Français dropdown-ico

Manuel d’utilisation Hubbell Electric Heater Company V20

27 pages 3.62 mb
Télécharger

Aller à la page of 27

Summary
  • Hubbell Electric Heater Company V20 - page 1

    OPERATING AND MAINTENANCE MANUAL FOR ELECTRIC INDUSTRIAL PROCESS WATER HEATER ELECTRIC HEATER COMPANY BASE MODEL “ V10 and V20 ” ...

  • Hubbell Electric Heater Company V20 - page 2

    2 HUBBELL ELECTRIC HEATER COMPANY P.O. BOX 288 STRATFORD, CT 06615 PHONE: (203) 378-2659 FAX: (203) 378-3593 INTERNET: http://www.hubbellheaters.com/ -- IMPORTANT -- Always reference the f ull model number and serial num ber when calling the factory. WARNING / CAUTION 1. Tank is to be complete ly filled with water and all a ir is to be vented befor ...

  • Hubbell Electric Heater Company V20 - page 3

    3 TABLE OF CONTENTS SECTION TITLE PAG E # I GENERAL DESCRI PTION AND CONSTRUCTION 5 II I NSTALL ATI ON 10 III S C H E D U LE D M A IN T E NANCE AND OPERATION 16 I V TROUBLESHOOTI NG 18 V S E R V I C I N G & R E P L A C E M E N T O F P A R T S 2 0 VI MI SCELLANEOUS CHARTS AND FORMULAS 26 ...

  • Hubbell Electric Heater Company V20 - page 4

    4 ...

  • Hubbell Electric Heater Company V20 - page 5

    5 SECTION I - GENERAL DESCRIPTION AND CONST RUCTION GENERAL DESCRIPTION This booklet describes an electric water heater designed for use in an industrial or commercial application. The complete assembly consists of the storage tank, immersion electric heating element(s), thermostat, safety relief valve, safety high temperature cut out, ma gnetic co ...

  • Hubbell Electric Heater Company V20 - page 6

    6 CONTROL THERMOS TAT The water heater is supplied with a single stage immersion the rmostatic switch that i s install ed and wired at the factory. The thermostat can be adjusted through a range of 100° - 195° F, (an optional low range, 30° - 110° F, is available), and is adjustable with a flat tip screwdriver. Other thermostati c controls are ...

  • Hubbell Electric Heater Company V20 - page 7

    7 OUTER SHELL, INSULATION, AND SUPP ORTS The tank is encapsulated in 2-inches of high-density fiberg lass insulation. The protective shell is constructed of galvaneel and is coated with a durable silver hammertone finish. Heavy gaug e steel support legs are provided. OPTIONS The following optional features may be included in y our water heater. Ref ...

  • Hubbell Electric Heater Company V20 - page 8

    8 Dial Temperature an d Pressure Gauge A combination temperature (70° - 250° F) and pressure (0 – 200 psi) gaug e with 2½-inch dial may be supplied for in- line installation (shipped loose). Vacuum Relief Valve A vacuum relief valve may be provided with the unit to reduce the risk of back siphonage and back pressure of the sy stem. The valve w ...

  • Hubbell Electric Heater Company V20 - page 9

    9 Building Management System (BMS) A Building Manag ement Sy stem control package may be supplied for remote operation and alarm capabilitie s. Pump Interlock Term inal Block An optional pump interlock terminal block may be installed to prevent energizing when the pump is not running. Silicon Control Re ctifier A silicon control rectifier (SCR) “ ...

  • Hubbell Electric Heater Company V20 - page 10

    10 SECTION II – INSTALLATION WARNING / CAUTION DO NOT TURN ON THE ELECTRI C POWER SUPPLY to this equipment until he ater is completely fille d with water and all air has been relea sed. If the heater is NOT fille d with water when the power is turned on, the heating elements will burn out. For protection against excessive pressures and temperatur ...

  • Hubbell Electric Heater Company V20 - page 11

    11 4. I nstall the combination temperature and pressure safety relief valve in the tapping provided. Note that this is required by law for safety considerations. Outlet to floor drain I nstall into provided tapping Manual Release Lev e r Temperature Probe Temperature and Pressure Relief Valve 5. I nstall a relief valve overflow pipe to a nearby flo ...

