Manuel d’utilisation Rinnai FS35ETRSN/US

28 pages 1.6 mb
Télécharger

Aller à la page of 28

Summary
  • Rinnai FS35ETRSN/US - page 1

    FS35ETRBN/US FS35ETRSN/US FS35ETRBL/US FS35ETRSL/US Gas Radiant Sp ace Heater Owners Operation and Inst allation Manual Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. WHA T T O DO IF YOU SMELL GAS • Do not try to light any appliance. • Do not touch any electrical switch; do not ...

  • Rinnai FS35ETRSN/US - page 2

    2 LIMITED W ARRANTY RINNAI FIREPLACE HEA TER WHA T IS COVERED? This W arranty covers any defects in materials or workmanship, subject to the terms st ated below . This Warranty extends to the original purchaser and subsequent transferees, but only while the product remains at the site of the original installation. This Warranty only extends through ...

  • Rinnai FS35ETRSN/US - page 3

    3 W ARNING IMPROPER INST ALLA TION, ADJUSTMENT , AL TERA TION, SERVICE OR MAINTENANCE CAN CAUSE PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE. INST ALLA TION AND SER VICE MUST BE PERFORMED BY A QUALIFIED INST ALLER, SERVICE AGENCY OR THE GAS SUPPLIER. Freest anding Fire ETR Electronic Timer Remote T able of Content s Limited warranty ........... ...

  • Rinnai FS35ETRSN/US - page 4

    4 Model: FS35ETRBN/US, FS35ETRSN/US (NG) United S tates FS35ETRBL/US, FS35ETRSL/US (Propane) United S tates Description: Freest anding radiant/convector , glass-fronted, ceramic log space heater with forced convection and natural draft flue system Output: 24,000 Btu/hr Natural Gas 22,000 Btu/hr Propane Gas Control: Electronic control valve Burners: ...

  • Rinnai FS35ETRSN/US - page 5

    5 8 Read these rules and the instructions carefully . Check all local codes. Failure to follow these could cause a malfunction of the heater resulting in death, serious bodily injury and/or property damage. 9 This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible for use with other gases ...

  • Rinnai FS35ETRSN/US - page 6

    6 Diagram shows minimum clearances from combustible materials of the control system and any gas control which has been under water . 1 7 Adequate clearances for accessibility for purposes of servicing and proper operation should be provided. 1 8 Adequate clearances around air openings into the combustion chamber should be provided. 19 Do not instal ...

  • Rinnai FS35ETRSN/US - page 7

    7 TECHNICAL SPECIFICA TIONS COMP ARTMENTS, BURNERS AND CIRCULA TING AIR P ASSAGEW A YS OF THE APPLIANCE ARE KEPT CLEAN. 35 The glass window shall be replaced as one piece as supplied by the manufacturer . See log and glass installation on page 15. 3 6 Do not substitute glass, glowing embers or logs. Use only glass, glowing embers and logs supplied ...

  • Rinnai FS35ETRSN/US - page 8

    8 A This appliance is equipped with an ignition device which automatically ignites the pilot. Do not try to light the pilot by hand B. BEFORE OPERA TING smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor . WHA T TO DO IF YOU SMELL GAS • Do not try to li ...

  • Rinnai FS35ETRSN/US - page 9

    9 For your convenience the controls on your new Flame Fire are situated under the cover on the top right-hand side of the fire and are accessed by simply lifting the lid. All necessary adjustments to the operation of your fire can be made with these controls. OPERA TION CONTROL P ANEL LA YOUT • TURNING ON Press the ON/OFF button to operate the un ...

  • Rinnai FS35ETRSN/US - page 10

    10 deactivate the LOCK press and hold the button for 3 seconds until the indicator goes off. During normal operation the LOCK may be activated and all controls, other than the OFF switch, will be locked. Deactivating the LOCK releases the controls. If the LOCK is activated while the unit is turned OFF , then all functions will be locked including t ...

  • Rinnai FS35ETRSN/US - page 11

    11 proceed to TIMER 2 - which is programmed in the same way - or three times to return to the clock display . This must be done within 1 minute of setting the time to lock it into the memory . The digital display will show the current time. A small indicator on the digital display will flash to show that the display has returned to the clock. After ...

  • Rinnai FS35ETRSN/US - page 12

    12 NOTE: Some fluorescent lights may interfere with the transmission of remote control signals, in this case changing the position from which you are operating the remote control may help. Avoid getting the remote control wet, or dropping it. The remote control works within 15 feet and an angle of 40° to the receiver on the unit. • TO REPLACE RE ...

  • Rinnai FS35ETRSN/US - page 13

    13 1. Flue connection and proper venting 2. W arm air distribution. 3. Adequate air supply . 4. The heater must not be installed where curtains or other combustible materials could come into contact with it. In some cases, curtains may need restraining. See below for minimum clearances required. LOCA TION When positioning the heater , the main poin ...

  • Rinnai FS35ETRSN/US - page 14

    14 • RUN GAS SUPPL Y For pipe sizing, refer to your local gas installation codes. • PURGE SUPPL Y OF AIR AND DEBRIS All foreign materials such as filings must be purged from the gas supply , as they may cause the gas valve to malfunction. A means to measure the gas pressure immediately upstream of the supply connection to the appliance shall be ...

  • Rinnai FS35ETRSN/US - page 15

    15 The logset is packed inside the unit and the packaging must be removed prior to installing the logset in its correct position. • Open both side panels. • Remove fasteners on both sides of the top glass retainer . • Lift retainer away from unit. • Loosen screws on bottom glass retainer . • Carefully lift glass out of bottom channel. • ...

