated voltage 283 to 326VDC 538 to 678VDC Rated current [A] 215.9 113.8 Main circuit power supply Voltage, frequency 3-phase 200 to 230VAC, 50/60Hz 3-phase 380 to 480VAC, 50/60Hz Rated cur ...

  • Mitsumi electronic MR-J3- A - page 511

    15 - 6 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) (2) Drive unit (a) 200V class Drive unit Item MR-J3-DU 30KA 37KA Output Rated voltage 3-phase 170VAC Rated current [A] 174 204 Control power supply Voltage, frequency 1-phase 200 to 230VAC, 50/60Hz Rated current [A] 0.3 Permissible voltage fluctuation 1-phase 170 to 253VAC Permissib ...

  • Mitsumi electronic MR-J3- A - page 512

    15 - 7 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) (b) 400V class Drive unit Item MR-J3-DU 4 30KA 37KA 45KA 55KA Output Rated voltage 3-phase 323VAC Rated current [A] 87 102 131 143 Control power supply Voltage, frequency 1-phase 380 to 4 80VAC, 50/60Hz Rated current [A] 0.2 Permissible voltage fluctuation 1-phase 323 to 528VAC Perm ...

  • Mitsumi electronic MR-J3- A - page 513

    15 - 8 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) 15.1.4 Model definition (1) Rating plate Serial number POWER MITSUB ISHI AC SERVO MADE IN JA PAN MODEL MR-J3-CR55K MITSUBISHI E LECTRIC C ORPORATION AC SERVO PASSED Applicable power supply Capacity Model Rated output current : 55kW : : A5**** *** POWER : AC200V-230V 50/60Hz INPUT OU ...

  • Mitsumi electronic MR-J3- A - page 514

    15 - 9 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) 15.1.5 Combinations of converter u n its, drive unit and servo motors The following tables indicate the combinations of the converter units, driv e unit an d servo motors. (1) 200V class Converter unit Drive unit Servo motor HA-LP 1000r/min 1500r/min 2000r/min MR-J3-CR55K MR-J3-DU30 ...

  • Mitsumi electronic MR-J3- A - page 515

    15 - 10 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) 15.1.6 Parts identification (1) Converter unit (MR-J3-CR55K(4)) POINT The servo amplifier is shown with the terminal blo ck cover removed. For removal of the front cover, refer to section 15.1.7. Protective earth (PE) terminal ( ) Ground terminal. L L terminal (TE2-1) When using br ...

  • Mitsumi electronic MR-J3- A - page 516

    15 - 11 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) (2) Drive unit (MR-J3-DU30KA4 MR-J3-DU37KA4) POINT The servo amplifier is shown with the terminal blo ck cover removed. For removal of the front cover, refer to section 15.1.7. MODE UP DOWN SET Fixed part (4 pl ace) Coolin g fan Rating plate Display The 5-digit, seven-segment LED s ...

  • Mitsumi electronic MR-J3- A - page 517

    15 - 12 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) (3) Drive unit (MR-J3-DU30KA MR-J3-DU37KA MR-J3-DU45KA4 MR-J3-DU55KA4) POINT The servo amplifier is shown with the terminal blo ck cover removed. For removal of the front cover, refer to section 15.1.7. Rati ng pl ate Display The 5-digit, seven-segment LED shows the servo statu s a ...

  • Mitsumi electronic MR-J3- A - page 518

    15 - 13 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) 15.1.7 Removal and reinstallation of the terminal block cover CAUTION Before removing or installing the front cover, turn off the power and wait for 20 minutes or longer until the charge lamp turns off. Then, confirm that the voltage between L and L is safe with a voltage tester an ...

  • Mitsumi electronic MR-J3- A - page 519

    15 - 14 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) (b) How to reinstall th e terminal block cover A) B) C) D) 1) 2) Mounting screw 1) Put the ter minal block cover on and match the screw holes of the cover fit with those of the main unit. 2) Install the installing screws into the screw holes (A), B), C), D)). ...

  • Mitsumi electronic MR-J3- A - page 520

    15 - 15 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) (2) MR-J3-DU30KA4 or MR-J3-DU37KA4 (a) Upper terminal block cover 1) How to open A ) A)' Pull up the cover using the axis A), A)' as a support. When pulled up to the top, the cover is fixed. ...

  • Mitsumi electronic MR-J3- A - page 521

    15 - 16 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) 2) How to close Setting tab A) A)' Close the cover using the axis A), A)' as a support. Setting tab Press the cover against the terminal box until the installing knobs click. ...

  • Mitsumi electronic MR-J3- A - page 522

    15 - 17 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) (b) Lower terminal block cover 1) How to open Hold the bottom of the terminal block cover with both hands . B) B)' Pull up the cover using the axis B), B)' as a support. When pulled up to the top, the cover is fixed. ...

  • Mitsumi electronic MR-J3- A - page 523

    15 - 18 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) 2) How to close Setting tab Setting tab Hold the bottom of the terminal block cover with both hands . B) B)' Close the cover using the axis B), B)' as a support. Setting tab Press the cover against the terminal box until the installing knobs click. ...

  • Mitsumi electronic MR-J3- A - page 524

    15 - 19 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) 15.1.8 Servo system with auxiliary equip ment BV BW BU L 11 L 21 L 11 RS T 3-phase AC power supply (Not e 1) Communication cable Drive un it (No te 3) Converter unit (MR-J3CDL05M) Servo motor HA-LP series (Note 2) V U EW P 2 P 1 L 1 L 2 L 3 P C S R L 21 L Magnetic contactor operat ...

  • Mitsumi electronic MR-J3- A - page 525

    15 - 20 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) 15.2 Installation WARNING To prevent electric shock, ground each equipment securely. CAUTION Stacking in excess of the limited num ber of products is not allowed. Install the equipment to incombustibles. Installing them directly or clo se to combustibles will led to a fire. Install ...

  • Mitsumi electronic MR-J3- A - page 526

    15 - 21 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) 15.2.1 Installation direction and clearan ces CAUTION Install the equipment in the specified di rection. Not doing so can cause a failure. Leave the specified clearances between the converter unit/drive unit and the control box inside walls or other equipment. Not doing so can caus ...

  • Mitsumi electronic MR-J3- A - page 527

    15 - 22 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) 15.2.2 Inspection WARNING Before starting maintenance and/or inspection, turn off the power and wait for 20 minutes or longer until the charge lamp turns off. Then, confirm that the voltage between L and L is safe with a voltage tester and others. O therwise, an electric shock may ...

  • Mitsumi electronic MR-J3- A - page 528

    15 - 23 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) 15.3 Signals and wirin g WARNING Any person who is involved in wiring shou ld be fu lly competent to do the work. Before wiring, turn off the power and wait for 20 minutes or longer until the charge lamp turns off. Then, confirm tha t the voltage between L and L is safe with a volt ...

  • Mitsumi electronic MR-J3- A - page 529

    15 - 24 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) POINT Explanations on the following item are the sam e as those for servo amplifiers with 22kW or less. Refer to the section below for details. I/O signal connection example Refer to se ction 3.2. Signal (device) explanations Refer to section 3.5. Detailed description of the signal ...

  • Mitsumi electronic MR-J3- A - page 530

    15 - 25 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) (1) Enabling control function of m agnetic contactor (parameter No .PA02 1 (initial value)) Connecting the magnetic contactor contro l connector (CNP1) to the o perating coil of the magnetic contactor enables to control the magnetic contactor. Internal connection diag ram of CNP1 M ...

  • Mitsumi electronic MR-J3- A - page 531

    15 - 26 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) 15.3.2 Input power supply circuit WARNING Insulate the connections o f the power supply terminals. Not do ing so can cause an electric shock. Magnetic contactor wiring connector on the converter unit CNP1. Unattached state may cause an electric s hock. CAUTION Make sure to connect ...

  • Mitsumi electronic MR-J3- A - page 532

    15 - 27 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) (a) 200V class (MR-J3-DU30KA MR-J3-DU37KA) Regenerative option(Not e 1) RA3 RA1 RA2 OFF/ON Converter unit trou ble Servo mot or thermal relay Operation -ready Drive unit trou ble Emergenc y stop (EMG EM1) (Note 3) MC SK NFB MC (Note 5) (Note 4) Power supply BW BV BU Power factor im ...

