Français dropdown-ico

Manuel d’utilisation Snapper Coronet RE 200

36 pages 6.87 mb
Télécharger

Aller à la page of 36

Summary
  • Snapper Coronet RE 200 - page 1

    OPERA T OR’S MANU AL Cor onet / 2400 / RE 200 Series 13HP Hydro Rider s Mfg. No. Description 1694610 Coronet, 13HP 1694612 Coronet, 13HP (CE) 1694613 2413H, 13HP 1694614 2413H, 13HP (CE) 1694615 RE1330, 13HP 1694616 RE1330, 13HP (CE) 1695508 Coronet, 13HP 1695509 RE1330, 13HP 2690244 Coronet, 13HP & 30” Mower 2690246 Coronet, 13HP & 30? ...

  • Snapper Coronet RE 200 - page 2

    THIS P A GE INTENTIONALL Y BLANK (FOR PLA CEMENT ONL Y - DO NO T PRINT) 2 ...

  • Snapper Coronet RE 200 - page 3

    3 T able of Contents T roubleshooting, Adjustments & Service .......25 Troubleshooting the Rider .....................................25 Troubleshooting the Mower ..................................26 Seat Adjustment ....................................................27 Steering Gear Adjustment .....................................27 Steering W ...

  • Snapper Coronet RE 200 - page 4

    4 Safety Rules & Information Operating Safety Congratulations on purchasing a superior-quality piece of lawn and garden equipment. Our products are designed and manufactured to meet or exceed all industry standards for safety. Power equipment is only as safe as the operator. If it is misused, or not properly maintained, it can be dangerous! Rem ...

  • Snapper Coronet RE 200 - page 5

    5 Safety Rules and Information Slope Operation You could be seriously injured or even killed if you use this unit on too steep an incline. Using the unit on a slope that is too steep or where you don’t have adequate traction can cause you to lose control or roll over. A good rule of thumb is to not operate on any slope you cannot back up (in 2-wh ...

  • Snapper Coronet RE 200 - page 6

    6 Safety Rules & Information GENERAL OPERA TION 1. Read, understand, and follow all instructions in the manual and on the unit before starting. 2. Do not put hands or feet near rotating parts or under the machine. Keep clear of the discharge opening at all times. 3. Only allow responsible adults, who are familiar with the instructions, to opera ...

  • Snapper Coronet RE 200 - page 7

    7 Safety Rules and Information CHILDREN Tragic accidents can occur if the operator is not alert to the presence of children. Children are often attracted to the unit and the mowing activity. Never assume that children will remain where you last saw them. 1. Keep children out of the mowing area and under the watchful care of another responsible adul ...

  • Snapper Coronet RE 200 - page 8

    8 Safety Rules & Information SER VICE AND MAINTENANCE Safe Handling of Gasoline 1. Extinguish all cigarettes, cigars, pipes, and other sources of ignition. 2. Use only approved gasoline containers. 3. Never remove the gas cap or add fuel with the engine running. Allow the engine to cool before refueling. 4. Never fuel the machine indoors. 5. Ne ...

  • Snapper Coronet RE 200 - page 9

    9 Identification Numbers Tractor ID Tag ENGINE REFERENCE DATA Model Description Name/Number Unit MFG Number PRODUCT REFERENCE DATA Unit SERIAL Number Dealer Name Date Purchased Engine Make Engine Type/Spec Engine Model Engine Code/Serial Number Mower Deck MFG Number Mower Deck SERIAL Number When contacting your authorized dealer for replace- ment p ...

  • Snapper Coronet RE 200 - page 10

    10 Safety Decals SAFETY DECALS This unit has been designed and manufactured to pro- vide you with the safety and reliability you would expect from an industry leader in outdoor power equipment manufacturing. Although reading this manual and the safety instructions it contains will provide you with the necessary basic knowledge to operate this equip ...

  • Snapper Coronet RE 200 - page 11

    11 Safety Icons Warning: Read Operator’s Manual. Read and understand the Operator’s Manual before using this machine. Danger: Thrown Objects. This machine is capable of throwing objects and debris. Keep bystanders away. Warning: Remove Key Before Servicing. Remove the key and consult techni- cal literature before performing repairs or maintenan ...

  • Snapper Coronet RE 200 - page 12

    12 Features & Controls + - Throttle/Choke Contr ol (Single Lever Models) The throttle/choke lever controls engine speed and choke. Move the throttle forward to increase engine speed and back to decrease engine speed. Always operate at FULL throttle. Move the control fully forward (past the detent) to close the choke. Close the choke for cold st ...

  • Snapper Coronet RE 200 - page 13

    13 Features & Controls Fuel T ank To remove the cap, turn counterclockwise. PT O Switch The PTO (Power Take-Off) switch engages and disen- gages attachments that use the PTO. To engage the PTO, pull UP on the switch. Push DOWN to disengage. Note that the operator must be seated firmly in the trac- tor seat for the PTO to function. T ransmission ...

