Français dropdown-ico

Manuel d’utilisation Extron electronic ISS 506

184 pages 8.55 mb
Télécharger

Aller à la page of 184

Summary
  • Extron electronic ISS 506 - page 1

    ISS 506 Integration Seamless Switcher 68-1077-01 Rev . B 06 09 ...

  • Extron electronic ISS 506 - page 2

    This symbol is intended to alert the user of important operating and maintenance (servicing) instructions in the literature provided with the equipment. This symbol is intended to alert the user of the presence of uninsulated dangerous voltage within the product’ s enclosure that may present a risk of electric shock. Caution Read Instructions • ...

  • Extron electronic ISS 506 - page 3

    FCC Class A Notice This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interfer ence received, including interference that ma ...

  • Extron electronic ISS 506 - page 4

    ...

  • Extron electronic ISS 506 - page 5

    i ISS 506 Integration Seamless Switcher • T able of Contents T able of Contents Chapter One • Introduction ...................................................................................................... 1-1 About this Manual .................................................................................................................. ...

  • Extron electronic ISS 506 - page 6

    T able of Contents, cont’d ISS 506 Integration Seamless Switcher • T able of Contents ii Output Configuration menu............................................................................................. 3-11 Resolution and refresh rate submenu ........................................................................ 3-12 Output T ype subme ...

  • Extron electronic ISS 506 - page 7

    iii ISS 506 Integration Seamless Switcher • T able of Contents T oggling background illumination on and off ................................................................... 3-37 Using front panel security lockouts (executive modes) ..................................................... 3-38 Rear Panel Reset Button .............................. ...

  • Extron electronic ISS 506 - page 8

    T able of Contents, cont’d ISS 506 Integration Seamless Switcher • T able of Contents iv Using the Command/Response T ables ......................................................................... 4-11 Command/response table for SIS commands ......................................................... 4-12 Command/Response T able for IP SIS Comma ...

  • Extron electronic ISS 506 - page 9

    v ISS 506 Integration Seamless Switcher • T able of Contents Button Label Generator ....................................................................................................... 5-27 Using the Button Label Generator software ...................................................................... 5-27 Special Characters .................. ...

  • Extron electronic ISS 506 - page 10

    T able of Contents, cont’d ISS 506 Integration Seamless Switcher • T able of Contents vi Chapter 7 • Modifications ........................................................................................................... 7-1 Opening the Switcher ............................................................................................... ...

  • Extron electronic ISS 506 - page 11

    ISS 506 Integration Seamless Switcher 1 Chapter One Intr oduction About this Manual About the Integration Seamless Switchers Features ...

  • Extron electronic ISS 506 - page 12

    ISS 506 Integration Seamless Switcher • Introduction 1-2 Intr oduction About this Manual This manual contains installation, configuration, and operating information for the Extron ISS 506 family of 6-input Integration Seamless Switchers with audio. About the Integration Seamless Switchers The Extron ISS 506 is a family of scaling, video and ster ...

  • Extron electronic ISS 506 - page 13

    1-3 ISS 506 Integration Seamless Switcher • Introduction 10 0-240V 50/60 H z 2A M AX R / R -Y SDI G /Y V ID S B /C B -Y H H V /V V H /H V R S23 2/422 1 L R R / R -Y 1 2 G /Y V ID B /C B -Y R / R -Y G /Y V ID B /C B -Y H V /V V H /H V V R / R -Y 3 4 G /Y V ID B /C B -Y V ID /Y R -Y VID B -Y /C V G /Y 5 R R-Y LAN RESET O U T P U T S 6 YC B / B -Y P ...

  • Extron electronic ISS 506 - page 14

    Intr oduction, cont’d ISS 506 Integration Seamless Switcher • Introduction 1-4 The ISS receives and outputs the ster eo audio on 5-pole captive screw connectors. The audio can be switched with cross fading (that is, the pr evious audio channel fades out and then the new audio channel fades in). For upscaling, the ISS 506 converts the horizontal ...

  • Extron electronic ISS 506 - page 15

    1-5 ISS 506 Integration Seamless Switcher • Introduction Audio outputs — The ISS outputs the selected unamplified, line level, balanced or unbalanced stereo or mono audio on 5-pole captive scr ew connectors. Operational flexibility — Operations such as input selection, transitions, and picture adjustments, and volume contr ol can be perform ...

  • Extron electronic ISS 506 - page 16

    Intr oduction, cont’d ISS 506 Integration Seamless Switcher • Introduction 1-6 T ransitions — Control the type of switch that occurs between the pr eview and program outputs. The Cut button cr eates an instant switch between the preview and pr ogram outputs. The W ipe and Dissolve buttons switch with a masking effect. T est patterns — The s ...

  • Extron electronic ISS 506 - page 17

    ISS 506 Integration Seamless Switcher 2 Chapter T wo Installation Mounting the Switcher Cabling and Rear Panel Views Front Panel Configuration Port Configuration ...

  • Extron electronic ISS 506 - page 18

    ISS 506 Integration Seamless Switcher • Installation 2-2 Installation Mounting the Switcher Four uninstalled rubber feet are included with the seamless switcher . If you are going to rack mount the switcher , mount it before you cable it (see “Rack mounting”, below), and do not install the rubber feet. If you are not rack mounting the seamles ...

  • Extron electronic ISS 506 - page 19

    2-3 ISS 506 Integration Seamless Switcher • Installation Mounting instructions For optional rack mounting, do not install the rubber feet. Mount the ISS 506 in a rack as follows: 1 . Attach the included MBD 249 rack/through-desk mounting brackets to the unit, using eight machine screws supplied with the mounting kit (figur e 2-1). Use the lower ...

  • Extron electronic ISS 506 - page 20

    Installation, cont’d ISS 506 Integration Seamless Switcher • Installation 2-4 Cabling and Rear Panel V iews All connectors are on the r ear panel (figure 2-2). 100-240V 50/60 Hz 2A MAX R/ R-Y SDI G/Y VID S B/C B-Y H H/HV V H/HV RS232/422 1 L R R/ R-Y 1 2 G/Y VID B/C B-Y R/ R-Y G/Y VID B/C B-Y H/HV V H/HV V V R/ R-Y 3 4 G/Y VID B/C B-Y VID /Y R ...

  • Extron electronic ISS 506 - page 21

    2-5 ISS 506 Integration Seamless Switcher • Installation d Input 6 video connectors — Connect either an S-video, a composite video, or an SDI/HD-SDI video source to these connectors (figur e 2-5). VID 6 YC SDI VID 6 YC VID 6 YC SDI Composite Video SDI or HD-SDI Video (Optional SDI/HDSDI Input Board Onl y ) S-Video SDI Figure 2-5 — Connection ...

  • Extron electronic ISS 506 - page 22

    Installation, cont’d ISS 506 Integration Seamless Switcher • Installation 2-6 Output connections Video output connections N The two Program V ideo outputs, consisting of one set of five BNC connectors and a 15-pin HD connector , output identical video signals at the same resolution, r efresh rate, and sync format. The Program connectors ( f an ...

  • Extron electronic ISS 506 - page 23

    2-7 ISS 506 Integration Seamless Switcher • Installation 9a DVI output connector (optional) — If the optional DVI output board (figure 2-9) is installed, connect a DVI/HDMI-compatible video display to this DVI connector . This connector outputs the program image only . For an HDMI-compatible display , connect the display through a DVI-to-HDMI ...

  • Extron electronic ISS 506 - page 24

    Installation, cont’d ISS 506 Integration Seamless Switcher • Installation 2-8 Audio output connections j Preview and Program audio output connectors — Connect audio devices, such as an audio amplifier or powered speakers, to these 3.5 mm, 5-pole captive screw connectors. The connectors output the selected unamplified, line level audio. See ...

  • Extron electronic ISS 506 - page 25

    2-9 ISS 506 Integration Seamless Switcher • Installation Choosing a network cable Ethernet links use Category (CA T) 3, 4, 5, 5e, or 6, unshielded twisted pair (UTP) or shielded twisted pair (STP) cables, terminated with RJ-45 connectors. Ethernet cables are limited to 328' (100 m). N Do not use standard telephone cables. T elephone cables d ...

  • Extron electronic ISS 506 - page 26

    Installation, cont’d ISS 506 Integration Seamless Switcher • Installation 2-10 Serial port connection l RS-232/422 port — Connect a host device, such as a computer or touch panel control, to the ISS 506 Integration Seamless Switcher via this 9-pin D connector for serial RS-232 or RS-422 control (figur e 2-14). RS-232 Function Pin Function 1 ...

