Manuel d’utilisation KTI Networks KS-220F/S-5

15 pages 0.15 mb
Télécharger

Aller à la page of 15

Summary
  • KTI Networks KS-220F/S-5 - page 1

    -12- Installation Guide 10/100 Bridging Converter KS-220F series DOC.991115-KS220F-K P/N: 750-0126-001 Model: KS-220F/T KS-220F/C KS-220F/S KS-220F/S-A KS-220F/S-3 KS-220F/S-5 ...

  • KTI Networks KS-220F/S-5 - page 2

    -15-  1999 KTI Networks Inc. All rights reserved. No part of this documentation may be reproduced in any form or by any means or used to make any directive work (such as translation or transforma- tion) without permission from KTI Networks Inc. KTI Networks Inc. reserves the right to revise this documentation and to make changes in content from ...

  • KTI Networks KS-220F/S-5 - page 3

    -13- The information contained in this document is subject to change without prior notice. Copyright  KTI. All Rights Reserved. TRADEMARKS Ethernet is a registered trademark of Xerox Corp. WARNING: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits a ...

  • KTI Networks KS-220F/S-5 - page 4

    -14- T able of Contents Chapter 1 Introduction Introduction ............................................................................... 1 Features ................................................................................... 2 Specifications .......................................................................... 3 Chapter 2 Installatio ...

  • KTI Networks KS-220F/S-5 - page 5

    -1- 1. Introduction The 10/100 bridging converter provides two 10/100Mbps-based Fast Ethernet switch ports. Port 1 features one 10/100M UTP connection and Port 2 features either one 10/100M UTP connection or one 100M fiber connection. It provides a cost-effective solution for bridging between 10 and 100Mbps networks, extending distance for 100Mbps ...

  • KTI Networks KS-220F/S-5 - page 6

    -2- Features  Complies with IEEE 802.3u 100BASE-TX 100BASE-FX and IEEE 802.3 10BASE-T specifications  2 switched ports: Port 1 - 10/100M TP port Port 2 - configurable 10/100M TP port or 100M Fiber port  The TP ports support: - auto speed sensing for 100Mbps or 10Mbps connection - auto-negotiation with NW ay devices  Each TP port provide ...

  • KTI Networks KS-220F/S-5 - page 7

    -3- Specifications Standard: 10BASE-T , 100BASE-TX, and 100BASE-FX Connectors: Port 1 - 2 RJ-45 jacks Port 2 - 2 RJ-45 jacks and 1 fiber connector Cables: 10BASE-T - Cat. 3, 4, or 5 UTP cable 100BASE-TX - Cat 5 UTP cable 100BASE-FX - 62.5/125 µ m MM fiber 100BASE-FX - 9/125 µ m SM fiber LED indicators: Link/Activity LED per port, Duplex/Collision ...

  • KTI Networks KS-220F/S-5 - page 8

    -4- 2. Installation Unpacking Check to see that you have everything before you start the installation.  Installation guide  The unit  One AC power adapter for the switch Installation The switch can be placed on a desktop as a stand-alone unit. It also can be mounted on a magnetic-sensitive metal surface with its rub- ber magnet stand locat ...

  • KTI Networks KS-220F/S-5 - page 9

    -5- Checking AC Power One AC power adapter is contained in the product package. Before you begin the installation, check the AC voltage of your area. The AC power adapter which is used to supply the DC power for the unit should have the AC voltage matching the commercial power voltage in your area. The specifications of the AC power adapter are: ? ...

  • KTI Networks KS-220F/S-5 - page 10

    -6- 3. Making Network Connections T wo Switched Ports T wo switched ports are located on the front panel. Configuration Switches On rear panel, Port 1 and Port 2 have individual configuration switches as shown below: Port 1, Port 2 SW1 O f f Auto-negotiation is enabled. On Auto-negotiation is disabled. Port 1, Port 2 SW2 O f f 100Mbps is used. (Whe ...

  • KTI Networks KS-220F/S-5 - page 11

    -7- Important Note: If any change are made to the configuration switch settings, the power to the unit must be turned off and turned on again before the changes can take effect. The auto-negotiation mode enables the port to negotiate a common operation mode with the device connected at the remote end of the link cable. The common operation mode inc ...

  • KTI Networks KS-220F/S-5 - page 12

    -8- UTP Connections The following figure shows a UTP connection from TP port to another device via a straight-through UTP cable. When TP port of Port 2 is used, make sure Port 2 SW4 is set to OFF position. Depending on the configuration switch setting, the operating modes used for connecting to different devices are shown as follows: Connected Devi ...

  • KTI Networks KS-220F/S-5 - page 13

    -9- Fiber Port and Fiber Connection When connecting to a 100BASE-FX device using fiber cable, make sure Port 2 SW4 is set to ON position and TX-to-RX connection rule is followed. Since the fiber connector does not support auto-negotiation func- tion, it is recommended to set SW1 to ON position for the fiber connection. If SW1 is set to OFF , it ope ...

  • KTI Networks KS-220F/S-5 - page 14

    -10- MUL TIMODE FIBER CABLE Connected device Duplex type Maximum length 100Base-FX NIC card Half-duplex 400 meters 100Base-FX NIC card Full-duplex 2K meters 100Base-FX hub port *1 Half-duplex 185 meters 100Base-FX hub port *2 Half-duplex 1 10 meters 100Base-FX switched port Half-duplex 400 meters 100Base-FX switched port Full-duplex 2K meters *1 : ...

  • KTI Networks KS-220F/S-5 - page 15

    -11- 4. Interpreting LED Indicators The following figure shows the locations of the LED indicators: Power State Indication Interpretation On Normal The power of the unit is on. O f f Problem No power is being supplied to the unit. Link/Act. (Link/Activity) State Indication Interpretation On Normal An active link is established. O f f Normal N o act ...

Fabricant KTI Networks Catégorie Switch

Les documents que nous recevons du fabricant de l'appareilKTI Networks KS-220F/S-5 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques KTI Networks
- manuels d’utilisations KS-220F/S-5
- fiches produit KTI Networks
- dépliants
- ou étiquettes-énergie KTI Networks KS-220F/S-5
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation KTI Networks KS-220F/S-5.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation KTI Networks KS-220F/S-5, manuels d’entretien, brefs manuels ou manuels de l’utilisateur KTI Networks KS-220F/S-5. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit KTI Networks KS-220F/S-5.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil KTI Networks KS-220F/S-5, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser KTI Networks KS-220F/S-5 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs KTI Networks KS-220F/S-5.

Le manuel d’utilisation complet KTI Networks, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel KTI Networks KS-220F/S-5 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières KTI Networks KS-220F/S-5, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lKTI Networks KS-220F/S-5 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil KTI Networks KS-220F/S-5 - qui devraient nous aider dans les premières étapes lors de l'utilisation KTI Networks KS-220F/S-5
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de KTI Networks KS-220F/S-5
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service KTI Networks KS-220F/S-5 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de KTI Networks KS-220F/S-5?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec KTI Networks KS-220F/S-5, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec KTI Networks KS-220F/S-5 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Commentaires (0)