-
HANNspree F660-10A1 - page 1
2F , No.362, Ruei-guang Rd., Neihu District, T aipei City 1 14, T aiwan, R.O.C. TEL: 886-2-87520000 F AX: 886-2-87527092 www .hannspree.com F660-10A1 ...
-
HANNspree F660-10A1 - page 2
Table of Contents 1 1. Warranty and Service ................................................... 3 2. Preface .................................................................... ..... 4 3. Description of Warning Symbols ..................................... 5 4. Safety Notices .......................................................... ..... 6 5. Re ...
-
HANNspree F660-10A1 - page 3
Table of Contents 2 11. Adjusting On-Screen Display (OSD) Settings ............ ... 2 9 Brightness ............................................................ ... 3 0 Contrast ............................................................... ... 3 1 Video Setting ........................................................... 3 2 Hue ................... ...
-
HANNspree F660-10A1 - page 4
3 The instructions on this manual are for the model(s) listed on the front cover . Before you st art reading, check your product number by lookin g at the rear of your TV . Thank you for purchasing our Liquid Crystal Display T elevision (LCD TV). With this product, you will be able to enjoy superior audio and video while enriching your lifes tyle w ...
-
HANNspree F660-10A1 - page 5
4 This manual is designed to assist users in setting up and using the LCD TV . Information in this document has been carefully checked for accu- racy; however , no guarantee is given to the correctness of the co ntents. The information in this document is subject to change without notice. Copyright © Copyright 2003 Hannspree, Inc. All rights reser ...
-
HANNspree F660-10A1 - page 6
5 Electric Power Notice Electric power may cause personal inju ry and mechanical damage if it is misused. Although safety has been tak en into conside ration during the design and production of this product, electric shock or fire can result when the product is misused. T o prevent potential danger , follow the instructions below when installing, o ...
-
HANNspree F660-10A1 - page 7
6 Power Supply Safety Notes 1. T o avoid electric shocks, do not use an extend ed power cord or an outlet that does not match this pr oduct's plug or leaves the plug exposed. 2. This product has a 3-pin gro unded plug. The th ird pin connect s to ground; do not r emove it. 3. If the power cord or plug is damaged or worn, u nplug it immedi- ate ...
-
HANNspree F660-10A1 - page 8
7 Before Y ou Proceed 1. Read the Safety Notices and the User ’s Manual ca refully before turning the pro duct on. 2. Keep your User ’s Manual in a safe place for future reference. Keep the box and packaging in case the pr oduct needs to be shipped in the future. 3. Follow the product and warn ing label instructions. 4. Any changes or modificat ...
-
HANNspree F660-10A1 - page 9
8 Optimal V iewing Dist ance 102 cm 1 1 ...
-
HANNspree F660-10A1 - page 10
9 Import ant Safety Instructio ns 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water . 6. Clean only with a dr y cloth. 7. Do not block any ven t ilation openings. Insta ll in accordance with th e manufacturer’s instruct ions. 8. Do not instal l near an ...
-
HANNspree F660-10A1 - page 11
10 10. Protect the power cord from being walked on or pinched particularly at th e plug, conve- nience receptacles, and the point where they exit from the app aratus. 1 1. U se only with a cart, stand, tripod, bracket, or table specified by the manufa cturer , or sold with the apparatus. Whe n a cart is used, use caution when movi ng the cart/app a ...
-
HANNspree F660-10A1 - page 12
11 Personal Safety T o avoid overloading t he power supply , do not plug too many electrical devices into an outlet or extension cable. Dangerous high-volt age electric power compo - nents are lo cated inside the TV . T o avoid electric shock, do not disassemble the casing. Do not place or drop met als, small objects, or flammable materials in t he ...
-
HANNspree F660-10A1 - page 13
12 Installation T o avoid damage to power circuit s, do not place the TV in locations where there is excessive steam or dust. Do not place the TV on a bed, sofa, carpet, or in a sealed cabinet to avoid blocking the product's vent s. Install the outdoor antenna far from p ower trans- mission lines to av oid possible danger . Remove the power co ...
-
HANNspree F660-10A1 - page 14
13 Operation Maintenanc e This product is designed for power sources as labeled on the casing. Avoid using any other power accessories to avoid electric sho ck or other damage. The plug can be inserted into an outlet in only one direction. Notify a qualified service techni- cian if you cannot plug it in correctly . If there is any problem that cann ...
