Français dropdown-ico

Manuel d’utilisation Yamaha WR450F (2010)

229 pages Non applicable
Télécharger

Aller à la page of 229

Summary
  • Yamaha WR450F (2010) - page 1

    O WNER’S SER VICE MANU AL MANUEL D’A TELIER DU PR OPRIET AIRE F AHRER- UND W AR TUNGSHANDB UCH MANU AL DE SER VICIO DEL PR OPIET ARI O WR450F ( Z ) 5TJ-28199-47 PRINTED IN JAP AN 2009.07—0.5 × 1 ! (E, F , G, S) Y AMAHA MO T OR CO . , L TD . 2500 SHINGAI IW A T A SHIZUOKA JAP AN PRINTED ON RECYCLED P APER 2010 WR450F ( Z ) 2010 q Read this ma ...

  • Yamaha WR450F (2010) - page 2

    Q Read this manual carefull y bef ore operating this vehicle. This manual should sta y with this vehicle if it is sold. Q Il con vient de lire attentivement ce manuel av ant la première utilisation du véhicule . Le manuel doit étre remis avec le véhicule en cas de vente de ce dernier . Q Bitte lesen Sie diese Bedienungsanleitung sorgfältig dur ...

  • Yamaha WR450F (2010) - page 3

    WR450F(Z) WR450F(Z) 2010 2010 5TJ-28199-47-E0 5TJ-28199-47-E0 OW NER’S SERVICE MANUAL OW NER’S SERVICE MANUAL Read this manual carefully before operating this vehicle. Read this manual carefully before operating this vehicle. ...

  • Yamaha WR450F (2010) - page 4

    ...

  • Yamaha WR450F (2010) - page 5

    WR450F (Z) OWNER'S SERVICE MANUAL ©2009 by Yamaha Motor Co., Ltd. 1st Edition, July 2009 All rights reserved. Any repr inting or unauthorized use wi thout the written permission of Yamaha Motor Co., Ltd. is expressly proh ibited. Printed in Japan ...

  • Yamaha WR450F (2010) - page 6

    FOREWORD INTRODUCTION Congratul ations on y our purchas e of a Yamaha WR series. This model is the culmination of Yama ha's vast ex- perience in the production of paceset- ting racing machines. It represents the highest grade of craftsmanship and reliability that have made Yama- ha a leader. This manual explain s operation, in- spection, basic ...

  • Yamaha WR450F (2010) - page 7

    • PROPERLY SECURE THE MA- CHINE BEFORE TRANSPORTING IT. When transporting the machine in another vehicle, alwa ys be sure it is properly secured and in an upright position and that the fuel cock is in the "OFF" position. Otherwise, fuel may leak out of the carburetor or fuel tank. F.I.M. MACHINE WEIGHTS (Except for Canada) Weights of ma ...

  • Yamaha WR450F (2010) - page 8

    HOW TO READ DESCRIPTIONS To help identify parts and clarify pro- cedure steps, there are exploded dia - grams at the start of each removal and disassembly section. 1. An easy-to-see exploded diagram "1" is provided for removal and disassembly jobs. 2. Numbers "2" are given in the or- der of the jobs in the exploded di- agram. A ...

  • Yamaha WR450F (2010) - page 9

    TABLE OF CONTENTS GENERAL INFORMATION 1 SPECIFICATIONS 2 REGULAR INSPECTION AND ADJUSTMENTS 3 TUNING 4 ENGINE 5 CHASSIS 6 ELECTRICAL 7 ...

  • Yamaha WR450F (2010) - page 10

    CONTENTS CHAPTER 1 GENERAL INFOR- MATION LOCATION OF IMPORTANT LABELS ..... 1-1 DESCRIPTION . ................ 1-5 CONSUMER INFORMATION................. 1-6 INCLUDED PARTS .......... 1-6 IMPORTANT INFORMATION................. 1-6 CHECKING OF CONNECTION .................. 1-7 SPECIAL TOOLS ............. 1-8 CONTROL FUNCTIONS ................... 1-12 ...

  • Yamaha WR450F (2010) - page 11

    1-1 LOCATION OF IMPORTANT LABELS GENERAL INFORMATION LOCATION OF IMPORTANT LABELS Please read the following importan t labels carefully before operating this vehicle. CANADA Essence super sans plomb seulement. 3FB-2415E-12 1 ...

  • Yamaha WR450F (2010) - page 12

    1-2 LOCATION OF IMPORTANT LABELS EUROPE ...

  • Yamaha WR450F (2010) - page 13

    1-3 LOCATION OF IMPORTANT LABELS AUS, NZ, ZA ...

  • Yamaha WR450F (2010) - page 14

    1-4 LOCATION OF IMPORTANT LABELS Familiarize yourself w ith the following pictograms and read the explanatory text. Read Owner's servic e manual. This unit contains high-pressure nitrogen ga s. Mishandling can cause explosion. Do not incinerate, puncture or open. Turn off the main switch after riding to avoid draining the battery. Use unleaded ...

  • Yamaha WR450F (2010) - page 15

    1-5 DESCRIPTION DESCRIPTION • The machine you have purchased may differ slightly from th ose shown in the following. • Designs and specifications are subj ect to change without notice. 1. Clutch lever 2. Hot starter lever 3. Engine stop switch 4. Multi-function displ ay 5. Main switch 6. Start switch 7. Front brake lever 8. Throttle grip 9. Rad ...

  • Yamaha WR450F (2010) - page 16

    1-6 CONSUMER INFORMATION CONSUMER INFORMATION There are two signi ficant reasons for knowing the serial number of your machine: 1. When ordering parts, you can give the number to your Yamaha dealer for positive identification of the model you own. 2. If your machine is stolen, the au- thorities will need the number to search for and identify your m ...

  • Yamaha WR450F (2010) - page 17

    1-7 CHECKING OF CONNECTION 3. When disassemblin g the ma- chine, keep mated pa rts together. They include gears, cylinders, pistons, and othe r mated parts that have been "mated" through normal wear. Mated parts must be reused as an assembly or re- placed. 4. During the machine disassembly, clean all parts and place them in trays in the o ...

  • Yamaha WR450F (2010) - page 18

    1-8 SPECIAL TOOLS SPECIAL TOOLS The proper spec ial tools are necessa ry for complete and accura te tune-up and assembly. Using the correct special tool will help prevent damage caused by the use of improper tools or improvised techni ques . The shape and part numb er used for the special tool differ by coun try, so two types are provided. Refer to ...

  • Yamaha WR450F (2010) - page 19

    1-9 SPECIAL TOOLS Damper rod holder YM-01494, 90890-01494 Use this tool to remove and install the damper rod. Fork seal driver YM-A0948, 90890-01502 This tool is used when install th e fork oil seal. Spoke nipple wrench YM-01521, 90980-01521 This tool is used to tighten the spoke. Sheave holder YS-1880-A, 90890-01701 This tool is used for when loos ...

  • Yamaha WR450F (2010) - page 20

    1-10 SPECIAL TOOLS Valve spring compressor YM-4019, 90890-04019 This tool is needed to remove and install the valve assembl ies. Clutch holding tool YM-91042, 90890-04086 This tool is used to hold the clutch when removing or installing the clutch boss securing nut. Valve guide remover Intake 4 .5 mm (0.18 in) Exhaust 5.0 mm (0.20 in) YM-4116, 90890 ...

  • Yamaha WR450F (2010) - page 21

    1-11 SPECIAL TOOLS Dynamic spark tester YM-34487 Ignition checker 90890-06754 This instrument is necessary for checking the ignition system compo- nents. Vacuum/pressure pump gaug e set YB-35956-A, 90890-06756 This tool is used to check the air in- duction system. Digital tachometer YU-39951-B, 90890-0676 0 This tool is needed for observing en- gin ...

  • Yamaha WR450F (2010) - page 22

    1-12 CONTROL FUNCTIONS CONTROL FUNCTIONS MAIN SWITCH Functions of the respective switch po- sitions are as follows: ON: The engine can be started only at this position. OFF: All electrical circuits are switched off. Main switch indicator light The main switch "1" is equipped with an indicator light "2" to avoid forget- ting to t ...

  • Yamaha WR450F (2010) - page 23

    1-13 MULTI-FUNCTION DISPLAY COLD STARTER KNOB When cold, the engine requires a richer air-fuel mixture for starting. A separate starter circuit, which i s con- trolled by the cold starter knob "1", supplies this mixture. Pull the cold starter knob out to open the circuit for starting. When the engine has warmed up, push it in to close the ...

  • Yamaha WR450F (2010) - page 24

    1-14 MULTI-FUNCTION DISPLAY Changing odomet er and tripmeter A/B (TRIP A/B) 1. Push the "SLCT2" button to change the tripmeter display. The display will change in the follow- ing order: Odometer → TRIP A → TRIP B → TRIP A → Odometer. To reset the digits, se lect the tripme- ter involved and push the "RST" but- ton for 2 ...

  • Yamaha WR450F (2010) - page 25

    1-15 MULTI-FUNCTION DISPLAY Auto start 1. Check that changeover has been made to RACE MODE. (Refer to "Changeover from BASIC MODE to RACE MODE".) 2. Make the machine ready for a run by pushing the "SLCT1" button for 2 seconds or more. When the measurement is made ready for a run by auto start, and will start flashing. Timer disp ...

  • Yamaha WR450F (2010) - page 26

    1-16 MULTI-FUNCTION DISPLAY FUNCTION DIAGRAM A short push on the button changes the operation in the arrowed direction. A short push on the button changes the operation in both arrowed directions. A long push on the button changes the operation in the arrowed direction. A long push on the button changes the operation in both arrowed directions. Met ...

  • Yamaha WR450F (2010) - page 27

    1-17 MULTI-FUNCTION DISPLAY The following diagram illustrates th e multi-function display rega rding the direction and operation condition in- volved in each of its functions. A. A short push on the button changes the operation i n the ar- rowed direction. B. A short push on the button changes the operation i n both arrowed di rections. C. A long p ...

  • Yamaha WR450F (2010) - page 28

    1-18 STARTING AND BREAK-IN STARTING AND BREAK-IN FUEL Always use the recommended fuel as stated below. Also, be sure to use new gasoline. Use only unleaded ga soline. The use of leaded gasoline will cause severe damage to the engi ne inter- nal parts such as valv es, piston rings, and exhaust system, etc. If knocking or pingi ng occurs, use a diffe ...

  • Yamaha WR450F (2010) - page 29

    1-19 STARTING AND BREAK-IN The engine fails to start Pull the hot starter lever all the way out and while holding the lever, kick the kickstarter crank 10 to 20 times to clear the engine. Then, re start the en- gine. Refer to "Restarting an engine after a fall". Observe the fo llowing break-in procedures during initia l operation to ensur ...

  • Yamaha WR450F (2010) - page 30

    1-20 TORQUE-CHECK POINTS TORQUE-CHECK POINTS Concerning the tightening torque, refer to "TIGHTENING TORQUES" section in the CHAPTER 2. Frame construction Frame to rear frame Combined seat and fuel tank Fuel tank to frame Exhaust system Silencer to rear frame Engine mounting Frame to engine Engine bracket to engine Engine bracket to frame ...

  • Yamaha WR450F (2010) - page 31

    1-21 CLEANING AND STORAGE CLEANING AND STORAGE CLEANING Frequent cleaning of your machine will enhance its appe arance, maintain good overall perfo rmance, and ex- tend the life of many components. 1. Before washing the machine, block off the en d of the exhau st pipe to prevent water from enter- ing. A plastic bag secured with a rubber band may be ...

  • Yamaha WR450F (2010) - page 32

    2-1 GENERAL SPECIFICATIONS SPECIFICATIONS GENERAL SPECIFICATIONS Model name: WR450FZ (USA, CDN, AUS, NZ) WR450F (EUROPE, ZA) Model code number: 5TJT (USA) 5TJU (CDN) 5TJV (EUROPE) 5TJW (AUS, NZ, ZA) Dimensions: USA, CDN, ZA EUROPE AUS, NZ Overall length 2,175 mm (85.63 in) 2,200 mm (86.61 in) 2,185 mm (86.02 in) Overall width 825 mm (32.48 in) ←? ...