  • Mitsumi electronic MR-J3- A - page 533

    15 - 28 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) (b) 400V class (MR-J3-DU30KA4 to MR -J3-DU55KA4) Emerge ncy stop (EMG EM1) (Note 3) RA3 RA1 RA2 OFF/ON MC SK MC (Not e 6) NFB (Note 3) RA2 (Note 4) Stepdown transformer L L L 1 L 2 L 3 L 11 L 21 3-phase 380 to 480VAC 50/60Hz 1 MC1 2 MC2 CN40 CN40A CN2 BW BV BU M OHS2 V U W CN40B V ...

  • Mitsumi electronic MR-J3- A - page 534

    15 - 29 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) (2) When magnetic contactor control connector (CNP1) is made inva lid POINT When making CNP1 invalid , set "0000" in parameter No.PA02. (Refer to section 15.5.) Make sure to connect a protection coo rdination cable (MR-J3CDL05 M) and a termination connector (MR-J3-TM ). W ...

  • Mitsumi electronic MR-J3- A - page 535

    15 - 30 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) (b) 400V class (MR-J3-DU30KA4 to MR -J3-DU55KA4) Emergency stop (EMG EM1) (Note 3) MC ON MC RA3 RA1 RA2 OFF SK (Not e 3) RA2 NFB MC (Not e 7) NFB L L L 1 L 2 L 3 L 11 L 21 1 MC1 2 MC2 CN40 CN40 CN2 BW BV BU M V U W CN40 V U W TE2-2 L L TE2-1 C L 11 L 21 PC PC S400 R400 PC S400 R400 ...

  • Mitsumi electronic MR-J3- A - page 536

    15 - 31 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) 15.3.3 Terminal Refer to section 15.7 for th e terminal block arrangement and signal layout. (1) Converter unit Connection target (Application) Abbreviation (Note) Terminal block Description MR-J3-CR55K MR-J3-CR55K4 Main circuit power supply L 1 L 2 L 3 TE1-1 Connect 3-phase 200 to ...

  • Mitsumi electronic MR-J3- A - page 537

    15 - 32 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) 15.3.4 How to use the connection ba rs Make sure to use the supplied c onnection conductors and connect the L and L of the converter unit to those of the drive un it as shown below. Never use co nnection conductors other than the ones supplied with the drive unit. Both units are sh ...

  • Mitsumi electronic MR-J3- A - page 538

    15 - 33 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) 15.3.5 Connectors and signal arran gements POINT The pin configurations of the conne ctors are as viewed from the cable connect or wiring section. (1) Converter unit CN6 Leave this open. CN40 Connect to CN40A of the drive unit. CN3 Leave this open. CHARGE CNP1 CN1 CN1 (Digital I/O ...

  • Mitsumi electronic MR-J3- A - page 539

    15 - 34 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) (2) Drive unit The drive unit front view shown is that of the MR -J3-DU30KA4, MR- J3-DU37KA4 or less. Refer to section 15.7 Outline Drawings for the appearances and connector layouts of the MR-J3- DU30KA, MR-J3-DU37KA, MR-J3-DU45KA4, MR-J3-DU55KA4. The frames of the CN2 and CN3 con ...

  • Mitsumi electronic MR-J3- A - page 540

    15 - 35 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) 15.3.6 Converter unit signa l (device) exp lanations POINT Explanations on the drive unit signals a re t he same as those for servo amplifiers with 22kW or less. Refer to section 3.5. (1) Signals For the I/O in terfaces (symbols in I/O column in the table), re fer to ( 2) in this s ...

  • Mitsumi electronic MR-J3- A - page 541

    15 - 36 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) (2) I/O interfaces (a) Digital input interface (DI) Give a signal with a relay or open collector transis tor. Refer to section 3.8.3 for source input. EM1 Conver ter u nit Switch Appr ox. 5mA For transisto r DICOM V CES 1.0V I CEO 100 A TR 24VDC 10 150mA Appro x. 5. 6k (b) Digital ...

  • Mitsumi electronic MR-J3- A - page 542

    15 - 37 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) 15.3.7 Timing chart (1) Power circuit timing chart Power-on procedure (a) Make sure to wire the power supply as shown in above section 15.3.1 using the magnetic contactor with the main circuit power supply (3-phase: L 1 , L 2 , L 3 ). Configure up an external sequence to switch off ...

  • Mitsumi electronic MR-J3- A - page 543

    15 - 38 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) (2) Alarm occurrence timing chart CAUTION When an alarm has occurred, remove its cause, make sure that the operation signal is not being input, en sure safety, and reset the a larm before restarting operation. As soon as an alarm occurs, make the Servo off sta tus and interrupt the ...

  • Mitsumi electronic MR-J3- A - page 544

    15 - 39 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) 2) Drive unit When an alarm occurs on the drive unit, the base circ uit is shut off and the servo motor coasts. When using an external dynamic brake (option), the e xter nal dynamic brake is acti vated to stop the servo motor. T o deactivat e the alarm, exe cute the foll owi ng: tu ...

  • Mitsumi electronic MR-J3- A - page 545

    15 - 40 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) (b) When controlling magnetic contactor by external seq uence 1) Converter unit When an alarm occurs on the converter unit, the servo-on turns OFF ; however, the main circuit power supply is not shut off. Ther efore, shut off the ma in circuit power supply by the external sequence. ...

  • Mitsumi electronic MR-J3- A - page 546

    15 - 41 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) 2) Drive unit When an alarm occurs in the drive unit, the drive uni t turns into the servo o ff but the main circuit power supply is not shut off. Therefore , shut off the main circuit power supply using the external sequence. Operation can be resumed b y turning the re set (RES) O ...

  • Mitsumi electronic MR-J3- A - page 547

    15 - 42 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) (3) Forced stop (EM1) ON/OFF timing chart (a) When control function of magnetic controller is enab led 1) Converter unit When the forced stop (EM1 ) is made valid in the c onverter unit, the magnetic contactor is turned off and the main circuit power supply is shut off. The drive u ...

  • Mitsumi electronic MR-J3- A - page 548

    15 - 43 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) 2) Drive unit When the Emergency stop (EMG) of the drive unit is activated, the base circuit shuts off in the operating drive unit, and the drive uni t goes into the emergency stop st atus. If the d rive unit becomes emergency stop status, the magnetic contactor turns o ff and the ...

  • Mitsumi electronic MR-J3- A - page 549

    15 - 44 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) (b) When turning off magnetic contactor by ex ternal sequence 1) Converter unit When the Forced stop (EM1) of the converter unit is activated, the base circuit shuts off in the operating drive unit, and the Main circuit off warning (AL.E9) is displayed on the drive unit. When the F ...

  • Mitsumi electronic MR-J3- A - page 550

    15 - 45 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) 2) Drive unit ON OFF ON OFF (3s) (3s) (Note 2) Dynamic brake Elec troma gnet ic brak e int erloc k (MBR ) Base circuit Servo motor speed Main circuit power supply Emergency stop (EMG) Invalid (ON) Valid (OFF) (Note 1) ON OFF a) Note 1. When setting up an electromagnetic brake at cu ...

  • Mitsumi electronic MR-J3- A - page 551

    15 - 46 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) CM10-R10P Encoder connector U V OHS2 BU W BW BV OHS1 Earth terminal M6 screw Motor power supply terminal block (U, V, W) M8 screw Cooling fan terminal block (BU, BV, BW) M4 screw Thermal sensor terminal bloc (OHS1, OHS2) M4 screw UV W BU BV BW OHS1 OHS2 Terminal block signal arrang ...

  • Mitsumi electronic MR-J3- A - page 552

    15 - 47 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) 15.4 Display section and o peration section of the converter unit 15.4.1 Display flowchart Use the display (3-dight, 7-segment L ED) on the front panel of the converter unit for status display, parame ter setting, etc. Set the parameters before operation, diagn ose an alarm, confir ...

  • Mitsumi electronic MR-J3- A - page 553

    15 - 48 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) 15.4.2 Status display mode The servo status during operation is shown on the 3-digit, 7-segmen t LED display. Press the "UP" or "DOWN" button to change displa y data as desired. When the required data is selected, the corresponding symbol is displayed . Press th ...

  • Mitsumi electronic MR-J3- A - page 554

    15 - 49 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) 15.4.3 Diagnostic mode (1) Diagnostic list Name Display Unit Sequence Not ready. Initializing. An alarm occurred. External forced stop status. Bus voltage is not established. Ready Indicates that the servo was switched on after completion of initialization and the drive unit is rea ...