  • Extron electronic ISS 506 - page 27

    2-11 ISS 506 Integration Seamless Switcher • Installation Fr ont Panel Configuration Port TRANSITION PICTURE ADJUSTMENTS CONFIG ZOOM T AKE PIP TITLE SIZE DET AIL POSITION BRIGHT/ CONT COLOR/ TINT ISS 506 Integration Seamless Switcher VO LUME ADJUST ADJUST MENU NEXT 14 Figure 2-15 — Fr ont panel configuration port n Configuration port — Thi ...

  • Extron electronic ISS 506 - page 28

    Installation, cont’d ISS 506 Integration Seamless Switcher • Installation 2-12 Configuration The ISS can be configured using either the fr ont panel controls, the SIS, the HTML pages, or the W indows-based Control program. See chapter 3, “Operation”; chapter 4, “SIS Programming and Contr ol”; chapter 5, “Scaler Software”, and chap ...

  • Extron electronic ISS 506 - page 29

    ISS 506 Integration Seamless Switcher 3 Chapter Thr ee Operation Front Panel Controls and Indicators Front Panel Operations Rear Panel Reset Button Optimizing the Video Optimizing the Audio T roubleshooting ...

  • Extron electronic ISS 506 - page 30

    ISS 506 Integration Seamless Switcher • Operation 3-2 Operation Fr ont Panel Controls and Indicators All of the switcher ’s contr ols and indicators, with the exception of the Reset button, are on the fr ont panel (figure 3-1). The buttons can be set to pr ovide amber background illumination all the time or the backgr ound illumination can be ...

  • Extron electronic ISS 506 - page 31

    3-3 ISS 506 Integration Seamless Switcher • Operation e T ake button — Pressing the T ake button causes the ISS to switch the input that was selected as the preview output with the pr ogram output, using the effect that was selected by the lit Ef fect button ( f ). The T ake button blinks for the duration of the switching effect. For the PIP an ...

  • Extron electronic ISS 506 - page 32

    Operation, cont’d ISS 506 Integration Seamless Switcher • Operation 3-4 h Status display — The 16-column by 2-line LCD window displays configuration menus and status information. See “Menu system overview”, below , and “Front Panel Operations”, later in this chapter , for details. i Menu button — The Menu button enters and moves th ...

  • Extron electronic ISS 506 - page 33

    3-5 ISS 506 Integration Seamless Switcher • Operation Default Cycle Menu 2 sec. Po wer on Men u Next Men u Men u Men u * This me nu is av ailable only if the optional scan con ve r ter board is installed. Men u Men u Men u 30 sec. 30 sec. 30 sec. Input Configuratio n Output Configuratio n Au to Imag e Integration SeamlessSwitche r Men u Men u 30 ...

  • Extron electronic ISS 506 - page 34

    Operation, cont’d ISS 506 Integration Seamless Switcher • Operation 3-6 Auto Image menu Figure 3-3 shows an overview of the Auto Image menu, the Select output submenu, and the available settings. • Program • Previe w • Both Default Cycle Menu Menu 30 sec. 30 sec. Men u Menu Next Next Next Menu Menu Menu Menu Menu Menu Menu Menu Au to Imag ...

  • Extron electronic ISS 506 - page 35

    3-7 ISS 506 Integration Seamless Switcher • Operation Default Cycle Menu Menu Men u Menu Next Menu Menu Menu Menu Menu Menu Menu Input Configuratio n Au to Image Output Configuratio n Effect s Configuratio n Logo Capture User Preset s Ad va nced Configuratio n View Comm Setting s Scan Con verter Configuratio n Exit Menu Press Next * 30 sec. 30 se ...

  • Extron electronic ISS 506 - page 36

    Operation, cont’d ISS 506 Integration Seamless Switcher • Operation 3-8 Audio Level submenu Rotate the Adjust [ knob while the Input format submenu is active to select an input to configure. Rotate the Adjust { knob to select the audio gain or attenuation value, from -18 dB to +24 dB. The default for each input is a 0 dB audio level. Film Mode ...

  • Extron electronic ISS 506 - page 37

    3-9 ISS 506 Integration Seamless Switcher • Operation This early scaling results in a blank border on the left side and cr opping on the right side, and looks as if the image is shifted to the right. Similarly , if the vertical start adjustment is set to less than the amount of actual blanking, the ISS starts scaling before the first line of the ...

  • Extron electronic ISS 506 - page 38

    Operation, cont’d ISS 506 Integration Seamless Switcher • Operation 3-10 These lines appear as fuzzy vertical bars when an alternating pixels pattern is applied. When the total pixels setting is improperly adjusted, the entir e image can have a noisy or darkened appearance. Adjusting the phase corrects this. As an approximate setting, multiply ...

  • Extron electronic ISS 506 - page 39

    3-11 ISS 506 Integration Seamless Switcher • Operation Adjust the Active Pixels variable to increase and decr ease the number of active pixels, shifting the starting period horizontally on the screen. Adjust the Active Lines variable to increase and decr ease the number of lines. N Figure 3-7 shows an image whose active ar ea is improperly set, a ...

  • Extron electronic ISS 506 - page 40

    Operation, cont’d ISS 506 Integration Seamless Switcher • Operation 3-12 Resolution and refr esh rate submenu Rotate the Adjust [ knob while this submenu is active to select one of the available output resolutions. See the table below . Rotate the Adjust { knob while this submenu is active to select one of the available refr esh (verti cal sc a ...

  • Extron electronic ISS 506 - page 41

    3-13 ISS 506 Integration Seamless Switcher • Operation Output T ype submenu Rotate either Adjust knob while this submenu is active to select the output video type (RGBHV , RGsB, component [YUV] with tri-level sync, or component [YUV] with bi-level sync). Sync Polarity submenu The display or projector may r equire a particular combination of horiz ...

  • Extron electronic ISS 506 - page 42

    Operation, cont’d ISS 506 Integration Seamless Switcher • Operation 3-14 Dissolve Conguration submenu The Dissolve Duration submenu displays and allows you to set the duration of the dissolve effect that is applied when you ar e switching the preview output to the program output or switching among pictur e-in-picture window inputs. Use eithe ...

  • Extron electronic ISS 506 - page 43

    3-15 ISS 506 Integration Seamless Switcher • Operation WIPE RIGHT SOFT WIPE LEFT SOFT WIPE UP SOFT WIPE DOWN SOFT WIPE CENTER IN SOFT WIPE CENTER OUT SOFT WIPE CURT AIN IN SOFT WIPE CURT AIN OUT SOFT WIPE SQUARE IN SOFT WIPE SQUARE OUT SOFT WIPE PLUS IN SOFT WIPE PLUS OUT SOFT WIPE RIGHT HARD WIPE LEFT HARD WIPE UP HARD WIPE DOWN HARD WIPE CENTER ...

  • Extron electronic ISS 506 - page 44

    Operation, cont’d ISS 506 Integration Seamless Switcher • Operation 3-16 Logo Capture menu Figure 3-1 1 is a flowchart that shows an overview of the Logo Capture menu, the submenus, and the available settings. See “Capturing a logo” on page 3-30 for more details on using this menu. 30 sec. 30 sec. 30 sec. 30 sec. Next * Next Next Ne xt Nex ...

  • Extron electronic ISS 506 - page 45

    3-17 ISS 506 Integration Seamless Switcher • Operation Capture Start submenu The Capture Start submenu displays and allows you to set the starting point of the logo to be captured. Use this submenu, along with the Captur e Size submenu to define the area to be saved as a logo. Rotate the Adjust [ knob while this submenu is active to position a l ...

  • Extron electronic ISS 506 - page 46

    Operation, cont’d ISS 506 Integration Seamless Switcher • Operation 3-18 User Presets menu Figure 3-12 is a flowchart that shows an overview of the User Pr esets menu, the Save User Preset and Erase User Pr eset submenus, and the available settings. 30 sec. 30 sec. 30 sec. Next * Next Ne xt Men u Default Cycle Menu Menu Men u Menu Next Menu Me ...

  • Extron electronic ISS 506 - page 47

    3-19 ISS 506 Integration Seamless Switcher • Operation N The User Preset is tailor ed for the selected output rate. If you change the output rate and then recall a pr eset for the earlier rate, the adjustments recalled in the preset have no effect on the video output. However , if you then change back to the earlier output rate, the effects of th ...

  • Extron electronic ISS 506 - page 48

    Operation, cont’d ISS 506 Integration Seamless Switcher • Operation 3-20 Auto Image submenu The Auto Image submenu provides a means to turn the auto imaging on or of f for individual input selections. If auto imaging is set to on, the ISS always sizes and centers the selected input to fill the screen when a new fr equency is input. If auto ima ...

