Français dropdown-ico

Manuel d’utilisation InFocus IN5542

32 pages 1.4 mb
Télécharger

Aller à la page of 32

Summary
  • InFocus IN5542 - page 1

    1 Projector IN5542/IN5542c/IN5544/IN5544c User's Manual (T echnical) Resolution (H x V) H. frequency (kHz) V . frequency (Hz) Rating Signal mode 720 x 400 37.9 85.0 VESA TEXT 640 x 480 31.5 59.9 VESA VGA (60Hz) 640 x 480 37.9 72.8 VESA VGA (72Hz) 640 x 480 37.5 75.0 VESA VGA (75Hz) 640 x 480 43.3 85.0 VESA VGA (85Hz) 800 x 600 35.2 56.3 VESA S ...

  • InFocus IN5542 - page 2

    2 Initial set signals Initial set signals The following signals are used for initial settings. The signal timing for some computer models may be different. In this case, adjust the V POSITION and H POSITION in the IMAGE menu. Back porch (B) Front porch (D) Back porch (b) Front porch (d) Display time (C) Display time (c) Data Data H. Sync. V . Sync. ...

  • InFocus IN5542 - page 3

    3 Connection to the ports A COMPUTER IN1, B COMPUTER IN2, C MONITOR OUT D-sub 15pin mini shrink port • V ideo signal: RGB separate, Analog, 0.7Vp-p, 75Ω terminated (positive) • H/V . sync. signal: TTL level (positive/negative) • Composite sync. signal: TTL level At RGB signal Pin Signal Pin Signal 1 Video Red 9 (No connection) 2 V ideo Green ...

  • InFocus IN5542 - page 4

    4 I O HDMI DVI-D CONTROL IN CONTROL OUT REMOTE CONTROL IN OUT S-VIDEO COMPUTER IN2 COMPUTER IN1 VIDEO 1 BNC R/Cr/Pr G/Y B/Cb/Pb H V VIDEO 2 Y Cb/Pb Cr/Pr AC IN LAN MONITOR OUT REMOTE CONTROL K IN L OUT Ø3.5 stereo mini port • Connect to the projector's remote control. CONTROL M IN N OUT D-sub 9pin plug • For details of RS-232C communicati ...

  • InFocus IN5542 - page 5

    5 I O HDMI DVI-D CONTROL IN CONTROL OUT REMOTE CONTROL IN OUT S-VIDEO COMPUTER IN2 COMPUTER IN1 VIDEO 1 BNC R/Cr/Pr G/Y B/Cb/Pb H V VIDEO 2 Y Cb/Pb Cr/Pr AC IN LAN MONITOR OUT Connection to the por ts (continued) Q P O O HDMI • T ype :Digital video connector Pin Signal Pin Signal Pin Signal 1 T .M.D.S. Data2 + 8 T .M.D.S. Data0 Shield 15 SCL 2 T ...

  • InFocus IN5542 - page 6

    6 PJLink command PJLink command Commands Control Description Parameter or Response POWR Power Contorol 0 = Standby 1 = Power On POWR ? Power Status inquiry 0 = Standby 1 = Power On 2 = Cool Down INPT Input Source selection 1 1 = COMPUTER IN 1 12 = COMPUTER IN 2 13 = BNC 21 = COMPONENT 22 = S-VIDEO 23 = VIDEO 1 24 = VIDEO 2 31 = HDMI 32 = DVI-D INPT ...

  • InFocus IN5542 - page 7

    7 PJLink command (continued) Commands Control Description Parameter or Response LAMP ? Lamp Status inquiry 1st number (digits 1 to 5): Lamp T ime 2nd number : 0 = Lamp off, 1 = Lamp on INST ? Input Source List inquiry 1 1 12 13 21 22 23 24 31 32 NAME ? Projector Name inquiry Responds with the name set in "PROJECTOR NAME" of "NETWORK& ...

  • InFocus IN5542 - page 8

    8 RS-232C Communication RS-232C Communication 6 7 8 9 1 2 3 4 5 6 7 8 9 1 2 3 4 5 CONTROL port RS-232C cable (Cross) RS-232C port of the projector of the computer - (1) (1) CD RD (2) (2) RD TD (3) (3) TD - (4) (4) DTR GND (5) (5) GND - (6) (6) DSR RTS (7) (7) R TS CTS (8) (8) DTS - (9) (9) RI Connecting the cable 1. T urn off the projector and the ...