  • Yamaha WR450F (2010) - page 33

    2-2 GENERAL SPECIFICATIONS Fuel: Type Premium unleaded gasoline on ly with a re search octane number of 95 or higher. Tank capacity 8.0 L (1.76 Imp gal, 2.11 US gal) Reserve 1.1 L (0.24 Imp ga l, 0.29 US gal) Carburet or: Type FCR-MX39 Manufacturer KEIHIN Spark plug: Type/manufacturer CR8E/NGK (resistance type ) Gap 0.7–0.8 mm (0.028–0.0 31 in) ...

  • Yamaha WR450F (2010) - page 34

    2-3 MAINTENANCE SPECIFICATIONS MAINTENANCE S PECIFICATIONS ENGINE Shock absorber: Front shock absorber Coil spring/oil damper Rear shock absorber Coil spring/gas, oil damper Wheel t ravel: Front wheel travel 300 mm (11.8 in) Rear wheel travel 305 mm (12.0 in) Electrical: Ignition system CDI Generator system AC magneto Battery type YTZ7S (F) Battery ...

  • Yamaha WR450F (2010) - page 35

    2-4 MAINTENANCE SPECIFICATIONS Intake "A" 3 0.100–30.200 mm (1.18 50–1.1890 in) 30.000 mm (1.1811 in) Intake "B" 2 2.450–22.550 mm (0.88 39–0.8878 in) 22.350 mm (0.8799 in) Exhaust "A" 30.200–30.300 mm (1.1890– 1.1929 in) 30.100 mm (1.1850 in) Exhaust "B" 22.450–22.550 mm (0.8839– 0.8878 in) 2 ...

  • Yamaha WR450F (2010) - page 36

    2-5 MAINTENANCE SPECIFICATIONS "D" margin thickness (IN) 1 mm (0.0394 in) 0.85 mm (0.033 in) "D" margin thickness (EX) 1 mm (0.0394 in) 0.85 mm (0.033 in) Stem outside diameter (IN) 4.475–4.490 mm (0 .1762–0.1768 in) 4.445 mm (0.1750 in) Stem outside diameter (EX) 4.96 5–4.980 mm (0.1955–0.1961 in) 4.9 35 mm (0.1943 in) ...

  • Yamaha WR450F (2010) - page 37

    2-6 MAINTENANCE SPECIFICATIONS Direction of winding (top view) (IN) Clockwise ---- Direction of winding (top view) (EX) Clo ckwise ---- Piston: Piston to cylinder clearance 0.020–0.04 5 mm (0.0008–0.0018 in) 0.1 mm (0.004 in) Piston size "D" 94.965–94.980 mm (3.7388– 3.7394 in) ---- Measuring poi nt "H" 8 mm (0.315 in) - ...

  • Yamaha WR450F (2010) - page 38

    2-7 MAINTENANCE SPECIFICATIONS Crankshaft: Crank width "A" 61.95–62.00 mm (2.439–2.441 in ) ---- Runout limit "C" 0.03 mm (0.0012 in) 0.05 mm (0.002 in) Big end side clearance "D" 0.15–0.45 mm (0.0059–0.0177 in) 0.50 mm (0.02 in) Small end free play "F" 0.4–1.0 mm (0.02–0.04 in) 2.0 mm (0.08 in) B ...

  • Yamaha WR450F (2010) - page 39

    2-8 MAINTENANCE SPECIFICATIONS Carburetor: USA, CDN, AUS, NZ, ZA EUROPE I. D. mark 5TJE E0 5TJL L0 ---- Main jet (M.J) #162 #160 ---- Main air jet (M.A.J) ø2.0 ← ---- Jet needle (J.N) NFNT NNHU ---- Cutaway (C.A) 1.5 ← ---- Pilot jet (P.J) #45 #48 ---- Pilot air jet (P.A.J) #70 ← ---- Pilot outlet (P.O) ø0.9 ← ---- Bypass (B.P) ø1.0 ← ...

  • Yamaha WR450F (2010) - page 40

    2-9 MAINTENANCE SPECIFICATIONS CHASSIS Item Standard Limit Steering system: Steering bearing type Taper roller bearing ---- Front suspension: USA, CDN EUROPE, AUS, NZ, ZA Front fork travel 300 mm (11.8 in) ← ---- Fork spring free length 460 mm (18.1 in) ← 455 mm (17.9 in) Spring rate, STD K = 4.5 N/mm (0.459 kg/ mm, 25.7 lb/in) ← ---- Optiona ...

  • Yamaha WR450F (2010) - page 41

    2-10 MAINTENANCE SPECIFICATIONS ELECTRICAL Drive chain: Type/manufacturer DID520VM/DAIDO ---- Number of links 113 links + joint ---- Chain slack 48–58 mm (1.9–2.3 in) ---- Chain length (15 links) ---- 239.3 mm (9.42 in) Front disc brake: Disc outside dia. × Thickness 250 × 3.0 mm (9.84 × 0.12 in) 250 × 2.5 mm (9.84 × 0.10 in) Pad thickness ...

  • Yamaha WR450F (2010) - page 42

    2-11 MAINTENANCE SPECIFICATIONS Charging system: System type AC magneto ---- Model (stator)/manufacture r 5TJ 50/YAMAHA ---- Normal output 14 V/120 W at 5,000 r/min ---- Charging coil resistance (color) 0.288–0.432 Ω at 20 °C (68 °F) (White–Ground) ---- Lighting coil resistance (color) 0.224–0.336 Ω at 20 °C (68 °F) (Yellow–Ground) -- ...

  • Yamaha WR450F (2010) - page 43

    2-12 TIGHTENING TORQUES TIGHTENING TORQUES ENGINE △ - marked portion shall be checked fo r torque ti ghtening after break-in or before each race. *1: Tighten the cylinder head bo lts to 30 Nm (3.0 m•kg, 22 ft•l b) in the proper tightening sequence, remo ve and retighten the cylinder head bolts to 20 Nm (2.0 m•kg, 14 ft•lb) in the proper t ...

  • Yamaha WR450F (2010) - page 44

    2-13 TIGHTENING TORQUES Radiator pipe 1, 2 M10 × 1.0 2 10 1.0 7.2 Impeller M8 × 1.25 1 14 1.4 10 Water pump housing cover M6 × 1.0 3 10 1.0 7.2 Coolant drain bol t M6 × 1.0 1 10 1.0 7.2 Oil pump cove r M4 × 0.7 1 2 0.2 1.4 Oil pump M6 × 1.0 2 10 1.0 7.2 Oil pump drive gear sha ft M6 × 1.0 1 10 1.0 7.2 Engine oil drain bolt (oil filter) M6 × ...

  • Yamaha WR450F (2010) - page 45

    2-14 TIGHTENING TORQUES CHASSIS △ - marked portion shall be checked fo r torque ti ghtening after break-in or before each race. Part to be tightened Thread size Q'ty Tightening torque Nm m•kg ft•lb △ Upper bracket and outer tube M8 × 1.25 4 21 2.1 15 △ Lower bracket and outer tube M8 × 1.25 4 21 2.1 15 △ Upper bracket and steeri ...

  • Yamaha WR450F (2010) - page 46

    2-15 TIGHTENING TORQUES △ Driven sprocket and wheel hub M8 × 1.25 6 50 5.0 36 △ Nipple (spoke) — 72 3 0.3 2.2 △ Disc cover and rear brake caliper M6 × 1.0 2 10 1.0 7.2 △ Protector and rear brake caliper M6 × 1.0 2 7 0.7 5.1 Chain puller adjust bolt and locknut M8 × 1.25 2 19 1.9 13 Engine mounting: △ Engine uppe r bracket and frame ...

  • Yamaha WR450F (2010) - page 47

    2-16 TIGHTENING TORQUES 1. First, tighten the steering ring nut app roximately 38 Nm (3.8 m•kg, 27 ft•lb) by us ing the steering nut wrench, then loosen the steering ring nut one turn. 2. Retighten the steering ring nut 7 Nm (0.7 m•kg, 5.1 ft•lb). ELECTRICAL Tighten the rotor nut to 65 Nm (6.5 m•k g, 47 ft•lb), loosen and retighten the ...

  • Yamaha WR450F (2010) - page 48

    2-17 TIGHTENING TORQUES GENERAL TORQUE SPECIFICA TIONS This chart specifies torque for stan- dard fasteners with standard I.S.O. pitch threads. Torque specifications for special components or assem- blies are included in the applicable sections of this book. To avoid war- page, tighten multi -fastener assem- blies in a crisscross fashion, in progre ...

  • Yamaha WR450F (2010) - page 49

    2-18 TIGHTENING TORQUES ...

  • Yamaha WR450F (2010) - page 50

    2-19 LUBRICATION DIAGRAMS LUBRICATION DIAGRAMS 1. Oil filter element 2. Oil pump 3. Drive axle 4. Main axle 5. Crankshaft 6. Connecting rod A. From cylinder B. To oil tank ...

  • Yamaha WR450F (2010) - page 51

    2-20 LUBRICATION DIAGRAMS 1. Intake camshaft 2. Exhaust camshaft A. To main axle B. From oil pump ...

  • Yamaha WR450F (2010) - page 52

    2-21 CABLE ROUTING DIAGRAM CABLE ROUTING DIAGRAM 1. Fuel tank breather hose 2. Clamp 3. Diode 4. Hot starter cable 5. Throttle position sensor lead 6. Wire harness 7. Hump (frame) 8. Negative battery lead 9. Starter motor lead 10. Neutral switch le ad 11. AC magneto lead 12. Brake hose 13. Rectifier/regulator lead 14. Carburetor breather hose 15. C ...

  • Yamaha WR450F (2010) - page 53

    2-22 CABLE ROUTING DIAGRAM A. Insert the end of the fuel ta nk breather hose into the hole in the steering stem. B. Fasten the throttle cable, hot starter cable and rectifier/regula - tor lead onto the frame. Locate the clamp under the throttle ca- ble on the right side of the frame, and face its ends, as well as the tie ends, dow nward. C. Fasten ...

  • Yamaha WR450F (2010) - page 54

    2-23 CABLE ROUTING DIAGRAM 1. Throttle cable (pull) 2. Throttle cable (return) 3. Catch tank hose 4. Ignition coil 5. Clamp 6. Air induction hose (air cut-off valve - rear of cylinder he ad) 7. Catch tank breather hose A. Cross the pull and push throttle cables. B. Fasten the catch tank ho se and air induction hose (air cut-off valve-rear of cylind ...

  • Yamaha WR450F (2010) - page 55

    2-24 CABLE ROUTING DIAGRAM 1. Brake ma ster cylinder 2. Brake hose holder 3. Brake ho se A. Install the brake hose so that its pipe portion directs as shown and lightly touche s the projec- tion on the brake caliper. B. Pass the brake hose into the brake hose holders. C. If the brake hose contacts the spring (rear shock absorber), correct its twist ...

  • Yamaha WR450F (2010) - page 56

    2-25 CABLE ROUTING DIAGRAM 1. Clamp 2. Positive battery lead 3. Battery 4. Negative battery lead 5. Taillight coupler 6. CDI unit coupler (6-pin) 7. CDI unit coupler (3-pin) 8. CDI unit coupler (6-pin) ...

  • Yamaha WR450F (2010) - page 57

    2-26 CABLE ROUTING DIAGRAM A. Fasten the wire harness to the upper engine bracket (left side). Locate the clamp end facing to- ward the upper side of the frame with the tie en d cu t off on the in- side of the frame. B. Fasten the wire harness to the upper engine bracket (left side). Locate the clamp end facing to- ward the upper side of the frame ...

  • Yamaha WR450F (2010) - page 58

    2-27 CABLE ROUTING DIAGRAM 1. Throttle cable 2. Clamp 3. Brake ho se 4. Clutch cable 5. Hose guide 6. Main switch coupler 7. Wire harness 8. Headlight coupler 9. Hot starter cable 10. Multi-function displ ay bracket 11. Main switch 12. Upper bracket 13. Clutch switch coupler 14. Engine stop switch coupler 15. Multi-function display cou pler 16. Sta ...

  • Yamaha WR450F (2010) - page 59

    2-28 CABLE ROUTING DIAGRAM A. Fasten the start switch lead to the handlebar with the plas tic bands. B. Fasten the engine stop switch lead and clutch switch lead to the handlebar with the plas tic bands. C. Pass the brake hose through the hose guides. D. Secure the coupl er by inserting it into the multi-function display bracket. E. Pass the thrott ...