-
HANNspree F660-10A1 - page 15
14 FCC Compliance S tat ement 1 This device complies with part 15 of the FCC Rules. Operation is sub- ject to the following two conditions: (1) This device may not cause harm- ful interference, and ( 2) this devi ce must accept any interference received, including inter ference that may cause undesired operation . This equipment has been tested and ...
-
HANNspree F660-10A1 - page 16
15 DOC Compliance Notice 1 This digital app aratus does not exc eed the Class B limits for radio noise emissions from digital app aratus as set out in the Radio Inte rference Regulations of the Canadian Dep artment of Communications.This device complies with Canada ICES-003 Class B. CE Conformity S tat ement 2 This device complies with the requirem ...
-
HANNspree F660-10A1 - page 17
16 Thank you for purchasing this Liquid Crys- tal Display TV. Y our LCD TV is designed to be safe, versatile, and easy to use. The evening purse design makes it a fun addition to any room. Y ou can watch broadcast or cable televi- sion channels, and easily connect a VCR, VCD, or DVD player or a game device to the standard RCA and S-V ideo input por ...
-
HANNspree F660-10A1 - page 18
17 Make sure the following component s are included in the box. Cont act your vendor immediately if any thing is missing or damaged. TV User ’ s Manual Quick St art Guide W arranty and Service Manual Wire Material Package Power Cord Power Adapter 4-IN-1 Cable RCA Jack x 3 S Jack X 1 User's Manual Q uick Start G uide W a r ra n ty a n d s e r ...
-
HANNspree F660-10A1 - page 19
18 F r ont View Description Function 1 Menu T urns the On-Screen Display (OSD) menus on and of f. 2 Select channel Changes channels. Press CH to increase the channel number . Press CH to decrease the channel number . 3 Power T u rns the TV on and off. 4 Adjust volume Press VOL + to i ncreases the volume. Press VOL– to decr eases the volum ...
-
HANNspree F660-10A1 - page 20
19 Input and Output P or ts Description Function 1 ANT Connects to a n antenna or CA TV cable television line. 2 AV I n Connects to VCR/VCD/DVD player CVBS RCA cables or a game device. 3 HEADPHONE Connects to head phones or other audio device. 4 DC-IN Connects to the inclu ded power adapter . ANT A V In HEADPHONE DC-IN 12 3 4 ...
-
HANNspree F660-10A1 - page 21
20 Connecting to an Antenna or Cable TV 1 Connect one end of the UHF or CA TV cable to the ANT Jack (VHF/UHF IN Jack) on the back o f the TV . 2 Connect the other en d of the VHF/ UHF (Ante nna) or CA TV cable to the antenna socket or CA TV cable. Note If you cannot receive channels after connecting to an antenna or cable TV line, try scanning for ...
-
HANNspree F660-10A1 - page 22
21 Connecting to A V Devices Connect external devices such as a VCR, VCD or DVD playe r , or video game to the TV using the 4-IN-1 cable. Connecting to a V CR/VCD/DVD Player The illustration presented here shows how to connect the TV to a VCR and VCD or DVD player . Actual connections may vary accord- ing to the make and model of the device. Refer ...
-
HANNspree F660-10A1 - page 23
22 Connecting to a Video Camera The instructions presented here are a general guide to connecting the TV to a camcorder or other type of digita l camera. Actual connec- tions may vary according to the make and model of the device. Refer to the user’s manual included with th e camcorder or camera for more detailed instruction s. Note The cables ar ...
-
HANNspree F660-10A1 - page 24
23 Connecting to a Game Device The instructions presented here are a general guide to connecting the TV to a game device using t he RCA Jacks provided (some game devices may require a unique ada pter that is not provided). Actual connections may vary according to the make and model of the game device. Refer to the user’s manual included with the ...
-
HANNspree F660-10A1 - page 25
24 Connecting Exter nal Speak er s or Headphones External speakers or head phones may be used to listen to the TV rather than using the built-in speakers. Connect external speakers or headphones to the head phone line out port as illustrated. Notes • External speakers or head phones are not included with the product. • The internal TV speakers ...
-
HANNspree F660-10A1 - page 26
25 Connecting the P owe r Adapter 1 Connect the power cord to the power adapter as illustrated. 2 Plug the power adapter connector in to the DC-IN input jack on the rear panel of the TV . 3 Insert the three-pronged plug at the other end of the power cord into a powe r outlet. ANT A V In HEADPHONE DC-IN Power cord Power adapte r DC-IN Power outlet T ...
