Français dropdown-ico

Manuel d’utilisation Cypress CY7C68053

39 pages 1.21 mb
Télécharger

Aller à la page of 39

Summary
  • Cypress CY7C68053 - page 1

    MoBL-USB™ FX2LP18 USB Microcontroller CY7C68053 Cypress Semiconductor Corpora tion • 198 Champion Cou rt • San Jose , CA 95134-1 709 • 408-943-2 600 Document # 001-06120 Rev *F Revised September 9th 2006 1.0 CY7C68053 Features • USB 2.0 – USB-IF High-S peed and Full-S peed Compliant (TID# 40000188 ) • Single-chip integrated USB 2.0 tr ...

  • Cypress CY7C68053 - page 2

    CY7C68053 Document # 001-06120 Rev *F Page 2 of 39 Cypress Semiconductor Corporation’s MoBL-USB  FX2LP18 (CY7C68053) is a low-voltage (1.8 volt) version of the EZ- USB ® FX2LP (CY7C68013A), which is a hi ghly integrated, low-power USB 2.0 microcontrolle r . By integrating the USB 2.0 transceiver , serial interface engine (SIE), enhanced 8051 ...

  • Cypress CY7C68053 - page 3

    CY7C68053 Document # 001-06120 Rev *F Page 3 of 39 3.3 I 2 C™ Bus FX2LP18 supports the I 2 C bus as a master only at 100-/400- KHz. SCL and SDA pins h ave open-drain outputs and hysteresis inputs. These si gnals must be pulled u p to either V CC or V CC_IO , even if no I 2 C device is connected.(Connecting to V CC_IO may be more convenient.) 3.4 ...

  • Cypress CY7C68053 - page 4

    CY7C68053 Document # 001-06120 Rev *F Page 4 of 39 pushes the program counter onto its stack then jumps to address 0x0043, where it expe cts to find a ‘jump’ instruction to the USB inter rupt service rout ine. The FX2LP18 jump i nstruction is encode d as shown in Ta b l e 3 - 2 . If Autovectoring is enabled (A V2EN = 1 in the INT SET -UP regist ...

  • Cypress CY7C68053 - page 5

    CY7C68053 Document # 001-06120 Rev *F Page 5 of 39 3.9 Rese t and W akeup The reset and wakeup pins are describe d in detail in this section. 3.9.1 Reset Pin The input pin, RESET#, resets the FX2LP18 when asserted. This pin has hysteresis and is active LOW . When a crystal is used with the CY7C68053, the reset pe riod must allow for the stabilizati ...

  • Cypress CY7C68053 - page 6

    CY7C68053 Document # 001-06120 Rev *F Page 6 of 39 3.10 Program/Dat a RAM This sectio n describes the FX2LP1 8 RAM. 3.10.1 Size The FX2LP18 has 16 kBytes of internal program/data RAM. No USB control re gisters appear in this space. Memory maps are shown in Figure 3-3 and Figure 3-4 . 3.10.2 Interna l Code M emory This mode implements the internal 1 ...

  • Cypress CY7C68053 - page 7

    CY7C68053 Document # 001-06120 Rev *F Page 7 of 39 vertical columns of Figure 3-5 . When operating in fu ll-speed BULK mode only the first 64 bytes of e ach buffer are used. For example, in high-speed the maximum packet size is 512 bytes, but in full-speed it is 64 bytes. Even though a buffer is configured to be a 512 byte buffer , in full-speed on ...

  • Cypress CY7C68053 - page 8

    CY7C68053 Document # 001-06120 Rev *F Page 8 of 39 3.12.6 Defaul t High-Speed Alte rnate Settings 3.13 External FIFO In terface The architecture, control si gnals, and clock rates are presented in th is section. 3.13.1 Architecture The FX2LP18 slave FIFO architecture h as eight 512-byte blocks in the endpoint RAM th at directly serve as FIFO memori ...

  • Cypress CY7C68053 - page 9

    CY7C68053 Document # 001-06120 Rev *F Page 9 of 39 3.14.1 Three Control OUT Sign als The 56-pin package brings out three of these si gnals, CTL0–CTL2. The 8051 programs the GPIF unit to defi ne the CTL waveforms. C TLx waveform edges can be pro grammed to make transitions as fast as once per clock cycle (20.8 ns using a 48 MHz clock). 3.14.2 T wo ...