  • Rinnai FS35ETRSN/US - page 16

    16 • TESTING PROCEDURE T urn gas supply on and plug the unit into the power supply . (Caution 1 15V) • TO CHECK BURNER PRESSURE • Refer to rating plate. • Remove the wiring cover panel. • Remove test point plug and attach manometer to test point. The test point is on the bottom front face of the gas valve. • Light heater , turn to High ...

  • Rinnai FS35ETRSN/US - page 17

    17 IMPORT ANT MAINTENANCE INSTRUCTIONS ANNUAL INSPECTION The unit should be inspected at least once a year by a qualified service technician including inspection of the flue system. The appliance area must be kept clear and free from combustible materials, gasoline and other flammable vapors and liquids. • CLEANING INSTRUCTIONS. Before cleaning, ...

  • Rinnai FS35ETRSN/US - page 18

    18 1 3 3 2 1 1 3 4 2 2 The heater should be serviced annually only by an authorised person. • GLASS REPLACEMENT AND CLEANING . (May be performed by the owner) It is best to handle the glass with clean gloves to avoid smearing the glass with finger prints which might show after replacement. Refer diagram opposite Loosen the side panel retaining sc ...

  • Rinnai FS35ETRSN/US - page 19

    19 WIRING DIAGRAM PCB LA YOUT Caution: Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. V erify proper operation after servicing. ...

  • Rinnai FS35ETRSN/US - page 20

    20 NOTE: If you have any other faults or problems, please refer to your Installer or local qualified service agency TROUBLE SHOOTING WIRING DIAGRAM-LADDER SY M PT OM CA USE SOLUTION N o pow er pres ent Ens ur e pow er c or d is plugged in and t ur ned on N o gas pres ent Ens ur e gas s upply is t urned on pow er c ut R e- ignite aft er pow er is r ...

  • Rinnai FS35ETRSN/US - page 21

    21 E r r or code P r obabl e cause C ommen ts 11 I g ni ti o n fai lure C h e ck gas i s t u rn ed o n . Serv i ce cal l i f r epeat ed 12 Fl am e f ail u r e C h e ck gas i s t u rn ed o n . Serv i ce cal l i f r epeat ed 14 O v er h eat Ser v ice c al l 16 R oom ov e r h eat Low er r om t emper au re t o l e ss t h a n 104° F 31 Ser v ice ca l l ...

  • Rinnai FS35ETRSN/US - page 22

    22 EXPLODED DIAGRAMS ...

  • Rinnai FS35ETRSN/US - page 23

    23 ...

  • Rinnai FS35ETRSN/US - page 24

    24 SP ARE P ARTS LIST I T EM N O. Q T Y. PAR T N O . 1 1 7 9 9 2- 1 FL U E SPI GO T ASSY FS N AT U SA 2 1 7 0 7 4 H EAT EX C H AN GER FR ON T ASSY 3 + 3 H 3 1 7 0 7 5 H EAT EX C H AN GER R EAR ASSY 3 H 4 6 6 6 2 4 BU R N ER EX C H AN G ER T R AN SFER T U BE 5 2 6 6 2 5 BU R N ER H EAT EX C H AN G ER BR AC KET 6 1 70 28-5 F LUE S P IGO T DRA UGHT DI ...

  • Rinnai FS35ETRSN/US - page 25

    25 5 1 1 7 9 8 8 V R EAR PAN EL F S3 5 ET R VI PER U SA BL AC K 1 7 9 8 8S P R EAR PAN EL FS3 5E T R SP U SA SI L VER 52 1 7472 A IR GUI DE LOW E R FS 35E T R 5 3 1 7 0 6 2 H EAT SH I EL D LO W ER R H FS ET R 54 1 7060 HE A T S HI E LD LOW E R LH FS 55 2 75 64 E LE CTRODE S LE E V E 5 6 1 7 4 8 2 V T OP PAN EL ASSY F S3 5 ET R VI PER BL AC K 1 7 4 ...

  • Rinnai FS35ETRSN/US - page 26

    26 INST ALLA TION NOTES ...

  • Rinnai FS35ETRSN/US - page 27

    27 1 . W as a fireplace inspection carried out? (i.e. clearances, combustibles etc.) 2. W as a manufactured flue system installed? 3 . Has specified gas pressure been set? 4 . Are decorative logs located correctly on pins? 5. Have ember granules been placed and free of dust and powder? 6.Has the appliance been test fired for correct operation (All ...

  • Rinnai FS35ETRSN/US - page 28

    Part Number 7917 zx ...

Fabricant Rinnai Catégorie Fan

Les documents que nous recevons du fabricant de l'appareilRinnai FS35ETRSN/US peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Rinnai
- manuels d’utilisations FS35ETRSN/US
- fiches produit Rinnai
- dépliants
- ou étiquettes-énergie Rinnai FS35ETRSN/US
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Rinnai FS35ETRSN/US.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Rinnai FS35ETRSN/US, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Rinnai FS35ETRSN/US. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Rinnai FS35ETRSN/US.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Rinnai FS35ETRSN/US, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Rinnai FS35ETRSN/US par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Rinnai FS35ETRSN/US.

Le manuel d’utilisation complet Rinnai, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Rinnai FS35ETRSN/US - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Rinnai FS35ETRSN/US, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lRinnai FS35ETRSN/US qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Rinnai FS35ETRSN/US - qui devraient nous aider dans les premières étapes lors de l'utilisation Rinnai FS35ETRSN/US
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Rinnai FS35ETRSN/US
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Rinnai FS35ETRSN/US dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Rinnai FS35ETRSN/US?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Rinnai FS35ETRSN/US, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Rinnai FS35ETRSN/US il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Commentaires (0)