-
HANNspree F660-10A1 - page 27
26 Using the Remote Co ntrol For best results, use the remote control within a distance of 5 me ters from the front of the TV’ s signal sensor . Do not exceed an angle of 30 degrees when pointing at the signa l sensor . Refer to the following illustration. 30 30 5m 3m 3m 10 Using the TV ...
-
HANNspree F660-10A1 - page 28
27 T ur ning the TV On and Of f 1 Press the POWER button on the remote control (or control panel). The power LED changes from dark to green, indicating that the power has been turned on. 2 Press the POWER button again; the power LED changes from green to dark, indicating that the TV is in of f mode. Selecting Channels Press the CH and CH bu ...
-
HANNspree F660-10A1 - page 29
28 Switching Source Signals Press the SOURCE button on the remote control or control panel to select the incoming source signal. The current source setting (TV/CA TV , S-Video, or A V) appears on the top lef t corner of the screen. Note The TV supports S-V id eo input in addition to normal video and audio sig- nals. Adjusting the V olum e Press the ...
-
HANNspree F660-10A1 - page 30
29 The On-Screen Display (OSD) menu system provides a quick a nd simple method to adjust your TV’ s settings. This chapter describes how to change each of the available settin gs. The OSD can be used with either the remote contro l or the front con- trol panel. The following sections explain h ow to adjust settings in the OSD menus using the remo ...
-
HANNspree F660-10A1 - page 31
30 Brightness 1 Press MENU to enter the OSD menus. 2 Press the CH UP bu tton or the CH DOWN button to select Brightness. 3 Press MENU . The brightness slide bar appears. 4 Press the CH UP button to increase the brightness. 5 Press the CH DOWN button to decrease the brightne ss. 6 Press MENU to confirm the setting and return to the Main menu. ETO ET ...
-
HANNspree F660-10A1 - page 32
31 Contrast 1 Press MENU to enter the OSD menus. 2 Press the CH UP bu tton or the CH DOWN button to select Contrast. 3 Press MENU . The contrast slide bar appears. 4 Press the CH UP button to increase the contrast. 5 Press the CH DOWN button to decrease the contr ast. 6 Press MENU to confirm the setting and return to the Main menu. ETO ETO Main Men ...
-
HANNspree F660-10A1 - page 33
32 Video Setting Press the MENU butt on to enter the OSD menus. 1 Press the CH UP button or the CH DOWN button to select Video Settin g. 2 Press MENU t o enter the Video Settin g menu. MENU CH ETO ETO Main Menu Video Setting ENTER ...
-
HANNspree F660-10A1 - page 34
33 Hue 1 Press the CH UP bu tton or the CH DOWN button to select Hue. 2 Press MENU to enter the Hue menu. 3 Press the CH UP button to incr ease the hue towards the red spectrum. The image becomes more red. 4 Press the CH DOWN button to decrease the hue towards the green spectrum. The image becomes more green. 5 Press MENU to confirm the setting and ...
-
HANNspree F660-10A1 - page 35
34 Saturation 1 Press the CH UP bu tton or the CH DOWN button to selec t Saturation. 2 Press MENU to enter the Saturation menu. 3 Press the CH UP button to incr ease the saturation. The screen image becomes more vibrant. 4 Press the CH DOWN button to decrease the saturation. The screen image becomes less vibrant. 5 Press MENU to confirm the setting ...
-
HANNspree F660-10A1 - page 36
35 Sharpness 1 Press the CH UP bu tton or the CH DOWN button to select Sharpness. 2 Press MENU to enter the Sharpness menu. 3 Press the CH UP button to incr ease the sharpness. 4 Press the CH DOWN button to decrease the sharpn ess. 5 Press MENU again to confirm the setting and return to the V ideo Set - ting menu. Video Setting R G B ENTER Sharpnes ...
-
HANNspree F660-10A1 - page 37
36 Color T emperature 1 Press the CH UP bu tton or the CH DOWN button to select Color . 2 Press MENU to enter the Color menu. The following three color temperatures are available. St andard Color P r es s the CH UP button or th e CH DOWN b ut t o n to select S tandard, then press MENU . W arm Color P r es s the CH UP button or th e CH DOWN b u tt o ...
