-
Hunter Fan M3535-01 - page 1
www .HunterF an.com 1.888.830.1326 PA G E 13 Light Kit PA G E 12 Blades T able of C ontents Operation, Maintenanc e & Cleaning PA G E 17 T roubleshooting ? ? ? PA G E 19 PA G E 5 Ceiling Br acket PA G E 4 Mounting Options 30 inches 7 feet PA G E 2 What to Expect with Y our Installation Ladder PA G E 3 T ools Needed Congratulations on purchasing ...
-
Hunter Fan M3535-01 - page 2
www .HunterF an.com 1.888.830.1326 M3535-01 • 06/18/13 • © Hunter F an Company 1.888.830.1326 1.888.830.1326 What t o Expec t with Y our Installation Know your wiring If you are unfamiliar with wiring, use a qualied electrician. Y ou may need a friend to help you. Check box to see fan weight Assess location 30 inches from blade tip to neare ...
-
Hunter Fan M3535-01 - page 3
www .HunterF an.com 1.888.830.1326 T ools Needed Ladder Po wer Drill (optional) 9/64” Drill Bit (optional) Screwdrivers Pliers Wire Strippers If mounting to a support structure, you will also need these tools . 3 M3535-01 • 06/18/13 • © Hunter F an Company ...
-
Hunter Fan M3535-01 - page 4
www .HunterF an.com 1.888.830.1326 4 M3535-01 • 06/18/13 • © Hunter F an Company 1.866.268.1936 If you ha ve an angled ceiling: 1. Y ou will need a longer do wnrod (sold separately) . 2. If your ceiling angle is greater than 34°, y ou will also need an Angled Mounting Kit (sold separately) . Guide T ouches BOTH Ceiling & Wa ll S I T U A T ...
-
Hunter Fan M3535-01 - page 5
www .HunterF an.com 1.888.830.1326 C eiling Bracket 5 Refer to warning w .1 on pg. 2 T o av oid possible elec trical shock, before installing your fan, disconnect the power by turning off the circuit breakers to the outlet box associated with the wall switch location. F or angled ceilings, point opening toward peak. If you are unable to do this, ca ...
-
Hunter Fan M3535-01 - page 6
www .HunterF an.com 1.888.830.1326 Assembling the T op Housing KEEP! Remove the pre-installed setscrew so that the downrod can be inserted. K E E P ! Install three upper motor co ver screws, f ound in the hardware bag , and tighten them securely . Upper Motor Cov er Screw T o assemble the housing t o the hanger adapter , align the three raised tabs ...
-
Hunter Fan M3535-01 - page 7
www .HunterF an.com 1.888.830.1326 7 M3535-01 • 06/18/13 • © Hunter F an Company 1.888.830.1326 Downrod Slid e Slid e 1 2 3 4 5 6 7 8 9 10 skip to next page If you need a diff erent downrod length follo w these steps: Steps 1-5 to remo ve standard downrod pipe Steps 6-10 to reassemble with new pipe www .HunterF an.com Sold Separately Longer Do ...
-
Hunter Fan M3535-01 - page 8
www .HunterF an.com 1.888.830.1326 Downrod (c ontinued) 8” 3/8” If the setscrew is not tightened securely , the fan may fall. 1.888.830.1326 www .HunterF an.com 8” 3/8” C U T & S T R I P (not to scale) The wires can be cut, but lea ve at least 8” extending from the top of the downrod . Tighten the setscrew with pliers. DO NO T HAND TI ...
-
Hunter Fan M3535-01 - page 9
1.888.830.1326 9 M3535-01 • 06/18/13 • © Hunter F an Company www .HunterF an.com Downrod (c ontinued) DO NO T PICK THE F AN UP BY THE CANOPY OR WIRES. Place the downrod ball into the slot in the ceiling bracket. Put the wires and do wnrod through the canopy . Let the canop y sit loosely on top of the fan. ...
-
Hunter Fan M3535-01 - page 10
www .HunterF an.com 1.888.830.1326 Wiring T urn the splices upward and push them carefully back through the hanger bracket into the outlet box. Spread the wires apart, with the grounded wires on one side of the outlet box and the ungrounded wires on the other side of the outlet bo x. Refer to CA UTION c.1 on pg. 2 10 M3535-01 • 06/18/13 • © Hu ...