  • Extron electronic ISS 506 - page 49

    3-21 ISS 506 Integration Seamless Switcher • Operation Split Color Bars (8) Crosshatch Crosshatch 4x4 Split Grayscale Ramp Alt Pixels Crop 1.78 Aspect Ratio 1.33 Aspect Ratio 1.85 Aspect Ratio 2.35 Aspect Ratio Figure 3-14 — T est patterns Blue Mode submenu The Blue Mode submenu lets you turn the blue-only mode feature on and of f. Blue- only m ...

  • Extron electronic ISS 506 - page 50

    Operation, cont’d ISS 506 Integration Seamless Switcher • Operation 3-22 Preview Switch Mode submenu The Preview Switch Mode submenu lets you set the way the pr eview output responds to the cut or take operation.  • Stay mode — For either a cut or take operation, the video and audio signals on the preview output ar e applied to the pr ...

  • Extron electronic ISS 506 - page 51

    3-23 ISS 506 Integration Seamless Switcher • Operation View and Edit Communications Settings menu Figure 3-16 is a flowchart that shows an overview of both the V iew User Communications Settings and the Edit User Communications Settings menus, the submenus, and the available settings. Menu 30 sec. 30 sec. 30 sec. 30 sec. 30 sec. 30 sec. Edit Set ...

  • Extron electronic ISS 506 - page 52

    Operation, cont’d ISS 506 Integration Seamless Switcher • Operation 3-24 MAC Address display The read-only MAC Address display shows the hardcoded, factory assigned hardwar e address. DHCP Mode submenu The DHCP Mode submenu displays the on or of f status of the Dynamic Host Configuration Protocol (DHCP) method of IP addressing. If DHCP is on, ...

  • Extron electronic ISS 506 - page 53

    3-25 ISS 506 Integration Seamless Switcher • Operation Scan Converter Configuration menu Figure 3-17 is a flowchart that shows an overview of the Scan Converter Configuration menu, the submenus, and the available settings. The Scan Converter Configuration menu is displayed only if an optional scan converter output board is installed. N If no ...

  • Extron electronic ISS 506 - page 54

    Operation, cont’d ISS 506 Integration Seamless Switcher • Operation 3-26 Output Format submenu The Output Format submenu displays and allows you to change the format of the scan converted output. When this submenu is active, rotate either Adjust knob to select among RGsB, low resolution component video (YUV), or composite video and S-video. N T ...

  • Extron electronic ISS 506 - page 55

    3-27 ISS 506 Integration Seamless Switcher • Operation Exit menu From the Exit menu (figur e 3-18), press the Next button to r eturn to the default display cycle, or press the Menu button to r eturn to the Auto Image menu. 30 sec. Menu Menu Default Cycle Next * Men u Menu Menu Menu Menu Menu Menu Menu Menu Menu Exit Menu Press Next Input Configu ...

  • Extron electronic ISS 506 - page 56

    Operation, cont’d ISS 506 Integration Seamless Switcher • Operation 3-28 The selected preview and pr ogram inputs, the picture adjustments, and other current settings ar e saved in nonvolatile memory . When power is applied, the latest configuration is retrieved. N The ISS requir es some time to save any new settings. Wait at least 5 minutes b ...

  • Extron electronic ISS 506 - page 57

    3-29 ISS 506 Integration Seamless Switcher • Operation Selecting an input to be the preview output and switching it to the program output N In this example, the switcher is set to Swap mode. See “Preview Switch Mode submenu”, earlier in this chapter . 1 . Press and r elease a preview input button (figur e 3-20). PROGRAM PREVIEW LOGO 2 /BLACK ...

  • Extron electronic ISS 506 - page 58

    Operation, cont’d ISS 506 Integration Seamless Switcher • Operation 3-30 T ake button — The ISS switches the input selected as the preview output to the program output using the ef fect selected by one of the Effect buttons (figure 3-22). TRANSITION EFFECTS T AKE CUT T AKE PIP TITLE WIPE DISSOL VE PREVIEW 1 2 3 4 5 6 LOGO 2 /BLACK LOGO 1 /BL ...

  • Extron electronic ISS 506 - page 59

    3-31 ISS 506 Integration Seamless Switcher • Operation Capturing a logo The ISS can capture an on-scr een image to use as a logo. N A logo is a bitmap image that can be superimposed on top of the preview and/or program output. Capture a displayed image as a logo as follows: 1 . Press the Menu button until the LCD window displays the Logo Captur e ...

  • Extron electronic ISS 506 - page 60

    Operation, cont’d ISS 506 Integration Seamless Switcher • Operation 3-32 6 . Press the Next button (figur e 3-25). The Capture Size submenu appears. Default Cycle Press NEXT Step 6 Press NEXT Step 8 Press NEXT Step 10 Step 11 Rotate the knobs to mo ve the lo wer-r ight corner of the image area to be captured. Step 9 Step 7 30 sec. 0000 through ...

  • Extron electronic ISS 506 - page 61

    3-33 ISS 506 Integration Seamless Switcher • Operation Configuring a logo Once a bitmap is captured or uploaded via the LAN port, you can assign it to one of the two logo locations. After it is assigned, you can position it and remove (key out) unwanted portions of the image (such as backgrounds). Assign the bitmap to a logo and configure the l ...

  • Extron electronic ISS 506 - page 62

    Operation, cont’d ISS 506 Integration Seamless Switcher • Operation 3-34 6 . Rotate the Adjust { knob to select (< >) how you will remove (key out) unwanted portions of the bitmap. Level — The ISS keys out all material whose luminance level is below a variable threshold. RGB — The ISS keys out all material of a specific color (red, g ...

  • Extron electronic ISS 506 - page 63

    3-35 ISS 506 Integration Seamless Switcher • Operation Configuring a title The ISS can display the input that is selected to be the preview output as a title. N A title is preview output superimposed over the pr ogram output. Remove (key out) unwanted portions of the title (such as backgrounds) as follows: 1 . Ensure that the video that you want ...

  • Extron electronic ISS 506 - page 64

    Operation, cont’d ISS 506 Integration Seamless Switcher • Operation 3-36 Adjusting the picture The picture adjustments allow you to fine tune the image quality of the selected input. When you press one of the Pictur e Adjustment buttons (Color/T int, Brightness/Contrast, Size, Position, or Detail) once, the corresponding image adjustment menu ...

  • Extron electronic ISS 506 - page 65

    3-37 ISS 506 Integration Seamless Switcher • Operation Adjust an image as follows (figure 3-29). 1. Press the desir ed input button to select the input to adjust. N The adjustments are made to the input signal that is switched to the output (preview or pr ogram) shown in the LCD window . N Color adjustments are available only for component video ...

  • Extron electronic ISS 506 - page 66

    Operation, cont’d ISS 506 Integration Seamless Switcher • Operation 3-38 Using front panel security lockouts (executive modes) There ar e four levels of front panel security lockout that limit the various aspects of the operation of the ISS 506 Integration Seamless Switcher from the fr ont panel.  • Complete — All front panel function ...

  • Extron electronic ISS 506 - page 67

    3-39 ISS 506 Integration Seamless Switcher • Operation Rear Panel Reset Button The switcher ’s Reset button is on the r ear panel (figure 3-32). RS232/422 RESET B/ B-Y PREVIEW RGB/R- Y, Y, B-Y RGB/R- Y, Y, B-Y R PREVIEW LAN 12 Figure 3-32 — ISS 506 r ear panel Reset button l Reset button and LED — Use the Reset button and LED to perform fo ...

  • Extron electronic ISS 506 - page 68

    Operation, cont’d ISS 506 Integration Seamless Switcher • Operation 3-40 Perform a soft reset of the switcher as follows: 1 . Use an Extron tweeker or other small scr ewdriver to press and hold the Reset button until the Reset LED blinks once (for events reset), twice (for IP settings), or three times (for absolute r eset) (figure 3-33). 2 . R ...

  • Extron electronic ISS 506 - page 69

    3-41 ISS 506 Integration Seamless Switcher • Operation Performing a hard r eset The hard r eset function restor es the switcher to the base firmware that it was shipped with. After a hard reset, events do not automatically start, but user settings and files are r estored. Perform a har d reset as follows: N The hard reset r estores the factory- ...

  • Extron electronic ISS 506 - page 70

    Operation, cont’d ISS 506 Integration Seamless Switcher • Operation 3-42 3 . Select an input. Use the ISS’s size and center functions to adust the crop or aspect ratio output to fill the screen. N If the input source is a DVD, set the DVD player to output a 16:9 aspect ratio before sizing the image using the ISS’ s size function to correct ...

  • Extron electronic ISS 506 - page 71

    3-43 ISS 506 Integration Seamless Switcher • Operation T roubleshooting The following tips may help you in troubleshooting. • Somesymptomsmayresembleothers,soyoumaywanttolookthr oughall of the examples before attempting to solve the pr oblem. • Beprepar edtobacktrackincasetheac ...

