Français dropdown-ico

Manuel d’utilisation Carrier 30XW325-400

32 pages 2.48 mb
Télécharger

Aller à la page of 32

Summary
  • Carrier 30XW325-400 - page 1

    Copyright 2009 Carrier Cor poration F orm 30XW-2PD Carrier's AquaForce 30XW chillers provid e a great co mbination of perf or- mance and compact f ootpr int f or cooling and heat reco very applica- tions. These chillers pro v ide e xcellent reliability and efficiency at true operat- ing conditions without comp romising the en vironment. • Ch ...

  • Carrier 30XW325-400 - page 2

    2 Easy installation The AquaForce ® 30XW screw chillers are shipped with starter and unit mounted flow switch installed and can be shipped with a full R-134a refriger- ant charge to minimize installation time. The unit provides single point power connection (using optional con- trol power transfor mer) and quick, easy piping connections (using Vic ...

  • Carrier 30XW325-400 - page 3

    3 of the system. The AquaForce ® 30XW chiller's positive pressu re design ensures that air , moisture and other per for mance degrading contamina nts are not sucked inside the chiller . Pur ge units and their associated maintenance are no longer ne cessary. Refrigerant isolation valves The refrigerant isolation valves ena ble service personne ...

  • Carrier 30XW325-400 - page 4

    4 Extensive service menu Unauthorized access to the service menu can be password-protected. Built-in diagnostic capa bilities assist in troubles hooting and recommend proper corrective action for pre-set alar ms, resulting in greater up time. Alarm file This file maintains the last 50 time and date-stamped alar m and alert messages in memory. This ...

  • Carrier 30XW325-400 - page 5

    5 Model number nomenc lature a30-4744 3 0XW – 3 25 6 – – – 4 – 3 B 3 0XW – A qua Force ® W a ter-Cooled S crew Chiller De s i g n S erie s Unit S ize (Nominal Ton s ) (kW) 3 25 – 3 25 (11 33 ) 3 50 – 3 50 (1206) 400 – 400 (1 3 54) Volta g e 1 – 575- 3 -60 2 – 38 0- 3 -60 4 – 2 3 0- 3 -60 6 – 460- 3 -60 7 – 200- 3 -60 Co ...

  • Carrier 30XW325-400 - page 6

    6 LEGEND NO TES: 1. Cer tified in accordance with AHRI Standard 550/590 at standard rating conditions. 2. Standard rating conditions are as follows: Evapor ato r Conditions: Leaving W ater T emperature: 44 F (6.7 C ) Flow: 2.4 gpm per ton (0.043 L/s per kW) Condenser Conditions: Entering Water T emperature: 85 F (29.4 C) Flow: 3.0 gpm per ton (0.05 ...

  • Carrier 30XW325-400 - page 7

    7 30XW325-400 UNIT PHYSICAL DA T A — ENGLISH LEGEND 30XW UNIT SIZE 325 350 400 NOMINAL CAPACITY (tons) 325 350 400 UNIT WEIGHT (lb) (Operating/Shipping) 14,319/13,163 14,515/13,369 14,759/13,489 COMPRESSORS Semi-hermetic, twin screw Compressor Speed (rpm) 3500 Compressor Model Number (qty) 06TU483 (2) 06TU554 (2) Unloading T ype Slide V alve Mini ...

  • Carrier 30XW325-400 - page 8

    8 30XW325-400 UNIT PHYSICAL DA T A — SI LEGEND 30XW UNIT SIZE 325 350 400 NOMINAL CAP ACITY (kW) 1133 1206 1354 UNIT WEIGHT (kg) (Operating/Shipping) 6495/5971 6584/6064 6695/6119 COMPRESSORS Semi-hermetic, twin screw Compressor Speed (r/s) 58.3 Compressor Model Number (qty) 06TU483 (2) 06TU554 (2) Unloading T ype Slide V alve Minimum Step Capaci ...

