Français dropdown-ico

Manuel d’utilisation Poulan 438361

44 pages 3.22 mb
Télécharger

Aller à la page of 44

Summary
  • Poulan 438361 - page 1

    OWNER'S MANUAL MODEL NUMBER: PR8P27ES SNOW THROWER Always W ear Eye Protection During Operation IMPORT ANT MANU AL Do Not Throw Away WARNING: Read the Owner's Manual and fol low all W arnings and Safety In struc tions. F ail ure to do so can result in serious injury . 438361 09.03.10 TH Printed in the U.S.A. ...

  • Poulan 438361 - page 2

    2 IMPORT ANT Safe Operation Practices for W alk-Behind Snow Throwers This snow thrower is capable of amputating hands and feet and throwing objects. F ailure to observe the following safety instructions could result in serious injury . WARNING: This snow thrower is for use on sidewalks, driveways and other ground level surfaces. Caution should be e ...

  • Poulan 438361 - page 3

    3 6. When cleaning, repairing or inspecting the snow thrower , stop the engine and make certain the collector/impel- ler and all moving parts have stopped. Disconnect the spark plug wire and keep the wire away from the plug to prevent someone from accidentally starting the engine. 7. Do not run the engine indoors, except when starting the engine an ...

  • Poulan 438361 - page 4

    4 (1) POWER CORD (198563) (1) DISCHARGE CHUTE (1) LOCKNUT 5/16-18 (751153) (1) CARRIAGE BOL T 5/16-18 x 5/8 (72250505) (1) LOCKNUT 1/4-20 (191730) (1) SHOULDER BOL T 1/4-20 (179829) (1) SPRING (184505) CHUTE DEFLECTOR REMOTE CONTROL (1) AUGER CONTROL ROD SAFTEY IGNITION KEY(S) (193071) (1) MUL TI- WRENCH (180684) (2) FL A T WASHERS (2) CARRIAGE BOL ...

  • Poulan 438361 - page 5

    5 AS SEMBL Y / PRE-OPERA TION SPEED CON TROL ROD SPEED CONTROL BRACKET RET AINER SPRING SPEED CONTROL LEVER FIG. 2 TRACTION DRIVE CON TROL ROD DRIVE CONTROL BRACKET RET AINER SPRING TRACTION DRIVE CON TROL LEVER FIG. 4 SPEED CONTROL ROD HANDLE KNOB L OWER HANDLE PL ASTIC TIE UPPER HANDLE FIG. 1 NOTE: The multi-wrench may be used for assembly of the ...

  • Poulan 438361 - page 6

    6 AS SEMBL Y / PRE-OPERA TION INST ALL DISCHARGE CHUTE / CHUTE ROT A TER HEAD (See Fig. 7) NOTE: The multi-wrench provided in your parts bag may be used to install the chute rotater head. 1. Place discharge chute assembly on top of chute base with discharge opening toward front of snow thrower . 2. Position chute rotater head over chute bracket. If ...

  • Poulan 438361 - page 7

    7 CHECK TIRE PRESSURE The tires on your snow thrower were overinflated at the fac- tory for shipping purposes. Correct and equal tire pres sure is important for best snow throwing performance. • Reduce tire pressure to 14-17 PSI. AS SEMBL Y / PRE-OPERA TION CHUTE DEFLECTOR CONTROL LEVER FIG. 9 FIG. 8 INST ALL CHUTE DEFLECTOR REMOTE CONTROL (See F ...

  • Poulan 438361 - page 8

    8 OPERA TION KNOW YOUR SNOW THROWER READ THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERA TING YOUR SNOW THROWER. Compare the illustrations with your snow thrower to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. These symbols may appear on your snow thrower or in literat ...

  • Poulan 438361 - page 9

    9 MUF FLER GAS O LINE FILLER CAP SAFETY IGNITION KEY CHOKE CON- TROL PRIM ER RECOIL (AUXILIARY) ST ARTER HANDLE ELECTRIC ST ART BUTTON ON / OFF SWITCH OPERA TION ON / OFF switch - used to STOP the engine. Drive speed control lever - used to select forward or reverse motion and speed of snow thrower . T raction drive control lever - used to engage p ...

  • Poulan 438361 - page 10

    10 The operation of any snow thrower can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your snow thrower or performing any ad just- ments or repairs. We recommend standard safe ty glasses or a wide vision safety mask worn over spectacles. HOW TO USE Y ...

  • Poulan 438361 - page 11

    11 TO MOVE FORWARD AND BACK WARD (See Fig. 15) SELF-PROPELLING, forward and reverse movement of the snow thrower , is controlled by the traction drive control lever located on the left side handle. • Squeeze traction drive control lever to handle to en gage the drive system. • Release traction drive control lever to stop the forward or reverse ...

  • Poulan 438361 - page 12

    12 TO ADJUST SKID PL A TES (See Fig. 17) NOTE: The wrench provided in your parts bag may be used to adjust the skid plates. Skid plates are located on each side of the auger housing and adjust the clearance between the scraper bar and the ground surface. Adjust skid plates evenly to proper height for current surface conditions. For removal of snow ...