  • Extron electronic ISS 506 - page 72

    Operation, cont’d ISS 506 Integration Seamless Switcher • Operation 3-44 Specific problems The table below shows some common operating problems and their solutions. Problem Cause Solution No image appears. The input signal is Connect an input device that is incompatible. compatible with the ISS. The input is impr operly Use the Input Format su ...

  • Extron electronic ISS 506 - page 73

    ISS 506 Integration Seamless Switcher 4 Chapter Four SIS Pr ogramming and Control Serial Links Ethernet Link Symbols Switcher-Initiated Messages Host-to-Switcher Instructions Switcher Error Responses Using the Command/Response T ables Command/Response T able for SIS Commands Command Response T able for IP SIS Commands Special Characters ...

  • Extron electronic ISS 506 - page 74

    ISS 506 Integration Seamless Switcher • SIS Programming and Contr ol 4-2 SIS Pr ogramming and Contr ol Serial Links The switcher has two serial ports that can be connected to a host device such as a computer running the HyperT erminal utility , an RS-232 capable PDA, or a control system. These ports make serial control of the switcher possible. T ...

  • Extron electronic ISS 506 - page 75

    4-3 ISS 506 Integration Seamless Switcher • SIS Programming and Contr ol Front panel Configuration port N This port is hardwired for RS-232 only . N This port is independent of the rear panel RS-232/RS-422 port. A front panel Configuration port connection and a rear panel RS-232/RS-422 port connection can both be active at the same time. The op ...

  • Extron electronic ISS 506 - page 76

    SIS Pr ogramming and Control, cont’d ISS 506 Integration Seamless Switcher • SIS Programming and Contr ol 4-4 Ether net Link The rear panel Ethernet connector on the switcher (figur e 4-3) can be connected to an Ethernet LAN or W AN. This connection makes SIS control of the switcher possible using a computer connected to the same LAN or W AN. ...

  • Extron electronic ISS 506 - page 77

    4-5 ISS 506 Integration Seamless Switcher • SIS Programming and Contr ol Symbols Symbols ( X / values), defined below , are used throughout the discussions of the switcher-initiated messages that begin on the next page and the command/ response table that begins on page 4-12. The symbols r epresent variables in the switcher-initiated messages an ...

  • Extron electronic ISS 506 - page 78

    SIS Pr ogramming and Control, cont’d ISS 506 Integration Seamless Switcher • SIS Programming and Contr ol 4-6 X4$ = Frequency: nnn . nn (kHz [horizontal] or Hz [vertical]) X4% = Lockout mode: 0 = Unlocked 1 = Program lock — Lock Program buttons 2 = Switch free lock — Lock Picture Adjustments, menu controls, and effect selection 3 = V olume ...

  • Extron electronic ISS 506 - page 79

    4-7 ISS 506 Integration Seamless Switcher • SIS Programming and Contr ol Title Eff3* X^ * nnn * 1 * X& ] The operator has pressed the Ef fect T itle button on the front panel. Eff3 indicates “title”. X^ is the key threshold. “ nnn ” has no meaning in this r esponse. The “1” after nnn indicates that this effect is selected. X& ...

  • Extron electronic ISS 506 - page 80

    SIS Pr ogramming and Control, cont’d ISS 506 Integration Seamless Switcher • SIS Programming and Contr ol 4-8 Cutting or dissolving in swap mode The switcher issues the following reports when you swap the pr eview and program outputs in stay mode: Tke1* X* ] The switcher has received the fr ont panel T ake command. Bsy1 ] The switcher is perfor ...

  • Extron electronic ISS 506 - page 81

    4-9 ISS 506 Integration Seamless Switcher • SIS Programming and Contr ol Picture adjustments X@ Col X2& ] A front panel color adjustment has occurred. X@ is the output (pr ogram or preview) switched to the adjusted input and X2& is the color variable. X@ T in X2& ] A front panel tint adjustment has occurred. X@ is the output (pr ogram ...

  • Extron electronic ISS 506 - page 82

    SIS Pr ogramming and Control, cont’d ISS 506 Integration Seamless Switcher • SIS Programming and Contr ol 4-10 RGB delay Dly X# ] A front panel RGB delay adjustment has occurred. RGB delay affects input selections for the preview output only . X# is the delay value, in 0.1 second steps. X# can be as much as 50 = 5.0 seconds. T est pattern Ts t ...

  • Extron electronic ISS 506 - page 83

    4-11 ISS 506 Integration Seamless Switcher • SIS Programming and Contr ol Host-to-Switcher Instructions The switcher accepts SIS commands through its serial ports and/or its LAN port. SIS commands consist of one or more characters per command field. They do not requir e any special characters to begin or end the command character sequence. Each ...

  • Extron electronic ISS 506 - page 84

    SIS Pr ogramming and Control, cont’d ISS 506 Integration Seamless Switcher • SIS Programming and Contr ol 4-12 Command ASCII (T elnet) (host to switcher) URL Encoded (Web) (host to switcher) Response (switcher to host) Additional description Input selection Select video and audio X@ * X! ! X@ * X! ! Out X@ •In X! •All ] Select video and aud ...

  • Extron electronic ISS 506 - page 85

    4-13 ISS 506 Integration Seamless Switcher • SIS Programming and Contr ol Command/response table for SIS commands (continued) Command/response table for SIS commands (continued) Command ASCII (T elnet) (host to switcher) URL Encoded (Web) (host to switcher) Response (switcher to host) Additional description Wipe effect, duration, and subef fect N ...

  • Extron electronic ISS 506 - page 86

    SIS Pr ogramming and Control, cont’d ISS 506 Integration Seamless Switcher • SIS Programming and Contr ol 4-14 Command/response table for SIS commands (continued) Command ASCII (T elnet) (host to switcher) URL Encoded (Web) (host to switcher) Response (switcher to host) Additional description PIP effect configuration Set the PIP ef fect 4*4*# ...

  • Extron electronic ISS 506 - page 87

    4-15 ISS 506 Integration Seamless Switcher • SIS Programming and Contr ol Command/response table for SIS commands (continued) Command ASCII (T elnet) (host to switcher) URL Encoded (Web) (host to switcher) Response (switcher to host) Additional description Preview switch mode Set preview switch “stay” mode 20*1# 20*1# Psm1 ] Set pr eview moni ...

  • Extron electronic ISS 506 - page 88

    SIS Pr ogramming and Control, cont’d ISS 506 Integration Seamless Switcher • SIS Programming and Contr ol 4-16 Command/response table for SIS commands (continued) Command ASCII (T elnet) (host to switcher) URL Encoded (Web) (host to switcher) Response (switcher to host) Additional description View selected input V iew selected video and audio i ...

  • Extron electronic ISS 506 - page 89

    4-17 ISS 506 Integration Seamless Switcher • SIS Programming and Contr ol Command/response table for SIS commands (continued) Command ASCII (T elnet) (host to switcher) URL Encoded (Web) (host to switcher) Response (switcher to host) Additional description Video mute V ideo mute on X@ *1B X@ *1B X@ Vmt1 ] Set the X@ video output to black. The but ...

  • Extron electronic ISS 506 - page 90

    SIS Pr ogramming and Control, cont’d ISS 506 Integration Seamless Switcher • SIS Programming and Contr ol 4-18 Command/response table for SIS commands (continued) Command ASCII (T elnet) (host to switcher) URL Encoded (Web) (host to switcher) Response (switcher to host) Additional description V ertical shift Set a specific vertical position X@ ...

  • Extron electronic ISS 506 - page 91

    4-19 ISS 506 Integration Seamless Switcher • SIS Programming and Contr ol Command/response table for SIS commands (continued) Command ASCII (T elnet) (host to switcher) URL Encoded (Web) (host to switcher) Response (switcher to host) Additional description Pixel phase N The pixel phase adjustment is available only for RGB, YUV -HD, and YUVp input ...

  • Extron electronic ISS 506 - page 92

    SIS Pr ogramming and Control, cont’d ISS 506 Integration Seamless Switcher • SIS Programming and Contr ol 4-20 Command/response table for SIS commands (continued) Command ASCII (T elnet) (host to switcher) URL Encoded (Web) (host to switcher) Response (switcher to host) Additional description Film mode (P AL 2:2 pulldown) N The film mode selec ...

  • Extron electronic ISS 506 - page 93

    4-21 ISS 506 Integration Seamless Switcher • SIS Programming and Contr ol Command/response table for SIS commands (continued) Command ASCII (T elnet) (host to switcher) URL Encoded (Web) (host to switcher) Response (switcher to host) Additional description Auto Image Enable Auto Image 55* X! *1# 55* X! *1# Img X! *1 ] Auto Image input X! when sel ...