  • InFocus IN5542 - page 9

    9 RS-232C Communication (continued) Requesting projector status (Get command) (1) Send the request code Header + Command data (‘02H’+‘00H’+ type (2 bytes)+‘00H’ +‘00H’) from the computer to the projector . (2) The projector returns the response code ‘1DH’+ data (2 bytes) to the computer . Changing the projector settings (Set com ...

  • InFocus IN5542 - page 10

    10 Command Control via the Network Communication Port The following two ports are assigned for command control. TCP #23 TCP #9715 Command Control Settings Congure the following items from a web browser when command control is used. Command Control via the Networ k Port Settings Network Control Port1 (Port: 23) Port open Click the [Enable] check ...

  • InFocus IN5542 - page 11

    11 Command Control via the Networ k (continued) Command F or ma t [TCP #23] 1. Protocol Consist of header (7 bytes) + command data (6 bytes) 2. Header BE + EF + 03 + 06 + 00 + CRC_low + CRC_high CRC_low: Lower byte of CRC ag for command data CRC_high: Upper byte of CRC ag for command data 3. Command data Command data chart byte_0 byte_1 byte_ ...

  • InFocus IN5542 - page 12

    12 Command Control via the Networ k (continued) Decreasing the projector setting value (Decrement command) (1) The PC sends the following decrement code to the projector . Header + Command data (‘05H’ + ‘00H’ + type (2 bytes) + ‘00H’ + ‘00H’) (2) The projector decreases the setting value on the above setting code. (3) The projector ...

  • InFocus IN5542 - page 13

    13 7. R epl y Data The connection ID (the data is same as the connection ID data o n the sending data format) is attached to the Network control commands reply data. ACK reply: ‘06H’ + ‘xxH’ NAK reply: ‘15H’ + ‘xxH’ Error reply: ‘1CH’ + ‘xxxxH’ + ‘xxH’ Data reply: ‘1DH’ + ‘xxxxH’ + ‘xxH’ Projector busy reply: ...

  • InFocus IN5542 - page 14

    14 Daisy Chain Communication 1.Communications setting Set the same communication settings (selecting from options below) on the CONTROL terminal for transmitting and receiving side connected with a RS-232C cable. Baud rate: 4800 / 9600 / 19200 / 38400 bps Parity NONE / ODD / EVEN Data bit: 8 bit (xed) Start bit: 1 bit (xed) Stop bit: 1 bit (? ...

  • InFocus IN5542 - page 15

    15 Daisy Chain Communication Calculation of Checksum Sum up all of 12 bytes except the Checksum, then make the bit inversion of the lowest byte of the total, and add 1 to the inverted byte. The calculated result is the Checksum data. Exp. Communication Group: A / Communication ID: 1 Header data (7 bytes) Command data (6 bytes) Header Packet T ype D ...

  • InFocus IN5542 - page 16

    16 Daisy Chain Communication Command data ① Controlling projector byte_0 byte_1 byte_2 byte_3 byte_4 byte_5 Action T ype Setting Code low high low high low high Action (byte_0-1) Action Classication Content 1 Set Change setting to desired value. 4 Increment Increment setup value by 1. 5 Decrement Decrement setup value by 1. 6 Execute Run a com ...

  • InFocus IN5542 - page 17

    17 Daisy Chain Communication Command data Requesting projector status (Get command) (1) Send the following request code from the PC to the projector . Header + Command data (‘02H’ + ‘00H’ + type (2 bytes) + connection ID (2 bytes)) (2) The projector returns the response code to the PC. ‘9DH’ + ‘02H’ + connection ID (2 bytes) + data ...

  • InFocus IN5542 - page 18

    18 Daisy Chain Communication Get the number of connected projector s (1) Send the following request code from the PC to the projector . Header + Command data (‘02H’ + ‘00H’ + ‘00H’ + ‘00H’ + connection ID (2 bytes)) (2) The projector returns the response code to the PC. ‘9EH’ + ‘04H’ + connection ID (2 bytes) + number of pro ...