  • Yamaha WR450F (2010) - page 60

    3-1 PERIODIC MAINTENANCE CHART FOR THE EMISSION CONTROL SYSTEM (For Canada) REGULAR INSPECTION AND ADJUSTMENTS PERIODIC MAINTENANCE CHART FO R THE EMISSION CONTRO L SYSTEM (For Canada) • From 4,200 mi (7,000 km) or 9 months, repeat the maintenanc e intervals starting from 1,800 mi (3,000 km) or 3 months. • Items marked w ith an asterisk should ...

  • Yamaha WR450F (2010) - page 61

    3-2 GENERAL MAINTENANCE AND LUBRICATION CHART (For Canada) GENERAL MAINTENANCE AND LUBRI CATION CHART (For Canada) No. ITEM CHECKS AND MAINTENANCE JOBS INITIAL ODOMETER READINGS 600 mi (1,000 km) or 1 month 1,800 mi (3,000 km) or 3 months 3,000 mi (5,000 km) or 6 months 1 Clutch Check operation. √√√ Adjust or repla ce cable. 2 * Co oling syst ...

  • Yamaha WR450F (2010) - page 62

    3-3 MAINTENANCE INTERVALS FOR COMPETITION USE • The air filter needs more fre quent service if you are riding in unusually wet or dusty areas. • Hydraulic brake service • After disasse mbling the brake master cylinders and calipers, always change the fluid. Regularly che ck the brake fluid levels and fill the reservoirs as required. • Every ...

  • Yamaha WR450F (2010) - page 63

    3-4 MAINTENANCE INTERVALS FOR COMPETITION USE VALVE LIFTERS Inspect ● Check for scratches and wear. Replace ● CAMSHAFTS Inspect the camshaft surface. Inspect ● Inspect the decompression system. Replace ● CAMSHAFT SPROCKETS Inspect ● Check for w ear on th e teeth and for damage. Replace ● PISTON Inspect ●● Inspect crack. Clean ● In ...

  • Yamaha WR450F (2010) - page 64

    3-5 MAINTENANCE INTERVALS FOR COMPETITION USE CRANK Inspect and clean ●● CARBURETOR Inspect, adjust and clean ●● AIR INDUCTION SYSTEM Inspect and clean ●● ●● SPARK PLUG Inspect and clean ●● Replace ● DRIVE CHAIN Use chain lube. Lubricat e, slack, ali gnment ●● Chain slack: 48–58 mm (1.9–2.3 in) Replace ● COOLING SYST ...

  • Yamaha WR450F (2010) - page 65

    3-6 MAINTENANCE INTERVALS FOR COMPETITION USE FRONT FORKS Inspect and adjust ●● Replace oil ●● Suspension oil "S1" Replace oil seal ● FRONT FORK OIL SEAL AND DUST SEAL Clean and lube ●● Li thium base grease PROTECTOR GUIDE Replace ● REAR SHOCK ABSORBER Inspect and adjust ●● Lube ● (After rain ride) ● Molybdenum dis ...

  • Yamaha WR450F (2010) - page 66

    3-7 PRE-OPERATION INSPECTION AND MAINTENANCE PRE-OPERATION INSPECTION AND MAINTENANCE Before riding for break-in operation or practice, make sure the machine is in goo d operating condition. Before using this machine, ch eck the following points. GENERAL INSPECTION AND MAINTENANCE Item Routine Page Coolant Check that coolant is fill ed up to the ra ...

  • Yamaha WR450F (2010) - page 67

    3-8 ENGINE ENGINE REMOVING THE SEAT, FUEL TANK AND SIDE COVERS Order Part name Q'ty Remarks Turn the fuel cock to "OFF". Disconnect the fuel hose. 1S e a t 1 2 Air scoop (left and right) 2 3 Bolt (fuel tank) 2 4 Fuel tank 1 5 Left side cover 1 Open the air filter case cover. 6 Right side cover 1 Refe r to removal section. 7 Headlight ...

  • Yamaha WR450F (2010) - page 68

    3-9 ENGINE REMOVING THE SIDE COVER 1. Remove: • Bolt (side cover) • Right side cover "1" Draw the side cover backward to re- move it because its claw "a" is insert- ed in the air filter case. ...

  • Yamaha WR450F (2010) - page 69

    3-10 ENGINE REMOVING THE EXHAUST PIPE AND SILENCER Order Part name Q'ty Remarks Right side cover Refer to "REMOVING THE SEAT, FUEL TANK AND SIDE COVERS" section. 1 Bolt (silencer clamp) 1 Onl y loosening. 2 Bolt [silencer (front)] 1 3 Bolt [silencer (rear)] 1 4 Collar 1 5 Silencer 1 6 Silencer clamp 1 7 Nut (exhaust pipe) 1 8 Bolt (e ...

  • Yamaha WR450F (2010) - page 70

    3-11 ENGINE CHECKING THE SILENCER AND EXHAUST PIPE 1. Inspect: • Gasket "1" Damage → Rep lace. INSTALLING THE SILENCER AND EXHAUST PIPE 1. Install: • Gasket • Exhaust pipe "1" • Nut (exhaust pipe) "2" • Bolt (exhaust pipe) "3" First, temporarily tighten the nut (ex- haust pipe), then tighten the b ...

  • Yamaha WR450F (2010) - page 71

    3-12 ENGINE Handling note s of coolant: The coolant is harmful so it should be handled with sp ecial care. • When coolant sp lashes to your eye. Thoroughly wash your eye with water and see your do ctor. • When coolant sp lashes to your clothes. Quickly wash it away with water and then with soap. • When coola nt is swallowe d. Quickly make him ...

  • Yamaha WR450F (2010) - page 72

    3-13 ENGINE 2. Adjust: • Throttle grip free play Throttle grip free play adjustm ent steps: a. Slide the adjuster cover. b. Loosen the locknut "1". c. Tu rn the adjuster "2" until the specified free play is obtained. d. Tighten the lockn ut. Before adjusting the th rottle cable free play, the engine idle speed should be adjust ...

  • Yamaha WR450F (2010) - page 73

    3-14 ENGINE 5. Inspect: • Air filter element Damage → Rep lace. 6. Apply: • Foam-air-filter oil or equivalent oil to the el ement • Squeeze out the excess oil. Ele- ment shoul d be wet but not drip - ping. • Wipe off the oil left on the element surface using a clean dry cloth. (Ex- cess oil in the element may ad- versely affect engine sta ...

  • Yamaha WR450F (2010) - page 74

    3-15 ENGINE CHANGING THE ENGINE OIL 1. Start the engine and let it warm up for several minutes. 2. Stop the engine and place an oil pan under the drain bolt. 3. Remove: • Engine guard "1" • Oil ta nk plug "2" • Oil filler cap "3" • Drain bolt (w ith gasket) "4" • Oil filter dr ain bolt (O -ring) &qu ...

  • Yamaha WR450F (2010) - page 75

    3-16 ENGINE Using a digital engine tachometer for idle speed adjustment, detect th e en- gine idling speed by bringing th e sensing element "c" of the engine ta- chometer close to the ignition coil "2". ADJUSTING THE VALVE CLEARANCE • This section is intended for those who have basic knowledge an d skill concerning the servici ...

  • Yamaha WR450F (2010) - page 76

    3-17 ENGINE c. Sele ct the proper pad using the pad selecting table. The thickness "a" of each pad is indi- cated in hundredths of milli meters on the pad upper surface. d. Round off the last digit of the in- stalled pad number to the nearest increment. EXAMPLE: Installed pad number = 148 Rounded off value = 150 Pads can only be selected ...

  • Yamaha WR450F (2010) - page 77

    3-18 ENGINE INTAKE EXHAUST MEASURED CLEARANCE INSTALLED PAD NUMBER 120 125 130 135 140 145 150 155 160 165 170 175 180 185 190 195 200 205 210 215 220 225 230 235 240 0.00 - 0.04 120 125 13 0 135 140 145 150 155 160 165 170 175 180 185 190 195 200 205 210 215 220 225 230 0.05 - 0.09 120 125 130 135 140 1 45 150 155 160 165 170 175 180 185 190 195 2 ...

  • Yamaha WR450F (2010) - page 78

    3-19 CHASSIS CLEANING THE SPARK ARRESTER (For USA) • Be sure the exhaust p ipe and si- lencer a re cool b efore clean ing the spark arre ster. • Do not start th e engine w hen cleaning the exhaus t system. 1. Remove: • Screw (silencer cap) "1" 2. Remove: • Bolt (spark arrester) "1" 3. Remove: • Tail pipe "1" ...

  • Yamaha WR450F (2010) - page 79

    3-20 CHASSIS 2. Remove: • Brake lever cover 3. Adjust: • Brake lever position Brake lever position adjustment steps: a. Loosen the locknut "1". b. Turn the adjusti ng bolt "2" until the lever position "a" is within speci- fied position. c. Ti ghten the locknut. Be sure to tighten the locknut, as it will cause poor ...

  • Yamaha WR450F (2010) - page 80

    3-21 CHASSIS i. Insta ll the brake caliper "8" and tighten the pad pin "9". j. Insta ll the pad pin plug "10". 3. Inspect: • Brake fluid level Refer to "CHECKING THE BRAKE FLUID LEVEL" section. 4. Check: • Brake lever operation A softy or spongy feeling → Bleed brake system. Refer to "BLEEDING THE ...

  • Yamaha WR450F (2010) - page 81

    3-22 CHASSIS 3. Inspect: • Brake fluid level Refer to "CHECKING THE BRAKE FLUID LEVEL" section. 4. Check: • Brake pedal operation A softy or spongy feeling → Bleed brake system. Refer to "BLEEDING THE HY- DRAULIC BRAKE SYSTEM" sec- tion. CHECKING THE REAR BRAKE PAD INSULATOR 1. Remove: • Brake pad Refer to "CHECKING ...

  • Yamaha WR450F (2010) - page 82

    3-23 CHASSIS When installing th e drive chain, apply the lithium soap base grease on th e chain joint and O-rings. 7. Install: • Link plate • Press the link plate onto the chain joint using a drive chain riveter "5". • Rivet the end of the ch ain joint us- ing a drive chai n riveter. • After riveting the chain joint, make sure its ...

  • Yamaha WR450F (2010) - page 83

    3-24 CHASSIS RELIEVING THE FRONT FORK INTERNAL PRESSURE If the front fork in itial movement feels stiff during a run, reli eve the front fork internal pressure. 1. Elevate the front wheel by placing a suitable stand under the engine. 2. Remove the air bleed screw "1" and release the internal pressure from the front fork. 3. Install: • A ...

  • Yamaha WR450F (2010) - page 84

    3-25 CHASSIS b. Loosen the adjuster "2" until there is some clearance between the spring and adjuster. c. Measure the spring free le ngth "a". d. Turn the adjuster "2". • Be sure to remove all dirt and mud from around the locknut and ad just- er before adjustment. • The length of the spring (installed) changes 1.5 ...

  • Yamaha WR450F (2010) - page 85

    3-26 CHASSIS ADJUSTING THE REAR SHOCK ABSORBER HIGH COMPRESSION DAMPING FORCE 1. Adjust: • High compression damping force By turning the adjuster "1". • STANDARD POSITION: This is the position which is back by the specific number of turns from the fully turned-in position. (Which align the punch mark "a" on the adjuster with ...

  • Yamaha WR450F (2010) - page 86

    3-27 CHASSIS 4. Adjust: • Steering ring nut Steering ring nut adjustment steps: a. Remove the headlight. b. Remove the handlebar a nd upper bracket. c. Lo osen the steering ring nut "1" using the steering nut wrench "2 ". d. Tighten the steering ring nut "3" using steering nut wrench "4". • Apply the lith ...

  • Yamaha WR450F (2010) - page 87

    3-28 CHASSIS LUBRI CATION To ensure smooth operation of all components, lubricate your machine during setup, afte r break-in, and after every ride. 1. Al l control cable 2. Clutch lever pivot 3. Sh ift pedal pivot 4. Footrest pivot 5. T hrottle-to-handlebar contact 6. D rive chain 7. T ube guide cable winding por- tion 8. T hrottle cable end 9. C l ...

