Français dropdown-ico

Manuel d’utilisation Vermont Casting DBT33

34 pages 5.41 mb
Télécharger

Aller à la page of 34

Summary
  • Vermont Casting DBT33 - page 1

    INST ALLER: DO NOT DISCARD THIS MANUAL - LEA VE FOR HOMEOWNER 10002789 08/00 Rev . 0 I NST ALLA TION I NSTRUCTIONS & H OMEOWNER ' S M ANUAL DO NOT ST ORE OR USE GASOLINE OR OTHER FLAMMABLE V APOURS AND/OR LIQUIDS IN THE VICINITY OF THIS OR ANY OTHER APPLIANCE. FOR YOUR SAFETY WHA T T O DO IF YOU SMELL GAS: * Do not try to light any applian ...

  • Vermont Casting DBT33 - page 2

    DBT33/DBT36/DBT39 -2- 10002789/0 T ABLE O F C ONTENTS Please Read The Installation & Operating Instructions Car efully Befor e Using The Appliance. Important: Read all the instructions and warnings carefully befor e starting the installation. Failur e to follow these instructions fully may result in a possible r e hazard and will void the ma ...

  • Vermont Casting DBT33 - page 3

    10002789/0 -3- DBT33/DBT36/DBT39 This gas replace should be installed by a qualied installer in accordance with local building codes and with current CAN /CGA-B149 (. 1 or .2) Installation codes for Gas Burning Fireplaces and Equipment. FOR U.S.A Installations follow local codes and/or the current National Fuel Gas Code. ANSI Z223.1. FOR SAFE ...

  • Vermont Casting DBT33 - page 4

    DBT33/DBT36/DBT39 -4- 10002789/0 A PPLIANCE D IMENSIONS Appliance Dimensions Ref. DBT33 DBT36 DBT39 A 838 mm (33") 914 mm (36") 991 mm (39") B 733 mm (28.87") 870 mm (34.25") 870 mm (34.25") C 416 mm (16.37") 533 mm (21") 533 mm (21") D 787 mm (31") 838 mm (33") 914 mm (36") E 559 mm (22&q ...

  • Vermont Casting DBT33 - page 5

    10002789/0 -5- DBT33/DBT36/DBT39 C LEARANCE TO C OMBUSTIBLES Appliance T op ............................. 0 mm (0") Bottom ....................... 0 mm (0") Side ............................ 0 mm (0") Back ........................... 0 mm (0") V enting Concentric sections of DV V ent T op, bottom & sides .. 25 mm (1") M ...

  • Vermont Casting DBT33 - page 6

    DBT33/DBT36/DBT39 -6- 10002789/0 F INAL F INISHING Non-combustible materials such as brick or tile may be extended over the edges of the face of the appliance. DO NOT cover any vent or grille panels. If a T rim Kit is going to be installed on the replace, the brick or tile will have to be installed ush with the edges of the appliance. G AS S ...

  • Vermont Casting DBT33 - page 7

    10002789/0 -7- DBT33/DBT36/DBT39 G AS L INE I NST ALLA TION When purging the gas lines, the front glass must be removed. The gas pipeline can be brought in through the rear of the replace as well as the bottom. Knockouts are provided on the bottom behind the valve to allow for the gas pipe installation and testing of any gas connection. It is mo ...

  • Vermont Casting DBT33 - page 8

    DBT33/DBT36/DBT39 -8- 10002789/0 C ONVER TING T HE A PPLIANCE F ROM LP TO N A TU RAL G AS OR N A TURAL G AS T O LP . The DBT33 is convertible between Natural Gas an LP gas (and vice-versa) with the use of a conversion kit purchased seperately , see your dealer for the correct part number . The DBT36 & 39 can only be converted from Propane to Na ...

  • Vermont Casting DBT33 - page 9

    10002789/0 -9- DBT33/DBT36/DBT39 A = clearance above grade, veranda, por ch, deck, or bal- cony [* 12 inches (305mm) minimum] B = clearance to window or door that may be opened [12" (306mm)]. C = clearance to permanently closed window [minimum 12 inches (305mm) r ecommended to pr event condensation on window] D = vertical clearance to ventilat ...

  • Vermont Casting DBT33 - page 10

    DBT33/DBT36/DBT39 -10- 10002789/0 Fig. 1 1 Fig. 12 Fig. 13 Fig. 14 Fig. 15 ...

  • Vermont Casting DBT33 - page 11

    10002789/0 -1 1- DBT33/DBT36/DBT39 H OW T O U SE T HE V ENT G RAPH The vent chart should be read in conjunction with the follow- ing vent installation instructions to determin the relationship of the vertical and horizontal dimensions of the vent system 1. Determine the height of the centre of the horizontal vent pipe exiting through the outer wall ...

  • Vermont Casting DBT33 - page 12

    DBT33/DBT36/DBT39 -12- 10002789/0 V E R T ICA L S IDE W ALL A PP LIC A TIO NS Since it is very important that the venting system maintain its balance between the combustion air intake and the ue gas exhaust, certain limita- tions as to vent congurations apply and must be strictly adhered to. The V ent Graph showing the relationship between ve ...

