Français dropdown-ico

Manuel d’utilisation Stow SMC3PE

42 pages 1.99 mb
Télécharger

Aller à la page of 42

Summary
  • Stow SMC3PE - page 1

    © COPYRIGHT 2003, MUL TIQUIP INC . P AR TS AND OPERA TION MANUAL POR TO MIX MINI CONCRETE MIXER PLASTIC DRUM MODELS SMC3PE AND SMC3PB Re vision #0 (08/08/03) P ARTS DEP A RTMENT : 800-427-1244 F AX: 800-672-7877 SERVICE DEP AR TMENT/TECHNICAL ASSIST ANCE: 800-478-1244 F AX: 310-631-5032 STOW CONSTRUCTION EQUIPMENT STOW CONSTRUCTION EQUIPMENT STOW ...

  • Stow SMC3PE - page 2

    ...

  • Stow SMC3PE - page 3

    STOW PORTO MIXER — PARTS & OPERATION MANUAL — REV. #0 (08/09/02) — PAGE 3 HERE'S HOW TO GET HELP PLEASE HA VE THE MODEL AND SERIAL NUMBER ON-HAND WHEN CALLING P AR TS DEP AR TMENT 800-427-1244 or 310-537-3700 F AX: 800-672-7877 or 310-637-3284 SER VICE DEP AR TMENT 800-478-1244 F AX: 310- 537-4259 TECHNICAL ASSIST ANCE 800-478-1244 F ...

  • Stow SMC3PE - page 4

    P A GE 4 —ST O W POR T O MIXER — P ARTS & OPERA TION MANUAL — REV . #0 (08/08/03) T ABLE OF CONTENTS Here's How T o Get Help ............................................ 3 T able Of Contents ..................................................... 4 P ar ts Order ing Procedures ....................................... 5 STOW PORTO MIXER ...

  • Stow SMC3PE - page 5

    STOW PORTO MIXER — PARTS & OPERATION MANUAL — REV. #0 (08/08/03) — PAGE 5 P ARTS ORDERING PR OCEDURES When ordering parts, please supply the following information: ❒ ❒ ❒ ❒ ❒ Dealer account number ❒ ❒ ❒ ❒ ❒ Dealer name and address ❒ ❒ ❒ ❒ ❒ Shipping address (if different than billing address) ❒ ❒ ❒ ❒ ? ...

  • Stow SMC3PE - page 6

    P A GE 6 —ST O W POR T O MIXER — P ARTS & OPERA TION MANUAL — REV . #0 (08/08/03) Accidental Starting AL W A YS place the circuit breaker or power ON/OFF switch in the OFF position when the pump is not in use. Respiratory Hazard AL W A YS wear approved respir ator y protection. Equipment Damage Messages Other important messages are provid ...

  • Stow SMC3PE - page 7

    STOW PORTO MIXER — PARTS & OPERATION MANUAL — REV. #0 (08/08/03) — PAGE 7 ST O W PORT O MIXER— SAFETY MESSA GE ALER T SYMBOLS Accidental Starting AL W A YS place the engine ON/OFF switch in the OFF position, and remove the ignition key when the machine is not in use. Respiratory Hazard AL W A YS wear approv ed respirator y protection. E ...

  • Stow SMC3PE - page 8

    P A GE 8 —ST O W POR T O MIXER — P ARTS & OPERA TION MANUAL — REV . #0 (08/08/03) RULES FOR SAFE OPERA TION ■ AL W A YS refuel in a well-ventilated area, a wa y from spar k s and open flames. ■ AL W A YS use extreme caution when working with flammable liquids. When refueling, stop the engine and allow it to cool. DO NOT smoke around o ...

  • Stow SMC3PE - page 9

    STOW PORTO MIXER — PARTS & OPERATION MANUAL — REV. #0 (08/08/03) — PAGE 9 ■ High T emperatures – Alwa ys stop engine and allow the engine to cool before adding fuel, oil or performing service and maintenance functions. Contact with hot components can cause serious burns. ■ NEVER disconnect any "emergency or safety devices" ...