  • Hubbell Electric Heater Company V20 - page 12

    12 FINAL CHECKS 1. Check all connections for tightness. 2. Ensure that all the above steps are completed 3. After the wa ter is heated for the first time, monitor the water te mperature as de scribed in S e c t i o n III, Q u a r t e r l y In s p e c t i on. Outgoing Hot Water I ncoming Cold Wate r 1 – V Model Water Heater 2 – Pressure and Temp ...

  • Hubbell Electric Heater Company V20 - page 13

    13 1 – Terminal Block 2 – Magnetic Contactor 3 – Heating Element 4 – Low Water Cut-Off, if supplied 5 – Transformer, 480-Volt/240-Volt, installed on 480-Volt models with low water cut-off only 6 – High-Te mperature L imit Switch 7 – Control Thermostat ...

  • Hubbell Electric Heater Company V20 - page 14

    14 1 – Terminal Block 2 – Magnetic Contactor 3 – Heating Element 4 – Low Water Cut-Off, if supplied 5 – Transformer, 480-Volt/240-Volt, installed on 480-Volt models with low water cut-off only 6 – High-Te mperature L imit Switch 7 – Control Thermostat ...

  • Hubbell Electric Heater Company V20 - page 15

    15 ...

  • Hubbell Electric Heater Company V20 - page 16

    16 SECTION III - SCHEDULED MAINTE NANCE AND OPERATION WARNING / CAUTION Before performing any maintenance procedure, make certain power supply is OFF and cannot accidentally be turned on. MAINTENANCE AND OPERATION The water heater is automatic in its operation. I t will maintain a full tank of water at the temperature setting of the thermostat. The ...

  • Hubbell Electric Heater Company V20 - page 17

    17 ANNUAL INSPECTION 1. Flush tank as follows a. Shut off power supply . b. Close valve on hot water outlet piping. c. Open valve on drain piping. d. Cold water inlet line pressure will be strong enough to flush sediment from the bottom of the tank out through the drain. L et water run for 3-4 minutes. e. Close drain valve. f. Open hot water valve. ...

  • Hubbell Electric Heater Company V20 - page 18

    18 SECTION IV – TROUBLESHOOTING Symptom Probable Cause Corrective Action / Remedy Circuit breaker tripped at source. Reset circuit breaker. Blown fuse in transformer, if installed. Replace fuse. Circuit breaker at control cabinet tripped, if installe d. Reset circ uit breaker. Blown fuse in element fuse block, if installed. Replace fuse. High lim ...

  • Hubbell Electric Heater Company V20 - page 19

    19 Faulty thermosta t. Check thermostat adjustment. Monitor thermostat as described i n S e c t i o n III, Q u a r t e r l y I nspection. Replace if necessary. Heating e lement not working on all phases Check to see that heating element is working on all phases, by checking the resistance (ohms) value for each element and c omparing with the chart ...

  • Hubbell Electric Heater Company V20 - page 20

    20 SECTION V - SERVICING & REPLACEMENT OF PARTS WARNING / CAUTION Before servicing or replacing any part make sure to turn the power supply switch to the OFF position. SURFACE TEMPERATURE HIGH LIMIT CUT -OFF 1. Disconnect power from unit. 2. Remove access cover. 3. Disconnect the four (4) 14 gauge wires. Control Wires 4. Remove the two (2) moun ...

  • Hubbell Electric Heater Company V20 - page 21

    21 IMMERSION TEMPERATURE HIGH L IMIT CUT-OFF 1. Disconnect power from unit. 2. Remove access cover. 3. Remove high limit c over screw and c over. Cover Cover Screw Reset Switch 4. Disconnect the two (2) 14 gauge wires. Wires Capillary Tube 5. Remove capilla ry tube and bulb from ther mowell 6. Remove two (2) mounting screws. Mounting Screws 7. Remo ...

  • Hubbell Electric Heater Company V20 - page 22

    22 HEATING ELEM ENT 1. Disconnect power from unit. 2. Shut off incoming water supply . 3. Attach hose to drain connection. 4. Lift manual release lever on relief valve to let air into sy stem or break union on outg oing water line. 5. Drain water from tank. 6. Disconnect the wires from the heatin g element terminal s. 7. Remove the 3/8-16 nuts. Tan ...