  • Extron electronic ISS 506 - page 94

    SIS Pr ogramming and Control, cont’d ISS 506 Integration Seamless Switcher • SIS Programming and Contr ol 4-22 Command/response table for SIS commands (continued) Command ASCII (T elnet) (host to switcher) URL Encoded (Web) (host to switcher) Response (switcher to host) Additional description Contrast Set a specific contrast value X@ * X2& ...

  • Extron electronic ISS 506 - page 95

    4-23 ISS 506 Integration Seamless Switcher • SIS Programming and Contr ol Command ASCII (T elnet) (host to switcher) URL Encoded (Web) (host to switcher) Response (switcher to host) Additional description Blue screen T urn blue screen mode on 8*1# 8*1# Blu1 ] Output sync and blue video only on both outputs. T urn blue screen mode of f 8*0# 8*0# B ...

  • Extron electronic ISS 506 - page 96

    SIS Pr ogramming and Control, cont’d ISS 506 Integration Seamless Switcher • SIS Programming and Contr ol 4-24 Command/response table for SIS commands (continued) Command ASCII (T elnet) (host to switcher) URL Encoded (Web) (host to switcher) Response (switcher to host) Additional description Audio mute Audio mute on X@ *1Z X@ *1Z Amt X@ *1 ] S ...

  • Extron electronic ISS 506 - page 97

    4-25 ISS 506 Integration Seamless Switcher • SIS Programming and Contr ol Command/response table for SIS commands (continued) Command ASCII (T elnet) (host to switcher) URL Encoded (Web) (host to switcher) Response (switcher to host) Additional description Horizontal logo capture size Set a specific horizontal size 6* X1^ : 6* X1^ : 6Hsz X1^] Se ...

  • Extron electronic ISS 506 - page 98

    SIS Pr ogramming and Control, cont’d ISS 506 Integration Seamless Switcher • SIS Programming and Contr ol 4-26 Command/response table for SIS commands (continued) Command ASCII (T elnet) (host to switcher) URL Encoded (Web) (host to switcher) Response (switcher to host) Additional description Image recall (continued) Assign black screen to the ...

  • Extron electronic ISS 506 - page 99

    4-27 ISS 506 Integration Seamless Switcher • SIS Programming and Contr ol Command ASCII (T elnet) (host to switcher) URL Encoded (Web) (host to switcher) Response (switcher to host) Additional description Horizontal shift logo Set a specific horizontal position 5* X3% * X1& H 5* X3% * X1& H 5Hph X3% * X1&] Specify the horizontal posi ...

  • Extron electronic ISS 506 - page 100

    SIS Pr ogramming and Control, cont’d ISS 506 Integration Seamless Switcher • SIS Programming and Contr ol 4-28 Command ASCII (T elnet) (host to switcher) URL Encoded (Web) (host to switcher) Response (switcher to host) Additional description PIP window vertical shift Set a specific vertical position 3* X1& / 3* X1& / 3Vph X1&] Spec ...

  • Extron electronic ISS 506 - page 101

    4-29 ISS 506 Integration Seamless Switcher • SIS Programming and Contr ol Command ASCII (T elnet) (host to switcher) URL Encoded (Web) (host to switcher) Response (switcher to host) Additional description PIP image horizontal size Set a specific horizontal size 4* X1^ : 4* X1^ : 4Hsz X1^] Set the PIP image’s horizontal size to X1^ . Increment ...

  • Extron electronic ISS 506 - page 102

    SIS Pr ogramming and Control, cont’d ISS 506 Integration Seamless Switcher • SIS Programming and Contr ol 4-30 Command ASCII (T elnet) (host to switcher) URL Encoded (Web) (host to switcher) Response (switcher to host) Additional description PIP window configuration N The variables must be entered, and ar e returned, in the following order: ho ...

  • Extron electronic ISS 506 - page 103

    4-31 ISS 506 Integration Seamless Switcher • SIS Programming and Contr ol Command ASCII (T elnet) (host to switcher) URL Encoded (Web) (host to switcher) Response (switcher to host) Additional description V ertical position Specify a vertical position 7* X1& / 7* X1& / 7Vph X1&] Specify the vertical position of the scan converted outp ...

  • Extron electronic ISS 506 - page 104

    SIS Pr ogramming and Control, cont’d ISS 506 Integration Seamless Switcher • SIS Programming and Contr ol 4-32 Command ASCII (T elnet) (host to switcher) URL Encoded (Web) (host to switcher) Response (switcher to host) Additional description Scan converter flicker filter N The command (d) is case sensitive . Set flicker filter level 7* X4! ...

  • Extron electronic ISS 506 - page 105

    4-33 ISS 506 Integration Seamless Switcher • SIS Programming and Contr ol Command/response table for SIS commands (continued) N X! = Input number 1 – 6 X@ = Output 1 = Pr ogram 2 = Preview 3 = PIP window 4 = PIP image X1) = V ideo type (see page 4-5). X1% = Mute / Preset status 0 = off (video unmuted)/ not saved 1 = on (video muted) / saved X4# ...

  • Extron electronic ISS 506 - page 106

    SIS Pr ogramming and Control, cont’d ISS 506 Integration Seamless Switcher • SIS Programming and Contr ol 4-34 Command ASCII (T elnet) (host to switcher) URL Encoded (Web) (host to switcher) Response (switcher to host) Additional description Information requests (continued) Query part number N N 60-742- xx ] See appendix B for part numbers. V i ...

  • Extron electronic ISS 506 - page 107

    4-35 ISS 506 Integration Seamless Switcher • SIS Programming and Contr ol Command/Response T able for IP SIS Commands Symbol definitions X7) = Switcher name (Up to 240 alphanumeric characters) N The following characters are invalid in the name: {space} ~ , _ @ = ` [ ] { } < > ‘ “ ; : | and ?. X7! = Default name ISS-506-Series- + last ...

  • Extron electronic ISS 506 - page 108

    SIS Pr ogramming and Control, cont’d ISS 506 Integration Seamless Switcher • SIS Programming and Contr ol 4-36 Command ASCII (T elnet) (host to switcher) URL Encoded (Web) (host to switcher) Response (switcher to host) Additional description Interface ports configuration Set switcher name EX7) CN } W X7) CN | Ipn •X7)] Read switcher name E C ...

  • Extron electronic ISS 506 - page 109

    4-37 ISS 506 Integration Seamless Switcher • SIS Programming and Contr ol Command/response table for SIS commands (continued) Command ASCII (T elnet) (host to switcher) URL Encoded (Web) (host to switcher) Response (switcher to host) Additional description Read e-mail recipient EX8! CR } W X8! CR | X8@ , ] Y oumustrsthavesetan? ...

  • Extron electronic ISS 506 - page 110

    SIS Pr ogramming and Control, cont’d ISS 506 Integration Seamless Switcher • SIS Programming and Contr ol 4-38 Special Characters The HTML language reserves certain characters for specific functions. The switcher does not accept these characters as part of preset names, the switcher ’s name, passwords, or locally cr eated file names. The sw ...

  • Extron electronic ISS 506 - page 111

    ISS 506 Integration Seamless Switcher 5 Chapter Five Switcher Softwar e ISS 506 Control Program Button Label Generator Special Characters ...

  • Extron electronic ISS 506 - page 112

    ISS 506 Integration Seamless Switcher • Switcher Software 5-2 Switcher Softwar e ISS 506 Contr ol Program The W indows-based Extron ISS 506 Control Pr ogram, which communicates with the switcher via the RS-232/RS-422 port, the Configuration port, and the LAN port, provides an easy way to configur e and operate the ISS 506 Integration Seamless S ...

  • Extron electronic ISS 506 - page 113

    5-3 ISS 506 Integration Seamless Switcher • Switcher Software 4 . Follow the on-screen instructions. By default, the W indows installation of the Matrix Switchers Control Pr ogram creates a C:Pr ogram Files Extron ISS506, and it places four icons into a gr oup folder named “Extron ElectronicsMatrix Switchers.” The four installed icons ar ...

  • Extron electronic ISS 506 - page 114

    Switcher Softwar e, cont’d ISS 506 Integration Seamless Switcher • Switcher Software 5-4 Using the software Many items found in the ISS 506 Control Pr ogram are also accessible via fr ont panel controls (see chapter 3, “Operation”) and under SIS contr ol (see chapter 4, “SIS Programming and Contr ol”). The ISS 506 Help Program pr ovides ...

  • Extron electronic ISS 506 - page 115

    5-5 ISS 506 Integration Seamless Switcher • Switcher Software When the program starts satisfactorily , the Extron ISS 506 Contr ol Program Contr ol window (figure 5-4) appears. 4 . If you selected RS-232 in step 2 , click the Port drop box and select the comm port that is connected to the ISS 506 switcher ’s fr ont panel Configuration port or ...

