Français dropdown-ico

Manuel d’utilisation Craftsman 315.21212

36 pages 1.53 mb
Télécharger

Aller à la page of 36

Summary
  • Craftsman 315.21212 - page 1

    Owner's Manual 12 in. COMPOUND MITER SAW Double Insulated Model No. 315.212120 Save this manual for future reference. CAUTION: Read and follow all Safety Rules and Operating Instructions before first use of this product. Customer Help Line: 1-800-932-3188 Sears, Roebuck and Co., Hoffman Estates, IL 60179 USA Visit the Craftsman web page: www.s ...

  • Craftsman 315.21212 - page 2

    • Table of Contents ........................................................................................................................................... 2 • Warranty and Introduction ........................................................... _ .................................................................. 2 • Rules For Safe Operat ...

  • Craftsman 315.21212 - page 3

    The purpose of safety symbols Is to attract your attention to poulbio dangers. The safety Symbols, and the explanations with them, deserve your careful attention and uhderstanding. The safety warnings do not by themselvse eliminate any.JFlanger. The Instructions or warnings they give are not 8ubetltutee for proper accident prevention inseams. SYMBO ...

  • Craftsman 315.21212 - page 4

    RULES FOR SAFE OPERATION (Continued) m m USE THE PROPER EXTENSION CORD. Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resultingin loss of power and overheating. A wire gage size (A.W.G ...

  • Craftsman 315.21212 - page 5

    RULES FOR SAFE OPERATION (Continued) ALWAYS SUPPORT LONG WORKPIECES to minimize dsk of blade I_nching and kickback. Saw may slip, walk, or slide while cutting long or heavy beards. BEFORE •AKING A CUT, BE SURE ALL ADJUSTMENTS ARE SECURE. GUARD AGAINST KICKBACK. Kickback occurs when the blade stalls rapidly and workpioce is driven back towards the ...

  • Craftsman 315.21212 - page 6

    RULES FOR SAFE OPERATION (Continued) ALWAYS STAY ALERT! Do not allow familiarity (gained from frequent use of your saw) to cause a careless mistake. ALWAYS REMEMBER that a careless fraction of a second is sufficient to inflict severe injury. STAY ALERT AND EXERCISE CONTROL Watch what you ere doing and use common sense. Do not operate tool when you ...

  • Craftsman 315.21212 - page 7

    Blade Diameter 12 in. Blade Arbor 5/8 in. No Load Speed 4000 RPM Rating 120 Volts, 60 Hz-AC Only Input 15 Amperes Nat Weight 41 Ibs. Cutting Capacity with Miter at 0°/Bevel 0°: max width x resultingheight 7-7/8 in. x 2-1/2 in. Maximum Cutting Capacity with Miter at 45°/Bevel 0°: max width x resulting height 5-1/2 in. x 2-1/2 in. Maximum Cutting ...

  • Craftsman 315.21212 - page 8

    The following labels are onthe miter saw with loca- tions indicated, Restore lower blade guard andsecurely tighten screw before use DANGER: DO NOT REMOVE ANY GUARD. USE OF SAW WITHOUT THEIS GUARD WILL RESULT IN SERIOUS INJURY. tRNING / ADVERTENI • FOr your safety, read owners manual before oparutln • Wear eye protection, • Keep bends Out ut p ...

  • Craftsman 315.21212 - page 9

    The following items are included with your Compound Miter Saw: • SawBlade- 12in., • Miter Lock Handle • Dust Guide • Blade Wrench • 5 mm Hex Key Wrench • 6 mm Hex Key Wrench • 10 mm Hex Key Wrench • Owner's Manual F IO tam HEX KEY ,_ 6mm HEXKEY 5 mmHEXKEY MITER LOCK HANDLE BLADE WRENCH SAW BLADE DUST GUIDE Fig. 2 A WARNING: The ...

  • Craftsman 315.21212 - page 10

    KNOW YOUR COMPOUND MITER SAW See Figure 3. Before attempting to use your saw, familiarize yourself with all operating features and safety requirements. _i WARNING: Do not allow familiarity with your saw to make you careless. Remember that a careless fractionof a second is sufficient to inflict severe injury. 15 AMP MOTOR Your saw has a powerful 15 ...

  • Craftsman 315.21212 - page 11

    CARRYING HANDLE See Figure 4. For convenience when carrying or transporting your miter saw from one place to another, a carrying handle has been providedon top of the saw arm as shown in figure 4. To transport, turn off and unplug your saw, then lower the saw arm and lock it in the down position: Lock saw arm by depressing the lock pin. SAW ARM L ...

  • Craftsman 315.21212 - page 12

    POSITIVE STOPS ON MITER TABLE Positive stops have been provided at 0 °, 15 °, 22-1/'Z', 31.62 _, and 45° on beth the left and right side of the miter table. BEVEL LOCK KNOB The bevel lock knob securely locks your compound miter saw at desired hovel angles. Positive stop adjustment screws have been provided on each side of the saw arm. ...

