Français dropdown-ico

Manuel d’utilisation Linear VS-GSWG

34 pages 3.02 mb
Télécharger

Aller à la page of 34

Summary
  • Linear VS-GSWG - page 1

    VS-GSWG Swing Gate Oper ator Installation Guide USA & Canada (800) 421-1587 & (800) 392-0123 (760) 438-7000 - T oll Free FAX (800) 468-1340 www .linearcorp.com Operator models contained in this manual conform to UL325 standard f or use in Class I, II, III, and IV applications ...

  • Linear VS-GSWG - page 2

    VS-GSWG Swing Gate Operator Installation Guide - ii - P1250 Revision X6 7-8-2011 T able of Contents Pre-installation Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Before Y ou Begin... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Alwa ys Check the Gate’ s Action . . . . . . . . . ...

  • Linear VS-GSWG - page 3

    VS-GSWG Swing Gate Operator Installation Guide - 1 - P1250 Revision X6 7-8-2011 Pre-installation Information Before Y ou Begin... Bef ore unpacking, inspect the car ton f or exterior damage. If you fi nd damage, advise the deliv er y carrier of a potential claim. Inspect your pac kage carefully . Y ou can check your accessor y bo x par ts with the ...

  • Linear VS-GSWG - page 4

    VS-GSWG Swing Gate Operator Installation Guide - 2 - P1250 Revision X6 7-8-2011 Wiring Specifi cations Ref er to the follo wing steps for details on po wer and accessor y wiring for the operator . AC P ower Wiring 1. Find the listing on this page corresponding to the model, voltage and horsepower r ating of your operator . 2. The distance shown in ...

  • Linear VS-GSWG - page 5

    VS-GSWG Swing Gate Operator Installation Guide - 3 - P1250 Revision X6 7-8-2011 Mounting P ad Installation The gate operator mounts bolted to posts secured in concrete f ootings. The posts suppor t the operator and pre vent it from mo ving dur ing operation. Gate Prepar ation Bef ore installing the gate operator , make sure the gate’ s s wing is ...

  • Linear VS-GSWG - page 6

    VS-GSWG Swing Gate Operator Installation Guide - 4 - P1250 Revision X6 7-8-2011 Operator Prepar ation Vent Plug Installation In order to keep gear oil from spilling out during shipping, gear reducers used in gate operators ha ve either a solid plug, or a sealed v ent plug, installed at the factory . F or operators with a solid plug, replace the sol ...

  • Linear VS-GSWG - page 7

    VS-GSWG Swing Gate Operator Installation Guide - 5 - P1250 Revision X6 7-8-2011 Operator Setup Controller Access The Controller is protected by a plastic dust co ver . T o remov e the dust cov er , loosen the cov er’ s wing-screw and lift the cov er off (see Figure 5). AC P ower Connection All Linear gate operators are supplied with a po wer disc ...

  • Linear VS-GSWG - page 8

    VS-GSWG Swing Gate Operator Installation Guide - 6 - P1250 Revision X6 7-8-2011 Operator Setup (cont.) Open and Close Limit Adjustment The limit nuts are not preset at the f actor y and must be adjusted f or the gate in each installation. The limit switches are activ ated by tw o threaded nylon rotar y limit nuts which are attached to a threaded li ...

  • Linear VS-GSWG - page 9

    VS-GSWG Swing Gate Operator Installation Guide - 7 - P1250 Revision X6 7-8-2011 T orque Limiter Adjustment Bef ore adjusting the torque limiter , make sure the gate is in good working condition. With the gate disconnected from the gate ar m, one person should be able to mo ve the gate by hand. Be cer tain the gate mov es freely and without binding ...

  • Linear VS-GSWG - page 10

    VS-GSWG Swing Gate Operator Installation Guide - 8 - P1250 Revision X6 7-8-2011 Controller Features S HADOW/ R E S ET P R O GR AMMIN G B UTTON S POWE R INDICATO RS DI S PLAY WHIP ANTENNA OPE R ATION B UTTON S OPE R ATION AND P R O GR AMMIN G INDICATO RS ANTENNA CONNECTO R MOTO R B OA R D COVE R INPUT POWE R TE R MINAL S ACCE SS O R Y POWE R TE R MI ...

  • Linear VS-GSWG - page 11

    VS-GSWG Swing Gate Operator Installation Guide - 9 - P1250 Revision X6 7-8-2011 Indicator Descriptions INDICA TOR DEFINITION INDICA TION WHEN LIT DURING NORMAL OPERA TION INDICA TION WHEN LIT DURING PROGRAMMING OPERA TION PROGRAMMING 24 V OL T INPUT POWER LO W VOL T AGE AC PO WER IS PRESENT 24 V OL T DC ACCY PO WER LOW VOL T AGE DC POWER IS PRESENT ...