  • Stow SMC3PE - page 10

    P A GE 10 —ST O W PORT O MIXER — P ARTS & OPERA TION MANU AL — REV . #0 (08/08/03) Emergencies ■ AL W A YS know the location of the nearest fire extinguisher . ■ AL W A YS know the location of the nearest first aid kit . ■ In emergencies always know the location of the nearest phone or keep a phone on the job site . Also know the ph ...

  • Stow SMC3PE - page 11

    STOW PORTO MIXER — PARTS & OPERATION MANUAL — REV. #0 (08/08/03) — PAGE 11 OPERA TION AND SAFETY DECALS Machine Safety Decals The ST O W POR T O MIXER is equipped with a number of saf ety decals. These decals are provided for oper ator saf ety and maintenance inf or mation. The illustration below and on the ne xt page shows these decals a ...

  • Stow SMC3PE - page 12

    P A GE 12 —ST O W PORT O MIXER — P ARTS & OPERA TION MANU AL — REV . #0 (08/08/03) OPERA TION AND SAFETY DECALS 6. check V-belt before starting mixer . AL WA YS 1. Read owner’s manual before operating mixer. ELECTRIC MOTOR Make sure power cord has been disconnected from power source before cleaning mixer . use an extension cord of prope ...

  • Stow SMC3PE - page 13

    STOW PORTO MIXER — PARTS & OPERATION MANUAL — REV. #0 (08/08/03) — PAGE 13 ST O W PORT O MIXER— SPECIFICA TIONS ) r o t o M c i r t c e l E & e n i g n E ( s n o i t a c i f i c e p S . 1 e l b a T r o t o M c i r t c e l E / e n i g n E l e d o M0 0 2 1 9 N O T T A R T S & S G G I R B4 0 3 E Y L 7 1 R O D L A B e p y T e l g n ...

  • Stow SMC3PE - page 14

    P A GE 14 —ST O W PORT O MIXER — P ARTS & OPERA TION MANU AL — REV . #0 (08/08/03) ST O W PORT O MIXER— DIMENSIONS (MIXER) Figure 1. Mix N' Go Mixer Dimensions ...

  • Stow SMC3PE - page 15

    STOW PORTO MIXER — PARTS & OPERATION MANUAL — REV. #0 (08/08/03) — PAGE 15 ST O W POR T O MIXER— DIMENSIONS (ELECTRIC MO T OR) Figure 2. Electric Motor ...

  • Stow SMC3PE - page 16

    P A GE 16 —ST O W PORT O MIXER — P ARTS & OPERA TION MANU AL — REV . #0 (08/08/03) ST O W PORT O MIXER— GENERAL INFORMA TION APPLICA TION This mixer is only intended for the production of concrete and mor tar . The mixer m ust be used f or its intended purposes and is not suitable for the mixing of flammable or explosive substances. The ...

  • Stow SMC3PE - page 17

    STOW PORTO MIXER — PARTS & OPERATION MANUAL — REV. #0 (08/08/03) — PAGE 17 ST O W POR T O MIXER— MIXER COMPONENTS Figure 4. Mixer Components S T N I H G N I X I M . 3 e l b a T S N O I T A C I L P P A X I M S O I T A R S E I T I T N A U Q H C T A B H C T A B . X O R P P A T U P T U O . s b l 2 1 1 T N E M E C ) . s g K 0 5 ( g a B D N A ...

  • Stow SMC3PE - page 18

    P A GE 18 —ST O W PORT O MIXER — P ARTS & OPERA TION MANU AL — REV . #0 (08/08/03) Figure 5. Engine Controls and Components INITIAL SER VICING The engine (Figure 5) must be checked for proper lubrication and filled with fuel prior to operation. Refer to the manufacturers engine manual f or instructions and details of operation and ser vic ...