  • Craftsman 315.21212 - page 13

    _, WARNING: To prevent accidental startingthat could cause possible serious personal injury, assemble all parts to your saw before connecting it to power supply. Saw should never be connected to power supply when you are assembling parts, making adjustments, installing or removing blades, or when not in use. As mentioned previouslyyour sew has been ...

  • Craftsman 315.21212 - page 14

    LOWER BLADE GUARD ARROW BLADE BOLT COVER TO (s) ON SPINDLE INNER BLADE TO WASHER WITH TIGHTEN DOUBLE'D" FLATS BLADE BOLT BLADE OUTER BLADE WASHER wm.I DOUBLE "D" FLATS Fig. 11 • Depress the spindle lock buttonand rotate the blade belt until the spindle looks. See Figure 12. • Using the blade wrench provided, loosen and remov ...

  • Craftsman 315.21212 - page 15

    Note: Many of the illustrations in this manual show only portionsof your compound miter saw. This is intentional so that we can clearly show points being made in the illustrations. Never operate your saw withoutall guards securely in place and in good operating condition. CUTTING A SLOT IN THE ZERO CLEARANCE THROAT PLATE In order to use your compou ...

  • Craftsman 315.21212 - page 16

    • Using a 6 mm hex key, loosen the socket head screws secudng the fence. See Figure 16. Adjust the fence left or dght until the framing square and zero clearance throat plate are parallel. • Retighten the screws securely and recheck the fence-to-table alignment. 6 mmSOCKET HEAD SCREWS 6 mmSOCKET HEAD SCREWS Fig. 16 SQUARING THE SAW BLADE TO THE ...

  • Craftsman 315.21212 - page 17

    • The edge of the square and the saw blade should be parallel as shown in figure 17. • If the front or back edge of the saw blade angles away from the square as shown in figures 18 and 19, adjustments are needed. • Using the 10 mm hex key provided, loosenthe socket head screws that secure the mounting bracket to the miter table. See Figure 20 ...

  • Craftsman 315.21212 - page 18

    FENCE COMBINATION = SQUARE MITER TABLE BLADE VIEW OF BLADE NOT SQUARE WITH MITER TABLE, ADJUSTMENTS ARE REQUIRED Fig. 23 • Using a 10 mm wrench or adjustable wrench, loosen the lock nut securing positive stop adjust- ment screw. Also loosen bevel lock knob. • Adjust positive stop adjustmentscrew to bring saw blade into alignment with the square ...

  • Craftsman 315.21212 - page 19

    DEPTH STOP ADJUSTMENT BEVEL LOCK KNOB MITER PosmvE TABLE STOP ADJUSmENT LOCK NUT(S) Fig. 25 • Lower the blade into the zero clearance throat plata of the miter table. Check blade clearance and maximum cuttingdistance (distance from fence where blade enters) to front of miter table sloL • Readjust if necessary. WARNING: Do not start your compoun ...

  • Craftsman 315.21212 - page 20

    STRAIGHT CROSSCUT C-CLAMP • Slowly lower the blade into and through the workpiece. See Figure 26. • • Release the switch trigger and allow the sew blade to stop rotating before raising the blade out of workpiece. Wait until the electric brake stops blade from fuming before removing the workpiece from the miter table. BEVEL CUT See Figures 27 ...

  • Craftsman 315.21212 - page 21

    Fig. 28 • Loosen the bevel look knob and move the sew arm to the left to the desired bevel angle. • Bevel angles can be set from 0 ° to 45 °. • For your convenience there is a double scale located on the mounting brackeL See F_jure 27. If one side becomes difficult to read as you move the saw arm to the left, simply refer to the other sid ...

  • Craftsman 315.21212 - page 22

    TO MAKE A COMPOUND CUT WITH YOUR MITER SAW: • Pull out the lock pin and lift saw arm to its full height. • Loosen the miter lock handle. Rotate the miter lock handle approximately one-half tom to the left to loosen. • Press the miter lock plate down with your thumb and hold. • Rotate the control arm untilthe pointer aligns with the desired ...

  • Craftsman 315.21212 - page 23

    • Before tuming on the saw, performa dry run of the cutting operationjust to make sure that no problems will occur when the cut is made. • Grasp the saw handle firmly, press the lock-off tab down, then squeeze the switch trigger. Allow sev- eral seconds for the blade to reach maximumspeed. • Slowly lower the blade into and through the workpie ...

  • Craftsman 315.21212 - page 24

    CUTTING COMPOUND MITERS To aid in making the correct settings, the compound angle seffing chart below has been provided. Since com- pound cuts are the most difficult to accurately obtain, trial cuts should be made in scrap material, and much thought and planning made, prior to making your required cut. PITCH _U_BER OF SIDES OFmDE 4 I 5 I 8 I 7 8 I ...