  • Linear VS-GSWG - page 12

    VS-GSWG Swing Gate Operator Installation Guide - 10 - P1250 Revision X6 7-8-2011 T erminal Descriptions TERMINAL GROUP FUNCTION AC N 24 V OL T INPUT F ACT OR Y CONNECTED T O 24 V AC FR OM TRANSFORMER OR 24 VDC FROM CONTINUOUS DUTY DC SUPPL Y . AC DC - ACCESSOR Y POWER PRO VIDES 24 V OL T DC POWER FOR ACCESSORIES . (.5A MAX) DC + RESET RESET BUTT ON ...

  • Linear VS-GSWG - page 13

    VS-GSWG Swing Gate Operator Installation Guide - 11 - P1250 Revision X6 7-8-2011 Operator Accessory Connections 3-BUTTON STATION KEYSWITCH FIRE ACCESS SWITCH SINGLE-CHANNEL RADIO RECEIVER WIRELESS GATE EDGE SENSOR M G T T R AN S MITTE R PHOTOEYE FOR REVERSE PHOTOEYE FOR OPEN OBSTRUCTION TELEPHONE ENTRY KEYPAD EXTE R NAL POWE R SOLENOID LOCK MAGLOCK ...

  • Linear VS-GSWG - page 14

    VS-GSWG Swing Gate Operator Installation Guide - 12 - P1250 Revision X6 7-8-2011 Basic Controller Programming Progr amming Overview The Controller can be programmed with v arious options for the operator . The programming fi elds are defi ned as “functions” that ha ve “options”. T o make setup easier f or the installer , the Controller’ ...

  • Linear VS-GSWG - page 15

    VS-GSWG Swing Gate Operator Installation Guide - 13 - P1250 Revision X6 7-8-2011 Basic Controller Programming (Cont.) Run Alarm and Pre-start Alarm The factory default is Run Alarm on and a 3-second Pre-star t Alar m. The operator’ s beeper will sound 3 seconds before the operator star ts. The options are: • Run Alarm Off and Pre-start Alarm Of ...

  • Linear VS-GSWG - page 16

    VS-GSWG Swing Gate Operator Installation Guide - 14 - P1250 Revision X6 7-8-2011 Advanced Controller Progr amming Entering Advanced Progr amming Mode T o access and program the Adv anced Programming functions, f or each programming session, Adv anced Programming must be enab led. After exiting pr ogramming, the Ad vanced Programming functions will ...

  • Linear VS-GSWG - page 17

    VS-GSWG Swing Gate Operator Installation Guide - 15 - P1250 Revision X6 7-8-2011 Advanced Controller Progr amming (Cont.) Auxiliary Relay Mode The Auxiliary Relay has normally open and normally closed contacts. The factory setting disables the A uxiliar y Relay . The relay can be set f or: • Maglock: T o deactivate a magnetic or solenoid gate loc ...

  • Linear VS-GSWG - page 18

    VS-GSWG Swing Gate Operator Installation Guide - 16 - P1250 Revision X6 7-8-2011 Advanced Controller Progr amming (Cont.) Reset Cycle Count The Controller counts of the number of times the operator has been cycled full open and close. The cycle count can be displayed. The display will scroll the cycle count number , fl ashing two digits at a time ...

  • Linear VS-GSWG - page 19

    VS-GSWG Swing Gate Operator Installation Guide - 17 - P1250 Revision X6 7-8-2011 Advanced Controller Progr amming (Cont.) Radio T ransmitter Learn The Controller’ s built-in MegaCode® radio receiv er can store the IDs of up to 40 transmitters. Refer to the fi gure for the steps required to learn transmitters. ✓ NO TE: This function will NO T ...

  • Linear VS-GSWG - page 20

    VS-GSWG Swing Gate Operator Installation Guide - 18 - P1250 Revision X6 7-8-2011 Loop Lay out Illustration ...

  • Linear VS-GSWG - page 21

    VS-GSWG Swing Gate Operator Installation Guide - 19 - P1250 Revision X6 7-8-2011 Safety Edge Lay out Illustration W ARNING One or more contact sensors shall be located on the inside and outside leading edge of a swing gate. Additionally , if the bottom edge of a swing gate is greater than six inches (152 mm) above the ground at any point in its arc ...

  • Linear VS-GSWG - page 22

    VS-GSWG Swing Gate Operator Installation Guide - 20 - P1250 Revision X6 7-8-2011 Photoey e Installation Illustration ...

  • Linear VS-GSWG - page 23

    VS-GSWG Swing Gate Operator Installation Guide - 21 - P1250 Revision X6 7-8-2011 Dual Gate Installations T wo operators can be used in dual gate installations. The operators communicate with each other through the 3-wire COMM LINK terminals. When one operator activ ates, the COMM LINK connection signals the other operator to activ ate. Each operato ...

  • Linear VS-GSWG - page 24

    VS-GSWG Swing Gate Operator Installation Guide - 22 - P1250 Revision X6 7-8-2011 Gate Operation Open Button Opens the gate. If the Controller is programmed to stop opening the gate at mid-tra vel, a constant press of the OPEN button will o verride the Mid-tra vel Stop and completely open the gate. If the A uto Close Timer is set, it will be suspend ...