  • Yamaha WR450F (2010) - page 88

    3-29 ELECTRICAL ELECTRICAL CHECKING THE SPARK PLUG 1. Remove: • Spark plug 2. Inspect: • Electrode "1" Wear/damage → Replace. • Insulator color "2" Normal condition is a medium to light tan color. Distinctly different color → Check the engine condition. When the engine runs for many hours at low speeds, the spark plug ...

  • Yamaha WR450F (2010) - page 89

    3-30 ELECTRICAL 3. Remove: • Battery band •B a t t e r y 4. Measure: • Battery charge Measurement steps: a. Connect a pocket tester "1" to the battery terminals. • The charge state of an MF battery can be checked by measuring its open-circuit voltage (i.e., the vol t- age when the positive terminal is disconnected). • No chargin ...

  • Yamaha WR450F (2010) - page 90

    3-31 ELECTRICAL Charging method using a va riable voltag e charger ...

  • Yamaha WR450F (2010) - page 91

    3-32 ELECTRICAL Charging method usin g a constant voltage ch arger ...

  • Yamaha WR450F (2010) - page 92

    3-33 ELECTRICAL 6. Install: •B a t t e r y • Battery band 7. Connect: • Battery leads (to the batte ry terminals) First, connect the positiv e lead "1", then the negative lead "2". 8. Check: • Battery terminals Dirt → Cle an with a wire brush. Loose connection → Connect properly. 9. Lubricate: • Battery terminal 10 ...

  • Yamaha WR450F (2010) - page 93

    3-34 ELECTRICAL ADJUSTING THE HEADLIGHT BEAMS 1. Adjust: • Headlight beam (vertically) Adjusting steps: a. Turn the adjusting screw "1" in di- rection "a" or "b". Direction "a" Headlight beam is raised. Direction "b" Headlight beam is lowered. ...

  • Yamaha WR450F (2010) - page 94

    4-1 ENGINE (Except for Canada) TUNING ENGINE (Except for Canada) CARBURETOR SETTING • The air/fuel mixture will vary de- pending on atmospheric conditi ons. Therefore, it is necessary to take into consideration the air pressure, ambient temperature, hu midity, etc., when adjusting the carburetor. • Perform a test run to check for prop - er engi ...

  • Yamaha WR450F (2010) - page 95

    4-2 ENGINE (Except for Canada) ADJUSTING THE PILOT JET The richness of the air-fuel mixture with the throttle open 1/4 or less can be set by adjusti ng the pilot jet "1 ". Effects of adjusting the pilot jet (reference) A. Idle B. Fully open 1. #48 2. #42 3. #45 ADJUSTING THE JET NEEDLE GROOVE POSITION Adjusting the jet needl e "1&quo ...

  • Yamaha WR450F (2010) - page 96

    4-3 ENGINE (Except for Canada) CARBURETOR SETTING PARTS Main jet Size Part number (-14943-) Rich #185 4MX-44 #182 4MX-94 #180 4MX-43 #178 4MX-93 #175 4MX-42 #172 4MX-92 #170 4MX-41 #168 4MX-91 #165 4MX-40 (STD) #162 4MX-90 *(STD) Lean #160 4MX-39 Pilot jet Size Part number (-14948-) Rich #55 4MX-09 #52 4MX-08 #50 4MX-07 *(STD) #48 4MX-06 (STD) Lean ...

  • Yamaha WR450F (2010) - page 97

    4-4 ENGINE (Except for Canada) EXAMPLES OF CARBURETOR SETTING DEPENDING ON SYMPTOM This shou ld be taken s imply for a n example . It is necessa ry to set the carburetor while checking the operating conditio ns of the engine. Symptom Setting Checking At full throttle Hard breathing Shearing noise Whitish spark plug ↓ Lean mixture Increase main je ...

  • Yamaha WR450F (2010) - page 98

    4-5 CHASSIS CHASSIS SELECTION OF THE SECONDARY REDUCTION RATIO (SPROCKET) <Requirement for selection of sec- ondary gear reduction ra tio> • It is generally said that the second- ary gear ratio should be reduced for a longer straight portion of a speed course and should be in creased for a course with many corners. Actual - ly, however, as ...

  • Yamaha WR450F (2010) - page 99

    4-6 CHASSIS A. Air spring characteristics in relation to oil l evel change B. Load C. Stroke 1. Max. oil level 2. Standard oil level 3. Min. oil level ADJUSTING THE SPRING PRELOAD The spring preload is adjusted by in- stalling the adjustment washer "1 " be- tween the fork spring "2" and damper rod "3". Do not install t ...

  • Yamaha WR450F (2010) - page 100

    4-7 CHASSIS CHOOSING SET LENGTH 1. Place a stand or bl ock under the engine to put the rear wheel above the floor, and measure the length "a" between the rear wheel axle center and the re ar fender holding bolt. 2. Remove the stand or bl ock from the engine and w ith a rider astride the seat, measure the sunken length "b" betwee ...

  • Yamaha WR450F (2010) - page 101

    4-8 CHASSIS • Extent of adjustment (spring pre- load) For the spring preload adjustment, re- fer to "ADJUSTING THE REAR SHOCK ABSORBER SPRING PRE- LOAD" in the C HAPTER 3. SPRING PART NUM- B E R (-22212-) Maximum Minimum 5UN-00 5UN-10 5UN-20 5UN-30 Position in which the spring is turned in 20 mm (0.79 in) from its free length. Position ...

  • Yamaha WR450F (2010) - page 102

    4-9 CHASSIS SUSPENSION SETTING (FRONT FORK) • If any of the following symptoms is experienced with the standard position as the base, make resetting by reference to the adjustment procedure gi ven in the same chart. • Before any change, set t he rear shock absorb er sunken length to the standard figure 90–100 mm (3.5–3.9 in). Symptom Sectio ...

  • Yamaha WR450F (2010) - page 103

    4-10 CHASSIS SUSPENSION SETTING (REAR SHOCK ABSORBER) • If any of the following symptoms is experienced with the standard position as the base, make resetting by reference to the adjustment procedure gi ven in the same chart. • Adjust the rebound damp ing in 2-click increments or decrements. • Adjust the low compression dampi ng in 1-click in ...

  • Yamaha WR450F (2010) - page 104

    5-1 RADIATOR ENGINE This section is intended for those who have basi c knowled ge and skill concerning the servicing of Yamaha motorcycles (e.g., Yamaha dealers, se rvice engineers, etc.) Those who have little knowledge and skill co ncerning servicing are request- ed not to undertake inspection , adjustment, disassemb ly, or reassembly only by refe ...

  • Yamaha WR450F (2010) - page 105

    5-2 RADIATOR 6 Radia tor hose 4 1 7 Pipe 2/O-ring 1/1 8 Catch tank hose 1 9 Left r adiator 1 10 Radiator hose 1 1 11 Pipe 1/O-ring 1/1 12 Catch tank brea ther hose 1 13 Catch tank 1 Order Part name Q'ty Remarks 5 ...

  • Yamaha WR450F (2010) - page 106

    5-3 RADIATOR HANDLING NOTE Do not remove the radiator cap when the engine and ra diator are hot. Scaldi ng hot fluid and steam may be blown out under pressure, which could ca use serious injury . When the engin e has cooled, open the radiator cap by th e following procedure: Place a thick rag, like a towel, over the radiator cap, sl owly rotate the ...

  • Yamaha WR450F (2010) - page 107

    5-4 CARBURETOR CARBURETOR REMOVING THE CARBURETOR Order Part name Q'ty Remarks Seat and fuel ta nk Refer to "REMOVING THE SEAT, FUEL TANK AND SIDE COVERS" section in the CHAPTER 3. Rear shock absorber Refer to "REAR SHOCK ABSORBER" sec- tion in the CHAPTER 6. 1C l a m p 2 2 Throttle position sensor lead coupler 1 3 Throttle ...

  • Yamaha WR450F (2010) - page 108

    5-5 CARBURETOR 13 Bracket (cylinde r head breather pipe) 1 14 Carb uretor joint 1 Order Part name Q'ty Remarks ...

  • Yamaha WR450F (2010) - page 109

    5-6 CARBURETOR DISASSEMBLING THE CARBURETOR Order Part name Q'ty Remarks 1 Carburetor breather hose 4 2 Valve lever housing cover 1 3 Screw (throttle shaft) 1 4 Throttle valve 1 5 Need le holder 1 6 Jet needle 1 7 Accelerator pump cover 1 8S p r i n g 1 9 Diaphragm (accelerator pump) 1 10 Air cut valve cover 1 11 Spring (air cut valve) 1 12 Di ...

  • Yamaha WR450F (2010) - page 110

    5-7 CARBURETOR 19 Main j et 1 20 Needle jet 1 21 Spacer 1 22 Pilot je t 1 23 Starter j et 1 24 Push rod 1 Pull the push rod. 25 Throttl e shaft assembly 1 26 Push rod link lever assembly 1 27 Pilot ai r jet 1 28 Cold sta rter plunger 1 Order Part name Q'ty Remarks ...

  • Yamaha WR450F (2010) - page 111

    5-8 CARBURETOR HANDLING NOTE Do not loosen th e screw (throttle position sensor) "1" except when changing the th rottle position sen- sor due to failur e because it will cause a drop in engine pe rfor- mance. REMOVING THE PILOT SCREW (For EUROPE) 1. Remove: • Pilot screw "1" To optimize th e fuel flow at a small throttle openi ...

  • Yamaha WR450F (2010) - page 112

    5-9 CARBURETOR e. If both are fine, adjust the float height by bending th e float tab "b" on the float. f. Recheck the float height. CHECKING THE FLOAT 1. Inspect: • Float "1" Damage → Rep lace. CHECKING THE STARTER PLUNGER 1. Inspect: • Cold starter plunger "1" • Hot starter plunger "2 " Wear/damage ...

  • Yamaha WR450F (2010) - page 113

    5-10 CARBURETOR • Apply th e fluorochemical grease on the bearings. • Fit the projection "a" on the throttle shaft assembly into the slot "b" in the throttle posit ion sensor. • Make sure the stopper "c" of the spring fits into the recess in the car- buretor . • Turn the throttle shaft assembly left while holdi ...

  • Yamaha WR450F (2010) - page 114

    5-11 CARBURETOR 16. Insta ll: • Jet needle "1" •C o l l a r " 2 " • Spring "3" • Needle ho lder "4" • Throttle valve plate "5" To throttle valve "6 ". 17. Insta ll: • Throttle valve assembly "1" • Screw (throttle sh aft) "2" Install the valve lever rollers ...

  • Yamaha WR450F (2010) - page 115

    5-12 CARBURETOR 5. Install: • Throttle cable (pull) "1" • Throttle cable (return) "2" 6. Adjust: • Throttle grip free play Refer to "ADJUSTING THE THROTTLE CABLE FREE PLAY" section in the CHAPTER 3. 7. Install: • Throttle cable cover "1" • Bolt (throt tle cable cover) "2" 8. Install: • T ...

  • Yamaha WR450F (2010) - page 116

    5-13 AIR INDICTOIN SYSTEM AIR INDICTOIN SYSTEM REMOVING THE AIR INDUCTION SYSTEM Order Part name Q'ty Remarks 1 Bracket 1 2 Air cut-off valve assembly 1 3 Air induction hose (ai r cut-off valve - front of cyl- inder head) 1 4 Air induction pipe 1 5 Gasket 1 6 Air induction hose (air cut-off valve - rear of cylin- der head) 1 7 Air induction ho ...

  • Yamaha WR450F (2010) - page 117

    5-14 AIR INDICTOIN SYSTEM CHECKING THE AIR INDUCTION SYSTEM 1. Inspect: • Air induction hose Crack/damage → Rep lace. • Air induction pip e Crack/damage → Rep lace. 2. Check: • Operation of air cut valve Pass air through the pipe and check the air cut valve for opera- tion. Does not meet the followi ng con- dition → Rep lace the air cut ...

  • Yamaha WR450F (2010) - page 118

    5-15 CAMSHAFTS CAMSHAFTS REMOVING THE CYLINDER HEAD COVER Order Part name Q'ty Remarks Seat and fuel ta nk Refer to "REMOVING THE SEAT, FUEL TANK AND SIDE COVERS" section in the CHAPTER 3. Air cut-off valve assembly Refer to "AIR INDUCTION SYSTEM" section. Engine upper bracket (right) Refer to "ENGINE REMOVAL" se ...