  • Snapper Coronet RE 200 - page 14

    14 Operating the Rider GENERAL OPERA TING SAFETY Be sure to read all information in the SAFETY RULES AND INFORMATION section before attempting to oper- ate this unit. Become familiar with all of the controls and how to stop the unit. CHECKS BEFORE ST AR TING • Check that crankcase is filled to full mark on dipstick. See the Engine Manual for inst ...

  • Snapper Coronet RE 200 - page 15

    15 Operating the Rider BRAKE PED AL OPERA TION 1. See Figure 2. Depressing the pedal from position A to B disengages the transmission drive and also returns the transmission control lever to neutral (from forward speeds). Fully depressing the pedal to position B applies the rider brake. 2. See Figure 2. P ark ing brake is applied at pedal posi- tio ...

  • Snapper Coronet RE 200 - page 16

    16 Operating the Rider SELECTING GR OUND & ENGINE SPEED Ground speed is selected by releasing the clutch/brake pedal (D, Figure 4) and moving the control lever (C, Figure 4) to the appropriate speed selection. If the ter- rain is rough, hilly or sloping, use first or second gear. If the grass is wet or over 3” (76 mm) high, use full engine sp ...

  • Snapper Coronet RE 200 - page 17

    PUSHING THE RIDER BY HAND 1. Disengage the PTO and turn the engine off. 2. Push the transmission release (A, Figure 6) in and push down to lock into released position. 3. The tractor can now be pushed by hand. Figure 5. Mower Belt Pattern A. PTO Pulley D. Front Idler Pulley (30”) B. Arbor Pulley (30”) Left Arbor Pulley (34”) Right Arbor Pulle ...

  • Snapper Coronet RE 200 - page 18

    MO WER REMO V AL AND INST ALLA TION NOTE: Perform mower installation on a hard, level sur- face such as a concrete floor. For easier mower removal and installation, rear trailing arms (F, Figure 7) can be removed by removing spring clips and clevis pins. 1. Park rider and turn off PTO switch and engine, remove the key and apply parking brake. Turn ...

  • Snapper Coronet RE 200 - page 19

    19 Operating the Rider ST ORA GE Before you store your unit for the off-season, read the “Maintenance and Storage” instructions in the SAFETY RULES AND INFORMATION section, then perform the following steps: • Disengage the PTO, set the parking brake, & remove the key. • Perform engine maintenance and storage measures listed in the Engin ...

  • Snapper Coronet RE 200 - page 20

    20 Regular Maintenance MAINTENANCE SCHEDULE & PR OCEDURES The following schedule should be followed for normal care of your rider and mower. * Refer to engine owner’s manual. Change original engine oil after initial break-in period. ** More often in hot (over 85° F: 30° C) weather or dusty operating conditions. *** Service after the first 5 ...

  • Snapper Coronet RE 200 - page 21

    Figure 10. Engine Compartment A. Fuel Tank B. Ignition Switch C. Battery D. Throttle / Choke Cable E. PTO Switch (Electric Clutch) F. Air Filter G. Oil Fill / Dipstick H. Fuel Filter I. Oil Drain 21 Regular Maintenance RAISING THE SEA T DECK To gain access to the engine compartment, simply tilt the seat deck forward. ADDING FUEL To add fuel: 1. Rem ...

  • Snapper Coronet RE 200 - page 22

    22 Regular Maintenance *2397 LUBRICA TION Lubricate the rider and mower as shown in Figures 11 - 16. When a grease gun is shown, wipe the fitting clean, apply two or three shots of lithium base automotive grease, and wipe off excess grease. When an oil can is shown, wipe the area clean, apply a few drops of oil (SAE 30), then wipe up drips or spill ...

  • Snapper Coronet RE 200 - page 23

    23 Figure 17. Battery A. Negative Battery Terminal & Cable B. Positive Battery Terminal & Cable C. Hold Down Strap B A TTER Y MAINTENANCE Cleaning the Battery and Cables Service Interval: Every 100 Hours 1. Disconnect the cables from the battery, negative cable first (A, Figure 17). 2. Remove the battery hold-down (C) and battery. 3. Clean ...

  • Snapper Coronet RE 200 - page 24

    24 SER VICING THE MO WER BLADES 1. Remove mower from the rider. 2. Blades should be sharp and free of nicks and dents. If not, sharpen blades as described in following steps. 3. To remove blade for sharpening, use wooden block to hold blade while removing the blade mounting cap- screw (Figure 19). 4. Use a file to sharpen blade to fine edge. Remove ...

  • Snapper Coronet RE 200 - page 25

    25 T roubleshooting Adjustments & Service TR OUBLESHOO TING While normal care and regular maintenance will extend the life of your equipment, prolonged or constant use may eventually require that service be performed to allow it to continue operating properly. The troubleshooting guide below lists the most common problems, their causes and reme ...

  • Snapper Coronet RE 200 - page 26

    26 T roubleshooting, Adjustments & Service T roub leshooting the Rider (Continued) PROBLEM CAUSE REMEDY Engine runs, but rider will not drive. 1. Ground speed control lever in 1. Shift in forward or reverse. neutral. 2. Transmission release lever in 2. Move into drive position. “push” position. 3. Belt is broken. 3. See “Drive Belt Replac ...