  • Cypress CY7C68053 - page 10

    CY7C68053 Document # 001-06120 Rev *F Page 10 of 39 3.18.2 I 2 C Interface Boot Load Access At power on reset the I 2 C interface boo t loader loads the VID/PID/DID and configuration bytes and up to 16 kBytes of program/data. The available RAM spaces are 16 kBytes from 0x0000–0x3FFF and 512 bytes from 0xE000–0xE1FF . Th e 8051 is reset. I 2 C i ...

  • Cypress CY7C68053 - page 11

    CY7C68053 Document # 001-06120 Rev *F Page 1 1 of 39 Figure 4-2. CY7C68053 56-pin VF BGA Pin Assignment - T op view 12345 678 A B C D E F G H 1A 2A 3A 4A 5A 6A 7A 8A 1B 2B 3B 4B 5B 6B 7B 8B 1C 2C 3C 4C 5C 6C 7C 8C 1D 2D 7D 8D 1E 2E 7E 8E 1F 2F 3F 4F 5F 6F 7F 8F 1G 2G 3G 4G 5G 6G 7G 8G 1H 2H 3H 4H 5H 6H 7H 8H [+] Feedback ...

  • Cypress CY7C68053 - page 12

    CY7C68053 Document # 001-06120 Rev *F Page 12 of 39 4.1 CY7C68053 Pin Description s Note 9. Unused inputs must not be left float ing. T ie either HIGH or LOW as appropriate. Output s should only be pulled up or down to ensure signals at power up and in standby . Note also that no pins should be driven while the devi ce is powered down T able 4-1. F ...

  • Cypress CY7C68053 - page 13

    CY7C68053 Document # 001-06120 Rev *F Page 13 of 39 6F P A4 or FIFOADR0 I/O/Z I (P A4) Multiplexed pin whose function is selected by: IFCONFIG[1:0] . PA 4 is a bidirectional IO port pin. FIFOADR0 is an i nput-only address select for the slave FIFO’s connected to FD[7:0] or FD[15:0]. 8C P A5 or FIFOADR1 I/O/Z I (P A5) Multiplexed pin whose functio ...

  • Cypress CY7C68053 - page 14

    CY7C68053 Document # 001-06120 Rev *F Page 14 of 39 PORT D 8A PD0 or FD[8] I/O/Z I (PD0) Multiplexed pin whose function is selected by the IFCONFIG[1:0] and EPxFIFOCFG .0 (wordwide) bi ts. FD[8] is the bidirection al FIFO/GPIF data bus. 7A PD1 or FD[9] I/O/Z I (PD1) Multiplexed pin whose function is selected by the IFCONFIG[1:0] and EPxFIFOCFG .0 ( ...

  • Cypress CY7C68053 - page 15

    CY7C68053 Document # 001-06120 Rev *F Page 15 of 39 2G IFCLK I/O/Z Z Interface Clock, u sed for syn chronousl y clocking data into or out of the slave FIFO’s. IFCLK also serves as a timing reference for a ll slave FIFO control signals and GPIF . When internal clocking is use d (IFCONFIG . 7 = 1) the IFCLK pin can be configured to out put 30/48 MH ...

  • Cypress CY7C68053 - page 16

    CY7C68053 Document # 001-06120 Rev *F Page 16 of 39 5.0 Register Summary FX2LP18 register bit definit ions are described in the MoBL-USB TRM in greater de tail. T able 5-1. FX2 LP18 Register Summary Hex Size Name Description b7 b6 b5 b4 b3 b2 b1 b0 Default Access GPIF W aveform Me mories E400 128 WA VE DAT A GPIF W aveform Descriptor 0, 1, 2, 3 dat ...

  • Cypress CY7C68053 - page 17

    CY7C68053 Document # 001-06120 Rev *F Page 17 of 39 E62C 1 ECC1B2 ECC1 Byte 2 Address COL5 COL4 COL3 COL2 COL1 COL0 LINE17 LINE16 00000000 R E62D 1 ECC2B0 ECC2 Byte 0 Address LINE15 LINE14 LINE13 LINE12 LINE1 1 LINE10 LINE 9 LINE8 00000000 R E62E 1 ECC2B1 ECC2 Byte 1 Address LINE7 LINE6 LINE5 LINE 4 LINE3 LINE2 LINE1 LINE0 0 0000000 R E62F 1 ECC2B2 ...

