Français dropdown-ico

Manuel d’utilisation TP-Link WBS510

21 pages Non applicable
Télécharger

Aller à la page of 21

Summary
  • TP-Link WBS510 - page 1

    I nstallation Guide Outdoor Wireless Base Station WBS210 / WBS510 C OPY RIGHT & TRADEMARKS is a register ed trademark of TP -LINK TECHNOLOGIES C O., L TD . Other brands and product names are trademarks or register ed trademarks of their respective holders. used to make any derivative such as translation, transformation, or adaptation without pe ...

  • TP-Link WBS510 - page 2

    C ontents Overview . Package Contents . Panel Layout Hardwar e Installation Connect cables Mount Antenna Power On Lightning and ESD Pr otection Specification FA Q 1 1 2 3 4 5 7 8 15 16 9 Config uration with P harOS Log in to the PharOS Configure the Base Station . Point-to-Point (PtP) . Point-to-Multipoint (PtMP) . Hotspot 9 12 14 11 11 ...

  • TP-Link WBS510 - page 3

    Overview TP-LINK's Outdoor Wireless Base Stations of the Phar os series products are designed f or outdoor wireless network solutions, aiming at long-distance transmission and large coverage of wireless network . The WBS210 and WBS510 are ideal for deployment in Point -to-Point (PtP) bridging, P oint-to-MultiPoint (PtMP) and Hotspot environmen ...

  • TP-Link WBS510 - page 4

    The panel of Base Station: Panel Layout RESET Shielded Ethernet Port LAN1 Shielded Ethernet Port LAN0(POE IN) Grounding Terminal 2 AP/AP Router mode: All four LEDs remain solid . Client/Bridge/Repeater/AP Client Router mode: The more lit LEDs indicate the better wireless sig nal strength. On: The port is connected but not ac tive. Flashing: The por ...

  • TP-Link WBS510 - page 5

    Passive PoE Adapter Hardw are Installation 3 The Outdoor Wireless Base Stations require external antenna that corresponds to your network environment; a dish antenna for Point-to-Point (PtP) bridge environment, a sector antenna for Point-to-MultiPoint (PtMP) environment, or a columnar antenna for Hotspot environment. Power LED: The Power LED indica ...

  • TP-Link WBS510 - page 6

    4 Affix the waterproof rubber insert to the underside of the device for waterproofing and replace the cover until it firmly locks into place. Use an adequate Ethernet cable (Lenth up to 60m) to connect the LAN0 (POE IN) port. Shielded CAT5e (or above) cable with an integrated ground wire is recommended. 2 Connect the RF Cables to the Base Station. ...

  • TP-Link WBS510 - page 7

    Attach the protective cap. Push and slide the protective cap down over the Base Station until it firmly locks into place. Align the mounting tabs on the back of the Base Station with the four slots of the mounting bracket. Push and slide the Base Station downward until it locks into place. Connect the RF cables from the Base Station to the correspo ...

  • TP-Link WBS510 - page 8

    6 Loosen and completely remove the end of the metal strap by turning the captive screw counterclockwise with a flathead screwdriver. Position the Base Station and wrap the metal strap around the pole. Feed the end back through the screw-block and turn the screw clockwise to tighten the metal strap using a flathead screwdriver until the Base Station ...

  • TP-Link WBS510 - page 9

    7 Connect the Ethernet cable from the Base Station to the POE port of the PoE adapter. Connect an Ethernet cable from your LAN device (a computer, router or switch) to the LAN port on the PoE adapter. Connect the power cord to the power port on the PoE adapter and plug it into an electrical outlet. Connect the Base Station to a Power over Ethernet ...

  • TP-Link WBS510 - page 10

    Lightning and ESD P rotection Use a shielded CAT5e (or above) cable with an integrated grounding wire for connection. If you have the standard CAT5e cable for the connection, use a separate grounding cable to connect the grounding Terminal (GND) to earth ground. Proper grounding is extremely important for outdoor devices. There are two effective te ...

  • TP-Link WBS510 - page 11

    Open a web browser, type http://192.168.0.254 into the address field and press Enter (Windows) or return (Mac). It is recommended to use the latest version of Google Chrome, Firefox or Safari. C onfiguration with PharOS Log in to the PharOS Before accessing the PharOS Web Interface, you need to assign a static IP address 192.168.0.X (X ranges betwe ...

  • TP-Link WBS510 - page 12

    Enter admin for both User Name and Password , then select your Region from the drop-down list. Read and agree the terms of use, then click Login . Change the default User Name and Password to protect your Base Station. Let’s start configuring the Base Staion. 10 3 4 For subsequent logins, use the new username and password. The Reliable Choice ...