  • Vermont Casting DBT33 - page 13

    10002789/0 -13- DBT33/DBT36/DBT39 V ER TICAL S IDEW ALL I NST ALLA TIONS STEP 1 Locate vent opening on the wall. It may be necessary to rst position the replace and measure to obtain hole location. Depending on whether the wall is combustible or non-combus- tible, cut opening to size. (Fig. 22) (For combustible walls rst frame in opening. ...

  • Vermont Casting DBT33 - page 14

    DBT33/DBT36/DBT39 -14- 10002789/0 STEP 6 Use appropriate length of pipe sections - telescopic or xed - and install the horizontal vent sections. The sections which go through the wall are packaged with the starter kit, and can be cut to suit if necessary . (Fig. 26). Sealing vent pipe and restop gaps with high temperature sealant will restric ...

  • Vermont Casting DBT33 - page 15

    10002789/0 -15- DBT33/DBT36/DBT39 DO NOT BACK FILL AROUND SNORKEL. A CLEARANCE OF A T LEAST 4” MUST BE MAINT AINED BETWEEN THE SNORKEL AND THE SOIL If the foundation is recessed, use recess brackets (not supplied) for securing lower portion of the snorkel. Fasten brackets to wall rst and then secure to snorkel with self-drilling #8 x 1/2 sheet ...

  • Vermont Casting DBT33 - page 16

    DBT33/DBT36/DBT39 -16- 10002789/0 • 7DVCS must be used to support offsets. (Fig. 36)This application will require that you rst determine the roof pitch and use the appropriate starter kit. (See V enting Components List) • The minimum height of the vent above the highest point of penetration through the roof is 2'. See Fig. 38. V ER TICA ...

  • Vermont Casting DBT33 - page 17

    10002789/0 -17- DBT33/DBT36/DBT39 V ER TICAL T HROUGH -T HE -R OOF I NST ALLA TION 1. Locate your replace. 2. Plumb to centre of the (4") ue collar from ceiling above and mark position. 3. Cut opening equal to 9-3/8" x 9-3/8" (240 mm x 240 mm). 4. Proceed to plumb for additional openings through the roof. In all cases, the open ...

  • Vermont Casting DBT33 - page 18

    DBT33/DBT36/DBT39 -18- 10002789/0 C RIMPED E ND V ENTING C OMPONENTS Starter Kit -Model 7DVSK - Sidewall V enting Starter Kit - Model 7TDVSKV - V ertical V enting for 7TDVSKV -A order 1/12 to 6/12 roof pitch for 7TDVSKV -B order 7/12 to 12/12 roof pitch for 7TDVSKV -F order at roof Starter Kit - Model 7DVSKS -Snorkel Kit for Below Grade Installa ...

  • Vermont Casting DBT33 - page 19

    10002789/0 -19- DBT33/DBT36/DBT39 T WIST L OCK V ENTING C OMPONENTS Starter Kit -Model 7TDVSK - Sidewall V enting Starter Kit - Model 7TDVSKV - V ertical V enting for 7TDVSKV -A order 1/12 to 6/12 roof pitch for 7TDVSKV -B order 7/12 to 12/12 roof pitch for 7TDVSKV -F order at roof Starter Kit - Model 7TDVSKS -Snorkel Kit for Below Grade Install ...

  • Vermont Casting DBT33 - page 20

    DBT33/DBT36/DBT39 -20- 10002789/0 G ENERAL O PERA TING I NSTRUCTIONS G LASS I NFORMA TION Only glass approved by CFM Majestic Inc. should be used on this replace. • The use of any non-approved replacement glass will void all product warranties. • Care must be taken to avoid breakage of the glass. • Under no circumstances should this applia ...

  • Vermont Casting DBT33 - page 21

    10002789/0 -21- DBT33/DBT36/DBT39 I NST ALLA TION OF L OGS & L A V A R OCK Refer to the log identication chart to identify specic log numbers. 1. Remove the front glass / frame assembly . 2. Remove the logs from their packaging. The logs are fragile and should be handled with care. Keep the packaging material out of the reach of children ...

  • Vermont Casting DBT33 - page 22

    DBT33/DBT36/DBT39 -22- 10002789/0 F LAME & T EMPERA TURE A DJUSTMENT RN/RP & EN/EP Models For units equipped with ‘HI/LO’ valves the ame adjustment is accomplished by rotating the ‘HI/LO’ adjustment knob located near the centre of the gas control valve, Fig. 44 & 45 F LAME C HARACTERISTICS It is important to periodically perf ...

  • Vermont Casting DBT33 - page 23

    10002789/0 -23- DBT33/DBT36/DBT39 LIGHTING INSTRUCTIONS 3. Open control access panel. 4. Push in gas control knob slightly and turn clock- wise to "OFF". Do not force. 5. Close control access panel. 10. Push the control knob all the way in and hold. Immediately light the pilot by repeatedly depress- ing the piezo spark ignitor until a  ...

  • Vermont Casting DBT33 - page 24

    DBT33/DBT36/DBT39 -24- 10002789/0 TROUBLE SHOOTING THE GAS CONTROL SYSTEM HONEYWELL MILLIVOL T V AL VE ...