  • Mitsumi electronic MR-J3- A - page 555

    15 - 50 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) (b) Display definition The LED segment corresponding to the pin is lit to in dicate ON, and is extinguished to indicate OFF. The 7-segment LED segments and CN1 connector pins correspond as shown below. Lit: ON Extin guished : OFF Input signals Output s ignals CN1-7: Forced stop (EM ...

  • Mitsumi electronic MR-J3- A - page 556

    15 - 51 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) 15.4.4 Alarm mode The current alarm and parameter error are displa yed. The lower 2 digits on the display indica te the alarm number that has occurred or the parameter number in error. Display example are shown below. Name Display Description Current alarm Indicates on occurrence o ...

  • Mitsumi electronic MR-J3- A - page 557

    15 - 52 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) Functions at occurrence of an alarm (1) Any mode screen displays the current alarm. (2) The other screen is visible during occurrence of an a lar m. At this time, the decimal point in the third digit flickers. (3) To clear any alarm, switch power off, then on or pre ss the "SE ...

  • Mitsumi electronic MR-J3- A - page 558

    15 - 53 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) 15.5. Parameters for converter unit CAUTION Never adjust or change the parameter values extremely as it will make operation instable. POINT Refer to chapter 5 for parameters for drive unit. The parameter whose symbol precede d by * can be validated with the following conditions: * ...

  • Mitsumi electronic MR-J3- A - page 559

    15 - 54 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) 15.5.2 List of details No. Symbol Name and function Initial value Unit Setting range PA01 *REG Regenera tive option Used to select the regenerative option. Select the regenerative option. 00: No used 01: M R-RB13 9 02: MR-R B137(3 p cs.) 11: MR-R B136-4 12: MR-R B138-4( 3 pcs.) &qu ...

  • Mitsumi electronic MR-J3- A - page 560

    15 - 55 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) No. Symbol Name and function Initial value Unit Setting range PA12 *DIF Input filter setting Select the input filter. Input signal filt er If external input signal cau ses chat tering due to noise, etc., input filter is used to suppress it. 0: None 1: 1.777[ms] 2: 3.555[ms] 3: 5.33 ...

  • Mitsumi electronic MR-J3- A - page 561

    15 - 56 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) (2) Remedies for alarms CAUTION When any alarm has occurred, eliminate i t s cause, ensure safety, then reset the alarm, and restart operation. Otherwise, injury ma y occur. POINT When any of the following alarms has occurred, al ways remove its cause and allow about 30 minutes for ...

  • Mitsumi electronic MR-J3- A - page 562

    15 - 57 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) Display Name Definition Cause Action A.30 Regenerative error Permissible regenerative power of regenerative option is exceeded. 1. Incorrect setting of parameter No.PA01. Set correctly. 2. Regenerative option is not connected. Connect correctly. 3. High-duty operation or continuous ...

  • Mitsumi electronic MR-J3- A - page 563

    15 - 58 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) Display Name Definition Cause Action A.38 MC drive circuit error Magnetic contactor drive circuit error (When the magnetic contactor is turned on: the main circuit power supply is not turned on within two seconds after the servo-on of the drive unit. When the magnetic contactor is ...

  • Mitsumi electronic MR-J3- A - page 564

    15 - 59 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) (3) Remedies for warnings Continuing operation in an alarm occurrence status ma y result in an alarm or disable proper op eration. Eliminate the cause of the warning according to this section. The warning displayed will disappear when the cause of its occurrence is resolved. Displa ...

  • Mitsumi electronic MR-J3- A - page 565

    15 - 60 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) 15.6.2 Drive unit POINT Explanation made in this section is exclusively for th e driver unit. Other troubleshooting is the same as th at for servo amplifiers with 22kW or less. Refer to chapter 9. As soon as an alarm occurs, make the Servo off statu s and interrupt the main circuit ...

  • Mitsumi electronic MR-J3- A - page 566

    15 - 61 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) (3) Remedies for warnings Continuing operation in an alarm occurrence status ma y result in an alarm or disable proper op eration. Eliminate the cause of the warning according to this section. The warning displayed will disappear when the cause of its occurrence is resolved. Indica ...

  • Mitsumi electronic MR-J3- A - page 567

    15 - 62 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) 15.7 Outline drawings POINT Refer to section 15.2.1 for outline dimen sion drawing. 15.7.1 Converter unit (MR-J3-CR5 5K(4)) [Unit: mm] 7 328 277 300 Approx. 200 180 20 Approx. 20 Approx. 80 260 128 TE1-2 TE2-2 TE3 TE1-1 TE1-2 TE1-1 TE3 TE2-2 PE CHARGE 2- 7 Installation hole Cooling ...

  • Mitsumi electronic MR-J3- A - page 568

    15 - 63 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) 15.7.2 Drive unit (1) MR-J3-DU30KA MR-J3-DU37KA MR-J3-DU45KA4 MR-J3-DU55KA4 [Unit: mm] TE2-1 PE TE2-1 20 260 Approx. 20 2- 7 Installation hole Approx. 200 300 180 Approx. 80 7 TE3 TE1 For mounting MR-J3BAT 328 Approx. 200 128 277 Terminal block layout (Terminal cover removed) TE1 T ...

  • Mitsumi electronic MR-J3- A - page 569

    15 - 64 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) (2) MR-J3-DU30KA4 MR-J3-DU37KA4 [Unit: mm] 2- 6Installation hole 240 Approx. 200 Approx. 200 328 128 180 Approx. 80 120 60 6 219.2 TE2 TE3 TE1 For mounting MR-J3BAT TE2 TE1 PE TE3 Approx. 60 Cooling fan exhaust Air intake Terminal block layout (Terminal cover removed) Mass: 18[kg] ...

  • Mitsumi electronic MR-J3- A - page 570

    15 - 65 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) 15.8 Characteristics 15.8.1 Overload protection characteri stics An electronic thermal relay is built in the converter unit and drive unit to protect the servo motor, converter unit, drive unit and servo motor p ower line from overloads. Overload 1 alarm (AL.50) occurs if overload ...

  • Mitsumi electronic MR-J3- A - page 571

    15 - 66 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) 15.8.2 Power supply equipment capacity and gene rated loss POINT The calculation method of heat dissipati on area for enclosed control panel i s the same as that for servo amplifiers with 22kW or less. Re fer to section 11. 2 (2). Table 15.1 indicates the ge nerated loss and power ...

  • Mitsumi electronic MR-J3- A - page 572

    15 - 67 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) 15.8.3 Dynamic brake characteristics POINT Dynamic brake operates at occurrence of alarm, se rv o emergency st op warning (AL.E6), and when power is turned off. Do not use dy namic brake to stop in a normal operation as it is the function to stop in em ergency. Maximum usage time o ...

  • Mitsumi electronic MR-J3- A - page 573

    15 - 68 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) (b) Dynamic brake time constant The following shows necessary dynamic brake time constant for the equations (1 5.1). 40 35 30 25 20 15 10 5 0 200 600 1 000 01 2 0 0 Speed [r/min] HA-LP30K1 HA-LP37K1 400 800 Time constant [ms] 40 35 30 25 20 15 10 5 0 200 600 100 0 01 2 0 0 Speed [r ...

  • Mitsumi electronic MR-J3- A - page 574

    15 - 69 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) 45 40 35 30 25 20 15 10 5 0 500 1000 1500 0 2000 HA-LP30K2 HA-LP37K2 Speed [r/min] Time constant [ms] 45 40 35 30 25 20 15 10 5 0 500 1000 1500 0 2000 HA-LP45K24 HA-LP55K24 HA-LP37K24 HA-LP30K24 Speed [r/min] Time constant [ms] HA-LP2000r/min series (2) Load to motor inertia moment ...

  • Mitsumi electronic MR-J3- A - page 575

    15 - 70 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) 15.8.4 Inrush currents at po wer-on of main circuit and control circuit The following table indica tes the inrush currents (refer ence data) that will flow when the maximum permissible voltage (200V class: 253VAC, 400V class: 528VAC) is applied at the power supply capacity of 2500k ...

  • Mitsumi electronic MR-J3- A - page 576

    15 - 71 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) (1) Makeup of cables and like The following shows the cable makeup for connection with the servo motor and other model. Drive unit Conver ter u nit CNP1 CN40 CN1 7) 8) 2) 1) CN40A CN40B CN2 3) 4) 5) 6) 9) Terminal box Servo motor HA-LP ...

