Manuel d’utilisation Ingersoll-Rand 7872-F

12 pages 0.91 mb
Télécharger

Aller à la page of 12

Summary
  • Ingersoll-Rand 7872-F - page 1

    Tool Products OPERATOR’S MANUAL INCLUDING: OPERATION, INSTALLATION & MAINTENANCE SECTION M10 MANUAL 58 Released: 5/79 Revised: 3-10-95 “2200” SERIES SHORT GRINDERS Models: 7870-F-( ), 7871-F-( ), 7872-F and 7873-F. Form: 1558-2 READ THIS MANUAL CAREFULLY BEFORE INSTALLING, OPERATING OR SERVICING THIS EQUIPMENT. FAILURE TO OBSERVE THE FOLL ...

  • Ingersoll-Rand 7872-F - page 2

    FAILURE TO OBSERVE THE FOLLOWING WARNINGS COULD RESULT IN INJURY. Turn off air supply and disconnect air supply hose before installing, removing or adjusting any accessory on this tool, or before performing any maintenance on this tool. Do not carry the tool by the hose. Do not overreach when operating this tool. Keep body stance balanced and firm. ...

  • Ingersoll-Rand 7872-F - page 3

    ROUTINE LUBRICATION REQUIREMENTS M10 58 Lack of or an excessive amount of lubrication will affect the perfor- mance and life of this tool. Use only recommended lubricants at below time intervals: EVERY 8 HOURS OF TOOL OPERATION - Fill lubricator reser- voir of recommended F.R.L. with spindle oil (29665). if an in line or air line lubricator is not ...

  • Ingersoll-Rand 7872-F - page 4

    MODEL IDENTIFICATION The grinder models listed in the model identification table above are furnished with collet assembly 41753-o as standard equipment and are intended for use with mounted Wheels and shall not be used with other type grinding wheels unless a proper wheel guard, recommended by the grinder manufacturer is attached to the grinder. Se ...

  • Ingersoll-Rand 7872-F - page 5

    GRINDING WHEEL MOUNTING INSTRUCTIONS M10 Disconnect air supply from grinder or shut off air supply and exhaust (drain) air line of compressed air before mounting or removing any abrasive wheel or wire brush, or otherwise performing maintenance or service to the tool. Check abrasive wheels prior to mounting for chips or cracks. Cracked or wheels sha ...

  • Ingersoll-Rand 7872-F - page 6

    DISASSEMBLY AND ASSEMBLY OF TOOLS Disconnect air supply from tool or shut off air supply and exhaust (drain) line of compressed air BEFORE performing maintenance or service to tool. Before starting to disassemble or assemble this tool (any part or completely), be sure to read “Inspection, Maintenance and Instal- lation” section, To minimize the ...

  • Ingersoll-Rand 7872-F - page 7

    TYPICAL CROSS SECTION OF TOOL Ml0 58 7 ...

  • Ingersoll-Rand 7872-F - page 8

    MOTOR SECTION DISASSEMBLY Remove motor assembly from housing as outlined on page 6. Remove retaining nut (33694). Grasp cylinder in one hand and tap threaded end of rotor with a soft face hammer; motor will come apart. ASSEMBLY NOTE: Pack bearings with ARO 33153 grease and coat i.d. of cyl- inder with ARO 29665 spindle oil upon assembly. Assemble t ...

  • Ingersoll-Rand 7872-F - page 9

    HEAD SECTION Ml0 DISASSEMBLY ASSEMBLY 58 Remove nut (36776) and valve components can be removed from head. Lubricate “0” ring (Y325-7) with ARO 38460 lubricant and as- semble to valve stem. Assemble valve stem, spring (32656), reg- ulator and seal (36781) to head and secure with nut (36776). NOTE: Align notch (or hole) in side of regulator with ...

  • Ingersoll-Rand 7872-F - page 10

    HEAD SECTION DISASSEMBLY Remove nut (36778) and valve components can be removed from head. To remove throttle button (36745), remove roll pin (Y178-212). ASSEMBLY Lubricate “0” ring (Y326-7) with ARO 36460 lubricant and as- semble to valve stem. Assemble valve stem, spring (32858), reg- ulator and seal (36781) to head and secure with nut (36776 ...

  • Ingersoll-Rand 7872-F - page 11

    ACCESSORIES 41753-( ) 3-PIECE COLLET ASSEMBLY COLLETNUT-41751 COLLET BODY - 41752 COLLET NUT DIA. - 3/4” COLLET BODY DIA. - 21/32” 3/8” - 24 THREAD 0VER ALL LENGTH - 2 1/4” 44127-( ) ERICKSON 3-PIECE COLLET ASSEMBLY M10 58 33226-( ) 3-PIECE COLLET ASSEMBLY COLLET NUT - 33220 COLLET BODY - 32218 COLLET NUT DIA. - 15/16” CUP RING - 33221 CO ...

  • Ingersoll-Rand 7872-F - page 12

    TROUBLE SHOOTING LISTED BELOW ARE SOME OF THE MOST COMMON CAUSES FOR THE GRINDER TO MALFUNCTION. MALFUNCTIONS BEYOND THE SCOPE OF THIS MANUAL SHOULD BE BROUGHT TO THE ATTENTION OF YOUR ARO REPRESENTATIVE OR RETURN THE TOOL TO THE FACTORY FOR REPAIR. CONDlTlON LOW SPEED AND POWER OR GRIND- ER WILL NOT RUN. THROTTLE VALVE HARD TO OPERATE. TOOL WILL N ...

Fabricant Ingersoll-Rand Catégorie Grinder

Les documents que nous recevons du fabricant de l'appareilIngersoll-Rand 7872-F peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Ingersoll-Rand
- manuels d’utilisations 7872-F
- fiches produit Ingersoll-Rand
- dépliants
- ou étiquettes-énergie Ingersoll-Rand 7872-F
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Ingersoll-Rand 7872-F.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Ingersoll-Rand 7872-F, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Ingersoll-Rand 7872-F. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Ingersoll-Rand 7872-F.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Ingersoll-Rand 7872-F, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Ingersoll-Rand 7872-F par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Ingersoll-Rand 7872-F.

Le manuel d’utilisation complet Ingersoll-Rand, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Ingersoll-Rand 7872-F - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Ingersoll-Rand 7872-F, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lIngersoll-Rand 7872-F qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Ingersoll-Rand 7872-F - qui devraient nous aider dans les premières étapes lors de l'utilisation Ingersoll-Rand 7872-F
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Ingersoll-Rand 7872-F
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Ingersoll-Rand 7872-F dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Ingersoll-Rand 7872-F?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Ingersoll-Rand 7872-F, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Ingersoll-Rand 7872-F il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Commentaires (0)