  • Vermont Casting DBT33 - page 25

    10002789/0 -25- DBT33/DBT36/DBT39 TROUBLE SHOOTING THE GAS CONTROL SYSTEM SIT NOV A 820 MILLIVOL T V AL VE Note: Before trouble shooting the gas control system, be sure external gas shut off is in the "On" position. W ARNING: BEFORE DOING ANY GAS CONTROL SER VICE WORK, REMOVE GLASS FRONT . SYMPTOM POSSIBLE CAUSES CORRECTIVE ACTION 1. Spar ...

  • Vermont Casting DBT33 - page 26

    DBT33/DBT36/DBT39 -26- 10002789/0 R EPLACEMENT P AR TS L IST Items marked ‘*’ ar e not shown in the following parts pictorial page. Ref. Description DBT33 DBT36 DBT39 1 Log Set (complete) 10000470 10000023 10000024 1a Log - Front left BA2 BB6 BC5 1b Log - Front right BA3 BB7 BC6 1c Log - rear BA4 BB8 BC7 1d Log - T op left BA5 BB9 BC8 1e Log - ...

  • Vermont Casting DBT33 - page 27

    10002789/0 -27- DBT33/DBT36/DBT39 Ref. Description DBT33 DBT36 DBT39 * Knob, fan speed control, (FK24 option) 51882 51882 51882 17 Fan assembly , with bracket (FK12 option) ZA11 10 ZA11 10 ZA1 1 10 18 W indow frame assembly 10001803 10001425 54363 * W indow glass (with gasket) 10002822 10001781 10002821 * Gasket (window glass) 57317 57317 57317 19 ...

  • Vermont Casting DBT33 - page 28

    DBT33/DBT36/DBT39 -28- 10002789/0 P AR TS P ICT ORIAL ...

  • Vermont Casting DBT33 - page 29

    10002789/0 -29- DBT33/DBT36/DBT39 O PTIONAL A CCESSORIES A V AILABLE EB-1 E LECTRICAL B OX The EB-1 Electrical junction box when tted and correctly wired gives an easy and convenient power outlet for the optioal fan kit. If the EB-1 electrical junction box is being tted the replace must be electrically connected and grounded in accordance ...

  • Vermont Casting DBT33 - page 30

    DBT33/DBT36/DBT39 -30- 10002789/0 W IRING I NSTRUCTIONS The replace, when installed, must be electri- cally connected and grounded in accordance with local codes or , in the absence of local codes, with the current CSA C22.1 Canadian Electric Code. For U.S.A. installations follow the local codes and the national electrical code ANSI/NFP A No 70. ...

  • Vermont Casting DBT33 - page 31

    10002789/0 -31- DBT33/DBT36/DBT39 C ERAMIC R EFRACTOR Y K ITS Ceramic refractory panels are available in kit form for the DBT series appliances. Appliance Model Kit Name DBT33 33BDVTCR DBT36 36BDVCR DBT39 39BDVCR T ake care when handling the refractory panels as they are fragile until held in place and sup- ported. Installation, refer to Figs. 52 & ...

  • Vermont Casting DBT33 - page 32

    DBT33/DBT36/DBT39 -32- 10002789/0 D ECORA TIVE B A Y W INDOWS Bay window kits are available for the DBT33, DBT36 & DBT39 model appliances. When tting the Bay W indow Kits the original front frame/glass assembly MUST remain in place. The Bay W indow kit is tted over the existing front glass. Installation 1. Remove the upper and lower brass ...

  • Vermont Casting DBT33 - page 33

    10002789/0 -33- DBT33/DBT36/DBT39 ...

  • Vermont Casting DBT33 - page 34

    DBT33/DBT36/DBT39 -34- 10002789/0 410 Admiral Blvd. • Mississauga, Ontario , Canada L5T 2N6 • 905-670-7885 www .vermontcastings.com CFM Majestic, Inc. © Copyright CFM Majestic, Inc. BASIC W ARRANTY : The CFM Majestic, Inc.™ (hereinafter referred to collectively as the "Compan y") warrants that your new Vermont Castings Gas Applianc ...

Fabricant Vermont Casting Catégorie Indoor Fireplace

Les documents que nous recevons du fabricant de l'appareilVermont Casting DBT33 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Vermont Casting
- manuels d’utilisations DBT33
- fiches produit Vermont Casting
- dépliants
- ou étiquettes-énergie Vermont Casting DBT33
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Vermont Casting DBT33.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Vermont Casting DBT33, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Vermont Casting DBT33. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Vermont Casting DBT33.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Vermont Casting DBT33, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Vermont Casting DBT33 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Vermont Casting DBT33.

Le manuel d’utilisation complet Vermont Casting, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Vermont Casting DBT33 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Vermont Casting DBT33, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lVermont Casting DBT33 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Vermont Casting DBT33 - qui devraient nous aider dans les premières étapes lors de l'utilisation Vermont Casting DBT33
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Vermont Casting DBT33
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Vermont Casting DBT33 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Vermont Casting DBT33?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Vermont Casting DBT33, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Vermont Casting DBT33 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)