Français dropdown-ico

Manuel d’utilisation Siemens 500

35 pages 0.52 mb
Télécharger

Aller à la page of 35

Summary
  • Siemens 500 - page 1

    ANIM-03522-0612 (New Issue) ©2012 Siemens Industr y, Inc. All rights reserved. Installation Operation Maintenance Horizontal – Medallion  500, 580, 880, SH400, SH450, SH560 Frames TEFC Enclosures Type CZ, NCZ, CGZ, 1LA4 Induction Motors/ Generators ...

  • Siemens 500 - page 2

    - 1 - Table of Contents Page Page TABLE OF CONTENTS 1 OPERATION 11 SAFETY PROCEDURES 2 Initial Start 11 INTRODUCTION 3 Oil Circulating Systems 11 Warranty 3 Normal Operation 11 Receiving 3 Voltage/Frequency Variation 11 Handling 4 Trouble Shooting 12 Temporary Storage 4 MAINTENANC E 14 Type Designations 4 Preventive Maintenance 14 INSTALLATION 5 In ...

  • Siemens 500 - page 3

    - 2 - Safety Procedures This equipment contains haza rdous voltages. Death, serious perso nal injury or property damage can resu lt if safety instructions are not followed. The successful and safe ope ration of motors and generators is depend ent upon proper handling, installation, operation and mainte nance, as well as upon proper design and manuf ...

  • Siemens 500 - page 4

    - 3 - Introduction DANGER Hazardous voltage. Will cause death, serious injur y, electrocution or propert y damage. Disconnect all power before working on this equipment. These instructions present general recommendations for installation, operation and m aintenance of induction motors built at the Norwo od plant. If additional information i s requi ...

  • Siemens 500 - page 5

    - 4 - Introduction WARNING Heavy equipment. Improper handling may cause death, seri ous injury or property damage. Check lifting devices before lifting. Use proper slings, chains and spreaders. Note any warning plates on motor and foll ow instructions on each plate. Handling Lifting devices are provided for handling only. An experienced rigger shou ...

  • Siemens 500 - page 6

    - 5 - Installation Motor Dimensions For motors built in the frame si zes covered by this manual, the letter dim ensions have the same definitions as established NEMA standards. Established dimensions for these frames may be found on catalog sheets or ce rtified dra wings. CAUTION Damp Location. Can cause propert y damage if equipment is oper ated i ...

  • Siemens 500 - page 7

    - 6 - Installation External Wiring DANGER Hazardous voltage. Will cause death, serious injur y, electrocution or propert y damage. Disconnect all power before working on this equipment. NOTE Before runnin g motor, see Initial Start. Starting and overload control devi ces must be matched to motor rating. For safety or convenience they may need to be ...

  • Siemens 500 - page 8

    - 7 - Installation Angular Alignment Hold each shaft at maximu m end float. Rotate both shafts together, and measure b etween matching points at the outside diameter of the coupli ng faces for the top, bottom and both sides. Use two indicat ors because of possible axial shaft movement. Read difference of variation between them. Align shafts so that ...

  • Siemens 500 - page 9

    - 8 - Installation Hot Alignment It is possible for the motor shaft height to change relative to the driven equipment and this should be compensated for during the alignme nt procedure. Heat from driven equipme nt can al so cause horizontal misalignment. WARNING Rotating parts. Can cause serious injury. Disconnect and lock out power before working ...

  • Siemens 500 - page 10

    - 9 - Installation Doweling Doweling the moto r (and driven unit) accomplis h es the following: 1. Restrict s movement. 2. Eases realignment if motor is removed from base. 3. Temporarily restrains the motor, shoul d mounting bolts loosen. Inserting Dowel Pins The following procedure is recomme nde d: a. Check the alignment after the unit has been i ...

  • Siemens 500 - page 11

    - 10 - Installation Typical Motor Control Settings Alarm Trip (Shutdown) Timer Trip Setting (1) Winding Temperature  Class B Insulation  Class F Insulation 130°C 155°C 155°C 170°C Motor Bearing Temperature (Thermocouple or RTD’s)  Sleeve Bearing 100°C 105°C  Antifriction Bearing 100°C 105°C Ground Fault 4 Amps (2) Primary Circ ...

  • Siemens 500 - page 12

    - 11 - Operation Initial Start CAUTION Do not exceed nu mb er o f Siemens specified hot and cold starts per hour. Will cause overheating. Allow time between starts to permit stator windings and rotor cage to cool. After installation is completed, but before motor is pu t in regular service, make an initial start as follows: 1. Check that motor, sta ...

  • Siemens 500 - page 13

    - 12 - Operation Trouble Shooting Between regular maintenance inspe ctions, be alert for signs of motor trouble. Comm on symptoms are listed in the following table. Correct any trouble immediately an d AVOID COSTLY REPAIR AND SHUT DOWN. TROUBLE POSSIBLE CAUSES CORRECTION Usually line trouble. Singl e phasing at starter. Check power source. DO NOT c ...

