Français dropdown-ico

Manuel d’utilisation Generac MAX-12CV-X

30 pages 0.92 mb
Télécharger

Aller à la page of 30

Summary
  • Generac MAX-12CV-X - page 1

    It is of vital importance, before attempting to operate your engine, to read the general 'SAFETY INSTRUCTIONS AND W ARNINGS' section on pages 2-5 of this booklet and to strictly adhere to the advice contained therein. Also, please study the entire contents of this instruction manual, so as to familiarize yourself with the controls and oth ...

  • Generac MAX-12CV-X - page 2

    IF THE ENGINE F AILS T O ST ART FINAL ADJUSTMENT CARBURETTOR CLEANLINESS CARE AND MAINTENANCE EXPLODED VIEW & ENGINE P ARTS LIST CARBURETOR EXPLODED VIEW & P ARTS LIST O.S. GENUINE P ARTS & ACCESSORIES THREE VIEW DRA WING CONTENTS SAFETY INSTRUCTIONS AND W ARNINGS ABOUT YOUR O.S. ENGINE INTRODUCTION, BASIC ENGINE P ARTS INST ALLA TION A ...

  • Generac MAX-12CV-X - page 3

    Remember that your engine is not a "toy", but a highly efficient internal- combustion machine whose power is capable of harming you, or others, if it is misused. As owner , you, alone, are responsible for the safe operation of your engine, so act with discretion and care at all times. If at some future date, your O.S. engine is acquired b ...

  • Generac MAX-12CV-X - page 4

    W ARNINGS Model engine fuel is poi- sonous. Do not allow it to come into contact with the eyes or mouth. Always store it in a clearly marked container and out of the reach of children. Model engine fuel is also highly flammable. Keep it away from open flame, excessive heat, sources of sparks, or anything else which might ignite it. Do not smoke or ...

  • Generac MAX-12CV-X - page 5

    This engine is intended for model cars. Do not attempt to use it for any other purpose. Mount the engine in your model securely , following the manufacturers' recommendations, using appropriate screws and locknuts. Fit an effective silencer (muf fler). Frequent close exposure to a noisy exhaust (especially in the case of the most powerful high ...

  • Generac MAX-12CV-X - page 6

    NOTES To stop the engine, fully retard the throttle stick and trim lever on the trans-mitter, or, in an emergency, cut off the fuel supply by pinching the fuel delivery tube from the tank. • Warning! Immediately after a glowplug- ignition engine has been run and is still warm, conditions sometimes exist whereby it is just possible for the engine ...

  • Generac MAX-12CV-X - page 7

    INSTALLING THE GLOWPLUG Carburetor NOTE: With this engine, the piston will feel tight at the top of its stroke when the engine is cold. This is normal. The piston and cylinder are designed to achieve a perfect running clearance when they reach their normal running temperatures. Fit washer to glowplug and insert carefully into cylinder- head, making ...

  • Generac MAX-12CV-X - page 8

    ENGINE INST ALLA TION Make sure that the vehicle's engine mounting surfaces are level and in the same plane. Poor installation may cause distortion of the crankcase, bearings, etc., resulting in erratic running and loss of performance. The recommended screws for securing the engine are 3mm or 4-40 steel Allen hexagon socket type. If existing h ...

  • Generac MAX-12CV-X - page 9

    ー8ー This is a heavy-duty wet type air cleaner that has been developed specifically for the O.S. MAX-CV series model car engines. It contains specially impregnated filter elements which prevent highly damaging dust and dirt from being drawn into the engine through the carburetor, yet allow engine performance to be maintained for longer period ...

  • Generac MAX-12CV-X - page 10

    Always remove contaminated elements carefully, to ensure that dirt cannot enter the carburettor. Position the air cleaner correctly, so that it does not foul the cylinder-head or obstruct the needle-valve. • AIR CLEANER ELEMENTS • • Lower Filter Element Upper Filter Element Insert beneath flanges. Replacement elements are already impregnated ...

  • Generac MAX-12CV-X - page 11

    Glowplug life Particularly in the case of very high performance engines, glowplugs must be regarded as expendable Install a plug suitable for the engine. Use fuel containing a moderate percentage of nitromethane unless more is essential for racing events. Do not run the engine too lean and do not leave the battery connected while adjusting the need ...

  • Generac MAX-12CV-X - page 12

    Apart from when actually burned out, a plug may need to be replaced because it no longer delivers its best performance, such as when: When to replace the glowplug Filament surface has roughened and turned white. Filament coil has become distorted. Foreign matter has adhered to filament or plug body has corroded. Engine tends to cut out when idling. ...

