Français dropdown-ico

Manuel d’utilisation Porter-Cable 33-890

32 pages 3.32 mb
Télécharger

Aller à la page of 32

Summary
  • Porter-Cable 33-890 - page 1

    INSTRUCTION MANUAL 12" Radial Arm Saw (Model 33-890, 33-895X, 33-891, 33-892) P ART NO. 424-02-651-0025 - 03-18-05 Copyright © 2005 Delta Machinery T o learn more about DEL T A MACHINER Y visit our website at: www .deltamachinery .com. For Parts, Service, W arranty or other Assistance, please call 1-800-223-7278 ( In Canada call 1-800-463-358 ...

  • Porter-Cable 33-890 - page 2

    2 T ABLE OF CONTENTS Read and understand all warnings and operating instructions before using any tool or equipment. When using tools or equipment, basic safety precautions should always be followed to r educe the risk of personal injury . Improper operation, maintenance or modification of tools or equipment could r esult in serious injury and prop ...

  • Porter-Cable 33-890 - page 3

    3 Indicates an imminently hazardous situation which, if not avoided, will r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, could r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, may r esult in minor or moderate injury . Used without the saf ...

  • Porter-Cable 33-890 - page 4

    4 GENERAL SAFETY RULES READ AND UNDERST AND ALL W ARNINGS AND OPERA TING INSTRUCTIONS BEFORE USING THIS EQUIPMENT . Failure to follow all instructions listed below , may result in electric shock, fire, and/or serious personal injury or pr operty damage. IMPORT ANT SAFETY INSTRUCTIONS 1. FOR YOUR OWN SAFETY , READ THE INSTRUCTION MANUAL BEFORE OPERA ...

  • Porter-Cable 33-890 - page 5

    5 1 . DO NOT OPERA TE THIS MACHINE UNTIL it is assembled and installed according to the instructions. 2. OBT AIN ADVICE from your supervisor, instructor , or another qualified person if you are not familiar with the operation of this machine. 3. FOLLOW ALL WIRING CODES and recommended electrical connections. 4. USE THE GUARDS WHENEVER POSSIBLE. Che ...

  • Porter-Cable 33-890 - page 6

    6 6 Fig. A GROUNDED OUTLET BOX CURRENT CARR YING PRONGS GROUNDING BLADE IS LONGEST OF THE 3 BLADES A separate electrical circuit should be used for your machines. This cir cuit should not be less than #12 wire and should be protected with a 20 Amp time lag fuse. If an extension cor d is used, use only 3-wire extension cor ds which have 3- prong gr ...

  • Porter-Cable 33-890 - page 7

    7 EXTENSION CORDS Use proper extension cor ds. Make sure your extension cord is in good condition and is a 3-wir e extension cord which has a 3-pr ong grounding type plug and matching receptacle which will accept the machine’ s plug. When using an extension cor d, be sure to use one heavy enough to carry the current of the machine. An undersized ...

  • Porter-Cable 33-890 - page 8

    8 FUNCTIONAL DESCRIPTION UNP ACKING AND CLEANING Carefully unpack the machine and all loose items fr om the shipping container(s). Remove the protective coating from all unpainted surfaces. This coating may be removed with a soft cloth moistened with kerosene (do not use acetone, gasoline or lacquer thinner for this purpose). After cleaning, cover ...

  • Porter-Cable 33-890 - page 9

    9 ASSEMBL Y ASSEMBL Y TOOLS REQUIRED ASSEMBL Y TIME ESTIMA TE - 2-3 hrs. * Blade wrenches (supplied) * 1 / 2 ” and 3 / 8 ” open end or socket wr enches (not included) * 5 / 16 ” hex wr ench (not included) * Flat screwdriver and hammer (not included) The following is an explanation of the operating controls of the Delta 12” Radial Saw . W e ...

  • Porter-Cable 33-890 - page 10

    10 Fig. 4A ASSEMBLING LEGS TO BASE Mechanically lift the machine using a forklift and lifting straps to support the machine. The four steel legs should be attached to each corner of the base using sixteen 5/16-18 x 5/8" carriage head screws (A) Fig. 4A and Fig. 4B, 5/16" flat washers (B), 5/16" lockwashers (C) and 5/16" hex nuts ...

  • Porter-Cable 33-890 - page 11

    11 Fig. 8 Fig. 9 Fig. 11 Fig. 10 5. Unscrew and remove blade guar d clamping rod and washer (G) Fig. 9, and remove blade guar d assembly (H). 6. Place cuttinghead clamp (J) Fig. 10, in slot on top of cuttinghead. NOTE: Jaws of cuttinghead clamp must be open as shown. 7. Lift cuttinghead assembly (B) Fig. 11, and insert roller bearings (K) into trac ...