  • Craftsman 315.21212 - page 25

    cu'rI'ING CROWN MOLDING Your compound miter sew does an excellent job of cuttingcrown molding. In general, compound miter sews do a betterjob of cutting crown moldingthan any other tool made. In order to fit properly, crown molding must be com- pound mitered with extreme accuracy. The two contact surfaceson a piece of crown molding that f ...

  • Craftsman 315.21212 - page 26

    When cutting crown molding by this method the bevel angle should be set at 33.85 ° . The miter angle should be set at 31.62 ° either dght or left, depending on the desired cut for the application.See the chart below for correct angle settings and correct positioning of crown moldingon miter table. The settings in the chart below can be used for c ...

  • Craftsman 315.21212 - page 27

    _k WARNING: When servicing, use only identical Craftsman replacement ports. Use of any other part may create a hazard or cause product damage. GENERAL Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, c ...

  • Craftsman 315.21212 - page 28

    & WARNING: To ensure safety and reliability, all repairs -- with the exception of the externally accessible brushes -- should be performed by a qualified service technician at a Sears store to avoid risk of personal injury. BRUSH REPLACEMENT See Figure 36. BRUSH ASSEMBLYBRUSH CAP BRUSH CAP BRUSH ASSEMBLY Fig. 36 Your saw has externally accessib ...

  • Craftsman 315.21212 - page 29

    29 ...

  • Craftsman 315.21212 - page 30

    '----- CRAFTSMAN COMPOUND MITER SAW - MODEL NUMBER 315.212120 -'-- 27 28 34 4 Figure A 30 ...

  • Craftsman 315.21212 - page 31

    CRAFTSMAN COMPOUND MITER SAW - MODEL NUMBER 315.212120 ---, I The model number will be found on a plate attached to the motor housing. Always mentionthe model | number in all correspondence regarding your COMPOUND MITER SAW or when ordering repair ! parts. SEE BACK PAGE FOR PARTS ORDERING INSTRUCTIONS KEY PART NO. NUMBER 1 976512-001 2 976578-001 3 ...

  • Craftsman 315.21212 - page 32

    r_ CRAFTSMAN COMPOUND MITER SAW - MODEL NUMBER 315.212120 11 m 8 21 Figure B 54 52 7 49 23 24 50 42 41 30 ', 32 39 37 29 ...

  • Craftsman 315.21212 - page 33

    ¢o CRAFTSMAN COMPOUND MITER SAW - MODEL NUMBER 315.212120 I The model number will be found on a plate attached to the motor housing. Always mention the model number in all correspondence regarding your | COMPOUND MITER SAW or when ordering repair parts. J KEY PART NO. NUMBER 1 976512-001 2 980249-001 3 980255-001 4 980262-001 5 980238-001 6 980235 ...

  • Craftsman 315.21212 - page 34

    CRAFTSMAN COMPOUND MITER SAW - MODEL NUMBER 315.212120 SEE NOTE"A" O O 17 16 c_ 2 Figure C 7 6 4 18 ...

  • Craftsman 315.21212 - page 35

    GO O1 CRAFTSMAN COMPOUND MITER SAW - MODEL NUMBER 315.212120 I The model numberwill be found on a plate attached to the motor housing. Always mention the model number in all correspondenceregarding your I COMPOUND'MITER SAW or when ordering repair parts. I Key Part No. Number 1 980296-001 2 980288-001 3 "** 4 980270-001 5 980283-001 6 980 ...

  • Craftsman 315.21212 - page 36

    For in-home major brand repair service: Call 24 hours a day, 7 days a week 1-800-4-MY-Home s, (1-800-469-4663) Para pedir servicio de reparacibn a domicilio - 1-800-676-581t In Canada for all your service and parts needs cell - %800-665-4455 Au Canada pour tout le service ou les pibces For the repair or replacement parts you need: Call 7 am - 7 pm, ...

Fabricant Craftsman Catégorie Saw

Les documents que nous recevons du fabricant de l'appareilCraftsman 315.21212 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Craftsman
- manuels d’utilisations 315.21212
- fiches produit Craftsman
- dépliants
- ou étiquettes-énergie Craftsman 315.21212
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Craftsman 315.21212.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Craftsman 315.21212, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Craftsman 315.21212. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Craftsman 315.21212.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Craftsman 315.21212, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Craftsman 315.21212 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Craftsman 315.21212.

Le manuel d’utilisation complet Craftsman, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Craftsman 315.21212 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Craftsman 315.21212, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lCraftsman 315.21212 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Craftsman 315.21212 - qui devraient nous aider dans les premières étapes lors de l'utilisation Craftsman 315.21212
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Craftsman 315.21212
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Craftsman 315.21212 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Craftsman 315.21212?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Craftsman 315.21212, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Craftsman 315.21212 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)