  • Yamaha WR450F (2010) - page 119

    5-16 CAMSHAFTS REMOVING THE CAMSHAFTS Order Part name Q'ty Remarks 1 Timing mark accessing screw 1 Refer to removal section. 2 Crankshaft end accessing screw 1 Refer to removal section. 3 Timing chain tensioner cap bolt 1 Refer to removal section. 4 Timing chain tensioner 1 Refer to remova l section. 5 Gasket 1 Refer to removal section. 6 Bolt ...

  • Yamaha WR450F (2010) - page 120

    5-17 CAMSHAFTS REMOVING THE CAMSHAFT 1. Remove: • Timing mark accessing screw "1" • Crankshaft end acce ssing screw "2" 2. Align: • T.D.C. mark With align mark. Checking steps: a. Turn the crankshaft counterclock- wise with a wren ch. b. Align the T.D.C. mark "a" on the rotor with the align mark "b" on ...

  • Yamaha WR450F (2010) - page 121

    5-18 CAMSHAFTS 3. Measure: • Runout (camshaft) Out of specification → Replace. 4. Measure: • Camshaft-to-cap clearance Out of specification → Measure camshaft outside diamete r. Measurement steps: a. Install the camshaft onto the cylin- der head. b. Position a strip of Pl astigauge ® "1" onto the camshaft. c. Install the clip, do ...

  • Yamaha WR450F (2010) - page 122

    5-19 CAMSHAFTS INSTALLING THE CAMSHAFT 1. Install: • Exhaust camshaft "1" • Intake camshaft "2" Installation steps: a. Turn the crankshaft counterclock- wise with a wren ch. • Apply the moly bdenum disulfide oil on the camshafts. • Apply the engine oil on the decom- pression system. b. Align the T.D.C. mark "a" ...

  • Yamaha WR450F (2010) - page 123

    5-20 CYLINDER HEAD CYLINDER HEAD REMOVING THE CYLINDER HEAD Tighten the cylinder head bolts to 30 Nm (3.0 m•kg, 22 ft•lb ) in the proper ti ghtening sequenc e, remove and retighten the cylinder head bolts to 20 Nm (2.0 m•kg , 14 ft•lb) in the proper tightening sequence, and then tighten the cylinder head bolts further to reach the specified ...

  • Yamaha WR450F (2010) - page 124

    5-21 CYLINDER HEAD CHECKING THE CYLINDER HEAD 1. Eliminate: • Carbon deposits (from the com- bustion chambers) Use a rounded scraper. Do not use a sharp instrument to avoid damaging or scratching: • Spark plug threads • Valve seats 2. Inspect: • Cylinder head Scratches/damage → Replace. Replace the titanium valves with the cylinder head. ...

  • Yamaha WR450F (2010) - page 125

    5-22 CYLINDER HEAD 3. Install: • Bolt (cylinder head) "1" Bolt (cylinder head): 10 Nm (1.0 m•kg, 7.2 ft•lb) ...

  • Yamaha WR450F (2010) - page 126

    5-23 VALVES AND VALVE SPRINGS VALVES AND VALVE SPRINGS REMOVING THE VALVES AND VALVE SPRINGS Order Part name Q'ty Remarks Cylinder head Refer to "CYLINDER HEAD" section. 1 Valve lifter 5 Refer to removal section. 2 Adjusting pad 5 Refer to removal section. 3 Valve cotter 10 Refer to removal section. 4 Valve spring retainer 5 5 Valve ...

  • Yamaha WR450F (2010) - page 127

    5-24 VALVES AND VALVE SPRINGS REMOVING THE VALVE LIFTER AND VALVE COTTER 1. Remove: • Valve lifter "1" • Pad "2" Identify each lifter "1" and pad "2" po- sition very carefully so that they can be reinstalled in their original place. 2. Check: • Valve sealing Leakage at the valve seat → In- spect the v ...

  • Yamaha WR450F (2010) - page 128

    5-25 VALVES AND VALVE SPRINGS 4. Measure: • Margin thickness "a" Out of specification → Replace. 5. Measure: • Runout (valve stem) Out of specification → Replace. • When installin g a new valve always replace the guide. • If the valve is removed or replaced always replace the oil seal. 6. Eliminate: • Carbon deposits (from t ...

  • Yamaha WR450F (2010) - page 129

    5-26 VALVES AND VALVE SPRINGS h. Press the valve thro ugh the valve guide and onto the valve seat to make a clear pattern. i. Measure the valve seat width again. If the valve seat width is out of specification, reface and relap the valve seat. CHECKING THE VALVE SPRINGS 1. Measure: • Valve spring free leng th "a" Out of specification ? ...

  • Yamaha WR450F (2010) - page 130

    5-27 CYLINDER AND PISTON CYLINDER AND PISTON REMOVING THE CYLINDER AND PISTON Order Part name Q'ty Remarks Cylinder head Refer to "CYLINDER HEAD" section. 1 Bolt (cylinder) 1 2 Cylinder 1 3 Gasket 1 4 Dowel pin 2 5 Piston pin clip 2 Refer to removal section. 6 Piston pin 1 Refer to removal section. 7 Piston 1 Refer to removal section ...

  • Yamaha WR450F (2010) - page 131

    5-28 CYLINDER AND PISTON REMOVING THE PISTON AND PISTON RING 1. Remove: • Piston pin clip "1" • Piston pin "2" • Piston "3" • Put identification marks on ea ch piston head for reference during re- installation. • Before removing each piston pin, deburr the clip groove and pin hole area. If the piston pin groo ...

  • Yamaha WR450F (2010) - page 132

    5-29 CYLINDER AND PISTON 3. Measure: • Ring end gap Out of specification → Replace. You cannot measure the end gap on the expander spacer of the oil control ring. If the oil control ring rails show excessive gap, replace all three rings. CHECKING THE PISTON PIN 1. Inspect: • Piston pin Blue discoloration/gro oves → Re- place, then inspect t ...

  • Yamaha WR450F (2010) - page 133

    5-30 CLUTCH CLUTCH REMOVING THE CLUTCH Order Part name Q'ty Remarks Drain the engine oil . Refer to "CHANGING THE ENGINE OIL" section in the CHAPTER 3. Brake pedal Refer to "ENGINE REMOVAL" secti on. Clutch cable Disconnect at eng ine side. 1 Clutch cover 1 2 Gasket 1 3 Dowel pin 2 4 Clutch spring 6 5 Pressure plate 1 6 Pus ...

  • Yamaha WR450F (2010) - page 134

    5-31 CLUTCH 14 Nut (clutch boss) 1 Refer to removal section. 15 Lock wa sher 1 Refer to removal section. 16 Clutch boss 1 Refer to removal section. 17 Thrust washer 1 18 Primary driven gear 1 19 Push lever shaft 1 Order Part name Q'ty Remarks ...

  • Yamaha WR450F (2010) - page 135

    5-32 CLUTCH REMOVING THE CLUTCH BOSS 1. Remove: •N u t " 1 " • Lock washer "2" • Clutch boss "3 " Straighten the lock washer tab and use the clutch holding tool "4" to hold the clutch boss. A. For USA and CDN B. Except for USA and CDN CHECKING THE CLUTCH HOUSING AND BOSS 1. Inspect: • Clutch housing & ...

  • Yamaha WR450F (2010) - page 136

    5-33 CLUTCH 2. Install: • Lock washer "1" • Nut (clutch boss) " 2" Make sure to tighten to specifica- tion; otherw ise, it may damage the other part that is fastened togeth- er. • Install the lock washer with its con- caves fitted over the convexes of the clutch boss. • Use the clutch holding tool "3" to hold t ...

  • Yamaha WR450F (2010) - page 137

    5-34 OIL FILTER ELEMENT AND WATER PUMP OIL FILTER ELEMENT AND WATER PUMP REMOVING THE OIL FILTER ELEMENT AND WATER PUMP Order Part name Q'ty Remarks Right engine guard Refer to "ENGINE REMOVAL" section. Drain the engine oil . Refer to "CHANGING THE ENGINE OIL" section in the CHAPTER 3. Drain the coolant. Refer to "CHAN ...

  • Yamaha WR450F (2010) - page 138

    5-35 OIL FILTER ELEMENT AND WATER PUMP 9 Gasket 1 10 Dowel pin /O-ring 3/1 11 Impeller 1 Refer to removal section. 12 Washer 1 Refer to removal section. 13 Impeller shaft 1 Refer to removal section. 14 Oil seal 1 1 Refer to remova l section. 15 Oil seal 2 1 Refer to remova l section. 16 Bearing 1 Refer to removal section. Order Part name Q'ty ...

  • Yamaha WR450F (2010) - page 139

    5-36 OIL FILTER ELEMENT AND WATER PUMP REMOVING THE IMPELLER SHAFT 1. Remove: • Impelle r "1" • Washer "2" • Impeller sha ft "3" Hold the impeller shaft on its width across the flats "a" with spanners, etc. and remove the impeller. REMOVING THE OIL SEAL It is not necessary to disassemble the water pump, ...

  • Yamaha WR450F (2010) - page 140

    5-37 OIL FILTER ELEMENT AND WATER PUMP 2. Install: • Right crankcase cover "1" •B o l t " 2 " •B o l t • Apply the engin e oil on the impeller shaft end. • When installing the crankcase cov- er onto the crankca se, be sure that the impeller shaft end "2" aligns with the balancer end slot "3". • Ti ...

  • Yamaha WR450F (2010) - page 141

    5-38 BALANCER BALANCER REMOVING THE BALANCER Order Part name Q'ty Remarks Primary driven gear Refer to "CLUTCH" secti on. Right crankcase cover Refer to "OIL FILTER ELEMENT AND WA- TER PUMP" section. Stator Refer to "CDI MAGNETO" section. 1 Nut (balancer) 1 Refer to removal section. 2 Nut (primary drive gear) 1 R ...

  • Yamaha WR450F (2010) - page 142

    5-39 BALANCER REMOVING THE BALANCER 1. Straighten the lock wa sher tab. 2. Loosen: • Nut (balancer) "1" • Nut (primary drive gear) "2" • Nut (balancer shaft driven gear) "3" Place an aluminum plate "a" b etween the teeth of the balancer shaft drive gear "4" and driven gear "5". CHECK ...

  • Yamaha WR450F (2010) - page 143

    5-40 OIL PUMP OIL PUMP REMOVING THE OIL PUMP Order Part name Q'ty Remarks Primary driven gear Refer to "CLUTCH" section. Right crankcase cover Refer to "OIL FILTER ELEMENT AND WA- TER PUMP" section. 1 Circlip 1 2 Washer 1 3 Oil pump drive gear 1 4 Oil pump assembly 1 5 Dowel pin 2 6 Outer rotor 2 1 7 Circlip 1 8 Inner rotor ...

  • Yamaha WR450F (2010) - page 144

    5-41 OIL PUMP 15 Oil pump drive shaft 1 16 Rotor ho using 1 Order Part name Q'ty Remarks ...

  • Yamaha WR450F (2010) - page 145

    5-42 OIL PUMP CHECKING THE OIL PUMP 1. Inspect: • Oil pump drive gear • Oil pump drive shaft • Rotor housing • Oil pump cover Cracks/wear/damage → R eplace. 2. Measure: • Tip clearance "a" (between the inner rotor "1" and outer rotor "2") • Side clearanc e "b" (between the outer rotor "2&qu ...

  • Yamaha WR450F (2010) - page 146

    5-43 KICK SHAFT AND SHIFT SHAFT KICK SHAFT AND SHIFT SHAFT REMOVING THE KICK SHAFT AND SHIFT SHAFT Order Part name Q'ty Remarks Oil pump Refer to "OIL PUMP" section. 1 Kick idle gear 1 2 Kick shaft assembly 1 Ref er to removal section. 3 Spring guide 1 4 Torsion spring 1 5 Ratch et wheel 1 6 Kick gear 1 7 Kick shaft 1 8 Washer 1 9 Sh ...