  • Extron electronic ISS 506 - page 116

    Switcher Softwar e, cont’d ISS 506 Integration Seamless Switcher • Switcher Software 5-6 • TheProgramandPr eviewFreeze,inputselection,andLogo/Black buttons work exactly as similar buttons on the front panel.  For audio breakaway switching (audio or video switched separately from each other), click the desir ed ...

  • Extron electronic ISS 506 - page 117

    5-7 ISS 506 Integration Seamless Switcher • Switcher Software • ThePictureradiobuttonselectspictur econtroladjustmentsthatpr ovide thesamefunctionsasthePicture Adjustmentbuttonsonthefrontpanel (gure5-6).Seechapter3,“Operations“formor einformat ...

  • Extron electronic ISS 506 - page 118

    Switcher Softwar e, cont’d ISS 506 Integration Seamless Switcher • Switcher Software 5-8 I/O Configuration window The I/O Configuration window (figure 5-7) pr ovides a location for viewing and changing input and output configuration settings. The input configuration settings work similar to selections made on the front panel via the Input ...

  • Extron electronic ISS 506 - page 119

    5-9 ISS 506 Integration Seamless Switcher • Switcher Software Logo Setup/Capture window The Logo Setup/Capture window (figur e 5-8) consists of two areas: the logo capture ar ea (on the right) and the logo setup area (on the left). See chapter 3, “Operation”. Logo Setup Area Logo Capture Area Figure 5-8 — Logo Setup/Captur e window Capturi ...

  • Extron electronic ISS 506 - page 120

    Switcher Softwar e, cont’d ISS 506 Integration Seamless Switcher • Switcher Software 5-10 4 . Click in the Enter logo name field, type in a name for you logo, and click the Start Capture button. The pr ogram displays a window that shows the progr ess of the capture (figur e 5-9). Depending on the size of the logo, this can take a few minutes. ...

  • Extron electronic ISS 506 - page 121

    5-11 ISS 506 Integration Seamless Switcher • Switcher Software N As a simpler alternative, if you selected the Key T ype Color radio button, you can click the Pick Color button. The program pops up a window containing the logo and a color picker cursor (figure 5-1 1). Click the color picker cursor on the area that has the color that you want to ...

  • Extron electronic ISS 506 - page 122

    Switcher Softwar e, cont’d ISS 506 Integration Seamless Switcher • Switcher Software 5-12 Advanced Setup window The Advanced Setup window (figure 5-12) pr ovides a location for viewing and changing most advanced configuration settings. The advanced settings work similar to selections made on the front panel via the Advanced Configuration men ...

  • Extron electronic ISS 506 - page 123

    5-13 ISS 506 Integration Seamless Switcher • Switcher Software Scan Converter Setup window N The Scan Converter Setup tab and window are available only if your ISS has the optional scan converter output board installed (either included as delivered [ISS 506 SC or ISS 506 DI/SC] or installed after purchase [part # 70-486-01 ]. The Scan Converter S ...

  • Extron electronic ISS 506 - page 124

    Switcher Softwar e, cont’d ISS 506 Integration Seamless Switcher • Switcher Software 5-14 System Settings IP settings window The IP settings window (figur e 5-15) provides a location for viewing and, if it is connected via the RS-232/RS-422 link or if you are logged on via the LAN port as an administrator , editing settings unique to the Ether ...

  • Extron electronic ISS 506 - page 125

    5-15 ISS 506 Integration Seamless Switcher • Switcher Software Gateway eld The Gateway field identifies the address of the gateway to the mail server to be used if the switcher and the mail server are not on the same subnet. V alid IP addresses consist of four 1-, 2-, or 3-digit octets separated by dots (periods). Each octet can be numbered ...

  • Extron electronic ISS 506 - page 126

    Switcher Softwar e, cont’d ISS 506 Integration Seamless Switcher • Switcher Software 5-16 System Settings RS-232 window Figure 5-16 — System Settings RS-232 window Only the baud rate can be changed in the ISS 506 Control Pr ogram System Settings window; all other settings - Parity , Data Bits, Stop Bits, Flow Control, and Port T ype, ar e dis ...

  • Extron electronic ISS 506 - page 127

    5-17 ISS 506 Integration Seamless Switcher • Switcher Software System Settings Date/Time window Figure 5-17 — System Settings Date/Time window Sync Date & Time to PC button Click in the Sync Date & T ime to PC check box and then the Submit button to have the computer you are operating send its internal time to the switcher in a set time ...

  • Extron electronic ISS 506 - page 128

    Switcher Softwar e, cont’d ISS 506 Integration Seamless Switcher • Switcher Software 5-18 Time (local) eld The T ime (local) field displays the current time in the local time zone. If necessary , click on the Sync Date & T ime to PC button to set the switcher to your computer ’s internal time or else adjust the time manually as follow ...

  • Extron electronic ISS 506 - page 129

    5-19 ISS 506 Integration Seamless Switcher • Switcher Software N Editing the Administrator Password field while connected via the LAN port does not affect your current login. The administrator password r equirement takes affect at the next login. Extron r ecommends assigning an administrator ’ s password to qualified and knowledgeable personn ...

  • Extron electronic ISS 506 - page 130

    Switcher Softwar e, cont’d ISS 506 Integration Seamless Switcher • Switcher Software 5-20 6 . Start the ISS 506 Contr ol Program. See “Using the softwar e”, steps 1 through 4 , starting on page 5-4. 7 . Click Tools > Update firmware . The Extr on Firmware Loader port configuration window appears (figure 5-21). Figure 5-21 — Firmwar e ...

  • Extron electronic ISS 506 - page 131

    5-21 ISS 506 Integration Seamless Switcher • Switcher Software 10 . Click the OK button. The Extron Firmwar e Loader appears (figure 5-22). Figure 5-22 — Firmwar e loading 11 . Click Browse . The open file window appears. 12 . Navigate to the folder where you saved the firmwar e upgrade file. Select the file and click Open . The Firmware L ...

  • Extron electronic ISS 506 - page 132

    Switcher Softwar e, cont’d ISS 506 Integration Seamless Switcher • Switcher Software 5-22 Uploading images N The IP Link File Manager must be installed on your computer to perform this operation. Extron r ecommends that you install this program when you install the ISS 506 Control Pr ogram. If you did not, you can downloaded it from the Extron ...

  • Extron electronic ISS 506 - page 133

    5-23 ISS 506 Integration Seamless Switcher • Switcher Software Figure 5-24 — IP Link File Manager pr ogram window 5 . Check to see that the ISS contents include the directory “nortxe-graphics“. If the “nortxe-graphics“ directory is present in the ISS, proceed to step 6 . If the “nortxe-graphics“ directory is not present in the ISS, ...

  • Extron electronic ISS 506 - page 134

    Switcher Softwar e, cont’d ISS 506 Integration Seamless Switcher • Switcher Software 5-24 7 . Delete images from the ISS by clicking on them, pr essing the PC’s Delete key , and clicking Yes in the advisory box that appears. Windows menus File menu Reselect Connection ... — Disconnects computer from the ISS without closing the ISS 506 Contr ...

  • Extron electronic ISS 506 - page 135

    5-25 ISS 506 Integration Seamless Switcher • Switcher Software T ools menu Unit Info ... — Opens a window (figure 5-26) that provides basic information about the status of the ISS, including the model name and number , the installed daughterboards, the firmware version and build, and the internal temperature. Figure 5-26 — Unit Information ...

  • Extron electronic ISS 506 - page 136

    Switcher Softwar e, cont’d ISS 506 Integration Seamless Switcher • Switcher Software 5-26 Data View/Trace Window ... — Calls the trace log window (figure 5-26), which shows the serial communications, in ASCII and Hex, between the controller and the ISS. Reference to this window can be helpful when writing your own control scripts. Figure 5-2 ...

  • Extron electronic ISS 506 - page 137

    5-27 ISS 506 Integration Seamless Switcher • Switcher Software Using the help system For information about program featur es, you can access the help program in any of the following ways:  • FromtheExtr onElectronicspr ogramfolderorgroup, double-click on the ISS 506 Help icon (shown at right).  • Fromwithin ...

  • Extron electronic ISS 506 - page 138

    Switcher Softwar e, cont’d ISS 506 Integration Seamless Switcher • Switcher Software 5-28 Figure 5-29 — Extr on’ s Button Label Generator window 2 . Under System selection, choose SGS 408 (this selection matches the button size of the ISS 506). 3 . Using normal W indows controls, create and print the labels that ar e placed in the label win ...