  • Mitsumi electronic MR-J3- A - page 577

    15 - 72 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) No. Product Model Description Application 1) Protection coordination cable MR-J3CDL05M Refer to (2) in this section. Connector: 10120-3000PE Shell kit: 10320-52F0-008 (3M or equivalent) Connector: PCR-S20FS+ Case: PCR-LS20LA1 (Honda Tsushin Kogyo) 2) Connector set MR-J2CN1-A Refer ...

  • Mitsumi electronic MR-J3- A - page 578

    15 - 73 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) (2) MR-J3CDL05M(0.5m) Protection coordination cable CAUTION Connect protection coordinati on cables c orrectly if they are fabricate d. Otherwise, the system may perform unexpected operation. When fabricating a protection coordinat ion cable, fabricate the cable as s hown in the wi ...

  • Mitsumi electronic MR-J3- A - page 579

    15 - 74 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) 15.9.2 Regenerative option CAUTION The specified combinations of regenerativ e options, converter unit and drive unit may only be used. O therwise, a fire may occur. POINT The calculation method of regenerative ene rgy is the same as that for servo amplifiers with 22kW or less. Ref ...

  • Mitsumi electronic MR-J3- A - page 580

    15 - 75 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) (4) Connection of the regenerative op tion Make sure to supply 1-phase 200V and 4 00V respectively to the cooling f an. The cooling fan specifications are as follows. Table 15.3 Cooling fan Item 200V class 400V class Model MR-RB137 MR-RB139 MR-RB136-4 MR-RB138-4 Voltage Frequency 1 ...

  • Mitsumi electronic MR-J3- A - page 581

    15 - 76 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) (b) MR-RB137 MR-RB138-4 POINT Three of MR-RB137 or MR-RB1 38-4 ar e required per conve rter unit. Please purchase three of MR-RB137 or MR-RB 138-4. Regenerative option Cooling f an Regenerative option Servo mot or Servo motor thermal relay OHS1 OHS2 24VDC RA (Note 3) Power supply C ...

  • Mitsumi electronic MR-J3- A - page 582

    15 - 77 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) (5) Outline dimension drawings [Unit:mm] 260 230 2- 10 mounting hole 10 15 15 Cooling fan (Note 1) 15 230 15 197 Air intake 15 2.3 215 MR-RB139 MR-RB136-4 Mass [kg(lb)] 11(24.25) 10(22.05) Regenerative option R1 (Note 2) G4 G3 C P MR-RB137 MR-RB138-4 Terminal block signal layout TE ...

  • Mitsumi electronic MR-J3- A - page 583

    15 - 78 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) 15.9.3 External dynamic brake CAUTION Use an external dynamic brake for the dr ive unit. Failur e to do so will cause an accident because the servo motor does not stop immediately but co asts at an emergency stop and such conditions. Ensure the safety in the entire system. POINT Co ...

  • Mitsumi electronic MR-J3- A - page 584

    15 - 79 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) MC RA2 External dynamic brake 24VDC RA1 RA3 (Note 4) RA2 L 1 L 2 L 3 L 11 L 21 U V W U V W M Servo motor (Note 3) Power supply L L L L L L L 11 L 21 L L Drive unit Conver ter unit (Note 1) 1 MC1 2 MC2 CNP1 15 SON 42 EMG 46 DOCOM SD Plate CN1 (Note 2) DB 20 DICOM 47 DOCOM ALM 48 CN1 ...

  • Mitsumi electronic MR-J3- A - page 585

    15 - 80 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) (3) Outline dimension drawing [Unit:mm] 390 370 10 10 260 230 15 15 10 15 15 230 30 330 30 220 15 235 2- 10 i nstallati on hole 2.3 TE2 TE1 Terminal block TE1 Terminal s crew: M5 Tightening torque: 2.0 [N m] (17.7 [lb in]) Mounting screw Screw size: M8 Tightening torque: 13.2 [N m] ...

  • Mitsumi electronic MR-J3- A - page 586

    15 - 81 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) 15.9.4 Selection example of wires POINT Wires indicated in this section are separated wi res. When using a cable for power line (U, V, and W) between the dr ive unit and servo motor, use a 600V grade EP rubber insulated chloroprene sheath cab-tire cable (2PNCT). For selection of ca ...

  • Mitsumi electronic MR-J3- A - page 587

    15 - 82 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) (1) When using the 600V Polyvinyl chloride insulated wire (IV wire) Selection example of wire s ize when using IV wires is indicated be low. Table 15.4 Wire size select ion example 1 (IV wire) Converter unit (Note 2) Drive unit Wires[mm 2 ] (Note 1, 3) 1) L 1 L 2 L 3 2) L 11 L 21 3 ...

  • Mitsumi electronic MR-J3- A - page 588

    15 - 83 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) (3) Selection example of crimping terminals The table below shows a selection example of crimpin g terminals for the servo amplifier terminal block when using the wires mentioned in (1) an d (2) in this section. Symbol Servo amplifier side crimping terminals (Note 2) Crimping termi ...

  • Mitsumi electronic MR-J3- A - page 589

    15 - 84 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) 15.9.6 Power factor improving DC reactor The input power factor is improved to about 95 . Converter unit Drive unit Power factor improving DC reactor Dimension [mm] Terminal screw Mass [kg (lb)] W D H W1 X MR-J3-CR55K MR-J3-DU30KA MR-DCL30K 135 255 215 80 232 M12 9.5 (20.94) MR-J3- ...

  • Mitsumi electronic MR-J3- A - page 590

    15 - 85 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) 15.9.7 Line noise filter (FR-BLF) POINT This section explains ho w to use the line noise filter unique to servo amplifiers with a large capacity. Other noise reduct ion produ cts are the same as those for servo amplifiers with 22kW or less. Re fer to section 12.17. This filter is e ...

  • Mitsumi electronic MR-J3- A - page 591

    15 - 86 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) 15.9.8 Leakage cu rrent breaker (1) Selection method High-frequency chopper currents controlled by pulse width modulation flow in the AC servo circuits. Leakage currents containing harmonic contents are larger than those of the motor which is run with a commercial power supply. Sel ...

  • Mitsumi electronic MR-J3- A - page 592

    15 - 87 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) (2) Selection example Indicated below is an example o f selecting a leakage current breaker under the following conditions. NV 22mm 2 5m 30mm 2 5m M Ig1 Ig2 Igm Conv erter unit Drive unit Iga Servo motor Use a leakage current breaker designed for suppressing harmonics/surges. Find ...

  • Mitsumi electronic MR-J3- A - page 593

    15 - 88 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) 15.9.9 EMC filter (recommended) For compliance with the EMC directive of the IEC/EN Standard, it is recommended to use the following filter. Some EMC filters are large in leakage current. (1) Converter unit Drive unit Converter unit Drive unit Recommended filter (Soshin Electric) M ...

  • Mitsumi electronic MR-J3- A - page 594

    15 - 89 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) (3) Outline drawing HF3200A-UN [Unit: mm] 500 5 480 1 3- 6.5 3-M10 M8 3- 6.5 Length: 8 TF3150C-TX [Unit: mm] 150 1 150 1 150 1 452 5 500 3 3-M8 3-M8 M4 M8 M4 M4 8-R 4.25 Length: 12 (for M8) 110 2 210 2 (227) 260 3 ...

  • Mitsumi electronic MR-J3- A - page 595

    15 - 90 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) 15.9.10 FR-BU2-(H) bra ke unit POINT Use a 200V class brake unit and a resist or unit with a 200V class converter unit, and a 400V class brake unit and a re sistor unit with a 400V class converte r unit. Combination of different voltage class un its cannot be used. Install a brake ...

  • Mitsumi electronic MR-J3- A - page 596

    15 - 91 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) (2) Brake unit parameter setting Normally, changing parameters of the FR-BU2-(H) is not necessary. Whether a parameter can be changed or not is listed below. Parameter Change possible/ impossible Remarks No. Name 0 Brake mode switchover Impossible Do not change the parameter. 1 Mon ...

  • Mitsumi electronic MR-J3- A - page 597

    15 - 92 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) B C B C MC (Note 1) Power supply Drive unit Converter u nit L 1 L 2 L 3 L 11 L 21 L L L L 1 MC1 2 MC2 CNP1 CN1 1 DICOM 5 DOCOM 6 DICOM 2A L M 7E M 1 9 DOCOM (Note 2) RA2 FR-B R-(H) P PR TH2 TH1 (Note 6) Terminal block (Note 12) A L 11 L 21 (Not e 5) P 1 P 2 (Not e 3) L L (Note 9) C ...