  • Poulan 438361 - page 13

    13 OPERA TION SNOW THROWING TIPS • Go slower in deep, freezing or heavy wet snow . Use the drive speed control, NOT the ON / OFF switch, to adjust speed. • It is easier and more efficient to remove snow im me- di ate ly after it falls. • The best time to remove snow is the early morning. At this time the snow is usually dry and has not been e ...

  • Poulan 438361 - page 14

    14 MAINTENANCE LUBRICA TION CHART GENERAL REC OM MEN DA TIONS The warranty on this snow thrower does not cover items that have been sub ject ed to operator abuse or negligence. T o receive full value from the warranty , operator must maintain snow thrower as in struct ed in this manual. Some ad just ments will need to be made periodically to proper ...

  • Poulan 438361 - page 15

    15 MAINTENANCE BEL TS Check belts for deterioration and wear after every 50 hours of operation and replace if necessary . The belts are not ad just able. Replace belts if they begin to slip from wear . (See “TO REMOVE BEL T COVER” in the Service and Adjustments section of this manual). The belts on your snow thrower are of special con struc tio ...

  • Poulan 438361 - page 16

    16 SERVICE AND ADJUSTMENTS TO REMOVE BEL T COVER (See Fig. 20) 1. Remove the two (2) screws securing belt cover to frame. 2. Remove belt cover . 3. Replace belt cover by installing cover and screws and tighten securely . FRAME BEL T COVER SCREWS FIG. 20 WARNING: T o avoid serious injury , before performing any service or ad just ments: 1. Be sure t ...

  • Poulan 438361 - page 17

    17 SERVICE AND ADJUSTMENTS 8. RELIEVE TENSION ON TRACTION DRIVE BEL T IDLER and remove traction drive belt from around pulleys. HINT : Insert a 3/8" drive ratchet (in the “ON” position) into the square hole in idler arm and rotate ratchet clockwise to relieve tension. 9. With tension relieved on idler , install new traction drive belt arou ...

  • Poulan 438361 - page 18

    18 ENGINE See engine manual. CARBURETOR Y our carburetor is not adjustable. Engine performance should not be affected at altitudes up to 7,000 feet (2,134 meters). If your engine does not operate properly due to suspected carburetor problems, take your snow thrower to a qualified service center . SERVICE AND ADJUSTMENTS TO ADJUST CABLE TENSION (See ...

  • Poulan 438361 - page 19

    19 STORAGE Immediately prepare your snow thrower for storage at the end of the season or if the unit will not be used for 30 days or more. WARNING: Never store the snow thrower with gaso line in the tank in side a build ing where fumes may reach an open flame, spark or pilot light as on a fur nace, water heater , clothes dryer or gas ap pli ance. A ...

  • Poulan 438361 - page 20

    20 TROUBLESHOOTING Does not start 1. Fuel shut-off valve (if so 1. T urn fuel shut-off valve to OPEN position. equipped) in OFF position. 2. Safety ignition key 2. Insert safety ignition key . is not inserted. 3. Out of fuel. 3. Fill fuel tank with fresh, clean gasoline. 4. Throttle in STOP position 4. Move throttle to FAST position (or ON/OFF swit ...

  • Poulan 438361 - page 21

    21 SERVICE NOTES ...

  • Poulan 438361 - page 22

    22 10 11 11 11 11 1 2 3 4 5 6 7 9 9 9 8 12 12 13 14 15 16 17 18 19 20 21 21 22 22 23 23 24 25 26 27 28 29 30 31 31 32 33 34 35 36 37 37 01.07.026-D 2 (EXPL ODED) REP AIR P ARTS SNOW THROWER - - MODEL NUMBER PR8P27ES (96192004600) AUGER HOUSING / IMPELLER ASSEMBL Y NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Us ...

  • Poulan 438361 - page 23

    23 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . KEY P ART NO . NO . DESCRIPTION REP AIR P ARTS SNOW THROWER - - MODEL NUMBER PR8P27ES (96192004600) AUGER H ...

  • Poulan 438361 - page 24

    24 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . KEY P ART NO . NO . DESCRIPTION REP AIR P ARTS SNOW THROWER - - MODEL NUMBER PR8P27ES (96192004600) AUGER H ...

  • Poulan 438361 - page 25

    25 KEY P ART NO . NO . DESCRIPTION 1 2 3 3 4 01.11.001-B 4 KEY P ART NO . NO . DESCRIPTION NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . 1 174762X431 SKID P ...

  • Poulan 438361 - page 26

    26 KEY P ART NO . NO . DESCRIPTION NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . REP AIR P ARTS SNOW THROWER - - MODEL NUMBER PR8P27ES (96192004600) CONTROL ...

  • Poulan 438361 - page 27

    27 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . KEY P ART NO . NO . DESCRIPTION KEY P ART NO . NO . DESCRIPTION REP AIR P ARTS SNOW THROWER - - MODEL NUMBE ...