  • InFocus IN5542 - page 19

    19 Daisy Chain Communication Get the communication Group identication and Communication ID (1) Send the following request code from the PC to the projector . Header + Command data (‘02H’ + ‘00H’ + target number (2 bytes) + connection ID (2 bytes)) (2) The projector returns the response code to the PC. ‘90H’ + ‘04H’ + connection I ...

  • InFocus IN5542 - page 20

    20 RS-232C Communication / Netw or k command table Names Operation Type Header Command Data CRC Action T ype Setting Code RS-232C Communication / Network command table Power Set OFF BE EF 03 06 00 2A D3 01 00 00 60 00 00 ON BE EF 03 06 00 BA D2 01 00 00 60 01 00 Get BE EF 03 06 00 19 D3 02 00 00 60 00 00 (Example Return) 00 00 01 00 02 00 (Off) (On ...

  • InFocus IN5542 - page 21

    21 RS-232C Communication / Netw or k command table Names Operation Type Header Command Data CRC Action Type Setting Code GAMMA Set 5 CUSTOM BE EF 03 06 00 C7 FF 01 00 A1 30 14 00 6 CUSTOM BE EF 03 06 00 57 FE 01 00 A1 30 15 00 Get BE EF 03 06 00 F4 F0 02 00 A1 30 00 00 User Gamma Pattern Set Off BE EF 03 06 00 FB FA 01 00 80 30 00 00 9step Gray Sca ...

  • InFocus IN5542 - page 22

    22 Names Operation Type Header Command Data CRC Action Type Setting Code RS-232C Communication / Netw or k command table COLOR TEMP GAIN R Get BE EF 03 06 00 34 F4 02 00 B1 30 00 00 Increment BE EF 03 06 00 52 F4 04 00 B1 30 00 00 Decrement BE EF 03 06 00 83 F5 05 00 B1 30 00 00 COLOR TEMP GAIN G Get BE EF 03 06 00 70 F4 02 00 B2 30 00 00 Increment ...

  • InFocus IN5542 - page 23

    23 RS-232C Communication / Netw or k command table Names Operation Type Header Command Data CRC Action Type Setting Code 3D-YCS Set OFF BE EF 03 06 00 E6 70 01 00 0A 22 00 00 MOVIE BE EF 03 06 00 76 71 01 00 0A 22 01 00 STILL IMAGE BE EF 03 06 00 86 71 01 00 0A 22 02 00 Get BE EF 03 06 00 D5 70 02 00 0A 22 00 00 VIDEO NR Set LOW BE EF 03 06 00 26 7 ...

  • InFocus IN5542 - page 24

    24 RS-232C Communication / Netw or k command table Names Operation Type Header Command Data CRC Action Type Setting Code S-VIDEO FORMA T Set AUTO BE EF 03 06 00 E6 70 01 00 12 22 0A 00 NTSC BE EF 03 06 00 86 74 01 00 12 22 04 00 PA L BE EF 03 06 00 16 75 01 00 12 22 05 00 SECAM BE EF 03 06 00 16 70 01 00 12 22 09 00 NTSC4.43 BE EF 03 06 00 26 77 01 ...

  • InFocus IN5542 - page 25

    25 RS-232C Communication / Netw or k command table Names Operation Type Header Command Data CRC Action Type Setting Code FRAME LOCK - COMPUTER IN 1 Set OFF BE EF 03 06 00 3B C2 01 00 50 30 00 00 ON BE EF 03 06 00 AB C3 01 00 50 30 01 00 Get BE EF 03 06 00 08 C2 02 00 50 30 00 00 FRAME LOCK - COMPUTER IN 2 Set OFF BE EF 03 06 00 0B C3 01 00 54 30 00 ...

  • InFocus IN5542 - page 26

    26 Names Operation Type Header Command Data CRC Action Type Setting Code RS-232C Communication / Netw or k command table MONITOR OUT - HDMI Set COMPUTER IN 1 BE EF 03 06 00 7A F4 01 00 B3 20 00 00 COMPUTER IN 2 BE EF 03 06 00 BA F6 01 00 B3 20 04 00 BNC BE EF 03 06 00 4A F6 01 00 B3 20 07 00 OFF BE EF 03 06 00 8A B5 01 00 B3 20 FF 00 Get BE EF 03 0 ...