  • Mitsumi electronic MR-J3- A - page 598

    15 - 93 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) Note 1. For power suppl y specific ations, refer to section 15.1.3. 2. Make up a sequence that will concurrently turn off the Em ergency stop (EMG) of the drive unit and the Forced stop (EM1) of t he converter unit, and shut off the main circuit power supply by the external sequenc ...

  • Mitsumi electronic MR-J3- A - page 599

    15 - 94 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) (b) Combination with MT-BR5-(H) resistor unit 1) When connecting a brake unit to a con verter unit RA3 RA1 RA2 OFF/ON Converter unit trou ble Operation ready Drive unit trouble Emergency stop (EMG EM 1) (Not e 2) (Note 8) Servo motor thermal relay MC RA5 SK Drive unit Converter u n ...

  • Mitsumi electronic MR-J3- A - page 600

    15 - 95 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) 2) When connecting two brake units to a converter unit POINT To use brake units with a parallel co nnect ion, use two sets of FR-BU2-(H) bra ke unit. Combination with other brake unit results in al arm occurrence or malfunction. Make sure to connect the master and sl ave terminals ...

  • Mitsumi electronic MR-J3- A - page 601

    15 - 96 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) RA3 RA1 R A2 OFF/ON Conv erte r unit trouble Operation ready Drive unit trouble Emerge ncy stop (EMG EM1) (Not e 2) (Not e 8) Servo motor thermal relay MC RA4 RA5 SK Drive unit Conv erter unit L 1 L 2 L 3 L 11 L 21 (Not e 1) Power supply L L L L 1 MC1 2 MC2 CNP1 L 11 L 21 (Note 5) ...

  • Mitsumi electronic MR-J3- A - page 602

    15 - 97 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) Note 1. For power suppl y specific ations, refer to section 15.1.3. 2. Make up a sequence that will concurrently turn off the Em ergency stop (EMG) of the drive unit and the Forced stop (EM1) of t he converter unit, and shut off the main circuit power supply by the external sequenc ...

  • Mitsumi electronic MR-J3- A - page 603

    15 - 98 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) b) Control circuit terminal POINT Undertightening ca n cause a cable disco nne ction or malfunction. Overtightening can cause a short circuit or malfun ction due to damage to the screw or the b rake unit. A RES PC B SD BUE C MSG SD MSG SD SD Jumper Terminal block 6mm Sheath Core Wi ...

  • Mitsumi electronic MR-J3- A - page 604

    15 - 99 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) (e) Crimping terminals for L and L terminals of TE2-1 of servo amplifier 1) Recommended crimping terminals POINT Make sure to use recomme nded crimping terminals or equivalent since some crimping terminals cannot be installed depending o n the size. Converter unit Brake unit Number ...

  • Mitsumi electronic MR-J3- A - page 605

    15 - 100 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) (4) Outline dimension drawings (a) FR-BU2- (H) brake unit [Unit: mm] FR-BU2-55K FR-BU2-H55K, H75K 18.5 Rating plate 52 72 5 142.5 5 6 158 6 170 2- 5hole (Screw size: M4) (b) FR-BR- (H) resistor unit [Unit: mm] 2- C Control circuit terminal Main circuit terminal W1 1 Approx. 35 App ...

  • Mitsumi electronic MR-J3- A - page 606

    15 - 101 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) (c) MT-BR5- (H) resistor unit [Unit: mm] 4 15 mounting hole 300 75 75 450 7.5 7.5 M6 M4 193 189 480 510 37 60 21 10 NP Resistor unit Resistance value Approximate mass [kg] ([lb]) 200V class MT-BR5-55K 2.0 50 (110 ) 400V class MT-BR5-H75K 6.5 70 (154) ...

  • Mitsumi electronic MR-J3- A - page 607

    15 - 102 15. SERVO AMPLIFIERS WI TH A LARGE CAPACITY ( 30k TO 55kW ) MEMO ...

  • Mitsumi electronic MR-J3- A - page 608

    16 - 1 16. PARAMETER UNIT ( MR-PRU03 ) 16. PARAMETER UNIT (MR-PRU03) POINT Do not use MR-PRU03 parameter u nit and MR Configurator together. Perform simple data setting, test opera tion, parameter setting , etc. without MR Configurator by connecting the MR-PRU03 parameter unit to the servo a mplifier (drive unit). ...

  • Mitsumi electronic MR-J3- A - page 609

    16 - 2 16. PARAMETER UNIT (MR-P RU03) 16.1 External appearance and key explanation s This section gives the exter nal appearance and explanations o f the keys. PRU03 MON DATA PARAM ALM/ DGN TEST Fn SHIFT ESC 7 89 DE F 4 5 6 A BC 123 0 1STEP STOP RESET REV FWD Key MON DATA PARAM ALM/ DGN TEST Fn SHIFT ESC 0 9 F STOP RESET REV FWD 1STEP Key explanati ...

  • Mitsumi electronic MR-J3- A - page 610

    16 - 3 16. PARAMETER UNIT (MR-P RU03) 16.2 Specifications Item Description Model MR-PR U03 Power supply Supplied from the servo amplifier (drive unit) Functions Parameter mode Basic setting parameters, Gain/filt er parameters, Extension setting parameters, I/O setting parameters Monitor mode (Status display) Cumulative command pulses, Command pulse ...

  • Mitsumi electronic MR-J3- A - page 611

    16 - 4 16. PARAMETER UNIT (MR-P RU03) 16.4 Connection with servo amplifier 16.4.1 Single axis (1) Configuration diagram Operate the single-axis servo amplifier (drive uni t). It is recommended to use the following cable. PRU03 MON DATA PARAM ALM/ DGN TEST Fn SHIFT ES C 7 8 9 D EF 4 5 6 A B C 1 23 0 1STEP STOP RESET REV FWD Parameter unit (MR-PRU03) ...

  • Mitsumi electronic MR-J3- A - page 612

    16 - 5 16. PARAMETER UNIT (MR-P RU03) 16.4.2 Multidrop connection (1) Configuration diagram Up to 32 axes of servo amplifiers (drive units) fr om s tations 0 to 31 can be opera ted on the same bus. ( Note 3 ) (Note 2) Servo a mplifie r (drive u nit) Servo am plifier (drive unit) Servo a mplifie r (drive unit) (Note 2) (Note 1) (Note 2 ) (Note 1) (N ...

  • Mitsumi electronic MR-J3- A - page 613

    16 - 6 16. PARAMETER UNIT (MR-P RU03) (2) Cable internal wiring dia gram Wire the cables as shown below. Para mete r unit 7 1 2 3 4 5 6 8 7 1 2 3 4 5 6 8 12345678 7 1 2 3 4 5 6 8 (Not e 4, 5) LG P5D RDP SDN SDP RDN LG NC (Note 5) (Note 1) Axis 1 servo amplifier (drive unit) CN3 connector (RJ45 c onnec tor) 7 1 2 3 4 5 6 8 7 1 2 3 4 5 6 8 12345678 7 ...

  • Mitsumi electronic MR-J3- A - page 614

    16 - 7 16. PARAMETER UNIT (MR-P RU03) 16.5 Display Connect the MR-PRU03 parameter unit to the servo amplifie r (drive unit), and turn ON the power of the servo amplifier (drive unit). In this section, the s creen tr ansition of the MR-PRU03 param eter un it is explained, together with the operati on procedure in each mode. 16.5.1 Outline of screen ...

  • Mitsumi electronic MR-J3- A - page 615

    16 - 8 16. PARAMETER UNIT (MR-P RU03) 16.5.2 MR-PRU03 parameter unit setting Set and enter the station number. (e.g. To enter 31th axis) Stati on numb er Contrast adjustment Buzzer Baud rate selection 3 1 ESC MR-PRU03 parameter unit setting Press the " " keys to select, and press the " " key to set. Press the " " keys ...

  • Mitsumi electronic MR-J3- A - page 616

    16 - 9 16. PARAMETER UNIT (MR-P RU03) 16.5.3 Monitor mode (status display) (1) Monitor display The servo status during operation is shown on the disp lay . Refer to (2) in this section for details. 24. F or manu fact urer s etti ng 1. Cumulative feedback pulse 2. Servo motor speed 3. Droop pulse 4. Cumulative command pulse 5. Command pulse frequenc ...