-
HANNspree F660-10A1 - page 38
37 Audio Setting Press the MENU butt on to enter the OSD menus. 1 Press the CH UP button or the CH DOWN button to select Audio Setting. 2 Press MENU t o enter the Audio Setting menu. MENU CH ETO ETO Main menu Audio Setting E N T E R ...
-
HANNspree F660-10A1 - page 39
38 Tr e b l e 1 Press the CH UP bu tton or the CH DOWN button to select T reble. 2 Press MENU to enter the T reble menu. 3 Press the CH UP button to incr ease the treble. 4 Press the CH DOWN button to decrease the treble. 5 Press MENU to confirm the setting and return to the Audio Setting menu. E N T E R A u d i o S e t t i n g Treble 48 Note The n ...
-
HANNspree F660-10A1 - page 40
39 Bass 1 Press the CH UP bu tton or the CH DOWN button to select Bass. 2 Press MENU to enter the Bass menu. 3 Press the CH UP button to incr ease the bass. 4 Press the CH DOWN button to decrease the bass. 5 Press MENU to confirm the setting and return to the Audio Setting menu. E N T E R A u d i o S e t t i n g 48 Bass Note The new setting is conf ...
-
HANNspree F660-10A1 - page 41
40 Balance 1 Press the CH UP bu tton or the CH DOWN button to select Balance. 2 Press MENU to enter the Balance menu. 3 Press the CH DOWN button to shift the balance to the left speaker . 4 Press the CH UP button to shif t the balance to the right speaker . 5 Press MENU to confirm the setting and return to the Audio Setting menu. E N T E R A u d i ...
-
HANNspree F660-10A1 - page 42
41 TV Setting Press the MENU butt on to enter the OSD menus. 1 Press the CH UP button or the CH DOWN button to select TV Setting. 2 Press MENU to e nter the TV Setting menu. MENU CH ETO ETO Main Menu TV Setting ENTER ...
-
HANNspree F660-10A1 - page 43
42 TV/CA TV 1 Press the CH UP bu tton or the CH DOWN button to select TV/CA TV . 2 Press MENU to enter the TV/CA TV menu. The following choices are available. Receiving Broadcast TV P r es s the CH UP button or th e CH DOWN b ut t o n to select TV , then press MENU . Receiving Cable TV P r es s the CH UP button or th e CH DOWN b u tt o n to select ...
-
HANNspree F660-10A1 - page 44
43 MTS 1 Press the CH UP bu tton or the CH DOWN button to select MTS. 2 Press MENU to enter the MTS menu. MAIN 1 Press the CH UP bu tton or the CH DOWN button to select MAIN (default). MAIN is highlig hted in red. 2 Press MENU again to confirm the selection. SAP 1 Press the CH UP bu tton or the CH DOWN button to select SAP . SAP is highlighted in r ...
-
HANNspree F660-10A1 - page 45
44 Auto Program 1 Press the CH UP bu tton or the CH DOWN button to select Auto Pro - gram. 2 Press MENU to enter the Auto Pro - gram menu. 3 Press the CH UP bu tton or the CH DOWN button to select Y es or No . 4 Press MENU . The screen goes blank and the chan- nel indicator values range from 2 to 69 (antenna connection) or from 1 to 125 (CA TV cabl ...
-
HANNspree F660-10A1 - page 46
45 Manual Program This function allows you to locate cha nnels for adding to or erasing from preset channels. 1 Press the CH UP bu tton or the CH DOWN button to select Manual Program. 2 Press MENU to enter the Manual Program menu. 3 Press the CH UP bu tton and CH DOWN button to find the channel you want to add. 4 When you have found the channel, pr ...
-
HANNspree F660-10A1 - page 47
46 Channel Add/Erase 1 Press the CH UP bu tton or the CH DOWN button to select CH. Add/Erase. 2 Press MENU to enter the CH. Add/Erase menu. Select one of the following options. Add Channel 1 Press the CH UP button to sele ct Add. 2 Press the MENU to add the selected channel. Erase Channel 1 Press the CH DOWN button to select Erase. 2 Press MENU to ...
-
HANNspree F660-10A1 - page 48
47 Miscellaneous Setting Press the MENU button to enter the OSD menus. 1 Press the CH UP button or the CH DOWN button to select Miscellaneous. 2 Press MENU to enter the Mis- cellaneous menu. MENU CH ETO Main Menu Miscellaneous ENTER ...