  • Carrier 30XW325-400 - page 9

    9 Factory-installe d options Navigator™ module provides a portable, hand-held dis- play for convenient access to unit status, operation, config- uration and troubleshooting diagnostics capability. The four-line, 20-character LCD (liquid crystal display) display provides clear language infor mation in English, French, Spanish, or Portugu ese. The ...

  • Carrier 30XW325-400 - page 10

    10 temperature sensor to facilitate operating in HEA T mode. Heat machine units require 300 psig (2068 kPa) option and field-installed ther mal in sulation on the compressor dischar ge piping and waterbox heads beca use of high temperature. One-pass condenser provides a lower pressure drop through the condenser for applications with low delta T (te ...

  • Carrier 30XW325-400 - page 11

    11 FIELD-SUPPLIED AND FIELD-INSTALLED I NSULATION CONDEN S ER W A TERBO X IN S ULA TION NEEDED (HEA T MACHINE UNIT S ONL Y) CONDEN S ER W A TERBO X IN S ULA TION NEEDED (HEA T MACHINE UNIT S ONL Y) EV APORA T OR WA TERBO X IN S ULA TION NEEDED EV APORA T OR WA TERBO X IN S ULA TION NEEDED EV APORA T OR WA TERBO X IN S ULA TION NEEDED DI S CHARGE PI ...

  • Carrier 30XW325-400 - page 12

    12 Dimensions 30XW UNIT DIMENSIONS 30XW UNIT AND W A TERBOX DIMENSIONS NOTES: 1. Operating weight includes weight of water , refrige rent, and oil. 2. Denotes center of gravity . 3. Dimensions shown in ft-in. [mm] unless noted. 4. The recommended ser vice clearance around the machine is 3 ft [914.4 mm]. 5. Victaulic nozzles are standard on all unit ...

  • Carrier 30XW325-400 - page 13

    13 30XW UNIT DIMENSIONS (cont) D DI S CHARGE END S UCTION END a30-4747 INCOMING C ONTROL INCOMING C ONTR OL POWER 1 x 7/8” POWER 1 x 7/8” KNOCKOUT KNOCKOUT DOOR CLEARANCE SP ACE DOOR CLEARANCE SP ACE DI S CHARGE END S UCTION END a30-4748 EV AP 3 3/16” [81 mm] a30-4755 ...

  • Carrier 30XW325-400 - page 14

    14 Dimensions (cont) 30XW UNIT DIMENSIONS (cont) W A TERBO X FLANGE DET AIL a30-4725 UNIT NUMBER OF P ASSES A in. (mm) B in. (mm) CONNECTION SIZE Flange Vict aulic 30XW325-400 26 1 / 16 (154) 6 1 / 16 (154) 6 8 10 ( 0 ) 0 ( 0 ) 6 8 36 1 / 16 (154) 6 1 / 16 (154) 6 8 UNIT NUMBER OF P ASSES A in. (mm) B in. (mm) CONNECTION SIZE Flange Victaulic 30XW3 ...

  • Carrier 30XW325-400 - page 15

    15 Carrier’s packaged selection program provides quick, easy selection of Carrier’s water-cooled chillers. The pro- gram considers specific temperature, fluid and flow requirements among other factor s such as fouling and alti- tude corrections. Before selecting a chiller , consider the follo wing points: Leaving water (fluid) temperature (L WT ...

  • Carrier 30XW325-400 - page 16

    16 P erformance data (cont) 30XW325-400 EVAPORATOR MARINE W ATERBOX 0 500 1000 1500 2000 2500 3000 (0) (31.5) (63.1) (94.6) (126.2) (157.7) (189.3) 3 2 1 pass pass pass gpm (L/s) Evaporator Flow Rate 0.00 5.00 10.00 15.00 20.00 25.00 30.00 35.00 40.00 ft wg (0) (14.9) (29.8) (44.8) (59.7) (74.6) (89.5) (104.4) (119.4) (kPa) Pressure Drop NO TE : Th ...