  • Stow SMC3PE - page 19

    STOW PORTO MIXER — PARTS & OPERATION MANUAL — REV. #0 (08/08/03) — PAGE 19 ST O W PORT O MIXER— ASSEMBL Y INSTRUCTIONS Assembly 1 . Remove the mixer drum and associated components from the packing container (Figure 6). Match the components against the parts list to make sure that they are all accounted fo r. Figure 6. Packing Container ...

  • Stow SMC3PE - page 20

    P A GE 20 —ST O W PORT O MIXER — P ARTS & OPERA TION MANU AL — REV . #0 (08/08/03) 6 . Tip mixer onto mouth as shown in Figure 10, and insert support stand into frame swivel point. 9 . Bef ore attempting to lift mix er , locate the fr ame locking clip . Attach the locking clip as sho wn in Figure 12. This will pre vent the mixing drum fro ...

  • Stow SMC3PE - page 21

    STOW PORTO MIXER — PARTS & OPERATION MANUAL — REV. #0 (08/08/03) — PAGE 21 ST O W PORT O MIXER— PRE-INSPECTION (GASOLINE ENGINE) Figure 15. Engine Oil Dipstick (Removal) 3 . Insert and remove the dipstick without screwing it into the filler neck. Check the oil level shown on the dipstick. 4 . If the oil level is low (Figure 16), fill to ...

  • Stow SMC3PE - page 22

    P A GE 22 —ST O W PORT O MIXER — P ARTS & OPERA TION MANU AL — REV . #0 (08/08/03) ST O W PORT O MIXER— INITIAL ST ART -UP (ELECTRIC MO T OR) CAUTION: CAUTION: CAUTION: CAUTION: CAUTION: DO NOT attempt to operate the mixer until the Saf ety , General Inf or mation and Inspection sections have been read and understood. Initial Start-up I ...

  • Stow SMC3PE - page 23

    STOW PORTO MIXER — PARTS & OPERATION MANUAL — REV. #0 (08/08/03) — PAGE 23 ST O W PORT O MIXER— INITIAL ST ART -UP (GASOLINE ENGINE) Star ting the Engine ( BRIGGS & STRA TT ON ) 1 . Place the choke lever (Figure 21) in the CHOKE (CLOSED) position if star ting a cold engine. DO NOT attempt to operate the mixer until the Saf ety , Gen ...

  • Stow SMC3PE - page 24

    P A GE 24 —ST O W PORT O MIXER — P ARTS & OPERA TION MANU AL — REV . #0 (08/08/03) ST O W PORT O MIXER— INITIAL ST ART -UP (GASOLINE ENGINE) Figure 26. Throttle Lever (Idle P osition) 2 . After the engine cools , mov e the throttle le v er to the ST OP position (Figure 27). Figure 27. Throttle Le ver (Stop P osition) Stopping The Engine ...

  • Stow SMC3PE - page 25

    STOW PORTO MIXER — PARTS & OPERATION MANUAL — REV. #0 (08/08/03) — PAGE 25 ST O W PORT O MIXER— MAINTENANCE Maintenance Gearbox Oil Check 1. P osition the mix er on a le vel surf ace and place a suppor t bloc k under the front of the mix er frame as shown in Figure 29. This will le v el the mixer . 2. NEVER! check the gearbox oil level ...

  • Stow SMC3PE - page 26

    P A GE 26 —ST O W PORT O MIXER — P ARTS & OPERA TION MANU AL — REV . #0 (08/08/03) ST O W PORT O MIXER— MAINTENANCE (GASOLINE ENGINE) Reference manufacturer engine manual for specific servicing instructions. NOTE e l u d e h c S e c n a n e t n i a M e n i g n E . 6 e l b a T ) 3 ( N O I T P I R C S E DN O I T A R E P OE R O F E B T S R ...

  • Stow SMC3PE - page 27

    STOW PORTO MIXER — PARTS & OPERATION MANUAL — REV. #0 (08/08/03) — PAGE 27 Maintenance P erf orm the scheduled maintenance procedures as definded by T able 6 and below: D AIL Y ■ Thoroughly remove dirt and oil from the engine and control area. Clean or replace the air cleaner elements as necessar y . Check and retighten all f asteners a ...