  • Poulan 438361 - page 28

    28 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . KEY P ART NO . NO . DESCRIPTION KEY P ART NO . NO . DESCRIPTION REP AIR P ARTS SNOW THROWER - - MODEL NUMBE ...

  • Poulan 438361 - page 29

    29 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . KEY P ART NO . NO . DESCRIPTION 10 11 1 2 3 4 5 6 7 7 9 9 8 8 12 12 13 13 14 14 01.08.002-G 1 412683X431 CO ...

  • Poulan 438361 - page 30

    30 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . KEY P ART NO . NO . DESCRIPTION REP AIR P ARTS SNOW THROWER - - MODEL NUMBER PR8P27ES (96192004600) HANDLES ...

  • Poulan 438361 - page 31

    31 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . KEY P ART NO . NO . DESCRIPTION KEY P ART NO . NO . DESCRIPTION REP AIR P ARTS SNOW THROWER - - MODEL NUMBE ...

  • Poulan 438361 - page 32

    32 9 9 11 11 11 1 2 3 21 5 6 12 13 14 15 20 15 16 17 10 9 8 7 23 19 53 53 53 53 25 26 26 27 39 40 41 42 43 44 32 38 53 53 37 36 35 39 33 28 30 29 31 4 23 24 24 01.02.013-A 18 42 EXPL ODED 24 23 24 33 34 22 47 49 50 48 52 51 46 45 4 REP AIR P ARTS SNOW THROWER - - MODEL NUMBER PR8P27ES (96192004600) DRIVE NOTE: All component dimensions given in U.S. ...

  • Poulan 438361 - page 33

    33 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . KEY P ART NO . NO . DESCRIPTION KEY P ART NO . NO . DESCRIPTION 1 198875 SPEED SELECTOR ASSEMBL Y 2 1750101 ...

  • Poulan 438361 - page 34

    34 KEY P ART NO . NO . DESCRIPTION NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . REP AIR P ARTS SNOW THROWER - - MODEL NUMBER PR8P27ES (96192004600) DRIVE 1 ...

  • Poulan 438361 - page 35

    35 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . REP AIR P ARTS SNOW THROWER - - MODEL NUMBER PR8P27ES (96192004600) CHAS SIS / ENGINE / PULLEYS 1 2 2 3 3 0 ...

  • Poulan 438361 - page 36

    36 KEY P ART NO . NO . DESCRIPTION KEY P ART NO . NO . DESCRIPTION NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . REP AIR P ARTS SNOW THROWER - - MODEL NUMBE ...

  • Poulan 438361 - page 37

    37 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . KEY P ART NO . NO . DESCRIPTION REP AIR P ARTS SNOW THROWER - - MODEL NUMBER PR8P27ES (96192004600) CHAS SI ...

  • Poulan 438361 - page 38

    38 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . REP AIR P ARTS SNOW THROWER - - MODEL NUMBER PR8P27ES (96192004600) WHEELS KEY P ART NO . NO . DESCRIPTION ...

  • Poulan 438361 - page 39

    39 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . REP AIR P ARTS SNOW THROWER - - MODEL NUMBER PR8P27ES (96192004600) WHEELS KEY P ART NO . NO . DESCRIPTION ...

  • Poulan 438361 - page 40

    40 KEY P ART NO . NO . DESCRIPTION KEY P ART NO . NO . DESCRIPTION 1 01.14.007-A 1 193071 SAFETY IGNITION KEY REP AIR P ARTS SNOW THROWER - - MODEL NUMBER PR8P27ES (96192004600) BAG OF P ARTS NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailu ...

  • Poulan 438361 - page 41

    41 KEY P ART NO . NO . DESCRIPTION NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . REP AIR P ARTS SNOW THROWER - - MODEL NUMBER PR8P27ES (96192004600) DECALS ...

  • Poulan 438361 - page 42

    42 SERVICE NOTES ...

  • Poulan 438361 - page 43

    43 SERVICE NOTES ...

  • Poulan 438361 - page 44

    LIMITED W ARRANTY The Manufacturer warrants to the original consumer purchaser that this product as manufactured is free from defects in materials and work man ship. For a period of two (2) years from date of purchase by the original consumer pur - chaser , we will repair or replace, at our option, without charge for parts or labor incurred in repl ...

Fabricant Poulan Catégorie Snow Blower

Les documents que nous recevons du fabricant de l'appareilPoulan 438361 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Poulan
- manuels d’utilisations 438361
- fiches produit Poulan
- dépliants
- ou étiquettes-énergie Poulan 438361
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Poulan 438361.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Poulan 438361, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Poulan 438361. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Poulan 438361.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Poulan 438361, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Poulan 438361 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Poulan 438361.

Le manuel d’utilisation complet Poulan, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Poulan 438361 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Poulan 438361, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lPoulan 438361 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Poulan 438361 - qui devraient nous aider dans les premières étapes lors de l'utilisation Poulan 438361
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Poulan 438361
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Poulan 438361 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Poulan 438361?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Poulan 438361, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Poulan 438361 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)