  • Cypress CY7C68053 - page 18

    CY7C68053 Document # 001-06120 Rev *F Page 18 of 39 E65E 1 EPIE End point Interrupt Enables EP8 EP6 EP4 EP2 EP1OUT EP1IN EP0OU T EP0IN 00000000 RW E65F 1 EPIRQ [1 1] Endpoint Interrupt Requests EP8 EP6 EP4 EP2 EP1OUT EP1IN EP0OU T EP0IN 0 RW E660 1 GPIFIE [10] GPIF Interrupt Enable 0 0 0 0 0 0 GPIFWF GPIFDONE 00000000 RW E661 1 GPIFIRQ [10] GPIF In ...

  • Cypress CY7C68053 - page 19

    CY7C68053 Document # 001-06120 Rev *F Page 19 of 39 E6A1 1 EP1OUTCS Endpoint 1 OUT Cont rol and S ta tus 0 0 0 0 0 0 BUSY ST ALL 00000000 bbbbbbrb E6A2 1 EP1INCS Endpoin t 1 IN Control an d Sta t u s 0 0 0 0 0 0 BUSY ST ALL 00000000 bbbbbbrb E6A3 1 EP2CS End point 2 C ontrol an d Sta t u s 0 NP AK2 NP AK1 NP AK0 FULL EMPTY 0 ST ALL 0010 1000 rrrrrr ...

  • Cypress CY7C68053 - page 20

    CY7C68053 Document # 001-06120 Rev *F Page 20 of 39 E6CF 1 GPIFTCB2 [10] GPIF T ransaction Count Byte 2 TC23 TC22 TC21 TC20 TC19 TC18 TC17 TC16 00000000 RW E6D0 1 GPIFTCB1 [10] GPIF T ransaction Count Byte 1 TC15 TC14 TC13 TC12 TC1 1 TC10 TC9 TC8 0000 0000 RW E6D1 1 GPIFTCB0 [10] GPIF T ransaction Count Byte 0 TC7 TC6 TC5 TC4 TC3 TC2 TC1 TC0 000000 ...

  • Cypress CY7C68053 - page 21

    CY7C68053 Document # 001-06120 Rev *F Page 21 of 39 81 1 SP S tack Pointer D7 D6 D5 D4 D3 D2 D1 D0 000001 1 1 RW 82 1 DPL0 Data Pointer 0 L A7 A6 A5 A4 A3 A2 A1 A0 00000000 RW 83 1 DPH0 Data Pointer 0 H A15 A14 A13 A1 2 A1 1 A10 A9 A8 00000000 RW 84 1 DPL1 [12] Data Pointer 1 L A7 A6 A5 A4 A3 A2 A1 A0 00000000 RW 85 1 DPH1 [12] Data Pointer 1 H A15 ...

  • Cypress CY7C68053 - page 22

    CY7C68053 Document # 001-06120 Rev *F Page 22 of 39 C9 1 Reserved CA 1 RCAP2L Captur e for T imer 2, auto- reload, up- counter D7 D6 D5 D4 D3 D2 D1 D0 00000000 RW CB 1 RCAP2H Captur e for T imer 2, auto- reload, up- counter D7 D6 D5 D4 D3 D2 D1 D0 00000000 RW CC 1 TL2 T imer 2 reload L D7 D6 D5 D4 D3 D2 D1 D0 00000000 RW CD 1 TH2 T imer 2 reload H ...

  • Cypress CY7C68053 - page 23

    CY7C68053 Document # 001-06120 Rev *F Page 23 of 39 6.0 Absolute Maximum Ratings S torage T emperature . .............. ............ .............. .............. ........... .............. .............. ........... ... ........... .............. ...... – 65°C to +150°C Ambient T emperature with Pow er Supplied Industrial ......... ........... ...

  • Cypress CY7C68053 - page 24

    CY7C68053 Document # 001-06120 Rev *F Page 24 of 39 8.0 DC Characteristics T able 8-1. DC Characteristics Parameter Description Conditions Min. Ty p . Ma x. Unit AV CC 3.3 V supply (to Osc. and PHY) [15] 3.00 3.3 3.60 V V CC_IO 1.8V to 3.3V supply (to I/O) 1.71 1.8 3.60 V V CC_A 1.8 V supply to Analog Core 1.71 1.8 1.89 V V CC_D 1.8 V supply to Dig ...