  • Hubbell Electric Heater Company V20 - page 23

    23 IMMERSION THE RMOSTAT 1. Disconnect power from unit. 2. Remove access cover and locate t hermostat. 3. Remove high limit c over screw and c over. Cover Cover Screw 4. Disconnect the two (2) 14 gauge wires. Wires Capillary Tube 5. Remove capilla ry tube and bulb from thermowe ll. 6. Remove two (2) mounting screws. Mounting Screws 7. Replace therm ...

  • Hubbell Electric Heater Company V20 - page 24

    24 MAGNETIC CONTACTOR 1. Disconnect power from unit. 2. Disconnect line and load wires to contactor. 3. Disconnect two (2) 14 gaug e control circuit wires. Control Wires Line Wires Load Wires 4. Loosen two (2) holding screws and remove contactor. Mounting Screws (Bottom screw not shown) 5. Replace with new cont actor using reverse procedure. ...

  • Hubbell Electric Heater Company V20 - page 25

    25 RELIEF VALVE 1. Disconnect power from unit. 2. Shut off incoming water supply . 3. Lift test lever on relief valve to relieve pressure in tank. 4. Disconnect overflow piping. 5. Unscrew relief valve, remove assemb ly and replace with new one. 6. Connect overflow piping. 7. Turn on incoming water supply and check for leaks. 8. Turn safety switch ...

  • Hubbell Electric Heater Company V20 - page 26

    26 SECTION VI – MISCELL ANEOUS CHARTS AND FORMULAS ELEMENT CHA RT Power (kW) Resistance (Ohms) Element Part # 208V 240V 480V I mmersion L ength Hairpin 1 Φ 3 Φ DELTA 3 Φ WYE CH-FO 608 6 ---- ---- 13 3/8" 7.2 7.2 ---- ---- CH-FO 604 4.5 6 ---- 13 3/8" 9.6 9.6 ---- ---- 4-38683N 4 5 6 13" 34.4 11.5 34.4 23.0 5-38683N 5 6 8 13" ...

  • Hubbell Electric Heater Company V20 - page 27

    27 TORQUE VALUE S BOLT SIZE 18-8 S/S IN. - LB S . BRASS IN. - LB S . SI LI CON BRONZE IN. - LB S . ALUMI NUM 2024-T4 IN. - LB S . 316 S/S IN. - LB S . MONEL IN. - LB S . 4-40 5.2 4.3 4.8 2.9 5.5 5.3 4-48 6.6 5.4 6.1 3.6 6.9 6.7 5-40 7.7 6.3 7.1 4.2 8.1 7.8 5-44 9.4 7.7 8.7 5.1 9.8 9.6 6-32 9.6 7.9 8.9 5.3 10.1 9.8 6-40 12.1 9.9 11.2 6.6 12.7 12.3 8 ...

Fabricant Hubbell Electric Heater Company Catégorie Water Heater

Les documents que nous recevons du fabricant de l'appareilHubbell Electric Heater Company V20 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Hubbell Electric Heater Company
- manuels d’utilisations V20
- fiches produit Hubbell Electric Heater Company
- dépliants
- ou étiquettes-énergie Hubbell Electric Heater Company V20
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Hubbell Electric Heater Company V20.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Hubbell Electric Heater Company V20, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Hubbell Electric Heater Company V20. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Hubbell Electric Heater Company V20.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Hubbell Electric Heater Company V20, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Hubbell Electric Heater Company V20 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Hubbell Electric Heater Company V20.

Le manuel d’utilisation complet Hubbell Electric Heater Company, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Hubbell Electric Heater Company V20 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Hubbell Electric Heater Company V20, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lHubbell Electric Heater Company V20 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Hubbell Electric Heater Company V20 - qui devraient nous aider dans les premières étapes lors de l'utilisation Hubbell Electric Heater Company V20
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Hubbell Electric Heater Company V20
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Hubbell Electric Heater Company V20 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Hubbell Electric Heater Company V20?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Hubbell Electric Heater Company V20, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Hubbell Electric Heater Company V20 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)