  • Porter-Cable 33-890 - page 12

    12 Fig. 15 Fig. 12 Fig. 13 Fig. 14 3. Fig. 15, illustrates the starter box assembled to the base. ASSEMBLING ST ARTER BOX TO BASE (33-891 AND 33-892 MODELS) If you purchased your machine with magnetic starter , transformer and overload protection, assemble the starter box to the base, as follows: 1. Assemble bracket (A) to the bottom of the right s ...

  • Porter-Cable 33-890 - page 13

    13 Fig. 16 Fig. 17 Fig. 18 ADJUSTING T ABLE BRACKETS P ARALLEL TO TRACK ARM T o perform accurate work, the track arm must be parallel to the table top brackets at both the front and r ear of the machine. T o check if the alignment is correct, proceed as follows: 1. Loosen yoke clamp locking lever (A) Fig. 16, pull up yoke clamp index knob (B) and r ...

  • Porter-Cable 33-890 - page 14

    14 Fig. 19 Fig. 21 Fig. 20 Fig. 22 4. Loosen cuttinghead clamp knob (J) Fig. 20 and move cuttinghead (C) to the front of track arm (K). Loosen track arm locking lever (L), pull out on track arm index knob (M) and rotate track arm (K) until wr ench (F) is over left table bracket (N). Make certain wrench (F) is in the vertical position and tighten kn ...

  • Porter-Cable 33-890 - page 15

    15 Fig. 26 Fig. 23 Fig. 24 Fig. 25 7. If an adjustment is necessary , remove scr ew (R) Fig. 23, loosen locknut (S) and turn leveling screw (T) to raise or lower table mounting bracket (N). When adjust- ment is complete, tighten locknut (S) and replace scr ew (R). 8. Check and adjust the other table mounting bracket in the same manner . IMPORT ANT ...

  • Porter-Cable 33-890 - page 16

    16 ASSEMBLING T ABLE BOARDS 1. Place main table board (A) Fig. 27, on the table mounting brackets making sure that the two r oll pins in the table mounting brackets fit into the two holes in bottom of main table board (A). Fasten table in place, place a 1/4" flat washer onto a 1/4-20 x 1-3/4" round head screw and insert the scr ews throug ...

  • Porter-Cable 33-890 - page 17

    17 Fig. 31 Fig. 32 5. Remove screw , flat washer and spacer (G) Fig. 31, that fasten the front inside leaf guar d (H) to front end of blade guard (J). Assemble blade guar d (J) to motor assembly with locking rod and washer (K). 6. Reassemble leaf guard (H) Fig. 31, to blade guard (J) using screw , flat washer and spacer (G). 7. Fig. 32, illustrates ...

  • Porter-Cable 33-890 - page 18

    Fig. 36 Fig. 37 Fig. 38 ADJUSTING OVERARM COLUMN If side motion develops in the overarm, after extended use, it can be corrected as follows: 1. DISCONNECT MACHINE FROM POWER SOURCE. 2. Loosen hex nuts (A) Fig. 36, and gib adjusting screws (B) and (C). 3. Adjustment to the column base is made by loosening hex nuts (D) Fig. 36, tightening or loosenin ...

  • Porter-Cable 33-890 - page 19

    19 Fig. 39 Fig. 40 Fig. 41 ADJUSTING CUTTINGHEAD BALL BEARINGS AGAINST TRACK RODS The carriage is mounted on four pre-loaded, pr e- lubricated, shielded ball bearings: two on fixed shafts (on saw blade side of track arm); the other two on adjustable eccentric shafts. The ball bearings must ride smoothly and evenly against the track rods to do accur ...

  • Porter-Cable 33-890 - page 20

    20 Fig. 45 Fig. 44 Fig. 43 Fig. 42 ADJUSTING BLADE SQUARE WITH T ABLE TOP The saw blade must be square with the table top in order to pr oduce accurate work. T o check if the blade is square with the table: 1. DISCONNECT MACHINE FROM POWER SOURCE. 2. Remove the blade guard and place the cuttinghead in a cross-cut position as shown in Fig. 42. 3. Pl ...

  • Porter-Cable 33-890 - page 21

    21 Fig. 46 Fig. 47 Fig. 49 Fig. 48 7. When the adjustment is made, tur n the bevel clamp handle (F) Fig. 46, counterclockwise to lock the motor in position. NOTE: If the bevel clamp handle (F) does not completely lock the motor , the clamp handle can be re- positioned by pulling out the handle and repositioning it on the serrated nut located under ...

  • Porter-Cable 33-890 - page 22

    22 Fig. 50 Fig. 51 Fig. 52 Fig. 53 ADJUSTING SAW TRA VEL SQUARE WITH FENCE The 12” Radial Arm Saw is equipped with 90° and 45° positive miter stops. This feature makes it possible to produce accurate miter cuts and squar e cross-cuts at all times. T o do accurate work, the saw blade travel must be 90° to the fence. If saw blade travel is not 9 ...