  • TP-Link WBS510 - page 13

    1. Log in to PharOS and go to the Quick Setup page. 2. Operation Mode: Select Access Point and click Next . 3. LAN Settings: Click Next . 4. Wireless AP Settings: a. Create a new SSID (Network name) for your wireless network. b. Select WPA-PSK/WPA2-PSK for the Security method and create a PSK Password to protect your AP. c. Enter the distance betwe ...

  • TP-Link WBS510 - page 14

    Point to MultiPoint (PtMP) Configure the Client 12 AP Client Router LAN:192.168.0.254 WAN:Dynamic IP AP Client Router LAN:192.168.0.254 WAN:Dynamic IP AP Client Router LAN:192.168.0.254 WAN:Dynamic IP 1. Log in to PharOS and go to the Quick Setup page. 2. Operation Mode: Select Client and click Next . 3. LAN Settings: Change the IP Address to 192.1 ...

  • TP-Link WBS510 - page 15

    13 Configure the Access Point Configure the AP Client Router (CPEs) 1. Log in to PharOS and go to the Quick Setup page. 2. Operation Mode: Select Access Point and click Next . 3. LAN Settings: Set the IP Address to the same subnet with the root AP or router that you want to connect to, and click Next. 4 . Wireless AP Settings: a. Create a new SSID ...

  • TP-Link WBS510 - page 16

    14 Hotspot Configure the Access Point Smartphone Laptop Tablet Access Point Hotspot is used to provide Internet access to wireless devices such as smartphones, tablets and laptops. Typically, columnar antennas are used in this environment. 1. Log in to PharOS and go to the Quick Setup page. 2. Operation Mode: Select Access Point and click Next . 3. ...

  • TP-Link WBS510 - page 17

    Specification H ardware features Wireless features Interface Dimensions Models Maximum Transmit Power 2 Operating Frequency 2 802.11 Standards Power Supply ESD Protection 1 Lightning Protection 1 Operating Humidity Operating Temperature Certication LAN0 (POE IN) : 10/100/1000Mbps Ethernet port LAN1: 10/100Mbps Ethernet port GND: Grounding termin ...

  • TP-Link WBS510 - page 18

    FA Q How to restore the Base Station to its factory default settings? With the Base Station powered on, press and hold the RESET button on the Base Station or the Remote Reset button on the passive PoE adapter for about 8 seconds until the Wireless Signal Strength LEDs flash. What is Pharos MAXtream? Pharos MAXtream is a proprietary protocol develo ...

  • TP-Link WBS510 - page 19

    2. Click Start , the PharOS will begin to analyze the power of frequency . Observe the curves for a period of time, and then click stop. Note that the relatively low and continuous part of the average curve indicates less radio noise. Here, we use the figure below as an example. 3. When choosing channel/frequency, you should avoid the spectrum with ...

  • TP-Link WBS510 - page 20

    FC C ST A TEMENT CE M ark W arnin g IC ST A TEMENT Safety Information This equipment has been tested and found to comply with the limits f or a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide r easonable protection against harmful interference when the equipment is operated in a commercial environm ...

  • TP-Link WBS510 - page 21

    NC C Notice & BSMI Notic e 注意！ 安全諮詢及注意事項 依據 低功率電波輻射性電機管理辦法 第十二 條 經型式認證合格之低功率射頻電 機 ，非經許 可 ，公 司 、商號或使用 者 均不得擅自變更頻率、加大功率或變更原設計之特性或功能。 第十四 條 低功率射頻電機? ...

Fabricant TP-Link Catégorie Access Point

Les documents que nous recevons du fabricant de l'appareilTP-Link WBS510 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques TP-Link
- manuels d’utilisations WBS510
- fiches produit TP-Link
- dépliants
- ou étiquettes-énergie TP-Link WBS510
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation TP-Link WBS510.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation TP-Link WBS510, manuels d’entretien, brefs manuels ou manuels de l’utilisateur TP-Link WBS510. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit TP-Link WBS510.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil TP-Link WBS510, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser TP-Link WBS510 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs TP-Link WBS510.

Le manuel d’utilisation complet TP-Link, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel TP-Link WBS510 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières TP-Link WBS510, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lTP-Link WBS510 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil TP-Link WBS510 - qui devraient nous aider dans les premières étapes lors de l'utilisation TP-Link WBS510
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de TP-Link WBS510
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service TP-Link WBS510 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de TP-Link WBS510?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec TP-Link WBS510, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec TP-Link WBS510 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (1)

андрюха

где можна найти конкретную инструкцию по подключению? Как клиент.