  • Mitsumi electronic MR-J3- A - page 617

    16 - 10 16. PARAMETER UNIT (MR-P RU03) (2) Monitor display list The following table lis ts the items and des criptions of monitor displa y. Status display Display on parameter unit Unit Description Display range Cumulative feedback pulses Pulse F/B pulse Feedback pulses from the servo motor encoder are counted and displayed. When the value exceeds ...

  • Mitsumi electronic MR-J3- A - page 618

    16 - 11 16. PARAMETER UNIT (MR-P RU03) Status display Display on parameter unit Unit Description Display range Within one-revolution position Cyc posit pulse Position within one revolution is displayed in encoder pulses. The value returns to 0 when it exceeds the maximum number of pulses. The value is incremented in the CCW direction of rotation. 0 ...

  • Mitsumi electronic MR-J3- A - page 619

    16 - 12 16. PARAMETER UNIT (MR-P RU03) 16.5.4 Alarm/diagnostic mode (1) Alarm display The flowchart below shows the procedure of settings in volving alarms, alarm his t ory, external I/O signal (DIDO) display, device and diagnosis. ALM/ DGN STOP RESET Alarm Current alarm (When undervoltage (AL.10) occurred.) Alar m hist ory Motor inform ation Total ...

  • Mitsumi electronic MR-J3- A - page 620

    16 - 13 16. PARAMETER UNIT (MR-P RU03) (2) Alarm history clear The servo amplifier stores one current ala rm and five pa st alarms from when its power is switched on first. To control alarms which will occur during operation, cle ar the alarm history before starting operation. ALM/ DGN STOP RESET 1) Select "ALM Hist". For six alar ms incl ...

  • Mitsumi electronic MR-J3- A - page 621

    16 - 14 16. PARAMETER UNIT (MR-P RU03) 16.5.5 Parameter mode The flowchart below shows the procedure for setting pa rameters. DATA PARAM Sele ct a par ameter gr oup. First parameter number is displayed. e.g. To select the gain/filter para meter, press: Write Write is c ompleted. The following message appears if swit ching power of f or on is needed ...

  • Mitsumi electronic MR-J3- A - page 622

    16 - 15 16. PARAMETER UNIT (MR-P RU03) 16.5.6 Test operation mode CAUTION When confirming the machine operation in the test operation mode, use the machine after checking that the safety mechanism such as the emerg ency stop (EMG) operates. If any operational fault has occurred, stop operation us ing the emergency stop (EMG). POINT The test operati ...

  • Mitsumi electronic MR-J3- A - page 623

    16 - 16 16. PARAMETER UNIT (MR-P RU03) (1) JOG operation JOG operation can be performed when there is no command from the external c ommand device. Connect EMG-DOCOM to start JOG operation. (a) Operation/cancel You can change the operation conditions with the par ameter unit. The initia l conditions and setting ranges for operation are listed below ...

  • Mitsumi electronic MR-J3- A - page 624

    16 - 17 16. PARAMETER UNIT (MR-P RU03) (2) Positioning operation Positioning operation can be performed once when there is no command from the external command device. Connect EMG-DOCOM to start positioning operation. (a) Operation/cancel You can change the operation conditions with the par ameter unit. The initia l conditions and setting ranges fo ...

  • Mitsumi electronic MR-J3- A - page 625

    16 - 18 16. PARAMETER UNIT (MR-P RU03) If the communication cable is d isconnected during posit ioning opera tion, the servo motor will come to a sudden stop. (b) Status display You can monitor the status displa y even during positioning opera tion. At this time, the "FWD", "REV" and "STOP" keys can be used. (3) Motor- ...

  • Mitsumi electronic MR-J3- A - page 626

    16 - 19 16. PARAMETER UNIT (MR-P RU03) 16.6 Error message list When using the MR-PRU03 parameter un it, the following error messages may be displayed. When displayed, refer to this section to remove cause. (1) Error messages Error description Message Cause Communication error 1. Hardware reason 2. Mismatch in station number 3. Mismatch in baud rate ...

  • Mitsumi electronic MR-J3- A - page 627

    16 - 20 16. PARAMETER UNIT (MR-P RU03) MEMO ...

  • Mitsumi electronic MR-J3- A - page 628

    App. - 1 A PPENDIX App. 1 Parameter list POINT For any parameter whose symbol i s preceded by *, set the parameter value and switch power off once, then switch it on again to make that parameter setting valid. App. 1.1 Servo amplifier (drive unit) Basic setting parameters (PA ) Gain/filter parameters (PB ) No. Symbol Name Control mode No. Symbol Na ...

  • Mitsumi electronic MR-J3- A - page 629

    App. - 2 A PPENDI X Extension setting parameters (PC ) Extension setting paramete rs (PC ) No. Symbol Name Control mode No. S ymbol Name Control mode PC01 STA Acceleration time constant S T PC39 MO1 Analog monitor 1 offset P S T PC02 STB Deceleration time constant S T PC40 MO2 Analog monitor 2 offset P S T PC03 STC S-pattern acceleration/ decelerat ...

  • Mitsumi electronic MR-J3- A - page 630

    App. - 3 A PPENDI X App. 1.2 Converter unit No. Symbol Name PA01 *REG Regenerative selection PA02 *MCC Magnetic contactor drive output selection PA03 to PA07 For manufacturer setting PA08 *DMD Auto tuning mode PA09 *BPS Alarm history clear PA10 For manufacturer setting PA11 PA12 *DIF Input filter setting PA13 to PA19 For manufacture setting App. 2 ...

  • Mitsumi electronic MR-J3- A - page 631

    App. - 4 A PPENDI X App. 3 Status display block diagram PWM M Current control Speed control Servo mot or speed Position control Droop pulse Load inertia momen t ratio Auto tuning secti on Cumulative feed back pul se CMX CDV Differ- entia l Elec tronic gear Bus voltage Command pulse PP, NP Speed feedb ack Absolu te position detection encoder Servo m ...

  • Mitsumi electronic MR-J3- A - page 632

    App. - 5 A PPENDI X App. 4 Change of con nector sets to the RoHS compatible produ cts The following connector sets have changed to RoHS compliant since Sep tember 2006. Only the components of the connector s e t that have changed are listed be low. Model Current product RoHS compatible product MR-J3SCNS MR-ECNM Amplifier connector (3M or equivalent ...

  • Mitsumi electronic MR-J3- A - page 633

    App. - 6 A PPENDI X App. 5 MR-J3-200A-RT servo amplifier Connectors (CNP1, CNP2, and CNP3) and appearance of MR-J3-200A servo amplifier have be en changed from June 2014 production. Mode l name of the servo amplifier before March 200 8 is changed to MR-J3-200A- RT. The difference between new MR-J 3-200A servo amplifier and existing MR-J3-200A-RT se ...

  • Mitsumi electronic MR-J3- A - page 634

    App. - 7 A PPENDI X App. 5.2 Configuration including auxiliary equipme nt (1.8 Configuration including auxiliary equi pment) Line noi se filter (FR-BSF01) (Note 3 ) Power supply Magnetic contactor (MC) No-fuse breaker (NFB) or fuse Regenerative option P C L 21 (Note 2) Power factor improving DC reactor (FR-BEL) P 1 P 2 U V W Servo amplifier CN5 CN3 ...

  • Mitsumi electronic MR-J3- A - page 635

    App. - 8 A PPENDI X App. 5.3 CNP1, CNP2, CNP3 wiring method (3.3.3 CNP1, CNP2, CNP 3 wiring method) (a) Servo amplifier power supply connectors Servo amplifier power supply connectors CNP3 CNP1 CNP2 <Applicab le cable examp le> Cable finis h OD: to 5 mm <Applicable cable example> Cable fini sh OD: to 3.8mm Connector for CNP2 54927-0520 ...

  • Mitsumi electronic MR-J3- A - page 636

    App. - 9 A PPENDI X App. 5.4 OUTLINE DRAWINGS (Chapter 10 OUTLINE DRAWI NGS) [Unit: mm] Approx.14 6 21.4 Approx.68 6 6 45 6 mount ing hole Approx .80 195 168 78 6 156 6 6 90 85 With MR-J3BAT Appr ox. 25. 5 Cooling fan air intake Cooling fa n Cooling fan Exhaust Mass: 2.3 [kg] (5.07 [lb]) U V W CNP3 P C D L 11 L 21 CNP2 L 1 L 2 L 3 N P 1 P 2 CNP1 Te ...