  • InFocus IN5542 - page 27

    27 RS-232C Communication / Netw or k command table Names Operation Type Header Command Data CRC Action Type Setting Code LANGUAGE Set POLSKI BE EF 03 06 00 97 D7 01 00 05 30 0E 00 TÜRKÇE BE EF 03 06 00 07 D6 01 00 05 30 0F 00 Get BE EF 03 06 00 C4 D3 02 00 05 30 00 00 MENU POSITION V Get BE EF 03 06 00 40 D7 02 00 16 30 00 00 Increment BE EF 03 0 ...

  • InFocus IN5542 - page 28

    28 RS-232C Communication / Netw or k command table Names Operation Type Header Command Data CRC Action Type Setting Code CLOSED CAPTION CHANNEL Set 1 BE EF 03 06 00 D2 62 01 00 02 37 01 00 2 BE EF 03 06 00 22 62 01 00 02 37 02 00 3 BE EF 03 06 00 B2 63 01 00 02 37 03 00 4 BE EF 03 06 00 82 61 01 00 02 37 04 00 Get BE EF 03 06 00 71 63 02 00 02 37 0 ...

  • InFocus IN5542 - page 29

    29 RS-232C Communication / Netw or k command table Names Operation Type Header Command Data CRC Action Type Setting Code MY BUTTON-1 Set COMPUTER IN 1 BE EF 03 06 00 3A 33 01 00 00 36 00 00 COMPUTER IN 2 BE EF 03 06 00 FA 3 1 01 00 00 36 04 00 BNC BE EF 03 06 00 0A 31 01 00 00 36 07 00 HDMI BE EF 03 06 00 CA 33 01 00 00 36 03 00 DVI-D BE EF 03 06 0 ...

  • InFocus IN5542 - page 30

    30 RS-232C Communication / Netw or k command table Names Operation Type Header Command Data CRC Action Type Setting Code MY BUTTON-3 Set DVI-D BE EF 03 06 00 D2 34 01 00 02 36 09 00 COMPONENT BE EF 03 06 00 D2 31 01 00 02 36 05 00 S-VIDEO BE EF 03 06 00 E2 33 01 00 02 36 02 00 VIDEO 1 BE EF 03 06 00 12 33 01 00 02 36 01 00 VIDEO 2 BE EF 03 06 00 22 ...

  • InFocus IN5542 - page 31

    31 RS-232C Communication / Netw or k command table Names Operation Type Header Command Data CRC Action Type Setting Code MY SOURCE Get BE EF 03 06 00 C9 38 02 00 20 36 00 00 MY IMAGE Set OFF BE EF 03 06 00 3A C3 01 00 00 35 00 00 IMAGE-1 BE EF 03 06 00 AA C2 01 00 00 35 01 00 IMAGE-2 BE EF 03 06 00 5A C2 01 00 00 35 02 00 IMAGE-3 BE EF 03 06 00 CA ...

  • InFocus IN5542 - page 32

    32 Names Operation Type Header Command Data CRC Action Type Setting Code RS-232C Communication / Netw or k command table LENS MEMORY INDEX Set 1 BE EF 03 06 00 4B 92 01 00 07 24 00 00 2 BE EF 03 06 00 DB 93 01 00 07 24 01 00 3 BE EF 03 06 00 2B 93 01 00 07 24 02 00 Get BE EF 03 06 00 78 92 02 00 07 24 00 00 LENS MEMORY LOAD Execute BE EF 03 06 00 E ...

Fabricant InFocus Catégorie Projector

Les documents que nous recevons du fabricant de l'appareilInFocus IN5542 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques InFocus
- manuels d’utilisations IN5542
- fiches produit InFocus
- dépliants
- ou étiquettes-énergie InFocus IN5542
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation InFocus IN5542.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation InFocus IN5542, manuels d’entretien, brefs manuels ou manuels de l’utilisateur InFocus IN5542. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit InFocus IN5542.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil InFocus IN5542, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser InFocus IN5542 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs InFocus IN5542.

Le manuel d’utilisation complet InFocus, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel InFocus IN5542 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières InFocus IN5542, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lInFocus IN5542 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil InFocus IN5542 - qui devraient nous aider dans les premières étapes lors de l'utilisation InFocus IN5542
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de InFocus IN5542
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service InFocus IN5542 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de InFocus IN5542?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec InFocus IN5542, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec InFocus IN5542 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)