  • Generac MAX-12CV-X - page 13

    LONG SOCKET WRENCH SILICONE TUBING Heatproof silicone tube of approx. 5mm o.d. and 2mm i.d. is required for the connection between the fuel tank and engine. FUEL BOTTLE OR PUMP ELECTRIC ST ARTER AND ST ARTER BA TTER Y Use an electric starter with 12-volt battery for starting the MAX-12CV . CARBURETOR CONTROLS ( 10C ) The Needle-Valve: The Mixture C ...

  • Generac MAX-12CV-X - page 14

    CARBURETOR CONTROLS ( 10E-R ) The Needle-Valve: The Mixture Control Screw: The Throttle Stop Screw: Three adjustable controls are provided on this carburetor. For adjusting the mixture strength when the throttle is fully open. For adjusting the mixture strength at part- throttle and idling speeds, to obtain steady idling and smooth acceleration to ...

  • Generac MAX-12CV-X - page 15

    approx 1mm Approx. 0.3-0.5mm The following procedure is suitable for these engines when the O.S. T-1020 tuned silencer and a fuel containing up to 30% nitromethane are used. Use the same fuel as is to be employed for all initial running and containing NOT LESS THAN 18% lubricant. T emporarily remove the glowplug to check that it glows bright red wh ...

  • Generac MAX-12CV-X - page 16

    30º When the engine starts, first allow it to operate in short runs at the very rich starting settings, with the glowplug battery still connected and with its driving wheels clear of the ground.The rich mixture will, under these conditions, provide adequate lubrication and cooling, indicated by profuse smoke from the exhaust. Next, disconnect the ...

  • Generac MAX-12CV-X - page 17

    IF THE ENGINE F AILS TO ST ART Check the following: Glowplug battery discharged or glowplug defunct. Fuel not reaching carburetor. Engine flooded. Do not over-prime. (This could also cause hydraulic lock and damage the engine on application of the electric starter.) Remove glowplug, close needle-valve and apply starter to pump out surplus fuel. At ...

  • Generac MAX-12CV-X - page 18

    In this case, turn the Mixture Control Valve clockwise 45~90˚. If, on the other hand, the engine tends to speed up momentarily and then cut out abruptly when the throttle is opened,the idling mixture is too lean. Correct this by turning the Mixture Control Valve counter-clockwise 45~90˚. Warning! NOTE: Mixture Control Valve adjustment should be m ...

  • Generac MAX-12CV-X - page 19

    BALL LINK AND SLIDE VALVE EXTENSION It is seldom necessary to separate the slide-valve extension from the slide-valve itself. For cleaning, withdraw this complete sub-assembly from the carburetor body after removing the slide-valve guide screw. Then wash with methanol or glow-fuel. (Note: take care not to lose the guide screw;it is a special one.) ...

  • Generac MAX-12CV-X - page 20

    4. CARE AND MAINTENANCE 1. 2. 3. The minute particles of foreign matter, that are present in any fuel may, by accumulating and partially obstructing fuel flow, cause engine performance to become erratic and unreliable. O.S. 'Super-Filters' (large and small) are available, as optional extras, to deal with this problem. One of these filters ...

  • Generac MAX-12CV-X - page 21

    MAX-12CV EXPLODED VIEW Type of screw C … Cap Screw M … Oval Fillister-Head Screw F … Flat Head Screw N … Round Head Screw S … Set Screw ✽ 1 2 3 4 5 6 7 8 9 0 - = q w e r t C.M2.6x12 C.M2.6x7 20 ...

  • Generac MAX-12CV-X - page 22

    MAX-12CV ENGINE P ARTS LIST The specifications are subject to alteration for improvement without notice. e w q = - 0 9 8 7 6 5 4 3 2 1 7 2403 120 7 2403 210 2 1407 000 2 1214 000 2 1202 010 2 1230 000 7 2403 200 7 1605 300 2 1213 000 2 1401 000 2 2631 019 2 1408 000 2 0810 007 2 1481 700 2 1481 020 2 1286 000 2 1205 040 2 1206 000 2 1203 011 2 1404 ...

  • Generac MAX-12CV-X - page 23

    MAX-12CV -X EXPLODED VIEW Type of screw C … Cap Screw M … Oval Fillister-Head Screw F … Flat Head Screw N … Round Head Screw S … Set Screw ✽ 1 2 3 4 5 6 7 8 9 0 - = q w e r t C.M2.6x12 M.M2.6x7 y u u -1 u -2 M.M2.6x7 22 ...