  • Carrier 30XW325-400 - page 17

    17 3 0 500 1000 1500 2000 2500 3000 (0) (31.5) (63.1) (94.6) (126.2) (157.7) (189.3) Evaporator Flow Rate 2 1 pass pass pass 0.00 5.00 10.00 15.00 20.00 25.00 30.00 35.00 40.00 ft wg (0) (14.9) (29.8) (44.8) (59.7) (74.6) (89.5) (104.4) (119.4) (kPa) Pressure Drop gpm (L/s) 30XW325-400 EVAPORATOR NIH VICTAULIC LEGEND NO TE: T he table abo ve repres ...

  • Carrier 30XW325-400 - page 18

    18 P erformance data (cont) 0.00 5.00 10.00 15.00 20.00 25.00 30.00 35.00 40.00 ft wg (0) (14.9) (29.8) (44.8) (59.7) (74.6) (89.5) (104.4) (119.4) (kPa) 0 500 1000 1500 2000 2500 (0) (31.5) (63.1) (94.6) (126.2) (157.7) Condenser Flow Rate Pressure Drop 2 pass 1 pass gpm (L/s) 30XW325-400 CONDENSER NIH FLANGE LEGEND NO TE: The table abov e represe ...

  • Carrier 30XW325-400 - page 19

    19 Micropr ocessor The chiller microprocessor contro ls overall unit operation and controls a number of processes simultaneously. These processes include inter nal time rs, reading inputs, analog to digital conversions, display cont rol, diagnostic control, out- put rela y control, de mand li mit, capacity control, head pressure control, and temper ...

  • Carrier 30XW325-400 - page 20

    20 • Evaporator entering fluid temperature (T2) • Suction gas temperature (T4 - Circuit A, T7 - Circuit B) • Economizer gas temperature (T5 - Circuit A, T11 - Circuit B) (sizes 350, 400 only) • Space temperature (T8) • Discharge gas temperature (T9 - Circuit A, T10 - Circuit B) • Condenser entering fluid temperature (T12) • Condenser ...

  • Carrier 30XW325-400 - page 21

    21 T ypical contr ol wiring schematics 30XW UNIT CONTROL WIRING SCHEMA TIC LEGEND AW G — American Wire Gag e NEC — National Electrical Code CB — Circuit Break er PMP — Chilled W ater Pump COM — Communication P or t PMPI — Chilled W ater Pump Interlock EMM — Energy Management Module TB — Te r m i n a l B l o c k EQUIP GND — Equipme ...

  • Carrier 30XW325-400 - page 22

    22 Unit storage Store chiller and starter indoors, protected from construc- tion dirt and moisture. Inspect under shipping tarps, bags, o r cr at e s t o b e s u r e w at er h a s not collected during transit. Keep protec tive shipping co ve rs in place until machine is ready for installation. Assure th at the inside of the protec- tive cover meets ...

  • Carrier 30XW325-400 - page 23

    23 V ariable evaporator flow rates V ariable flow rates may be applied to a stan dard chiller . The unit will, however , attempt to maintain a constant leaving fluid temperature. In such cases minimum flow must be in excess of minimum flow gi ven in the Evaporator and Condenser Flow Rates table, and mini- mum loop volume must be in excess of 3 gall ...

  • Carrier 30XW325-400 - page 24

    24 Consider adding additional piping and iso lation valves to isolate each chiller to allow for service on the machine, and still allow for partial capacity from the other chiller . Even if evaporators are piped in series, parallel con- denser piping should be considered on con stant speed chillers to maximize ca pacity and efficiency while minimiz ...

  • Carrier 30XW325-400 - page 25

    25 T ypical piping and wiring TYPICAL PIPING AND WIRING FOR 30X W EV APORA TOR AND CONDENSER EV APORA TOR SHUT -OFF VA L V E BALANCING VA L V E TO COOLING LOAD FROM COOLING LOAD CONDENSER WA TER INLET CONDENSER WA TER OUTLET VIBRA TION ISOLA TION VIBRA TION ISOLA TION VIBRA TION ISOLA TION PRESSURE GAGE SHUT -OFF VA L V E CONDENSER 30XW DRAIN OUTLE ...