  • Siemens 500 - page 14

    - 13 - Operation Trouble Shooting TROUBLE POSSIBLE CAUSES CORRECTION Open stator windings. Disconnect motor from load. Check idle amps for balance in all three phases. Check stator resistance in all three phases for bala nce. Air Recirculation. Check air intake and exhaust for obstructions. Check air inlet temperature. Over voltage/under voltage. C ...

  • Siemens 500 - page 15

    - 14 - Maintenance Preventive Maintenance Motors are designed to give many years of reliable service with a minimum of attention. Trouble-free operation cannot be expected if p roper maintenance is postponed or negl ecte d. Provide proper maintenance on the equipm ent. Follow carefully the instructions containe d herein. Be certain personnel review ...

  • Siemens 500 - page 16

    - 15 - Maintenance Hazardous Location WARNING Explosion or fire. Can cause death, serious injur y or pr opert y damage. Do not modify or change any motor accessories, which are not suitable for the area classification. Any part replacements are accurate duplicates of the original to maintain the hazardous area classificati on. Consult manufacturer ...

  • Siemens 500 - page 17

    - 16 - Maintenance Temperature Electrical apparatus operatin g under normal conditions becomes quit e warm. Although som e places may feel hot to the tou ch, the unit may be within limits. If checking total temperature by winding resistance or imbedd ed detector (RTD), the total temperature should not exceed the follo wing: When operating at full l ...

  • Siemens 500 - page 18

    - 17 - Maintenance Rotor Cleaning Remove rotor. Inspect and clean. Stator Cleaning Micalastic™ form wound VPI (vacuum pressu re impregnated) insulated coils may be cleane d with solvent using lint free clot hs or steam cleaned with low-pressure steam, then the e ntire stator oven baked at 170 °F for 6 hou rs and then 245°F for 12 hours. The sta ...

  • Siemens 500 - page 19

    - 18 - Maintenance Electric Strip Heater Drying 1. Remove bearing housing s. 2. Remove rotor. 3. Direct a fan on stator to carry away the moisture. 4. Attach temperature i ndicators to winding and apply heat as specified in the Insulation Drying Temperature table and follo w procedures described for drying insulation. 5. Radiant type heaters are no ...

  • Siemens 500 - page 20

    - 19 - Maintenance Insulated Bearings One or both bearings m ay be insulated to prevent shaft currents from pitting bearing surfaces. The insulation is located at the joint between the bearing housing or bracket a nd the bearing. Insulat ed bearings are designated by an instruction plate on the bearing housing. Check periodically to be sure the ins ...

  • Siemens 500 - page 21

    - 20 - Maintenance At the first sign of oil discoloration or contamination, replace with new oil. Rapi d discoloration is caused by bearing wear, often from vibration or thrust. Chang e oil as required to keep cle an. When assembling the bea ring, it is possible to foul the rings so that they will not turn freely. Check ring operation by rotating s ...

  • Siemens 500 - page 22

    - 21 - Maintenance Sealing Parts Even though joints may seem to match perfectly, minute clearances exist through which oil may leak. Sealant should be ap plied to the mating surfaces of parts where oil is present to prevent seepage of oil. Sealant should be applied as follo ws: 1. Surfaces shall be clean of dirt, grease, and oil sealant. Use a non- ...

  • Siemens 500 - page 23

    - 22 - Maintenance Sleeve Bearings CAUTION Maintain proper oil lev el. Failure to do so may cause improper lubric ation of motor resulting in damage to the equipm ent. Follow lubrication instructions carefully. Avoid adding oil while unit is running. Motors with sleeve bearings are shipped without oil. A rust-inhibiting film is applied at the facto ...

  • Siemens 500 - page 24

    - 23 - Maintenance To Replace Antifriction Bearings 1. Remove bolts holding end caps to housi ngs. 2. Remove bolts holding bearing housin gs t o yoke. 3. Remove bearing housing s. 4. Remove the bearing with a puller. See Figure 6. 5. Check shaft and housing diameter for prop er size with micrometer. 6. Heat the new bearing in an oven (200°F). Whil ...

  • Siemens 500 - page 25

    - 24 - Maintenance Protect the shaft end with a cap. If bearing is reusable, make certain the puller applies pressure a ga inst the bearing inner race only. If puller will not hook the bearing inner race, fabricate a split bushing an d install it between the bearing and the puller h ooks. Figure 6. Removing Bearing with a Puller Sleeve Bearing When ...

  • Siemens 500 - page 26

    - 25 - Maintenance 11. Lubricate. Turn moto r by hand to be su re of proper fit and oil ring operation. 12. Start motor without load and check oil ring operation. Figure 8. Sleeve bearing construction with labyrinth-type oil seals-580 Frame. 880, SH400, SH450, and SH56 0 Frames (See Figure 9) 1. Chec k replacement bearings fo r nicks or shipping da ...