  • Snapper Coronet RE 200 - page 27

    27 T roubleshooting, Adjustments & Service W ARNING To avoid serious injury, perform adjustments only with engine stopped, key removed and rider on level ground. Figure 23. Steering Gear Adjustment A. Capscrews *2401 Capscrews Figure 24. Steering Wheel Height Adjustment A. Steering Shaft SEA T ADJUSTMENT Use the lever on the front of the seat ( ...

  • Snapper Coronet RE 200 - page 28

    28 BRAKE ADJUSTMENT Brake Adjustment 1. Release the parking brake. 2. Brake arm (C, Figure 25) should be touching stop (B). 3. Remove cotter pin (D) and loosen the castle nut (A). Place a 0.015” feeler gauge (E) gap between the brake disc (F) and the brake puck (G). a. To decrease gap, insert feeler gauge in gap and turn nut (A) clockwise until r ...

  • Snapper Coronet RE 200 - page 29

    29 *2397 Figure 26. Trailing Arms A. Spacers C. Nut B. Rear Mower Rollers D. Rear Trailing Arms MO WER ADJUSTMENTS If the cut is uneven, the mower may need leveling. Unequal or improper tire pressure may also cause an uneven cut. Make sure tire pressure is correct as speci- fied in Checking Tire Pressure. To achieve proper mower levelling, perform ...

  • Snapper Coronet RE 200 - page 30

    30 Figure 29. Front-To-Back Levelling A. Adjustment Nut D. Levelling Rod B. Rear Nut E. Jam Nut C. Bracket *2397 Front-T o-Back Le veling 1. Make sure mower is level side-to-side and that rear rollers are on the ground. 2. Position blade(s) front-to-back. Measure the distance from the ground to front tip of blade(s), and from ground to rear tip of ...

  • Snapper Coronet RE 200 - page 31

    31 T ransport Height Adjustment Transport height should be adjusted so that rear mower rollers are 1/8” - 1/4” (3-6 mm) above ground when mower lift lever is in transport position. To adjust, per- form both mower leveling procedures first, then do the following procedure. See Figure 30. 1. Park rider on a flat level surface. 2. Adjust Dial-A-Cu ...

  • Snapper Coronet RE 200 - page 32

    32 Figure 32. Mower Belt Replacement - 34” A. Idler Pulley Arm D. Capscrews B. Idler Pulley E. Arbor Cover C. PTO Pulley RIDER DRIVE BEL T REPLA CEMENT Replacement of the rider drive belt requires removal of the transmission and carrier frame. Should the drive belt ever fail, contact your dealer for replacement. MO WER BEL T REPLA CEMENT - 30” ...

  • Snapper Coronet RE 200 - page 33

    33 Specifications ENGINE 13 HP* Intek OHV — Briggs & Stratton Horsepower 13 HP @ 3400 rpm Displacement 21 Cu. In. (344 cc) Electrical 12 Volt, 3 Amp D.C. Battery 230 CCA Air Cleaner Pre-Cleaned Air to Paper Filter Oil Capacity 3 Pints (1.42 L) 16 HP* Command™ — K ohler Horsepower 16 HP @ 3400 rpm Displacement 27.9 Cu. In. (460 cc) Electri ...

  • Snapper Coronet RE 200 - page 34

    Parts & Accessories REPLA CEMENT P ARTS Replacement parts are available from your authorized dealer. Always use genuine Simplicity/Snapper service Parts. TECHNICAL MANU ALS Additional copies of this manual are available, as well as fully illustrated parts lists. These manuals show all of the product’s components in exploded views (3D illustra ...

  • Snapper Coronet RE 200 - page 35

    35 ...

  • Snapper Coronet RE 200 - page 36

    Briggs & Stratton Power Products Group, L.L.C. Copyright © 2008 Briggs & Stratton Corporation Milwaukee, WI USA. All Rights Reserved www.BRIGGSandSTRATTON.com www.MasseyLawn.com www.snapper.com www.simplicitymfg.com ...

Fabricant Snapper Catégorie Lawn Mower

Les documents que nous recevons du fabricant de l'appareilSnapper Coronet RE 200 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Snapper
- manuels d’utilisations Coronet RE 200
- fiches produit Snapper
- dépliants
- ou étiquettes-énergie Snapper Coronet RE 200
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Snapper Coronet RE 200.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Snapper Coronet RE 200, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Snapper Coronet RE 200. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Snapper Coronet RE 200.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Snapper Coronet RE 200, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Snapper Coronet RE 200 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Snapper Coronet RE 200.

Le manuel d’utilisation complet Snapper, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Snapper Coronet RE 200 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Snapper Coronet RE 200, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lSnapper Coronet RE 200 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Snapper Coronet RE 200 - qui devraient nous aider dans les premières étapes lors de l'utilisation Snapper Coronet RE 200
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Snapper Coronet RE 200
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Snapper Coronet RE 200 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Snapper Coronet RE 200?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Snapper Coronet RE 200, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Snapper Coronet RE 200 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)