-
Hunter Fan M3535-01 - page 11
www .HunterF an.com 1.888.830.1326 11 M3535-01 • 06/18/13 • © Hunter F an Company Canop y Lift the canopy into place so that the screw holes are aligned . Position the canop y so that, when lifted into place , the canopy ts into the hanging bracket as shown. Insert the two canopy screws found in the hardwar e bag. No te: Fan style may vary ...
-
Hunter Fan M3535-01 - page 12
www .HunterF an.com 1.888.830.1326 Blades Y our blades ar e shielded with Dust Armor® which is a nanotechnology coating that repels dust. F or cleaning the fan, use soft brushes or cloths to prevent scratching . Cleaning agents ma y damage the nishes. Attach the blade to the motor using the at washers from the hardware bag and blade assembly ...
-
Hunter Fan M3535-01 - page 13
www .HunterF an.com 1.888.830.1326 Light Kit Align the keyholes in the light k it with the two partially installed screws and turn the light k it clockwise until the screws are in the narrow ends of the keyholes. Thread the 9-pin plug connector from the fan through the light kit. Attachment Screw Partially install two attachment screws, f ound in t ...
-
Hunter Fan M3535-01 - page 14
www .HunterF an.com 1.888.830.1326 14 M3535-01 • 06/18/13 • © Hunter F an Company Light Kit (c ontinued) Make sure the light kit is securely attached to the mounting plate. F ailure to properly secure all thr ee assembly screws could result in the light xture falling. Connect the upper 9-pin plug connector from the fan to the lower 9-pin pl ...
-
Hunter Fan M3535-01 - page 15
www .HunterF an.com 1.888.830.1326 15 M3535-01 • 06/18/13 • © Hunter F an Company Light Kit (c ontinued) Connect the 4 pin plug from the ballast to the uorescent bulb. 4 Pin Plug C ONGRA TULA TIONS! Y OU’RE DONE! See next page for fan opera tion instruc tions. Glass Globe T rim Ring Globe Assembly Screw Place the glass globe into the glob ...
-
Hunter Fan M3535-01 - page 16
www .HunterF an.com 1.888.830.1326 Remote C ontrol ON T urn P ow er Note: The remote must be pair ed before the fan will operate. Within 3 minutes of rest oring power to the fan, press both the F an Off button and the High button for at least 4 seconds . Y our fan will turn on low to indicate successful syncing. If it does not, turn off po wer to y ...
-
Hunter Fan M3535-01 - page 17
www .HunterF an.com 1.888.830.1326 Rocker- Style Plate Switch C over Plate Removed T abs T o install the tr ansmitter cradle, remov e the two screws holding the switch c over plate. Do not remov e the cover plate. Orient the cr adle by lining up the two mounting holes with those on the cov er plate. Inser t and tighten the screws. Do not ov er tigh ...
-
Hunter Fan M3535-01 - page 18
www .HunterF an.com 1.888.830.1326 18 M3535-01 • 06/18/13 • © Hunter F an Company Opera tion, Maintenance , & Cleaning (con tinued) When cleaning the fan, use soft brushes or cloths to prevent scr atching. Cleaning products may damage the nishes. Safe-Exit • Press the F an Off button for at least thr ee seconds to initiate the Safe-Ex ...
-
Hunter Fan M3535-01 - page 19
www .HunterF an.com 1.888.830.1326 M3535-01 • 06/18/13 • © Hunter F an Company 19 T roubleshooting Exc essive wobbling • Tighten all of the blade and blade iron screws until they are snug . • Use the provided balancing kit and instruc tions to balance the fan. Noisy Operation • Tighten the blade and blade iron screws until they are snug ...
Avez-vous une question à propos de Hunter Fan M3535-01?
Utiliser le formulaire ci-dessous
Si vous n’avez pas résolu votre problème avec Hunter Fan M3535-01, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Hunter Fan M3535-01 il est probable qu’il a envie de partager la façon de le résoudre.