  • Yamaha WR450F (2010) - page 147

    5-44 KICK SHAFT AND SHIFT SHAFT 17 Pawl 2 18 Pawl p in 2 19 Spring 2 20 Bolt (stopper leve r) 1 21 Stopper l ever 1 22 Torsion spring 1 23 Segment 1 Refer to removal section. Order Part name Q'ty Remarks ...

  • Yamaha WR450F (2010) - page 148

    5-45 KICK SHAFT AND SHIFT SHAFT REMOVING THE KICK SHAFT ASSEMBLY 1. Remove: • Kick shaft assembly "1" Unhook the torsion spring "2" from the hole "a" in the crankcase. REMOVING THE SHIFT GUIDE AND SHIFT LEVER ASSEMBLY 1. Remove: • Bolt (shift guide) • Shift guid e "1" • Shift lever assembly "2&qu ...

  • Yamaha WR450F (2010) - page 149

    5-46 KICK SHAFT AND SHIFT SHAFT INSTALLING THE SHIFT GUIDE AND SHIFT LEVER ASSEMBLY 1. Install: • Spring "1" • Pawl pin "2" •P a w l " 3 " To shift lever "4". Apply the engine oil on the spring, pawl pin and p awl. 2. Install: • Shift lever assembly "1" To shift guide "2". 3. Insta ...

  • Yamaha WR450F (2010) - page 150

    5-47 KICK SHAFT AND SHIFT SHAFT INSTALLING THE KICK IDLE GEAR 1. Install: • Kick idle gear "1" • Washer "2" • Circlip "3" • Apply th e engine oil on the kick idle gear inner circumference. • Install th e kick idle gear with its de- pressed side "a " toward you. ...

  • Yamaha WR450F (2010) - page 151

    5-48 AC MAGNETO AND STARTER CLUTCH AC MAGNETO AND STARTER CLUTCH REMOVING THE AC MAGNETO AND STARTER CLUTCH Order Part name Q'ty Remarks Drain the engine oil . Refer to "CHANGING THE ENGINE OIL" section in the CHAPTER 3. Seat and fuel ta nk Refer to "REMOVING THE SEAT, FUEL TANK AND SIDE COVERS" section in the CHAPTER 3. Di ...

  • Yamaha WR450F (2010) - page 152

    5-49 AC MAGNETO AND STARTER CLUTCH Tighten the rotor nut to 65 Nm (6.5 m•kg, 47 ft•lb), loosen and retighten th e rotor nut to 65 Nm (6.5 m•kg, 47 ft•lb). 12 Woodruff key 1 13 Starter clutch assembly co ver 1 Refer to removal section. 14 Starter clutch 1 Refer to removal section. 15 Starter clu tch drive gear 1 16 Holder 1 17 Pickup coil 1 ...

  • Yamaha WR450F (2010) - page 153

    5-50 AC MAGNETO AND STARTER CLUTCH REMOVING THE ROTOR 1. Remove: • Nut (rotor) " 1" • Washer Use the sheave holder "2". 2. Remove: • Rotor "1" Use the rotor puller "2". REMOVING THE STARTER CLUTCH 1. Remove: • Starter clutch a ssembly cover "1" Insert a thin screwdriver or the like under the ...

  • Yamaha WR450F (2010) - page 154

    5-51 AC MAGNETO AND STARTER CLUTCH • Pass the AC magn eto lead "5" un- der the pickup coil. • Pass the AC magn eto lead "4" un- der the holder as shown. • Take care not to catch the AC mag- neto lead between crankcase cover ribs. • Tighten the bolt (sta tor) using the T25 bit. • Apply the sealant to the grommet of the ...

  • Yamaha WR450F (2010) - page 155

    5-52 AC MAGNETO AND STARTER CLUTCH 10. Insta ll: • Cover (idle gear 1) "1" •B o l t " 2 " Install the co ver (idle gear 1) with its mark "a" facing upw ard. 11. Con nect: • AC magne to lead Refer to "CABLE R OUTING DIA- GRAM" section in the CHAPTER 2. 12. Insta ll: • Shift pedal " 1" • Bol ...

  • Yamaha WR450F (2010) - page 156

    5-53 ENGINE REMOVAL ENGINE REMOVAL REMOVING THE ENGINE Order Part name Q'ty Remarks Hold the machine by placing the suitable stand under the frame. Refer to "HANDLING NOTE". Drain the engine oil . Refer to "CHANGING THE ENGINE OIL" section in the CHAPTER 3. Seat and fuel ta nk Refer to "REMOVING THE SEAT, FUEL TANK AND ...

  • Yamaha WR450F (2010) - page 157

    5-54 ENGINE REMOVAL Ignition coil Disconnect the AC magneto lead. Disconnect the starter motor lead. Refer to "ELECTRIC STARTING SYSTEM" section in the CHAPTER 7. Negative battery lead Disconnect at the engine side. 1 Engine guard 1 2 Neutr al switch 1 3 Drive chain sprocket cover 1 4 Nut (drive sprocket) 1 Ref er to removal section. 5 Lo ...

  • Yamaha WR450F (2010) - page 158

    5-55 ENGINE REMOVAL HANDLING NOTE Support the machine securely so there is no dange r of it falling over. REMOVING THE DRIVE SPROCKET 1. Remove: • Nut (drive sprocket) "1" • Lock washer "2" • Straighten the lock wa sher tab. • Loosen the nut while applying the rear brake. 2. Remove: • Drive sprocket "1" • D ...

  • Yamaha WR450F (2010) - page 159

    5-56 ENGINE REMOVAL • Nut (drive sprocket) "2" Tighten the nut while applying the rear brake. Make sure to tighten to specifica- tion; otherw ise, it may damage the other part that is fastened togeth- er. 3. Bend the lock washer tab to lock the nut. 4. Install: • Drive chain sprocket guide • Drive chain sp rocket cover "1" ...

  • Yamaha WR450F (2010) - page 160

    5-57 CRANKCASE AND CRANKSHAFT CRANKCASE AND CRANKSHAFT REMOVING THE CRANKSHAFT Order Part name Q'ty Remarks Engine Refer to "ENGINE REMOVAL" section. Piston Refer to "CYLINDE R AND PISTON" section. Balancer Refer to "BALANCER" section. Kick shaft assembly Refer to "KICK SHAFT AND SHIFT SHAFT" section. Se ...

  • Yamaha WR450F (2010) - page 161

    5-58 CRANKCASE AND CRANKSHAFT 9 Left crankcase 1 Refer to removal section. 10 Oil strainer 1 11 Balancer shaft 1 Refer to removal section. 12 Crankshaft 1 Refer to remova l section. Order Part name Q'ty Remarks ...

  • Yamaha WR450F (2010) - page 162

    5-59 CRANKCASE AND CRANKSHAFT REMOVING THE CRANKCASE BEARING Order Part name Q'ty Remarks Transmission Refer to "TRANSMISSION, SHIFT CAM AND SHIFT FORK" section. Shift cam and shift fork Refer to "TRANSMISSION, SHIFT CAM AND SHIFT FORK" section. 1 Oil seal 3 2 Bearing 10 Refer to remova l section. ...

  • Yamaha WR450F (2010) - page 163

    5-60 CRANKCASE AND CRANKSHAFT DISASSEMBLING THE CRANKCASE 1. Separate: • Right crankca se • Left crankcase Separation steps: a. Remove the crankcase bolts, hose guide an d clutch cable hold- er. Loosen each bolt 1/4 of a turn at a time and after all the bolts are loos- ened, remove them. b. Remove the right crankcase. • Place the crankcase wi ...

  • Yamaha WR450F (2010) - page 164

    5-61 CRANKCASE AND CRANKSHAFT CHECKING THE CRANKSHAFT 1. Measure: • Runout limit "a" • Small end free play limit "b" • Connecting rod big end side clearance "c" • Crank widt h "d" Out of specification → Replace. Use the dial gauge and a thick- ness gauge. CHECKING THE OIL STRAINER 1. Inspect: • Oi ...

  • Yamaha WR450F (2010) - page 165

    5-62 CRANKCASE AND CRANKSHAFT 4. Apply: • Sealant On the right crankc ase. Clean the contacting surface of left and right crankcase before applying the sealant. 5. Install: • Dowel pin "1" • O-ring "2" • Right crankca se To left crankcase. • Apply the lithiu m soap base grease on the O-ring. • Fit the ri ght crankcas ...

  • Yamaha WR450F (2010) - page 166

    5-63 TRANSMISSION, SHIFT CAM AND SHIFT FORK TRANSMISSION, SHIFT CAM AND SHIFT FORK REMOVING THE TRANSMISSION, SHIFT CAM AND SHIFT FORK Order Part name Q'ty Remarks Engine Refer to "ENGINE REMOVAL" section. Separate the crankcase. Refer to "CRANKCASE AND CRANK- SHAFT" section. 1 Main axle 1 Refer to removal section. 2 Drive ...

  • Yamaha WR450F (2010) - page 167

    5-64 TRANSMISSION, SHIFT CAM AND SHIFT FORK REMOVING THE TRANSMISSION 1. Remove: • Main axle "1" • Drive axle "2" • Shift cam • Shift fork 3 • Shift fork 2 • Shift fork 1 • Remove assemb ly with the collar "3" installed to the crankcase. • Remove assembly carefully. Note the position of each part. Pay p ...

  • Yamaha WR450F (2010) - page 168

    5-65 TRANSMISSION, SHIFT CAM AND SHIFT FORK 3. Install: • Washer "1" • Circlip "2" • Be sure the circlip sharp-edged cor- ner "a" is po sitioned opposi te side to the washer and gear "b". • Install the circlip with its ends "c" settled evenly on the spline crests. 4. Install: •C o l l a r ...

  • Yamaha WR450F (2010) - page 169

    6-1 FRONT WHEEL AND REAR WHEEL CHASSIS This section is intended for those who have basi c knowled ge and skill concerning the servicing of Yamaha motorcycles (e.g., Yamaha dealers, se rvice engineers, etc.) Those who have little knowledge and ski ll concerning servicing are request- ed not to undertake inspection , adjustment, disassemb ly, or reas ...

  • Yamaha WR450F (2010) - page 170

    6-2 FRONT WHEEL AND REAR WHEEL REMOVING THE REAR WHEEL Order Part name Q'ty Remarks Hold the machine by placing the suitable stand under the engine. Refer to "HANDLING NOTE". 1 Nut (rear wheel axle) 1 2 Rear whe el axle 1 3 Drive chain puller 2 4 Rear wheel 1 Refer to removal section. 5 Collar 2 6 Rear wheel sprocket 1 7 Oil seal 2 8 ...

  • Yamaha WR450F (2010) - page 171

    6-3 FRONT WHEEL AND REAR WHEEL HANDLING NOTE Support the machine securely so there is no dange r of it falling over. REMOVING THE REAR WHEEL 1. Remove: • Wheel "1" Push the wheel forward and remove the drive chain "2". REMOVING THE WHEEL BEARING 1. Remove: • Bearing "1" Remove the bearing using a general bearing pu ...

  • Yamaha WR450F (2010) - page 172

    6-4 FRONT WHEEL AND REAR WHEEL 2. Install: • Brake disc "1" • Bolt (brake disc) "2" Tighten the bolts in stage, using a crisscross pattern. 3. Install: •C o l l a r " 1 " Apply the lithium soap base grease on the oil seal lip. 4. Install: • Speed sensor "1" • Apply the lithiu m soap base grease on t ...

  • Yamaha WR450F (2010) - page 173

    6-5 FRONT WHEEL AND REAR WHEEL 2. Install: • Brake disc "1" • Bolt (brake disc) "2" Tighten the bolts in stage, using a crisscross pattern. 3. Install: • Rear wheel sprocket "1" • Bolt (rear wheel sprocket) "2" • Washer (rear wheel spro cket) "3" • Nut (rear wheel sprocket) "4" ...

  • Yamaha WR450F (2010) - page 174

    6-6 FRONT BRAKE AND REAR BRAKE FRONT BRAKE AND REAR BRAKE REMOVING THE FRONT BRAKE Order Part name Q'ty Remarks Hold the machine by placing the suitable stand under the engine. Refer to "HANDLING NOTE". Drain the brake fluid. Refer to removal section. 1 Brake hose hold er (protector) 2 2 Brake hose hold er (brake caliper) 1 3 Union b ...