  • Mitsumi electronic MR-J3- A - page 637

    App. - 10 A PPENDI X App. 6 Selection example of servo motor power cable POINT Selection condition of wi re size is as follows. Wire length: 30m or less Depending on the cable selecte d, there may be cases that the cable doe s not fit into the Mitsubishi optional or reco mmended cable clamp. Select a cable cla mp according to the cable diameter. Se ...

  • Mitsumi electronic MR-J3- A - page 638

    App. - 11 A PPENDI X App. 7 Handling of AC servo amplifier batte ries for the United Nations Recommendations on the Transport of Dangerous Goods United Nations Recommendations on th e Transpor t of Dangerous Goods Rev. 15 (hereinafter Recommendations of the United Nations) has been issued. To reflect this, transport regulations for lithium metal ba ...

  • Mitsumi electronic MR-J3- A - page 639

    App. - 12 A PPENDI X (5) Transportation precaution for customers For sea or air transportation, the handling label (Figure) is required for the package of a Mitsubishi cell or battery and the outer package containing several packages of Mitsubishi cells or ba tteries. Documentations like the handling label in the specified design and the Shipper&ap ...

  • Mitsumi electronic MR-J3- A - page 640

    App. - 13 A PPENDI X App. 9 Compliance with the European EC directives App. 9.1 What are EC directives? The EC directives were issued to standar dize the regulations o f the EU countries and ensure smooth distribution of safety-guaranteed products. In the EU count ries, the machinery directive (effec tive in January, 1995), EMC directive (e ffectiv ...

  • Mitsumi electronic MR-J3- A - page 641

    App. - 14 A PPENDI X (2) Structure The control circuit provide safe separation to the main circuit in the servo amplifier. (Note) Converter unit Servo motor Contr ol bo x M Servo amplifier (drive unit) No-fuse breaker Magnetic contactor MC Reinforced insulating type 24VDC power supply NFB Note. Servo amplifiers of 22kW or less do not have a convert ...

  • Mitsumi electronic MR-J3- A - page 642

    App. - 15 A PPENDI X (b) Do not connect two ground cables to the same protec tive earth (PE) termina l. Always connect cables to the terminals one-to-one. PE terminals PE terminals (c) If an earth leakage circuit breaker is used, always earth the protective earth (PE) termi nal of th e servo amplifier to prevent an electric shock. (6) Wiring (a) Th ...

  • Mitsumi electronic MR-J3- A - page 643

    App. - 16 A PPENDI X App. 10 Conformance with UL/C-UL standard This servo amplifier complies with UL 508C and CSA C22.2 No.14 standard. (1) Converter units, servo amplifiers (drive units) and s ervo motors used Use the converter units, servo amplifiers (drive units) and servo motors which standard product. Servo amplifier Servo motor HF-KP HF-MP HF ...

  • Mitsumi electronic MR-J3- A - page 644

    App. - 17 A PPENDI X (2) Installation The MR-J3 series have been approved as the products which have been installed in the elec trical enclosure. The minimum enclosure size is based on 150 of each MR-J3 combination. And also, design the enclosure so tha t the ambien t temperature in the enclosure is 55 (131 ) or less, refer to the spec manual. The ...

  • Mitsumi electronic MR-J3- A - page 645

    App. - 18 A PPENDI X (6) Options, peripheral devices Use the UL/C-UL Standard-compliant products. Use the no-fuse breaker (UL489 Listed MCCB) or a Class T fuse indicated in the table below. Servo amplifier No-fuse breaker (Note) Fuse Current Voltage AC Current Voltage AC MR-J3-10A(1) 20A 30A frame 5A 10A MR-J3-40A 20A1 30A frame 10A 15A MR-J3-60A t ...

  • Mitsumi electronic MR-J3- A - page 646

    App. - 19 A PPENDI X (8) Selection example of wires To comply with the UL/C-UL Standard, use UL-approved copper wires rated a t 60/75 (140/167 ) for wiring. The following table shows the wire sizes [AWG] and the crimping ter minal symbols rated at 60 (140 ). The sizes and the symbols ra ted at 75 (167 ) are shown in the brackets. Servo amplifier Co ...

  • Mitsumi electronic MR-J3- A - page 647

    App. - 20 A PPENDI X Servo amplifier Converter Unit (Note 3) Wires [mm 2 ] B1 B2 BU BV BW OH S1 OHS2 MR-J3-10A(1) to 40A(1) 60A 70A MR-J3-100A 200A MR-J3-350A (Note 1) MR-J3-500A 16(16) (Note 1) MR-J3-700A (Note 2) 14(14) (Note 2) 16(16) (Note 1) MR-J3-11KA (Note 1) MR-J3-15KA (Note 1) MR-J3-22KA 14(14) 16(16) (Note 1) M R-J3- DU30KA MR -J3- CR55K ...

  • Mitsumi electronic MR-J3- A - page 648

    App. - 21 A PPENDI X Table: Recommended crimping terminals Servo amplifier side crimping terminals Symbol (Note 2) Applicable tool Manufacturer Crimping terminal Bod y Head Dice a FVD5.5-4 YNT-1210S (Note 1) b 8-4NS YHT-8S C FVD14-6 YF-1 E-4 YNE-38 DH-122 DH-112 D FVD22-6 DH-123 DH-113 (Note 1) e 38-6 YPT-60-21 TD-124 TD-112 YF-1 E-4 YET-60-1 (Note ...

  • Mitsumi electronic MR-J3- A - page 649

    App. - 22 A PPENDI X (10) Overload protection characteristics An electronic thermal relay is built in the servo ampl ifier to protect the servo motor, servo amplifier and servo motor power line from overloads . The operation c haracteristics of the electronic thermal r elay are shown below. It is recommended to use an unbalanced torque-generated ma ...

  • Mitsumi electronic MR-J3- A - page 650

    App. - 23 A PPENDI X (11) Figure configuration Representative configuration example to conform to th e UL/C-UL standard is shown below. The earth wiring is excluded from the figure configur ation. (a) MR-J3-22KA(4) or less Power supply Fuse or no-fuse breaker L 1 ,L 2 ,L 3 L 11 ,L 21 U, V, W Command device Servo amplifier Encoder cable Control pane ...

  • Mitsumi electronic MR-J3- A - page 651

    REVISIONS *The manual number is given on the bott om left of the back cover. Print Data *Manual Number Revision Oct. 2003 SH(NA)030038-A First edition May 2004 SH(NA)030038-B Safety Inst ructions: 4. (1) HF-SP Series serv o motor is added to the environment conditions. Compliance with EC directives in EU: 2.(1) Servo amplifiers MR-J3- 60A/100A/200A ...

  • Mitsumi electronic MR-J3- A - page 652

    Print Data *Manual Number Revision May 2004 SH(NA)030038-B Section 9.1: AL.47 is add ed. AL.E8 is added. Section 9.2: Description of AL.52 is changed. Section 9.3: Paragraph is added. AL.E8 is added. Section 10: Outline drawing is exam ined. Section 10.1 (4): Added. Section 11.1: c. HF-SP152 to 352 is added. Section 11.2 (1): Servo amplifiers MR-J3 ...

  • Mitsumi electronic MR-J3- A - page 653

    Print Data *Manual Number Revision Apr. 2005 SH(NA)030038 -C Section 3. 3.3: Sentence is ad ded into "POINT". Section 3.5 (1) (a): Servo on and servo off condition is delet ed. Part of columns of emergency stop and functions/applic ations is examined. Section 3.5 (1) (b): Zero speed Example is adde d. Section 3.5 (3): The minimum pulse wi ...

  • Mitsumi electronic MR-J3- A - page 654

    Print Data *Manual Number Revision Apr. 2005 SH(NA)030038-C Section 10.1 (5) (6): Added. Section 11.1: d. HF-SP502 702 is added. Section 11.2 (1): Table is examined. Section 11.3: Dynamic brake time constant is added. Chapter 12: "WARNING" 10 minutes ar e modified to 15 minutes. Section 12.1.1: Combinations of cable and co nnector sets di ...

  • Mitsumi electronic MR-J3- A - page 655

    Print Data *Manual Number Revision Oct. 2006 SH(NA)030038-D Section 3.2.1: SD (Plate) is added to CN1. Section 3.3.3 (2) (b) 1): 2.5mm size ferrule model name (for 2 cabl es) is modified. Section 3.3.3 (3): "POINT" is added. Table for parameter No.PD01 in the functio ns/applications column of the forward rotation stroke end and reverse ro ...