  • Stow SMC3PE - page 28

    P A GE 28 —ST O W PORT O MIXER — P ARTS & OPERA TION MANU AL — REV . #0 (08/08/03) ST O W PORT O MIXER— PREP ARA TION FOR LONG -TERM ST ORA GE Mixer Storage For storage of the mixer for over 30 days, the following is recommended: z Drain the fuel tank completely , or add ST A-BIL to the fuel. z Run the engine until the fuel is completel ...

  • Stow SMC3PE - page 29

    STOW PORTO MIXER — PARTS & OPERATION MANUAL — REV. #0 (08/08/03) — PAGE 29 NO TE P A GE ...

  • Stow SMC3PE - page 30

    P A GE 30 —ST O W PORT O MIXER — P ARTS & OPERA TION MANU AL — REV . #0 (08/08/03) ST O W PORT O MIXER— TR OUBLESHOO TING (ENGINE) G N I T O O H S E L B U O R T E N I G N E . 7 E L B A T M O T P M Y S M E L B O R P E L B I S S O P N O I T U L O S t r a t s o t t l u c i f f i D g u l p k r a p s t u b e l b a l i a v a s i l e u F e l b ...

  • Stow SMC3PE - page 31

    STOW PORTO MIXER — PARTS & OPERATION MANUAL — REV. #0 (08/08/03) — PAGE 31 ST O W PORT O MIXER— TROUBLESHOO TING (ENGINE/MIXER) G N I T O O H S E L B U O R T R E X I M . 8 E L B A T M O T P M Y S M E L B O R P E L B I S S O P N O I T U L O S . h g u o r s e t a t o r m u r D ? x o b r a e g e v i t c e f e D s a e c a l p e R . n r o w ...

  • Stow SMC3PE - page 32

    P A GE 32 —ST O W PORT O MIXER — P ARTS & OPERA TION MANU AL — REV . #0 (08/08/03) How to read the marks and remarks used in this parts book. Items Found In the “Remarks” Column Serial Numbers-Where indicated, this indicates a serial number range (inclusiv e) where a par ticular par t is used. Model Number-Where indicated, this shows ...

  • Stow SMC3PE - page 33

    STOW PORTO MIXER — PARTS & OPERATION MANUAL — REV. #0 (08/08/03) — PAGE 33 ST O W PORT O MIXER — SUGGESTED SP ARE P ARTS ST O W PORT O MIXER 1 TO 3 UNITS 1 to 3 Units Qt y . P/ N Description 2 ............ DM1840 ................ V -BEL T , A23 (ELECTRIC MO T OR) 2 ............ MS-01 ................... V -BEL T , A24 (GASOLINE) ...

  • Stow SMC3PE - page 34

    P A GE 34 —ST O W PORT O MIXER — P ARTS & OPERA TION MANU AL — REV . #0 (08/08/03) ST O W PORT O MIXER — NAME PLA TE AND DECALS NAME PLA TE AND DECALS ...

  • Stow SMC3PE - page 35

    STOW PORTO MIXER — PARTS & OPERATION MANUAL — REV. #0 (08/08/03) — PAGE 35 ST O W PORT O MIXER — NAME PLA TE AND DECALS NAME PLA TE AND DECALS NAMEPLA TE AND DECALS. NO P AR T NO P AR T NAME QTY . REMARKS 1 DCL300 DECAL: W ARNING ST O W 1 2 DECAL: ST O W POR T O MIX ..................... 1 ............ INCLUDED WITH TUB 3 DECAL: NAMEPLA ...

  • Stow SMC3PE - page 36

    P A GE 36 —ST O W PORT O MIXER — P ARTS & OPERA TION MANU AL — REV . #0 (08/08/03) MIXER ASSY . (PLASTIC DR UM) ST O W PORT O MIXER — MIXER ASSY . (PLASTIC DR UM) ...