-
HANNspree F660-10A1 - page 49
48 OSD Position 1 Press the CH UP button or th e CH DOWN button to select OSD Position. 2 Press MENU to enter the OSD Position menu. The following options are available. Horizont al Position 1 Press the CH UP button or the CH DOWN button to select H - Position. 2 Press MENU . 3 Press the CH DOWN button to move the OSD screen to the left. Press the ...
-
HANNspree F660-10A1 - page 50
49 Language 1 Press the CH UP bu tton or the CH DOWN button to select Language. 2 Press MENU to enter the Language menu. The screen displays the available OSD languages: English and T -Chinese (T raditional Chinese). 3 Press the CH UP bu tton or the CH DOWN button to select a language. 4 Press MENU to confirm your choice. ENTER Miscellaneous O S D ...
-
HANNspree F660-10A1 - page 51
50 Sleep Timer The sleep timer turns the TV of f automatically after a set period of time. 1 Press the CH UP bu tton or the CH DOWN button to select Sleep. 2 Press MENU to enter the Sleep menu. 3 The screen displays the available sleep timer setting: –O f f – 30 minutes – 60 minutes – 90 minutes – 120 minutes 4 Press the CH UP bu tton or ...
-
HANNspree F660-10A1 - page 52
51 OSD Display This setting allows you to set whether info rmation such as the selected channel is shown on the T V screen when the DISPLA Y but- ton is pressed. 1 Press the CH UP bu tton or the CH DOWN button to select OSD Display . 2 Press MENU to enter the OSD Display menu. 3 Press the CH UP bu tton or the CH DOWN button to select On or Of f. 4 ...
-
HANNspree F660-10A1 - page 53
52 Reset The Reset function returns all of your TV’ s user settings to their fac- tory defaults. Wa r n i n g : The reset fun ction will erase all of your custom and favorite channel settings, and will reset all displa y settings (such as contras t, bright- ness, etc.) to the factory de fault values. The reset function cannot be reversed once it ...
-
HANNspree F660-10A1 - page 54
53 T urn the power off before you begin cleaning the TV. For best results, use a clean lens cloth to remove dust and fingerprint s from the screen. Do not wipe the shell of the TV with alcohol, methanol, gasoline or oil products to avoid dam- aging the finish. Wipe t he shell with a dry sof t cloth and use neutra l cleaning fluids. If your model ha ...
-
HANNspree F660-10A1 - page 55
54 Situation Solution No picture and sound. • Connect the power cord properly . • Press the POWER button on the control panel or remote control. • Press the SOURCE button to cycle thr ough connected video sources. • Press the CHANNEL UP or CHA NNEL DOWN button to switch to other TV stations. • Check the TV/CA TV OSD settings. See “TV/CA ...
-
HANNspree F660-10A1 - page 56
55 No sound but have image. • Make sure the source device is functioning properly . • Set the volume to a higher level. • Make sure the audio cable is connected securely . • T ur n the mute off. Screen image turns over . • Make sure the video signal cable is con- nected properly . Snow appears on the screen. • Adjust the location of the ...
-
HANNspree F660-10A1 - page 57
56 F660-10A1 LCD Panel Size 9.6-inch TFT Aspect Ratio 4:3 Best Resolution 800 (horizontal) x 600 (vertical) Maximum Display Area 194.4 mm (H) x 145.8 mm (W) TV System NTSC Video System S-Video Input and Composite Video Input (through the 4-IN-1 cable) Audio System Input: RCA Jack (L/R Audio Input through the 4-IN-1 cable) Output: 3.5mm ø headphone ...
-
HANNspree F660-10A1 - page 58
57 Aspect Ratio The ratio of width to height of a film, image or display screen. Broadcast TV Broadcasting video signals using high-frequency ele ctromagnetic waves to distribute television ch annels to viewers (standard TV broadcast). CA TV Community Antenna T elevision, the origin al name for cable TV . A television distribution system that uses ...
-
HANNspree F660-10A1 - page 59
58 S-V ideo Super-video, a video cabling standard used to transmit video by keeping brightness (Y) and color informa tion (C) on separate channels. Most often used with camcorders, VCRs, and quality re ceiver s and amplifiers to provide sharper pic- tures. VCD A compact disk format developed in 1993 by Sony and Philips to capture full- motion video ...
Avez-vous une question à propos de HANNspree F660-10A1?
Utiliser le formulaire ci-dessous
Si vous n’avez pas résolu votre problème avec HANNspree F660-10A1, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec HANNspree F660-10A1 il est probable qu’il a envie de partager la façon de le résoudre.