  • Cypress CY7C68053 - page 25

    CY7C68053 Document # 001-06120 Rev *F Page 25 of 39 9.0 AC Electrical Characteristics 9.1 USB T ransceiver USB 2.0-compliant in full- and high -speed modes. 9.2 GPIF Synchronous Signa ls 8 DATA(output) t XGD IFCLK RDY X DATA(input) valid t SRY t RYH t IFCLK t SGD CTL X t XCTL t DAH N N+1 GPIFADR[8:0] t SGA Figure 9-1. GPIF Sync hronous Signa ls Tim ...

  • Cypress CY7C68053 - page 26

    CY7C68053 Document # 001-06120 Rev *F Page 26 of 39 9.3 Slave FIFO Synchronous Read IFCLK SLRD FLAGS SLOE t SRD t RDH t OEon t XFD t XFLG DATA t IFCLK N+1 t OEoff N Figure 9-2. Slave FIFO Synchronou s Read Timing Diagram [17] T able 9-3. Slave FIFO Synchron ous Read Parameters with Interna lly Sourced IFCLK [18] Parameter Description Min. Max. Unit ...

  • Cypress CY7C68053 - page 27

    CY7C68053 Document # 001-06120 Rev *F Page 27 of 39 9.4 Slave FIFO Asynchronous Read SLRD FLAGS t RDpwl t RDpwh SLOE t XFLG t XFD DATA t OEon t OEoff N+1 N Figure 9-3. Sla ve FIFO Asynchrono us Read T iming Diagram [17] Note 20. Slave FIFO asynchronous pa rameter values use internal IFCLK setting at 48 MHz. T able 9-5. Slave FIFO Asynchrono us Read ...

  • Cypress CY7C68053 - page 28

    CY7C68053 Document # 001-06120 Rev *F Page 28 of 39 9.5 Slave FIFO Synchronous W rite Z Z t SFD t FDH DATA IFCLK SLWR FLAGS t WRH t XFLG t IFCLK t SWR N Figure 9-4. Slave FI FO Synchronous W rite T iming Dia gram [17] T able 9-6. Slave FIFO Synchronou s Write Parameters with Internally Sourced IFCLK [18] Parameter Description Min. Max. Unit t IFCLK ...

  • Cypress CY7C68053 - page 29

    CY7C68053 Document # 001-06120 Rev *F Page 29 of 39 9.6 Slave FIFO Asynchronous W rite 9.7 Slave FIFO Synchronous Packet End S trobe DATA t SFD t FDH FLAGS t XFD SLWR/SLCS# t WRpwh t WRpwl Figure 9-5. Slave FI FO Asynchronous Write T iming Diagram [17] T able 9-8. Slave FIFO Asynchrono us Write Parameters with Internally Sourced IFCLK [20] Paramete ...

  • Cypress CY7C68053 - page 30

    CY7C68053 Document # 001-06120 Rev *F Page 30 of 39 There is no specific timing requ irement that nee ds to be met for asserting the PKTEND pin with regards to asserting SL WR. PKTEND can be asserted with the last data value clocked into the FIFO’s or thereafter . The only consideration is that the set- up time t SPE and the hold time t PEH must ...

  • Cypress CY7C68053 - page 31

    CY7C68053 Document # 001-06120 Rev *F Page 31 of 39 9.9 Slave FIFO Output Enable 9.10 Slave FIFO Address to Flags/Dat a T able 9-12. Slave F IFO Output Enable Pa rameters Parameter Description Min. Max. Unit t OEon SLOE Assert to FIFO DA T A Outp ut 10.5 ns t OEoff SLOE Deassert to FIFO DA T A Hold 2.15 10.5 ns T able 9-13. Slave FIFO Address to Fl ...

  • Cypress CY7C68053 - page 32

    CY7C68053 Document # 001-06120 Rev *F Page 32 of 39 9.1 1 Slave FIFO Synchronous Address 9.12 Slave FIFO Asynchronous Address T able 9-14. Slave FIFO Synchronous Ad dress Parameters [10] Parameter Description Min. Max. Unit t IFCLK Interface Clock Period 20.83 200 ns t SF A FIFOADR[1:0] to Clock Set-up T ime 25 ns t FA H Clock to FIFOADR[1:0] Ho ld ...