  • Stow SMC3PE - page 37

    STOW PORTO MIXER — PARTS & OPERATION MANUAL — REV. #0 (08/08/03) — PAGE 37 ST O W PORT O MIXER — MIXER ASSY . (PLASTIC DR UM) MIXER ASSY . (PLASTIC DR UM) NO . P AR T NO . P AR T NAME QTY . REMARKS 1 # DM3150 HEX HEAD BOL T M12 x 70 1 2 # DM1356 OIL FILLER PLUG M14 x 2 x 15L 1 3 # DM1912 HEX NUT M10 2 4 # DM355 HEX HEAD BOL T M8 x P1.25 ...

  • Stow SMC3PE - page 38

    P A GE 38 —ST O W PORT O MIXER — P ARTS & OPERA TION MANU AL — REV . #0 (08/08/03) MIXER ASSY . (PLASTIC DR UM) ST O W PORT O MIXER — MIXER ASSY . (PLASTIC DR UM) ...

  • Stow SMC3PE - page 39

    STOW PORTO MIXER — PARTS & OPERATION MANUAL — REV. #0 (08/08/03) — PAGE 39 MIXER ASSY . (PLASTIC DR UM) NO . P AR T NO . P AR T NAME QTY . REMARKS 3 1 DM1527 HEX NUT M10 1 2 3 2 DM1524 B O L T 1 2 3 3 DM1510 PLASTIC BARREL 1 3 4 DM1531 BLADE, BARREL 2 3 5 DM1613 HANDLE GRIP , RUBBER 2 3 6 DM1630 TOP C O VER CLAMP 2 3 7 DM1631 SCREW 5.5 x ...

  • Stow SMC3PE - page 40

    P A GE 40 —ST O W PORT O MIXER — P ARTS & OPERA TION MANU AL — REV . #0 (08/08/03) TERMS AND CONDITIONS OF SALE — P AR TS Effective: July 15, 2003 T erms and Conditions of Sale STOW Construction Equipment ST O W CONSTR UCTION EQUIPMENT POST OFFICE BO X 6254 CARSON, CALIFORNIA 90749 310-661-4242 • 877-BUY -STO W F AX: 310-604-9237 E-MA ...

  • Stow SMC3PE - page 41

    STOW PORTO MIXER — PARTS & OPERATION MANUAL — REV. #0 (08/08/03) — PAGE 41 NO TE P A GE ...

  • Stow SMC3PE - page 42

    P AR TS AND OPERA TION MANUAL HERE'S HOW TO GET HELP PLEASE HA VE THE MODEL AND SERIAL NUMBER ON-HAND WHEN CALLING P AR TS DEP AR TMENT 800-427-1244 or 310-537-3700 F AX: 800-672-7877 or 310-637-3284 SER VICE DEP ARTMENT 800-478-1244 F AX: 310- 537-4259 TECHNICAL ASSIST ANCE 800-478-1244 F AX: 310- 631-5032 W ARRANTY DEP ARTMENT 888-661-4279, ...

Fabricant Stow Catégorie Webcam

Les documents que nous recevons du fabricant de l'appareilStow SMC3PE peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Stow
- manuels d’utilisations SMC3PE
- fiches produit Stow
- dépliants
- ou étiquettes-énergie Stow SMC3PE
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Stow SMC3PE.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Stow SMC3PE, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Stow SMC3PE. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Stow SMC3PE.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Stow SMC3PE, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Stow SMC3PE par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Stow SMC3PE.

Le manuel d’utilisation complet Stow, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Stow SMC3PE - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Stow SMC3PE, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lStow SMC3PE qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Stow SMC3PE - qui devraient nous aider dans les premières étapes lors de l'utilisation Stow SMC3PE
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Stow SMC3PE
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Stow SMC3PE dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Stow SMC3PE?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Stow SMC3PE, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Stow SMC3PE il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)