  • Carrier 30XW325-400 - page 26

    26 STANDARD SINGLE INPUT POWER CONFIGURATION LEGEND NO TE S: 1. Each main power sour ce must be supplied fr om a field-suppl ied fused electr ical ser vice with a (factor y-inst alled or field- installed) dis connect located in sig ht from the unit. 2. Control circuit po wer must be supplied fr om a separate sourc e through a field-sup plied discon ...

  • Carrier 30XW325-400 - page 27

    27 OPTIONAL DUAL INPUT POWER CONFI GURATION LEGEND NO TE S: 1. Each main power source must be supplied from a field-suppl ied fused electr ical ser vice with a (f actor y-installe d or field-ins talled) dis connect located in sig ht from the unit. 2. Control cir cuit power must be supplied from a separate source th rough a field-supp lied disconnec ...

  • Carrier 30XW325-400 - page 28

    28 COMPRESSOR ELECTRICAL DA T A LEGEND 30HX UNIT SIZE V O LTA G E V- P h - H z COMPRESSOR COMPRESSOR A COMPRESSOR B RLA LRA (WD) LRA ( XL) RLA LRA (WD) LRA (XL) 325 200-3-60 06TU483 409.0 938 N/A 409.0 938 N/A 230-3-60 06TU483 355.1 816 N/A 355.1 816 N/A 380-3-60 06TU483 216.7 494 1537 216.7 494 1537 460-3-60 06TU483 178.2 408 1270 178.2 408 1270 5 ...

  • Carrier 30XW325-400 - page 29

    29 W ater-Cooled Chiller HV AC Guide Specifications Size Range: 325 to 400 Nomin al T ons (1133 to 1354 kW) Carrier Model Number: 30XW Part 1 — General 1.01 SYSTEM DESCRIPTION Microprocessor controlled water -cooled liquid chiller utilizing screw compressor s and electronic expan- sion valves. 1.02 QUALITY ASSURANCE A. Unit shall be rated in ac c ...

  • Carrier 30XW325-400 - page 30

    30 compressor discharge piping and waterb ox heads becau se of high tempera ture. F . Refrigeration Compone nts: Refrigerant circuit components shall include oil sep- arator , high and low side pr essure relief devices, dis- charge and liquid line shutoff valves, filter drier , moisture indicating sight glass, expansion valve, refrigerant economize ...

  • Carrier 30XW325-400 - page 31

    31 m. Time of day: 1) Display module, in conjunction with the microprocessor , must al so be capable of displaying the output (results) of a ser- vice test. Service test shall verify opera- tion of every switch, ther mistor , and compressor before chiller is started. 2) Diagnostics shall in clude the ability to review a list of the 30 most recent a ...

  • Carrier 30XW325-400 - page 32

    Manufacturer reserves the right to dis continue, or change at any time, specifications or d esigns without notice and without inc urring obligations. Pg 32 Catalog No . 04-52300015-01 Printed in U .S.A . Form 30XW -2PD Replaces: 30XW -1PD Carrier Cor poration • Syracuse, New Y ork 13221 6-09 Section 9 Ta b 9 a 12. Compressor Suction Service V alv ...

Fabricant Carrier Catégorie Water Dispenser

Les documents que nous recevons du fabricant de l'appareilCarrier 30XW325-400 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Carrier
- manuels d’utilisations 30XW325-400
- fiches produit Carrier
- dépliants
- ou étiquettes-énergie Carrier 30XW325-400
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Carrier 30XW325-400.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Carrier 30XW325-400, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Carrier 30XW325-400. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Carrier 30XW325-400.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Carrier 30XW325-400, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Carrier 30XW325-400 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Carrier 30XW325-400.

Le manuel d’utilisation complet Carrier, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Carrier 30XW325-400 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Carrier 30XW325-400, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lCarrier 30XW325-400 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Carrier 30XW325-400 - qui devraient nous aider dans les premières étapes lors de l'utilisation Carrier 30XW325-400
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Carrier 30XW325-400
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Carrier 30XW325-400 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Carrier 30XW325-400?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Carrier 30XW325-400, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Carrier 30XW325-400 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)