  • Generac MAX-12CV-X - page 24

    MAX-12CV -X ENGINE P ARTS LIST The specifications are subject to alteration for improvement without notice. e w q = - 0 9 8 7 6 5 4 3 2 1 7 2403 120 7 2403 210 2 1421 200 2 1214 000 2 1202 000 2 1230 000 7 2403 200 7 1605 300 2 1401 000 2 2631 019 2 1408 000 2 0810 007 2 1481 700 2 1481 020 2 1286 000 2 1205 040 2 1206 000 2 1203 011 2 1404 300 r t ...

  • Generac MAX-12CV-X - page 25

    The specifications are subject to alteration for improvement without notice. Type of screw C … Cap Screw M … Oval Fillister-Head Screw F … Flat Head Screw N … Round Head Screw S … Set Screw ✽ 10C CARBURETOR EXPLODED VIEW & P ARTS LIST No. Carburettor Rubber Gasket Ball Link No.4 Dust Cover Metering Needle Assembly Slide Valve Slide ...

  • Generac MAX-12CV-X - page 26

    The specifications are subject to alteration for improvement without notice. 10E-R CARBURETOR EXPLODED VIEW & P ARTS LIST 2 1481 950 2 7881 820 2 1481 900 2 2681 310 2 1481 120 2 1283 961 2 4881 824 2 1283 962 2 2481 506 2 1481 200 2 1283 210 2 2681 419 2 1481 420 2 1481 600 - 0 -1 0 9 8 7 6 5 4 3 2 1 7 -1 7 -2 0 -2 2 2615 000 No. Carburetor Ru ...

  • Generac MAX-12CV-X - page 27

    ■ RACING ENGINE PARTS (71608001) (71605300) (71605100) ■ (72103110) (72103120) ■ (72103020) ■ (72103310) ■ (71530100) ■ (71521000) ■ (72403202) ■ (72403120) (72103130) (72103140) O.S. GENUINE PARTS & ACCESSORIES O.S. Glow Plug Exhaust Header Pipes For Kyosho Super10 For Kyosho Spider & HPI Nitro For Tamiya TG10 For Tamiya TG ...

  • Generac MAX-12CV-X - page 28

    ■ Displacement ■ Bore ■ Stroke ■ Practical R.P.M. ■ Power output ■ Weight SPECIFICATIONS 12CV,12CV-X THREE VIEW DRAWING Dimensions(mm) 2.11 cc(0.129cu.in.) 14.0 mm(0.551in.) 13.7 mm(0.539in.) 3,000 ~ 30,000 r.p.m. 0.56 bhp / 29,000 r.p.m. 211g(7.45oz.)12CV 269g(9.50oz.)12CV-X 190g(6.70oz)12CV Hyper 248g(8.75oz)12CV-X Hyper 25 39 40 40 4 ...

  • Generac MAX-12CV-X - page 29

    MEMO 28 ...

  • Generac MAX-12CV-X - page 30

    C Copyright 2000 by O.S.Engines Mfg. Co., Ltd. All rights reserved. Printed in Japan. 120104 T E L. (06) 6702-0225 F AX. (06) 6704-2722 6-15 3-Chome Imagawa Higashisumiyoshi-ku Osaka 546-0003, Japan URL : http://www .os-engines.co.jp U N E Q U A L L E D Q U A L I T Y P R E C I S I O N & P E R F O R M A N C E E S T A B L I S H I N G T H E S T A ...

Fabricant Generac Catégorie Automobile Parts

Les documents que nous recevons du fabricant de l'appareilGenerac MAX-12CV-X peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Generac
- manuels d’utilisations MAX-12CV-X
- fiches produit Generac
- dépliants
- ou étiquettes-énergie Generac MAX-12CV-X
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Generac MAX-12CV-X.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Generac MAX-12CV-X, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Generac MAX-12CV-X. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Generac MAX-12CV-X.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Generac MAX-12CV-X, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Generac MAX-12CV-X par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Generac MAX-12CV-X.

Le manuel d’utilisation complet Generac, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Generac MAX-12CV-X - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Generac MAX-12CV-X, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lGenerac MAX-12CV-X qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Generac MAX-12CV-X - qui devraient nous aider dans les premières étapes lors de l'utilisation Generac MAX-12CV-X
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Generac MAX-12CV-X
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Generac MAX-12CV-X dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Generac MAX-12CV-X?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Generac MAX-12CV-X, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Generac MAX-12CV-X il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)