  • Yamaha WR450F (2010) - page 175

    6-7 FRONT BRAKE AND REAR BRAKE REMOVING THE REAR BRAKE Order Part name Q'ty Remarks Hold the machine by placing the suitable stand under the engine. Refer to "HANDLING NOTE". Rear wheel Refer to "FRONT WHEEL AND REAR WHEEL" section. Drain the brake fluid. Refer to removal section. 1 Brake pedal 1 2 Brake master cylinder 1 3 ...

  • Yamaha WR450F (2010) - page 176

    6-8 FRONT BRAKE AND REAR BRAKE DISASSEMBLING THE BRAKE CALIPER Order Part name Q'ty Remarks A. Front B. Rear AB 1P a d p i n 1 1 2 Brake pad 2 2 3 Pad support 1 1 4 Brake caliper piston 2 1 Re fer to removal section. 5 Brake caliper piston dust s eal 2 1 Refer to removal section. 6 Brake caliper piston seal 2 1 Refer to removal section. ...

  • Yamaha WR450F (2010) - page 177

    6-9 FRONT BRAKE AND REAR BRAKE DISASSEMBLING THE BRAKE MASTER CYLINDER Order Part name Q'ty Remarks A. Front B. Rear 1 Brake master cylinder cap 1 2 Diaphragm 1 3 Reserv oir floa t 1 4 Brake master cylinder boot 1 5 Circlip 1 Use a long nose circlip pliers. 6 Washer 1 7 Push rod 1 8 Brake master cylinder kit 1 ...

  • Yamaha WR450F (2010) - page 178

    6-10 FRONT BRAKE AND REAR BRAKE HANDLING NOTE Support the machine securely so there is no dange r of it falling over. DRAINING THE BRAKE FLUID 1. Remove: • Brake master cylinder cap "1" • Protector (rear brake) Do not remove the diaphragm. A. Front B. Rear 2. Connect the transparent hose " 2" to the bleed screw "1" ...

  • Yamaha WR450F (2010) - page 179

    6-11 FRONT BRAKE AND REAR BRAKE 3. Inspect: (front brake only) • Reservoir fl oat "1" Damage → Rep lace. 4. Inspect: • Brake master cylinder piston "1" • Brake master cylinder cup "2" Wear/damage/score marks → Re- place brake master cylinder kit. A. Front B. Rear CHECKING THE BRAKE CALIPER 1. Inspect: • Bra ...

  • Yamaha WR450F (2010) - page 180

    6-12 FRONT BRAKE AND REAR BRAKE 2. Install: • Brake caliper "1" • Bolt (brake caliper) "2" 3. Tighten: • Pad pin "3" 4. Install: • Pad pin plug "4" INSTALLING THE REAR BRAKE CALIPER 1. Install: • Pad support "1" • Brake pad "2" • Pad pin "3" • Install the b rake p ...

  • Yamaha WR450F (2010) - page 181

    6-13 FRONT BRAKE AND REAR BRAKE INSTALLING THE FRONT BRAKE MASTER CYLINDER 1. Install: • Brake master cylinder "1" • Brake master cylinder bracket "2" • Bolt (brake master cylinder b rack- et) "3" • Install the bracket so th at the arrow mark "a" face upward. • First tighten the bolts on the up per ...

  • Yamaha WR450F (2010) - page 182

    6-14 FRONT BRAKE AND REAR BRAKE 2. Install: • Brake hose holder "1" • Bolt (brake hos e holder) "2" 3. Install: • Brake hose holder "1" • Nut (brake hose holder) "2" Align the top "a" of the brake hose holder with the paint "b" of the brake hose. 4. Pass the brake hose through the ...

  • Yamaha WR450F (2010) - page 183

    6-15 FRONT BRAKE AND REAR BRAKE A. Front B. Rear 2. Air bleed: • Brake system Refer to "BLEEDING THE HY- DRAULIC BRAKE SYSTEM" sec- tion in the CHAPTER 3. 3. Inspect: • Brake fluid level Fluid at lower l evel → Fill up. Refer to "CHECKING THE BRAKE FLUID LEVEL" section in the CHAPTER 3. 4. Install: • Reservoir float (fro ...

  • Yamaha WR450F (2010) - page 184

    6-16 FRONT FORK FRONT FORK REMOVING THE FRONT FORK Order Part name Q'ty Remarks A. For CDN Hold the machine by placing the suitable stand under the engine. Refer to "HANDLING NOTE". Front wheel Refer to "FRONT WHEEL AND REAR WHEEL" section. Front brake caliper Refer to "FRONT BRAKE AND REAR BRAKE" section. Headlig ...

  • Yamaha WR450F (2010) - page 185

    6-17 FRONT FORK DISASSEMBLING THE F RONT FORK Order Part name Q'ty Remarks 1 Front fork cap bolt 1 Refer to removal section. 2 Fork spring 1 Drain the fork oil. 3 Dust seal 1 Refer to removal section. 4 Stopper ring 1 Refer to removal section. 5 Inner tube 1 Refer to removal section. 6 Outer tube 1 7 Piston metal 1 8 Slide metal 1 9 Oil seal w ...

  • Yamaha WR450F (2010) - page 186

    6-18 FRONT FORK HANDLING NOTE Support the machine securely so there is no dange r of it falling over. The front fork requires careful atten- tion. So it is recommended that the front fork be maintained at the deal- ers. To prevent an ac cidental explosion of air, the following instructions should be observed: • The front fork with a built-in pi s ...

  • Yamaha WR450F (2010) - page 187

    6-19 FRONT FORK The bending value is shown by one half of the dial gauge reading. Do not attempt to straighten a bent inner tube as this may dan gerous- ly weaken the tube . CHECKING THE OUTER TUBE 1. Inspect: • Outer tube "1 " Score marks/we ar/damage → Re- place. CHECKING THE FRONT FORK CAP BOLT 1. Inspect: • Front fork cap bolt & ...

  • Yamaha WR450F (2010) - page 188

    6-20 FRONT FORK 8. Install: • Outer tube "1 " To inner tube "2". 9. Install: • Slide me tal "1" • Oil seal washer "2" To outer tube slot. Press the slide metal into the outer tube with fork seal driver "3". 10. Insta ll: • Oil seal "1" Press the oil seal into the outer tube with fo ...

  • Yamaha WR450F (2010) - page 189

    6-21 FRONT FORK 20. Measure : • Oil level (left and right) "a" Out of specification → Adjust. Be sure to install the spring guide "2" when checking the oil level. Never fail to make the oil level ad- justment between the maximum and minimum level and always ad - just each front fork to the same setting. Uneven adjustmen t ca ...

  • Yamaha WR450F (2010) - page 190

    6-22 FRONT FORK INSTALLING T HE FRONT FORK 1. Install: • Front fork "1" • Temporarily tighte n the pinch bolts (lower brack et). • Do not tighten the pinch bolts (up- per bracket) yet. 2. Tighten: • Front fork cap bolt 3. Adjust: • Front fork top e nd "a" 4. Tighten: • Pinch bolt (upper bracket) "1" • Pin ...

  • Yamaha WR450F (2010) - page 191

    6-23 HANDLEBAR HANDLEBAR REMOVING THE HANDLEBAR Order Part name Q'ty Remarks Headlight 1 Hot starter cable 1 Disconnect at the lever side. 2 Hot start er lever hol der 1 3 Clutch cable 1 Disconnect at the lever side. 4 Clutch lever holder 1 Disconnect the clutch switch lead. 5 Engine stop switch 1 Disconnect the engine stop switch lead. 6 Brak ...

  • Yamaha WR450F (2010) - page 192

    6-24 HANDLEBAR REMOVING THE BRAKE MASTER CYLINDER 1. Remove: • Brake master cylinder bracket "1" • Brake master cylinder "2" • Do not let the brake master cylin- der hang on th e brake hose. • Keep the brake master cylinder cap side horizontal to prevent air from coming in. REMOVING THE GRIP 1. Remove: •G r i p " ...

  • Yamaha WR450F (2010) - page 193

    6-25 HANDLEBAR 5. Install: • Right grip "1" •C o l l a r " 2 " Apply the adhesive o n the tube guide "3". • Before applying the adhe sive, wipe off grease or oil on the tube guide surface "a" with a lacquer thinner. • Install the grip to t he tube gu ide so that the grip match mark "b" and t ...

  • Yamaha WR450F (2010) - page 194

    6-26 HANDLEBAR 12. Insta ll: • Clutch cable "1" • Hot starter cable "2" Apply the lithium soap base grease on the clutch cable end and hot start- er cable end. 13. Adjust: • Clutch lever free play Refer to "ADJUSTING THE CLUTCH CABLE FREE PLAY" section in the CHAPTER 3. • Hot starter lever free play Refer to &q ...

  • Yamaha WR450F (2010) - page 195

    6-27 STEERING STEERING REMOVING THE STEERING Order Part name Q'ty Remarks A. For CDN TIGHTENING STEPS: • Tighten ring nut. 38 Nm (3.8 m•kg , 27 ft•lb) • Loosen it one turn. • Retighten it. 7 Nm (0.7 m•kg, 5.1 ft•lb) Hold the machine by placing the suitable stand under the engine. Refer to "HANDLING NOTE". Headlight Hand ...

  • Yamaha WR450F (2010) - page 196

    6-28 STEERING 8 Lower bracket 1 9 Bearing race cover 1 10 Upper beari ng 1 11 Lower beari ng 1 Refer to removal section. 12 Bearing race 2 Refer to removal section. Order Part name Q'ty Remarks ...

  • Yamaha WR450F (2010) - page 197

    6-29 STEERING HANDLING NOTE Support the machine securely so there is no dange r of it falling over. REMOVING THE STEERING RING NUT 1. Remove: • Steering ring nut "1" Use the steering nut wrench "2". Support the steering st em so that it may not fall d own. REMOVING THE LOWER BEARING 1. Remove: • Lower bearin g "1" ...

  • Yamaha WR450F (2010) - page 198

    6-30 STEERING 6. Install: • Washer "1" 7. Install: • Front fork "1" • Upper bracket "2" • Main switch "3" • Front brake hose guide bracket "4" • Front reflector (For CDN) "5" • Nut (front reflector) (For CDN) "6" • Front reflecto r bracket (For CDN) "7" ...

  • Yamaha WR450F (2010) - page 199

    6-31 SWINGARM SWINGARM REMOVING THE SWINGARM Order Part name Q'ty Remarks Hold the machine by placing the suitable stand under the engine. Refer to "HANDLING NOTE". Brake hose holder Refer to "FRONT BRAKE AND REAR BRAKE" section. Rear brake caliper Refer to "FRONT BRAKE AND REAR BRAKE" section. Bolt (brake pedal) ...

  • Yamaha WR450F (2010) - page 200

    6-32 SWINGARM DISASSEMBLING THE SWINGARM Order Part name Q'ty Remarks 1 Cap 2 Refer to removal section. 2 Relay arm 1 3 Connecting rod 1 4 Collar 2 5 Oil seal 2 6 Thrust bearing 2 7 Bushing 2 8 Oil seal 8 9 Bearing 10 Refer to remova l section. ...

  • Yamaha WR450F (2010) - page 201

    6-33 SWINGARM HANDLING NOTE Support the machine securely so there is no dange r of it falling over. REMOVING THE CAP 1. Remove: • Left cap "1" Remove with a slotted-head screw- driver inserted under the mark " a" on the left cap. REMOVING THE BEARING 1. Remove: • Bearing "1" Remove the bearing by pressing its outer ...

  • Yamaha WR450F (2010) - page 202

    6-34 SWINGARM INSTALLING THE SWINGARM 1. Install: • Bushing "1" • Thrust bearing "2" • Oil seal "3" •C o l l a r " 4 " To swingarm "5" Apply the molybdenum disulfide grease on the bushin gs, thrust bear- ings, oil seal lips and contact surfaces of the collar and thrust b earing. 2. Install: ...

  • Yamaha WR450F (2010) - page 203

    6-35 SWINGARM 10. Tighten: • Nut (connectin g rod) "1" 11. Tighten: • Nut (relay arm) "1" 12. Insta ll: •C a p " 1 " Install the right cap with its mark "a" facing forward. 13. Insta ll: • Bolt (lower chain tensioner) "1" • Washer "2" •C o l l a r " 3 " • Lower chai ...

