Manuel d’utilisation Aztech Systems 32

14 pages 0.33 mb
Télécharger

Aller à la page of 14

Summary
  • Aztech Systems 32 - page 1

    - 1 - Version 1-2000 Novemb er 2000 OPERATION AND MA INTENANCE MANU A L FOR TX 2, 4, 8, 16, 32 LOW PROFILE HYDRAUL IC TORQUE WRENCHES Series TX-2, T X-4, T X-8, TX-16 and TX- 32 Low Prof ile Hydraulic T orque Wren ches are d esigned fo r installing and removin g large bo lts hav ing minima l wrench clearance at o ffsh ore platforms , pow er plants, ...

  • Aztech Systems 32 - page 2

    - 2 - FAILURE TO OBS ERVE THE FOLLOWING W ARNINGS COULD RESULT IN INJ URY USING TH E TOOL • Keep hands, lo ose clot hing and long hair aw ay fro m the re action a rm and w orking area during operatio n. Do no t attempt to support the t ool wit h your ha nds during o peration. • This too l will exert a strong react ion forc e. Use proper mechani ...

  • Aztech Systems 32 - page 3

    - 3 - PLACING THE TOOL IN SERVICE ADJUSTMENTS SETTING THE TORQUE After deter mining the desir ed torq ue, use the torque c on- version chart on the Shro ud or the tor que conversio n charts on page s 5 and 6 to deter mine the pressure that is necessar y to achieve that torque. 1. Connect t he tool to the po wer supply and turn t he pump on. 2. Dep ...

  • Aztech Systems 32 - page 4

    - 4 - TX Series T orque Con version Chart Bar/N.M. TX-2 TX-4 TX-8 TX-16 TX-32 Hex 3/4" to 1-13/1 6" 1-7/8" to 2 -3/8" All Hex Sizes All Hex Sizes 2-5/8" to 3 -15/16" 4" to 4-5/8" 2-7/16" to 4-5/8" 4-11/16" to 6-1/2" Sizes 19 to 46MM 47 to 60MM All Hex Sizes All Hex Sizes 65 to 100MM 105 to ...

  • Aztech Systems 32 - page 5

    - 5 - TX Series Torque Conversion Chart P.S.I./FT./lbs TX-2 TX-4 TX-8 T X-16 TX-32 Hex 3/4" to 1-13/1 6" 1-7/8" to 2 -3/8" All Hex Sizes All Hex Sizes 2-5/8" to 3 -15/16" 4" to 4-5/8" 2-7/16" to 4-5/8" 4-11/16" to 6-1/2" Sizes 19 to 46MM 47 to 60MM All Hex Sizes All Hex Sizes 65 to 100MM 1 ...

  • Aztech Systems 32 - page 6

    - 6 - TX - 16, TX - 32 SERIES LINK TX - 2, TX - 4, TX - 8 SERIES LINK ...

  • Aztech Systems 32 - page 7

    - 7 - Part Numbers for Ordering (LINKS) Part TX2 TX4 T X8 TX16 TX32 1 SIDE PL A TE - L TX-2- L01 TX-4- L01 TX-8- L01 TX-16- L01 TX-32- L01 2 SIDE PL A TE - R TX-2- L02 TX-4- L02 TX-8- L02 TX-16- L02 TX-32- L02 3 DRIVE PL ATE TX-2- L03 TX-4- L03 TX-8- L03 TX-16- L03 TX-32- L03 4 DRIVE PIN TX-2- L05 TX-4- L05 TX-8- L05 TX-16- L05 TX-32- L05 5 DRIVE P ...

  • Aztech Systems 32 - page 8

    - 8 - TX - 2, TX - 4, TX - 8 SERIES CYLINDER TX - 16, TX - 32 SERIES CYLINDER ...

  • Aztech Systems 32 - page 9

    - 9 - Part Numbers for Ordering (CYLIND ERS) Part TX2 T X4 TX8 TX16 TX32 1 HOUSING TX-2-C01 TX-4-C01 TX-8-C01 TX-1 6-C01 TX-32-C01 PISTON ROD A SSEM BLY TX-2 -C03 TX-4-C03 TX-8-C03 TX-16 -C03 TX-32-C03 2 PISTON ROD TX-2-C03-1 N/A N/A TX-16-C03-1 TX-32-C03-1 3 PISTON C A P N/A N/A N/A TX-16-C03-2 TX-32-C03-2 VALVE B ALL N/A N/A N/A TX-16-C03-3 TX-32 ...

  • Aztech Systems 32 - page 10

    - 10 - Maintenance Section Alway s turn off t he powe r supply, bleed off hydraulic fluid fro m the hose co nnections on the cy linder assembly and disconnect t he hoses before a ttempting to repa ir or perfor m maintenance on this to ol. Alway s wear eye pr otectio n when opera ting or perfor ming maintenance on t his tool. DISASSEMBLY General Ins ...

  • Aztech Systems 32 - page 11

    - 11 - unscrew and r emove the pisto n head fro m the sha ft with the Pisto n O-ring (1 7). 7. Pull the Piston shaft out o f the Housing. 8. If the Sliders ( 5) must be re placed, position the Slider Pin (14 ) over a clear ance opening in a soft bloc k and use a small dr ift to tap the Pin out of the Sliders and shaft. 9. If the Rod Seal (16) needs ...

  • Aztech Systems 32 - page 12

    - 12 - 7. Wipe a thin film of Marine G rade Moly Lube onto t he inner race of t he large op ening in the Dri ve Plate. 8. Position the Ratc het (6) in the central o pening of the Drive Plate. 9. Insert the Dri ve Segment (7 ) into the op ening adja cent to the Ratchet. M ake cert ain t he tee th of the R atchet corre ctly engage the t eeth of t he ...

  • Aztech Systems 32 - page 13

    - 13 - the outer edge o f both Slid ers or d eep enough to prevent the sha ft ends from dragging o n the Hous ing walls. 6. Install the Pisto n O-ring (1 7) in the inter nal groove of the Seal Ring ( 5). 7. Install the asse mbled Seal Ring and P iston O-rin g on the hub at the lar ge end o f the P iston Rod. 8. Install the Pisto n Seal P late (4) i ...

  • Aztech Systems 32 - page 14

    - 14 - Troubleshootin g Guide Trouble Probable Cause Solution Couplers are not securely at tached to the tool or pump Check the Coupler connections and m ake certain that they are connected. Coupler is defective Replace any defective Coupler. Defective remote control switch Repl ace the switch and/or c ontrol pendent Piston will not advance or retr ...

Fabricant Aztech Systems Catégorie Impact Driver

Les documents que nous recevons du fabricant de l'appareilAztech Systems 32 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Aztech Systems
- manuels d’utilisations 32
- fiches produit Aztech Systems
- dépliants
- ou étiquettes-énergie Aztech Systems 32
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Aztech Systems 32.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Aztech Systems 32, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Aztech Systems 32. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Aztech Systems 32.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Aztech Systems 32, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Aztech Systems 32 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Aztech Systems 32.

Le manuel d’utilisation complet Aztech Systems, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Aztech Systems 32 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Aztech Systems 32, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lAztech Systems 32 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Aztech Systems 32 - qui devraient nous aider dans les premières étapes lors de l'utilisation Aztech Systems 32
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Aztech Systems 32
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Aztech Systems 32 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Aztech Systems 32?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Aztech Systems 32, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Aztech Systems 32 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Commentaires (0)