  • Linear VS-GSWG - page 25

    VS-GSWG Swing Gate Operator Installation Guide - 23 - P1250 Revision X6 7-8-2011 Error Indications During abnor mal operation, the Controller’ s displa ys and beeper will indicate the error condition that has occurred. Entrapment If an entrapment condition occurs detected b y two repeated open or close obstruction tr iggers, the Controller will l ...

  • Linear VS-GSWG - page 26

    VS-GSWG Swing Gate Operator Installation Guide - 24 - P1250 Revision X6 7-8-2011 T roubleshooting Contacting T echnical Support For technical questions regarding Linear gate oper ators, contact the T echnical Ser vices Depar tment at: 1-800-421-1587 fr om 5:00 AM to 4:30 PM P acifi c time Operator fails to start A. If the operator has been running ...

  • Linear VS-GSWG - page 27

    VS-GSWG Swing Gate Operator Installation Guide - 25 - P1250 Revision X6 7-8-2011 Prev entative Maintenance General Linear gate operators are designed f or many y ears of trouble-free oper ation and, under recommended operating conditions, will require only minimal maintenance . T o ensure that a unit is ready f or operation at all times, and to pre ...

  • Linear VS-GSWG - page 28

    VS-GSWG Swing Gate Operator Installation Guide - 26 - P1250 Revision X6 7-8-2011 Model VS-GSWG Exploded View ...

  • Linear VS-GSWG - page 29

    VS-GSWG Swing Gate Operator Installation Guide - 27 - P1250 Revision X6 7-8-2011 MODEL SWG MECHANICAL P ARTS LIST REF . # P ART # DESCRIPTION 2120-361 Complete Enclosure Assembly with Door 1 2110-067 Enclosure Assembly without Door 2120-362 Enclosure Door and Lock Assembly 2110-643 Snap Lock Assembly only 2 2110-161 Mounting Panel Assembly 3 2100-7 ...

  • Linear VS-GSWG - page 30

    VS-GSWG Swing Gate Operator Installation Guide - 28 - P1250 Revision X6 7-8-2011 Controller P arts List S HADOW/ R E S ET OPEN/RESET 6 8 3 1 4 9 5 10 2 VS-GSWG CONTROLLER MECHANICAL P ARTS LIST REF . # P ART # DESCRIPTION V ariable Speed Control Bo x Assemblies 2520-543 1/2 HP , 115V , 1-Phase Controller 2520-544 1/2 HP , 208/230V , 1-Phase Control ...

  • Linear VS-GSWG - page 31

    VS-GSWG Swing Gate Operator Installation Guide - 29 - P1250 Revision X6 7-8-2011 V ariable Speed Drive Progr amming Progr amming the Hitachi Inverter 1. Apply pow er 2. Press FUNC 3. Use ▲▼ arrows to adv ance to F_ _ ( F002 f or L200) 4. Press FUNC arrow to get to F02 (L100 ONL Y) 5. Press FUNC , arrows to change to 3.0 ( 3.00 f or L200), STR 6 ...

  • Linear VS-GSWG - page 32

    VS-GSWG Swing Gate Operator Installation Guide - 30 - P1250 Revision X6 7-8-2011 GA TE ARM ASSEMBL Y MECHANICAL P ARTS LIST REF . # P ART # DESCRIPTION 2110-648 Gate Ar m Assembly , 78” (complete) 1 2110-312 Welded Rail Assembly , 78” 9 2110-248 Upper Rail Guide Assembly , with Bearing 12 2220-011 Sprocket, 40-B-13, 7/8” bore, with Bearing 13 ...

  • Linear VS-GSWG - page 33

    VS-GSWG Swing Gate Operator Installation Guide - 31 - P1250 Revision X6 7-8-2011 This page left blank intentionally . ...

  • Linear VS-GSWG - page 34

    VS-GSWG Swing Gate Operator Installation Guide - 32 - P1250 Revision X6 7-8-2011 Gate Operator Installation Checklist ❑ ❑ 1. The gate has been chec ked to make sure it is le vel and mov es freely in both directions. ❑ ❑ 2. P otential pinch areas hav e been guarded so as to be inaccessible OR ha ve contact and/or non-contact obstruction sens ...

Fabricant Linear Catégorie Safety Gate

Les documents que nous recevons du fabricant de l'appareilLinear VS-GSWG peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Linear
- manuels d’utilisations VS-GSWG
- fiches produit Linear
- dépliants
- ou étiquettes-énergie Linear VS-GSWG
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Linear VS-GSWG.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Linear VS-GSWG, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Linear VS-GSWG. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Linear VS-GSWG.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Linear VS-GSWG, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Linear VS-GSWG par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Linear VS-GSWG.

Le manuel d’utilisation complet Linear, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Linear VS-GSWG - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Linear VS-GSWG, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lLinear VS-GSWG qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Linear VS-GSWG - qui devraient nous aider dans les premières étapes lors de l'utilisation Linear VS-GSWG
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Linear VS-GSWG
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Linear VS-GSWG dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Linear VS-GSWG?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Linear VS-GSWG, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Linear VS-GSWG il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)