  • Mitsumi electronic MR-J3- A - page 656

    Print Data *Manual Number Revision Oct. 2006 SH(NA)030038-D Section 1 0.1 (7): Added. Section 10.2: Examined. Section 11.1: Table is added. Graph is added. Section 11.3: Graph is added. Section 12.1.1: Motor drawing is added. Connector set is added. Change of connector set model. Section 12.1.2 (1) (a): For CN2 connector: Model name is c hanged. Fo ...

  • Mitsumi electronic MR-J3- A - page 657

    Print Data *Manual Number Revision Nov. 2007 SH(NA)03 0038-F "Fan" is changed to "coolin g fan". Charge lamp off confirmation point is examin ed. Fahrenheit is added to temper ature notation. Section 2.1 (1) (b): "POINT" content is changed. Section 2.3 (2): Description of cable fixing method is e xamined. Section 4.1.2 ...

  • Mitsumi electronic MR-J3- A - page 658

    Print Data *Manual Number Revision Dec. 2007 SH(NA)030038-G Section 3.8.1 (2): Addition of Note. Section 3.8.1 (3) (b) 1): Addition of Note. Section 3.8.3 (2): Addition of Note. Section 3.10.2 (2) (a) 1), 2): Connection diag ram and Note 1 and 2 are changed. Section 3.10.2 (3) (a) 1): Connection diagram and Note 1, 2 and 4 are changed. Section 3.10 ...

  • Mitsumi electronic MR-J3- A - page 659

    Print Data *Manual Number Revision Jun. 2008 SH(NA)030038 -H Section 1.7.1 (3) (4): Inte rchanged the model names (3) a nd (4). Made the function and configuration be sam e between MR-J3-200A and MR-J 3- 200A4 in comment. Added the "Note 4" at (3). Section 1.8 (1) (a), (b): Modified the "FR-BLF" to "FR-BSF01". Section ...

  • Mitsumi electronic MR-J3- A - page 660

    Print Data *Manual Number Revision Jun. 2008 SH(NA)030038 -H Section 13.1 (1): De leted the connection in R S-422/232C converter. Section 13.1 (2) (a): Deleted the connection i n RS-422/232C converter. Section 13.1 (2) (b): Changed the RS-422 out put unit. Added "Note 8". Chapter 14: As a "POINT", added the "Taking the dete ...

  • Mitsumi electronic MR-J3- A - page 661

    Print Data *Manual Number Revision Aug. 2010 SH(NA)030038-J Section 3.1 (1) to (3) Section 3.1 (4), (5), (7) Section 3.1 (6) Section 3.1 (7) Section 3.1 (8) Section 3.3.2 (2) Section 3.5 (1) (b) Section 3.5 (2) Section 3.5 (3) Section3.5 (5) Section 3.6.4 (3) (b) Section 3.6.5 (4) (b) Section 3.7 (3) Section 3.10.1 Section 3.10.2 (2) Section 3.10.2 ...

  • Mitsumi electronic MR-J3- A - page 662

    Print Data *Manual Number Revision Aug. 2010 SH(NA)030038-J Section 5.2.2 Section 5.3.1 Section 5.3.2 Section 5.3.3 Section 5.3.4 Section 5.4.1 Section 5.4.2 Section 6.2 Section 6.3.3 Section 6.4 Section 6.6.2 (1) Section 6.6.2 (2) Section 6.9.1 Section 6.9.3 (1) Section 7.1.1 (1) Section 7.2.2 Section 7.2.4 Section 7.3 Section 7.3 (1) (b) Section ...

  • Mitsumi electronic MR-J3- A - page 663

    Print Data *Manual Number Revision Aug. 2010 SH(NA)030038-J Section 8.4 (2) Section 8.4 (3) Section 8.4 (4) (a) Section 8.4 (4) (b) Section 8.5 Section 8.6.3 Section 8.6.4 Section 8.7 Chapter 9 Section 9.1 Section 9.2 Section 10.1 (3), (5) to (9) Section 11.1 Section 11.2 Section 11.3 Section 11.3.1 (1) Section 11.3.1 (2) (a) Section 11.3.1 (2) (b) ...

  • Mitsumi electronic MR-J3- A - page 664

    Print Data *Manual Number Revision Aug. 2010 SH(NA)030038-J Section 12.3.3 (1) (a) Section 12.3.3 (1) (b) Section 12.3.3 (2) Section 12.4 (2) Section 12.5 (5) Section 12.5 (6) Section 12.6 Section 12.6 (2) Section 12.6 (3) (a) Section 12.7 (2) Section 12.7 (4) (b) Section 12.8 (1) Section 12.8 (2) Section 12.9 Section 12.1 1 Section 12.11 (1) Secti ...

  • Mitsumi electronic MR-J3- A - page 665

    Print Data *Manual Number Revision Aug. 2010 SH(NA)030038-J Section 13.3.6 Section 13.5.3 (4) Section 13.5.12 Chapter 14 Section 14.3 Section 14.3.1 Section 14.3.2 Section 14.4 Section 14.5 Section 14.5.1 Section 14.5.2 Section 14.4 to Section 14.11 Section 14.10.3 (2) Section 15.1.1 Section 15.1.3 (1) Section 15.1.3 (2) (a) (b) Section 15.1.6 (1) ...

  • Mitsumi electronic MR-J3- A - page 666

    Print Data *Manual Number Revision Aug. 2010 SH(NA)030038-J Section 15.9.3 (3) Section 15.9.4 Section 15.9.4 (3) Section 15.9.5 Section 15.9.6 Section 15.9.10 Section 16.2 Section 16.5.6 Section 16.5.6 (1) (2) Section 16.6 (1) App. 1 App. 5.4 App. 6 App. 7 App. 8 App. 9 App. 10 Outline dimension dra wings are changed. "POINT" is partially ...

  • Mitsumi electronic MR-J3- A - page 667

    Country/Region Sales office Tel/Fax USA MITSUBISHI ELECTRIC AUTOMATION, INC. 500 Corporate Woods Parkway, Vernon Hills, IL 60061, U.S.A. Tel Fax : +1-847-478-2100 : +1-847-478-2253 Mexico MITSUBISHI ELECTRIC AUTOMATION, INC. Mexico Branch Mariano Escobedo #69, Col.Zona Industrial, Tlalnepantla Edo, C.P.54030, México Tel Fax : +52-55-9171-7600 : +5 ...

  • Mitsumi electronic MR-J3- A - page 668

    Warranty 1. Warra nty period an d coverage We will repair any failure or defect hereinaf ter referred to as "failure" in our FA e quipment hereinafter re ferred to as the "P roduct" ar isen during warrant y period at no cha rge due to causes for which we ar e responsible thro ugh the distrib utor from which you purchased the Pro ...

  • Mitsumi electronic MR-J3- A - page 669

    SH(NA)030038-L ...

  • Mitsumi electronic MR-J3- A - page 670

    SH (NA) 030038-L (1406) MEE Printed in Japan Specifications are subject to change without notice. This Instruction Manual uses recycled paper. MODEL MODEL CODE J3 Series MR-J3- A Servo Amplifier Instruction Manual L General-Purpose AC Servo MODEL MR-J3- A SERVO AMPLIFIER INSTRUCTION MANUAL General-Purpose Interface J3 Series L 1CW203 MR-J3-A INSTRU ...

Fabricant Mitsumi electronic Catégorie Air Conditioner

Les documents que nous recevons du fabricant de l'appareilMitsumi electronic MR-J3- A peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Mitsumi electronic
- manuels d’utilisations MR-J3- A
- fiches produit Mitsumi electronic
- dépliants
- ou étiquettes-énergie Mitsumi electronic MR-J3- A
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Mitsumi electronic MR-J3- A.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Mitsumi electronic MR-J3- A, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Mitsumi electronic MR-J3- A. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Mitsumi electronic MR-J3- A.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Mitsumi electronic MR-J3- A, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Mitsumi electronic MR-J3- A par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Mitsumi electronic MR-J3- A.

Le manuel d’utilisation complet Mitsumi electronic, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Mitsumi electronic MR-J3- A - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Mitsumi electronic MR-J3- A, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lMitsumi electronic MR-J3- A qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Mitsumi electronic MR-J3- A - qui devraient nous aider dans les premières étapes lors de l'utilisation Mitsumi electronic MR-J3- A
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Mitsumi electronic MR-J3- A
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Mitsumi electronic MR-J3- A dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Mitsumi electronic MR-J3- A?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Mitsumi electronic MR-J3- A, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Mitsumi electronic MR-J3- A il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)