  • Yamaha WR450F (2010) - page 204

    6-36 REAR SHOCK ABSORBER REAR SHOCK ABSORBER REMOVING THE REAR SHOCK ABSORBER Order Part name Q'ty Remarks Hold the machine by placing the suitable stand under the engine. Refer to "HANDLING NOTE". Seat and side cover Refer to "REMOVING THE SEAT, FUEL TANK AND SIDE COVERS" section in the CHAPTER 3. Silencer Refer to "R ...

  • Yamaha WR450F (2010) - page 205

    6-37 REAR SHOCK ABSORBER 2 Taillight coupler 1 3 CDI unit coupler 3 4 Plastic band 1 5 Clamp (air filter joint) 1 Only loosening. 6R e a r f r a m e 1 7 Bolt (rear shock absorber-relay arm) 1 Hold the swingarm. 8 Bolt (rear shock absorber-frame) 1 9 Rear shock absorber 1 10 Lockn ut 1 Only loosening. 11 Adjuste r 1 Only loosening. 12 Lower spring g ...

  • Yamaha WR450F (2010) - page 206

    6-38 REAR SHOCK ABSORBER HANDLING NOTE • Support the machine securely so there is no danger of it falling over. • This rear shock absorber is pro- vided with a separate type tank filled with high- pressure nitro- gen gas. To pr event the danger of explosion, read and u nder- stand the follow ing information before handli ng the shock ab- sorber ...

  • Yamaha WR450F (2010) - page 207

    6-39 REAR SHOCK ABSORBER 2. Install: • Stopper ring (uppe r bearing) "1" After installing the sto pper ring, push back the bearing until it contacts the stopper ring. 3. Install: • Lower bearin g "1" Install the bearing by pressing it on the side having the manufacture' s marks or numbers. INSTALLING THE SPRING (REAR SH ...

  • Yamaha WR450F (2010) - page 208

    6-40 REAR SHOCK ABSORBER 7. Tighten: • Screw (air filter joint) "1" 8. Install: • Plastic band • Taillight coupler • Locking tie Screw (air filter joint): 3 Nm (0.3 m•kg, 2.2 ft•lb) ...

  • Yamaha WR450F (2010) - page 209

    7-1 ELECTRICAL COMPONENTS AND WIRING DIAGRAM ELECTRICAL This section is intended for those who have basi c knowled ge and skill concerning the servicing of Yamaha motorcycles (e.g., Yamaha dealers, se rvice engineers, etc.) Those who have little knowledge and ski ll concerning servicing are request- ed not to undertake inspection , adjustment, disa ...

  • Yamaha WR450F (2010) - page 210

    7-2 ELECTRICAL COMPONENTS AND WIRING DIAGRAM WIRING DIAGRAM 1. H eadlight 2. Mu lti-function display 3. En gine stop switch 4. C lutch switch 5. D iode 6. Starter relay dio de 7. T hrottle position sensor 8. Starter relay 9. F use 10. Starting circuit cut-off relay 11. CDI unit 12. Taillight 13. Neutral switch 14. Starter motor 15. AC magneto 16. R ...

  • Yamaha WR450F (2010) - page 211

    7-3 IGNITION SYSTEM IGNITION SYSTEM INSPECTION STEPS Use the following steps for checking the possibility of the malfuncti oning engine being attributable to igni tion system failure and for checking the spa rk plug which will no t spark. *1 marked: Refer to "CHECKING TH E FUSE" section in the CHAPTER 3. *2 marked: Refer to "CHECKING ...

  • Yamaha WR450F (2010) - page 212

    7-4 IGNITION SYSTEM SPARK GAP TEST 1. Disconnect the ignition coil from spark plug. 2. Remove the ignition co il cap. 3. Connect the dynamic spark tester "1" (ignition ch ecker "2") as shown. • Ignition coil "3" • Spark plug "4" A. For USA and CDN B. Except for USA and CDN 4. Kick the kickstarter crank. 5 ...

  • Yamaha WR450F (2010) - page 213

    7-5 ELECTRIC STARTING SYSTEM 3. Inspect: • Secondary coil resistance Out of specification → Replace. 4. Inspect: • Sealed portion of ignition coil "a" • Spark plug termin al pin "b" • Threaded porti on of spark plug "c" Wear → Replace. CHECKING THE AC MAGNETO 1. Inspect: • Pickup coil resistance Out of sp ...

  • Yamaha WR450F (2010) - page 214

    7-6 ELECTRIC STARTING SYSTEM INSPECTION STEPS If the starter motor will not operate, use the fo llowing inspection steps. *1 marked: Refer to "CHECKING TH E FUSE" section in the CHAPTER 3. *2 marked: Refer to "CHECKING AND CHARGIN G THE BATTERY" section in the CHAPTER 3. *3 marked: Refer to "CHECKING THE MAIN SWITCH" s ...

  • Yamaha WR450F (2010) - page 215

    7-7 ELECTRIC STARTING SYSTEM CHECKING THE COUPLERS AND LEADS CONNECTION 1. Check: • Couplers and lead s connection Rust/dust/looseness/short-circuit → Repair or replace. CHECKING THE STARTER MOTOR OPERATION 1. Connect the posi tive battery ter- minal "1" and starter motor lead "2" with a jumper lead "3". Not operat ...

  • Yamaha WR450F (2010) - page 216

    7-8 ELECTRIC STARTING SYSTEM CHECKING THE START SWITCH 1. Inspect: • Start switch conduction Not conductive while it is pushed → Replace. Conductive while it is freed → Re - place. Set the tester selection position to " Ω × 1". 2. Inspect: • Rubber part "a" Tears/damage → Replace. Tester (+) lead → Bla ck lead &quo ...

  • Yamaha WR450F (2010) - page 217

    7-9 ELECTRIC STARTING SYSTEM REMOVING THE STARTER MOTOR Order Part name Q'ty Remarks Exhaust pipe Refer to "REMOVING THE EXHAUST PIPE AND SILENCER" section in the CHAPTER 3. 1 Starter motor 1 ...

  • Yamaha WR450F (2010) - page 218

    7-10 ELECTRIC STARTING SYSTEM DISASSEMBLING THE STARTER MOTOR Order Part name Q'ty Remarks 1 Starter motor front cover 1 2 Washer (starter motor front cover) 1 3 Washer 1 4 Circlip 1 5O - r i n g 1 6 Starter motor yoke 1 7 Armature assembly 1 8 Starter motor rear cover 1 9 Brush 2 10 Brush spring 2 ...

  • Yamaha WR450F (2010) - page 219

    7-11 ELECTRIC STARTING SYSTEM CHECKING AND REPAIRING THE STARTER MOTOR 1. Check: • Commutator Dirt → Clean with 600 grit sandpa- per. 2. Measure: • Commutator diameter "a" Out of specification → Replace the starter motor. 3. Measure: • Mica undercut "a" Out of specification → Scrape the mica to the prope r measuremen ...

  • Yamaha WR450F (2010) - page 220

    7-12 ELECTRIC STARTING SYSTEM 4. Install: • O-ring "1" • Circlip • Plain washer "2" • Washer (starter motor front cover) "3" • Starter motor front cover "4" • For installatio n, align the projec- tions on the washer with the slots in the front cover. • Align the match mark "a" on the s ...

  • Yamaha WR450F (2010) - page 221

    7-13 CHARGING SYSTEM CHARGING SYSTEM INSPECTION STEPS If the battery is not charged, use the followin g inspection steps. *1 marked: Refer to "CHECKING TH E FUSE" section in the CHAPTER 3. *2 marked: Refer to "CHECKING AND CHARGIN G THE BATTERY" section in the CHAPTER 3. • Remove the follo wing parts before i nspection. 1. Sea ...

  • Yamaha WR450F (2010) - page 222

    7-14 CHARGING SYSTEM CHECKING THE COUPLERS AND LEADS CONNECTION 1. Check: • Couplers and lead s connection Rust/dust/looseness/short-circuit → Repair or replace. CHECKING THE CHARGING VOLTAGE 1. Start the engine. 2. Inspect: • Charging volt age Out of specification → If no failure is found in checking the source coil resistance, replace the ...

  • Yamaha WR450F (2010) - page 223

    7-15 THROTTLE POSITION SENSOR SYSTEM THROTTLE POSITION SENSOR SYSTEM INSPECTION STEPS If the throttle position senso r will not operate, use the follo wing inspection steps. Use the following special to ols in this inspection. Check entire ignition system for connection. No good → Repai r or replace. OK ↓ Check throttle position sen sor.(Thrott ...

  • Yamaha WR450F (2010) - page 224

    7-16 THROTTLE POSITION SENSOR SYSTEM HANDLING NOTE Do not loosen th e screw (throttle position sensor) "1" except when changing the th rottle position sen- sor due to failur e because it will cause a drop in engine pe rfor- mance. CHECKING THE COUPLERS AND LEADS CONNECTION 1. Check: • Couplers and lead s connection Rust/dust/looseness/s ...

  • Yamaha WR450F (2010) - page 225

    7-17 THROTTLE POSITION SENSOR SYSTEM 9. Adjust: • Throttle positi on sensor output voltage Adjustme nt steps: a. Adjust the installa tion angle of the throttle position sensor "1" to ob- tain the specified output voltage. Measure the output voltage accurate- ly with a digital e lectronic voltmeter that gives an easy reading of a small v ...

  • Yamaha WR450F (2010) - page 226

    7-18 LIGHTING SYSTEM LIGHTING SYSTEM INSPECTION STEPS Refer to th e following flow chart when inspect ing the lig hting system f or possible problems. • Remove the follo wing parts before i nspection. 1. Seat 2. Fuel tank 3. Left side cover • Use the follow ing special tools in this inspection. Check the bulb and bulb socket. No goo d → Repla ...

  • Yamaha WR450F (2010) - page 227

    7-19 LIGHTING SYSTEM CHECKING THE TAILLIGHT (LEDs) 1. Disconnect the taillight coupler. 2. Connect two jumper leads "1" from the battery terminals to the respective coupler terminal as shown. 3. Check: • LED (for proper operation) Does not light → Replace the tail- light assemb ly. • A wire that is used as a jumper lead must have at ...

  • Yamaha WR450F (2010) - page 228

    7-20 SIGNALING SYSTEM SIGNALING SYSTEM INSPECTION STEPS If the speedometer will not operate , use the following inspection steps. *1 marked: Refer to "CHECKING AND CHARGIN G THE BATTERY" section in the CHAPTER 3. • Remove the follo wing parts before i nspection. 1. Headlight • Use the follow ing special tools in this inspection. *1 Ch ...

  • Yamaha WR450F (2010) - page 229

    7-21 SIGNALING SYSTEM CHECKING THE COUPLERS AND LEADS CONNECTION 1. Check: • Couplers and lead s connection Rust/dust/looseness/short-circuit → Repair or replace. CHECKING THE MULTI-FUNCTION DISPLAY INPUT VOLTAGE 1. Disconn ect the multi- function dis- play coupler. 2. Set the main switch to "ON". 3. Measure: • Multi-function displa ...

Fabricant Yamaha Catégorie Motorcycle

Les documents que nous recevons du fabricant de l'appareilYamaha WR450F (2010) peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Yamaha
- manuels d’utilisations WR450F (2010)
- fiches produit Yamaha
- dépliants
- ou étiquettes-énergie Yamaha WR450F (2010)
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Yamaha WR450F (2010).

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Yamaha WR450F (2010), manuels d’entretien, brefs manuels ou manuels de l’utilisateur Yamaha WR450F (2010). Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Yamaha WR450F (2010).

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Yamaha WR450F (2010), quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Yamaha WR450F (2010) par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Yamaha WR450F (2010).

Le manuel d’utilisation complet Yamaha, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Yamaha WR450F (2010) - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Yamaha WR450F (2010), FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lYamaha WR450F (2010) qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Yamaha WR450F (2010) - qui devraient nous aider dans les premières étapes lors de l'utilisation Yamaha WR450F (2010)
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Yamaha WR450F (2010)
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Yamaha WR450F (2010) dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Yamaha WR450F (2010)?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Yamaha WR450F (2010), avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Yamaha WR450F (2010) il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)