  • Porter-Cable 33-890 - page 23

    23 Fig. 54 Fig. 55 Fig. 56 REMOVING “HEELING” IN SAW CUT Even though the cuttinghead travel may be perfectly aligned at 90° to the fence, the blade itself may not be 90° or square with the fence, as shown in Fig. 54. This condition is known as “heeling.” T o check and adjust, proceed as follows: 1. DISCONNECT MACHINE FROM POWER SOURCE. 2. ...

  • Porter-Cable 33-890 - page 24

    24 ADJUSTING BLADE GUARD AND ANTI-KICKBACK ROD On all ripping and plowing operations, the infeed side of the blade guard is lower ed so that it just clears the material. This will prevent the material fr om being lifted off the table. Also, lower the kickback r od (A) Fig. 57, so that the kickback fingers (B) are below surface of material. Rod (A) ...

  • Porter-Cable 33-890 - page 25

    25 CROSS-CUTTING The first operation which should be learned on the radial saw is cross-cutting. Cr oss-cutting consists of supporting the workpiece against the fence and pulling the saw blade through the material at right angles to it. When cross-cutting, the track arm (A) should be indexed at “0” and the track arm clamp handle (B) Fig. 62, ti ...

  • Porter-Cable 33-890 - page 26

    26 Fig. 63 Fig. 64 Fig. 65 B A B C A COMPOUND MITER CUTTING Compound miter cutting is performed in the same manner as miter cutting except the saw blade is also tilted to cut a bevel. The settings and operation are similar to miter cutting except that the blade is first tilted to the desired angl e on the bevel scale befor e it is clamped in place. ...

  • Porter-Cable 33-890 - page 27

    27 PUSH STICK MAKE FROM 1/2" OR 3/4" WOOD OR THICKNESS LESS THAN WIDTH OF MA T’L. TO BE CUT CUT OFF HERE TO PUSH 1/4" WOOD CUT OFF HERE TO PUSH 1/2" WOOD NOTCH TO HELP PREVENT HAND FROM SLIPPING 1/2" SQUARES When ripping work less than 4 inches wide, a push stick should be used to complete the feed and could easily be mad ...

  • Porter-Cable 33-890 - page 28

    28 TROUBLESHOOTING GUIDE For assistance with your tool, visit our website at www .deltamachinery .com for a list of service centers or call the DEL T A Machniery help line at 1-800-223-7278 (In Canada call 1-800-463-3582). MAINTENANCE KEEP MACHINE CLEAN Periodically blow out all air passages with dry compressed air . All plastic parts should be cle ...

  • Porter-Cable 33-890 - page 29

    29 P AR TS, SERVICE OR W ARRANTY ASSIST ANCE All Delta Machines and accessories are manufactur ed to high quality standards and ar e serviced by a network of Porter -Cable • Delta Factory Service Centers and Delta Authorized Service Stations. T o obtain additional information regar ding your Delta quality product or to obtain parts, service, warr ...

  • Porter-Cable 33-890 - page 30

    30 NOTES ...

  • Porter-Cable 33-890 - page 31

    31 NOTES ...

  • Porter-Cable 33-890 - page 32

    The following are trademarks of POR TER-CABLE • DEL T A (Las siguientes son marcas registradas de POR TER-CABLE • DEL T A S.A.) (Les marques suivantes sont des marques de fabriquant de la POR TER-CABLE • DEL T A): Auto-Set ® , BAMMER ® , B.O.S.S. ® , Builder’ s Saw ® , Contractor’ s Saw ® , Contractor’ s Saw II™, Delta ® , DEL T ...

Fabricant Porter-Cable Catégorie Saw

Les documents que nous recevons du fabricant de l'appareilPorter-Cable 33-890 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Porter-Cable
- manuels d’utilisations 33-890
- fiches produit Porter-Cable
- dépliants
- ou étiquettes-énergie Porter-Cable 33-890
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Porter-Cable 33-890.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Porter-Cable 33-890, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Porter-Cable 33-890. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Porter-Cable 33-890.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Porter-Cable 33-890, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Porter-Cable 33-890 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Porter-Cable 33-890.

Le manuel d’utilisation complet Porter-Cable, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Porter-Cable 33-890 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Porter-Cable 33-890, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lPorter-Cable 33-890 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Porter-Cable 33-890 - qui devraient nous aider dans les premières étapes lors de l'utilisation Porter-Cable 33-890
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Porter-Cable 33-890
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Porter-Cable 33-890 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Porter-Cable 33-890?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Porter-Cable 33-890, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Porter-Cable 33-890 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)