  • Cypress CY7C68053 - page 33

    CY7C68053 Document # 001-06120 Rev *F Page 33 of 39 9.13 Sequence Diagram V arious sequence diagrams and examples are presented in this section. 9.13.1 Singl e and Burst Synchronous Read Example Figure 9-13 shows the timi ng relationship of the SLA VE FIFO signals during a synch ronous FIFO read using IFCLK as the synchronizing clock. T he diagram ...

  • Cypress CY7C68053 - page 34

    CY7C68053 Document # 001-06120 Rev *F Page 34 of 39 9.13.2 Singl e and Burst Synchronous Write Figure 9-15 shows the timi ng relationship of the SLA VE FIFO signals during a synchronous write using IFCLK as the synchronizing clock. The diagram illustrates a single write followed by burst write of 3 bytes and committing all 4 byte s as a short packe ...

  • Cypress CY7C68053 - page 35

    CY7C68053 Document # 001-06120 Rev *F Page 35 of 39 9.13.3 Seque nce Diagram of a Single and Burst Asynch ronous Read Figure 9-16 illustrates the timing rel ationship of the SLA VE FIFO signals during an asynchronous FIFO read. It shows a single read followed by a burst read. • At t = 0, the FIFO address is stable and the SLCS signal is asserted. ...

  • Cypress CY7C68053 - page 36

    CY7C68053 Document # 001-06120 Rev *F Page 36 of 39 9.13.4 Seque nce Diagram of a Single and Burst Asynch ronous Write Figure 9-18 illustrates the timing rel ationship of the SLA VE FIFO write in an asynchron ous mode. The diagram shows a single wri te followe d by a burst write of 3 bytes an d committing the 4-byte-short packet using PKTEND. • A ...

  • Cypress CY7C68053 - page 37

    CY7C68053 Document # 001-06120 Rev *F Page 37 of 39 10.0 Ordering Information 1 1.0 Package Diagram The FX2LP18 is a vailable in a 56-pin VFBGA package. Figure 1 1-1. 56 VFBGA (5 x 5 x 1.0 mm) 0.50 Pitch, 0.30 Ball BZ56 T able 10-1. Ordering Information Ordering Code Package T ype RAM Size # Prog I/Os 8051 Address/Data Busses CY7C68053-56BAXI 56 VF ...

  • Cypress CY7C68053 - page 38

    CY7C68053 Document # 001-06120 Rev *F Page 38 of 39 © Cypress Semi conductor Corpora tion, 2006. The i nformation cont ained here in is subject to ch ange withou t notice. Cypress S emic onductor Corporation assu mes no responsibility for the use of any circuitry o ther than circui try embodied i n a Cypress prod uct. Nor does it convey or imply a ...

  • Cypress CY7C68053 - page 39

    CY7C68053 Document # 001-06120 Rev *F Page 39 of 39 Document History Page Document Title: CY7C68053 MoBL-USB FX2LP18 USB Microcontroller Document Number: 001-06120 REV . ECN N O. Issue Date Orig. of Change Description of Change ** 430449 03 /03/06 OSG New data sheet *A 434754 03/24/06 OSG In Section 3. 3, stated that SCL and SDA pi ns can be connec ...

Fabricant Cypress Catégorie Computer Hardware

Les documents que nous recevons du fabricant de l'appareilCypress CY7C68053 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Cypress
- manuels d’utilisations CY7C68053
- fiches produit Cypress
- dépliants
- ou étiquettes-énergie Cypress CY7C68053
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Cypress CY7C68053.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Cypress CY7C68053, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Cypress CY7C68053. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Cypress CY7C68053.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Cypress CY7C68053, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Cypress CY7C68053 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Cypress CY7C68053.

Le manuel d’utilisation complet Cypress, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Cypress CY7C68053 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Cypress CY7C68053, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lCypress CY7C68053 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Cypress CY7C68053 - qui devraient nous aider dans les premières étapes lors de l'utilisation Cypress CY7C68053
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Cypress CY7C68053
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Cypress CY7C68053 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Cypress CY7C68053?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Cypress CY7C68053, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Cypress CY7C68053 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)