  • Extron electronic ISS 506 - page 139

    ISS 506 Integration Seamless Switcher 6 Chapter 6 HTML Operation Downloading the Startup Page System Status T ab Configuration T ab File Management T ab Control T ab Special Characters ...

  • Extron electronic ISS 506 - page 140

    ISS 506 Integration Seamless Switcher • HTML Operation 6-2 HTML Operation The switcher can be controlled and operated thr ough its LAN port, connected via a LAN or W AN, using a web browser such as Microsoft’s Internet Explor er . The browser ’s display of the switcher ’s status or operation has the appearance of web pages. This chapter des ...

  • Extron electronic ISS 506 - page 141

    6-3 ISS 506 Integration Seamless Switcher • HTML Operation 7 . The switcher checks several possibilities, in the following order , and then responds accor dingly: • Does the address include a specific file name, such as 10.13.156.10/ file_name.html? If so , the switcher downloads that HTML page. • If not, is ther e a file in the switcher ...

  • Extron electronic ISS 506 - page 142

    HTML Operation, cont’d ISS 506 Integration Seamless Switcher • HTML Operation 6-4 Configuration T ab System Configuration page The ISS 506 switcher downloads the System Configuration page (figure 6-3) when you click the Configuration tab . The screen consists of fields in which you can view and edit IP administration and system settings. T ...

  • Extron electronic ISS 506 - page 143

    6-5 ISS 506 Integration Seamless Switcher • HTML Operation IP Address eld The IP Address field contains the IP addr ess of the connected switcher . This value is encoded in the switcher ’s flash memory . V alid IP addresses consist of four 1-, 2-, or 3-digit numeric subfields, pr operly called octets, separated by dots (periods). Each oct ...

  • Extron electronic ISS 506 - page 144

    HTML Operation, cont’d ISS 506 Integration Seamless Switcher • HTML Operation 6-6 3 . Repeat steps 1 and 2 for other variables that need to be changed. 4 . If appropriate, select the Daylight Saving radio button to turn on the daylight savings time feature. N When daylight saving time is turned on, the switcher automatically updates its interna ...

  • Extron electronic ISS 506 - page 145

    6-7 ISS 506 Integration Seamless Switcher • HTML Operation T o select and output a test pattern, use the T est Pattern dropbox in the Advanced Configuration area to select the desir ed pattern (Color Bars; crosshatch; 4 x 4 crosshatch; split grayscale; ramp; alternating pixels; cr op; or film aspect ratios of 1.78, 1.85, and 2.35), and then cli ...

  • Extron electronic ISS 506 - page 146

    HTML Operation, cont’d ISS 506 Integration Seamless Switcher • HTML Operation 6-8 Use the and buttons to increment and decrement the horizontal and vertical shift; horizontal and vertical size; and the flicker , horizontal, and encoder filters (or use the dropboxes for the filters). Passwords page Access the Passwords page (figur e 6-7) by ...

  • Extron electronic ISS 506 - page 147

    6-9 ISS 506 Integration Seamless Switcher • HTML Operation Email Alerts page Reach the Email Alerts page (figure 6-8) by clicking the Email Alerts link on the System Configuration page. The Email Alerts screen enables you to set up the ISS 506 to automatically send e-mail alert messages when settings are changed on the ISS 506. Y ou may enter u ...

  • Extron electronic ISS 506 - page 148

    HTML Operation, cont’d ISS 506 Integration Seamless Switcher • HTML Operation 6-10 T o set up e-mail addresses for notification, do the following for each recipient of e-mail alerts: 1 . Click the Edit button at the end of the address r ow . The Edit button changes to Save . 2 . Enter the e-mail address of the r ecipient, and the file name on ...

  • Extron electronic ISS 506 - page 149

    6-11 ISS 506 Integration Seamless Switcher • HTML Operation Update the switcher firmware as follows: N The Firmware Upgrade page is only for r eplacing the firmware that contr ols all switcher operation. T o insert your own HTML pages, see “File Management Page”, on page 6-12. 1 . V isit the Extron web site, www .extron.com , and click the ...

  • Extron electronic ISS 506 - page 150

    HTML Operation, cont’d ISS 506 Integration Seamless Switcher • HTML Operation 6-12 File Management T ab File Management page T o delete files such as logo bitmaps from the switcher or to upload your own HTML files to the switcher , click the File Management tab. The switcher downloads the File Management HTML page (figure 6-1 1). Figure 6-11 ...

  • Extron electronic ISS 506 - page 151

    6-13 ISS 506 Integration Seamless Switcher • HTML Operation Contr ol T ab User Control page Y ou can perform most of the front panel operations on the User Control page (figure 6-12). Access the User Control page by clicking the Control tab. The User Control page emulates the fr ont panel of the ISS and displays the current input selections and ...

  • Extron electronic ISS 506 - page 152

    HTML Operation, cont’d ISS 506 Integration Seamless Switcher • HTML Operation 6-14 Preset page Y ou can save and recall user presets and input pr esets from the Presets page (figure 6-13). Access the Presets page by clicking the Presets link on the User Control page. Refresh User Control PIP setup Logos Figure 6-13 — Pr esets page User prese ...

  • Extron electronic ISS 506 - page 153

    6-15 ISS 506 Integration Seamless Switcher • HTML Operation Input presets N User presets consist of: •  Filmmode • T otalpixels •  Programphase • Previewphase •  Horizontalstart • V erticalstart •  Horizontalactivepixels • V erticalactivepixels •  Horizontal ...

  • Extron electronic ISS 506 - page 154

    HTML Operation, cont’d ISS 506 Integration Seamless Switcher • HTML Operation 6-16 Logos page Y ou can assign images to either logo and set the variables associated with the logo function from the Logos page (figur e 6-15). Y ou can also upload your own images to serve as logos and delete unwanted images. Access the Logos page by clicking the ...

  • Extron electronic ISS 506 - page 155

    6-17 ISS 506 Integration Seamless Switcher • HTML Operation Figure 6-16 — Add Image field Deleting an image Delete an unwanted image as follows: 1 . In the Image Index Field, click the unwanted image. 2. Click the Delete button. The computer deletes the selected image from the ISS. Assigning (recall) a logo Assign a bitmap image to one of two ...

  • Extron electronic ISS 506 - page 156

    HTML Operation, cont’d ISS 506 Integration Seamless Switcher • HTML Operation 6-18 4 . W atch the logo on the connected output device while you slowly drag the slider up and down (figure 6-17) to key out unwanted material, such as the background, fr om the logo. Figure 6-17 — Set Logo Recall slider 5 . W atch the logo on the connected output ...

  • Extron electronic ISS 506 - page 157

    ISS 506 Integration Seamless Switcher 7 Chapter 7 Modifications Opening the Switcher Installing an Optional SDI/HD-SDI Input Board Installing an Optional Output Board Closing the Switcher Button Labels ...

  • Extron electronic ISS 506 - page 158

    ISS 506 Integration Seamless Switcher • Modications 7-2 Modifications The ISS 506 can be modified to install or remove optional boar ds that change the input and/or output formats that the switcher can process. The following optional I/O boards ar e available:  • SDI/HD-SDIinput  • Scanconverter(lowresolution)o ...

  • Extron electronic ISS 506 - page 159

    7-3 ISS 506 Integration Seamless Switcher • Modications 4 . Lift the top cover straight up approximately 5 inches until you can access the fan power cord. C Do not touch any electronic components inside the ISS. Doing so could damage the switcher . Electrostatic dischar ge (ESD) can damage IC chips even though you cannot feel it. Y ou must be ...

  • Extron electronic ISS 506 - page 160

    Modifications, cont’d ISS 506 Integration Seamless Switcher • Modications 7-4 3 . From the inside of the switcher , pop the cover out of the rear panel connector port ( c ). 4 . See figure 7-3. T ip the input board up and guide its output connector thr ough the rear panel connector port ( d ). 4 5 5 5 Figure 7-3 — Input boar d installati ...

  • Extron electronic ISS 506 - page 161

    7-5 ISS 506 Integration Seamless Switcher • Modications 7 . Secure the input boar d to the back panel with the included hex nut (figure 7-5). SDI S H RS232/422 VID /Y R-Y VID B-Y /C V G /Y R R-Y LAN RESET O U T P U T S 6 YC B/ B-Y PROGRAM PREV IEW RGB/ R-Y , Y , B-Y RGB/ R-Y , Y , B-Y 6 L R L R PREV IEW FIXED L R PROGRA M V AR IA B LE L R VID ...

  • Extron electronic ISS 506 - page 162

    Modifications, cont’d ISS 506 Integration Seamless Switcher • Modications 7-6 Installing an Optional Output Boar d Y ou can install one of three optional output boards in the ISS. W ith the board installed, the switcher outputs low resolution (scan converted) video, HD-SDI video, or DVI video on the appropriate connectors in parallel with t ...