  • Siemens 500 - page 27

    - 26 - Spare Parts Identification All units have an identification nam eplate affixed to the frame (Figure 10 & 11). Al l the necessary information pertaining to the motor can be found on this plate including; 1. Serial Number 2. Type and Frame Size 3. Horsepower and Speed 4. Bearing Designations It is important when orderin g spare parts or di ...

  • Siemens 500 - page 28

    - 27 - Spare Parts Figure 11. Identification Plate – Hazardous L ocation Figure 12. Type CZ, 509 / 5011 / 5013 Frames Item Description Item Description Item Description 1 Stator Core 7 Ball Bearing 14 Inboard Seal 2 Stator Yoke 8 Shaft Seal 15 Oil Seal 3 Stator Coils 10 Grid Cover 16 Bearing Capsule 4 Bearing Housing 11 Rotor Core 17 Sleeve Beari ...

  • Siemens 500 - page 29

    - 28 - Spare Parts Item Description Item De scription 1 Stator Core 8 Shaft Seal 2 Stator Yoke 10 Grid Cover 3 Stator Coils 11 Rotor Core 4 Bearing Housing 12 External Fan (4 Pole or Slower) 5 Rotor Shaft 13 Fan Housi ng 6 Inner End Cap 14 Internal Fan 7 Ball Bearing 15 Rotor Air Duct Figure 15. Type CZ, 588 / 5810 / 5812 Frames Item Description 16 ...

  • Siemens 500 - page 30

    - 29 - Spare Parts Figure 16 . Sleeve Bearing Arrangement for Type CGZ 880, SH400, SH450, Type 1LA4 SH560 Frames Item Description 18 Oil Seal 19 Bearing Cap. Housing 20 Sleeve Bearing Bushing 21 Shims 22 Machine Seal 23 Oil Ring Item Description Item De scription 1 Stator Core 8 Shaft seal 2 Stator Yoke 10 Grid Cover 3 Stator Coils 11 Rotor Core 4 ...

  • Siemens 500 - page 31

    - 30 - Spare Parts Item Description Item Description 1 Stator Core 9 Outer End Cap 2 Stator Yoke 10 Grid Cover 3 Stator Coils 11 Rotor Core 4 Bearing Housing 5 Rotor Shaft 12 External Fan (Directional) 6 Inner End Cap 13 Fan Housing 7 Ball Bearing 14 Internal Fan 8 Shaft seal 15 Roller Bearing Figure. 20 . Type 1LA4, SH560 Frame ...

  • Siemens 500 - page 32

    - 31 - Motor Service Record Serial No ______________________ Horsepower ______________ Type ___________ Speed ________ Volts _____________ Amperes _____________ Hertz _______ Insulation Class _______ Temperature Rise _______  C Frame Size ____________ Owner Order No _________________ Item No _____ Date Of Manufacture _________ MACHINE TYPE BEARI ...

  • Siemens 500 - page 33

    - 32 - Vibration Analysis Sheet Pick-Up Filter-Out Coupled Filter-In Couple d Disp. Freq* Vel. Freq.* Vel. Freq . Vel. Freq. Vel. Freq. Vel. Freq. Point Pos ition Mils CPM In/Sec CPM Mils CPM Mils CPM Mils CPM Mils CPM Horizontal Vertical Axi al Horizontal Vertical Axi al Horizontal Vertical Axi al Horizontal Vertical Axi al Horizontal Vertical Axi ...

  • Siemens 500 - page 34

    - 33 - Notes ___________________ ______________ ___________________ __________________ __________________ __ ___________________ ______________ ___________________ __________________ __________________ __ ___________________ ______________ ___________________ __________________ __________________ __ ___________________ ______________ ______________ ...

  • Siemens 500 - page 35

    ANIM-03522-0612 (New Issue) ©2012 Siemens Industr y, Inc. All rights reserved. Siemens Industry Drive Technologies Divisio n Norwood Motor Plant 4620 Forest Avenue Norwood, OH 45212-3396 (513) 841-31 00 ...

Fabricant Siemens Catégorie Portable Generator

Les documents que nous recevons du fabricant de l'appareilSiemens 500 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Siemens
- manuels d’utilisations 500
- fiches produit Siemens
- dépliants
- ou étiquettes-énergie Siemens 500
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Siemens 500.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Siemens 500, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Siemens 500. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Siemens 500.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Siemens 500, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Siemens 500 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Siemens 500.

Le manuel d’utilisation complet Siemens, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Siemens 500 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Siemens 500, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lSiemens 500 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Siemens 500 - qui devraient nous aider dans les premières étapes lors de l'utilisation Siemens 500
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Siemens 500
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Siemens 500 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Siemens 500?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Siemens 500, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Siemens 500 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)