  • Extron electronic ISS 506 - page 163

    7-7 ISS 506 Integration Seamless Switcher • Modications 3 . On the main board (figur e 7-7), locate connectors J1, J2A, and J2B ( b ); the standoff ( c ); and the r ear panel connector port ( d ). J1 2 J2A J2B 2 4 3 Figure 7-7 — Output boar d installation location N The HD-SDI and low resolution (scan converter) output daughterboards use co ...

  • Extron electronic ISS 506 - page 164

    Modifications, cont’d ISS 506 Integration Seamless Switcher • Modications 7-8 5 . See figure 7-9. Align the connector(s) on the output board with those on the extension(s) ( f ). Gently apply pressur e to carefully mate the output boar d with the extension(s). 6 6 6 6 7 7 Figure 7-9 — Output boar d installation Continue to apply pressure ...

  • Extron electronic ISS 506 - page 165

    7-9 ISS 506 Integration Seamless Switcher • Modications 6 . See figure 7-10. Secur e the output board to the standof f on the main board with the included screw ( h ). 8 Figure 7-10 — Secur e the output board to the standof f 7 . Secure the output boar d to the back panel with the two screws ( i ) r emoved in step 2 (figure 7-1 1). RS232/4 ...

  • Extron electronic ISS 506 - page 166

    Modifications, cont’d ISS 506 Integration Seamless Switcher • Modications 7-10 Closing the Switcher 1 . Reconnect the fan power cord to connector J46 on the main boar d. 2 . Replace the top cover on the ISS. 3 . Fasten it with the screws that wer e removed in “Opening the Switcher“, step 3 . 4 . Rack mount the switcher if desired and r ...

  • Extron electronic ISS 506 - page 167

    7-11 ISS 506 Integration Seamless Switcher • Modications Button label blanks ...

  • Extron electronic ISS 506 - page 168

    Modifications, cont’d ISS 506 Integration Seamless Switcher • Modications 7-12 ...

  • Extron electronic ISS 506 - page 169

    ISS 506 Integration Seamless Switcher A Appendix A Ether net Connection Ethernet Link Subnetting — A Primer ...

  • Extron electronic ISS 506 - page 170

    ISS 506 Integration Seamless Switcher • Ethernet Connection A-2 Ether net Connection Ether net Link The rear panel Ethernet connector on the ISS 506 can be connected to an Ethernet LAN or W AN. This connection makes SIS control of the switcher possible using a computer connected to the same LAN. Ethernet connection The Ethernet cable can be termi ...

  • Extron electronic ISS 506 - page 171

    A-3 ISS 506 Integration Seamless Switcher • Ethernet Connection Ping the switcher as follows: 1 . On the W indows task bar , click Start > Run. 2 . At the Open prompt, type command. 3 . Click the OK button. 4 . At the DOS prompt, type ping {IP addr ess} and then press Enter . The computer returns a display similar to figur e A-2. The line Pin ...

  • Extron electronic ISS 506 - page 172

    Ether net Connection, cont’d ISS 506 Integration Seamless Switcher • Ethernet Connection A-4 Microsoft (R) windows 2000 (TM) Version 5.0 (Build 2195) Welcome to Microsoft Telnet Client Telnet Client Build 5.00.99203.1 Escape Character is 'CTRL+]' Microsoft Telnet> Figure A-3 — T elnet screen T elnet tips It is not the intention o ...

  • Extron electronic ISS 506 - page 173

    A-5 ISS 506 Integration Seamless Switcher • Ethernet Connection Local echo Once connected to the ISS 506, by default, T elnet does not display your keystrokes on the screen. SIS commands ar e typed in blindly and only the SIS responses ar e displayed on the screen. T o command T elnet to show keystr okes, at the T elnet prompt, type set local_ech ...

  • Extron electronic ISS 506 - page 174

    Ether net Connection, cont’d ISS 506 Integration Seamless Switcher • Ethernet Connection A-6 Subnetting — A Primer It is not the purpose of this manual to describe TCP/IP protocol in detail. However , some understanding of TCP/IP subnetting (a subnet is a sub set of a net work — a set of IP devices that have portions of their IP addresses i ...

  • Extron electronic ISS 506 - page 175

    A-7 ISS 506 Integration Seamless Switcher • Ethernet Connection Determining whether devices are on the same subnet T o determine the subnet, the local device’s IP address is compared to the r emote device’s IP addr ess (figure A-6). Each address’s octets are compared or not compared , depending on the value in the related subnet mask octet ...

  • Extron electronic ISS 506 - page 176

    Ether net Connection, cont’d ISS 506 Integration Seamless Switcher • Ethernet Connection A-8 ...

  • Extron electronic ISS 506 - page 177

    ISS 506 Integration Seamless Switcher B Appendix B Refer ence Information Specifications Part Numbers and Accessories ...

  • Extron electronic ISS 506 - page 178

    ISS 506 Integration Seamless Switcher • Reference Information Refer ence Information B-2 Specifications Video input Number/signal type ..................... 4 RGBHV , RGBS, RGsB, RGBcvS, component video (interlaced or progr essive), S-video, composite video 1 component video (interlaced), S-video, composite video 1 S-video, composite video, or o ...

  • Extron electronic ISS 506 - page 179

    ISS 506 Integration Seamless Switcher • Reference Information B-3 Scaled resolution ........................... 640x480 1,2,3,4,5,6 , 800x600 1,2,3,4,5,6 , 852x480 1,2,3,4,5 , 1024x768 1,2,3,4 , 1024x852 1,2,3,4 ,1024x1024 1,2,3 , 1280x768 1,2,3,4 , 1280x1024 1,2,3 , 1360x765 1,2,3 , 1365x768 1,2,3 , 1365x1024 1,2 , 1366x768 1,2,3 , 1400x1050 1,2 ...

  • Extron electronic ISS 506 - page 180

    Refer ence Information, cont’d ISS 506 Integration Seamless Switcher • Reference Information B-4 Audio output Number/signal type ..................... 3 stereo, balanced/unbalanced (2 pr ogram, 1 preview) Connectors ..................................... (3) 3.5 mm captive screw connector , 5 pole Impedance ...................................... ...

  • Extron electronic ISS 506 - page 181

    B-5 ISS 506 Integration Seamless Switcher • Reference Information Part Numbers and Accessories ISS 506 part numbers The following ISS 506 models are available: Switcher model Part number ISS 506 60-742-01 ISS 506 DI/DVI (SDI/HD-SDI input and DVI output) 60-742-12 ISS 506 SC (scan converted output) 60-742-03 ISS 506 DI/SC (SDI/HD-SDI input and sca ...

  • Extron electronic ISS 506 - page 182

    Refer ence Information, cont’d ISS 506 Integration Seamless Switcher • Reference Information B-6 ...

  • Extron electronic ISS 506 - page 183

    Extr on W arranty Extron Electr onics warrants this product against defects in materials and workmanship for a period of three years fr om the date of purchase. In the event of malfunction during the warranty period attributable directly to faulty workmanship and/or materials, Extr on Electronics will, at its option, repair or r eplace said product ...

  • Extron electronic ISS 506 - page 184

    © 2009 Extron Electr onics. All rights r eserved. Ex tron US A - We st Headquar te rs +8 00 .6 33 .9 87 6 Insid e U S A / C anad a O nl y +1 .7 14 .4 91 .1 50 0 +1 .7 14 .4 91 .1 51 7 FA X Ex tron US A - East +8 00 .6 33 .9 87 6 Insid e U S A / C anad a O nl y +1 .9 19 .8 63 .1 79 4 +1 .9 19 .8 63 .1 79 7 FA X Ex tron Europ e +8 00 .3 98 7. 66 73 ...

Fabricant Extron electronic Catégorie Switch

Les documents que nous recevons du fabricant de l'appareilExtron electronic ISS 506 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Extron electronic
- manuels d’utilisations ISS 506
- fiches produit Extron electronic
- dépliants
- ou étiquettes-énergie Extron electronic ISS 506
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Extron electronic ISS 506.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Extron electronic ISS 506, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Extron electronic ISS 506. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Extron electronic ISS 506.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Extron electronic ISS 506, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Extron electronic ISS 506 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Extron electronic ISS 506.

Le manuel d’utilisation complet Extron electronic, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Extron electronic ISS 506 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Extron electronic ISS 506, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lExtron electronic ISS 506 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Extron electronic ISS 506 - qui devraient nous aider dans les premières étapes lors de l'utilisation Extron electronic ISS 506
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Extron electronic ISS 506
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Extron electronic ISS 506 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Extron electronic ISS 506?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Extron electronic ISS 506, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Extron electronic ISS 506 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)