Français dropdown-ico

Manuel d’utilisation Planet Technology 170S8FS

26 pages 2.6 mb
Télécharger

Aller à la page of 26

Summary
  • Planet Technology 170S8FS - page 1

    ...

  • Planet Technology 170S8FS - page 2

    Trademarks Copyrigh t  PLAN ET T echnolog y Corp. 2002. Contents subject to revis ion with out prio r notice. PLANET is a registered trademark of PLANET T echnology Corp. The information in this manual is su bject to cha nge withou t notice. All other t rademarks b elong to the ir respect ive owners. FCC Warning This equipment has been tested an ...

  • Planet Technology 170S8FS - page 3

    1 T able of Contents Chap ter 1 INTR ODU CTIO N 1 1.1 B rief ing 1 1.2 F ea ture s 1 Chap ter 2 UNP ACKI NG A ND I NST ALL 3 2.1 U npack ing 3 2.2 I nsta llati on 3 2.3 D ecid ing H ow t o In stal l th e S yste m 3 Chap ter 3 IDEN TIF YING FRO NT P ANEL 7 3.1 F ront P anel 7 3.2 L ED I ndica tors 7 Chap ter 4 CONF IGU RING THE SY STEM 9 4.1 C onfig ...

  • Planet Technology 170S8FS - page 4

    1 Chapter 1 Introduction 1.1 Brieng The Intelligent Media Converter Chassis WMC-1600R series provides 16-slot and one management system in the 19”-rack chassis. The management function enable network administrator to monitor the media converter connection status and congure the converter via SNMP agent, T elnet and W eb remotely or via RS-2 ...

  • Planet Technology 170S8FS - page 5

    2 3 ...

  • Planet Technology 170S8FS - page 6

    2 3 Chapter 2 UNP A CKING AND INST ALL This chapter provides unpacking and setup information for the Media Converter Chassis. 2.1 Unpacking Open the box of the WMC-1600R and carefully unpack it. The box should contain the following items: • One In telli gent Med ia Conve rter Cha ssis with one power s uppl y in stall ed • One RS -232 Cable • ...

  • Planet Technology 170S8FS - page 7

    4 5 2.3.1 Mounted to 19-inch standard rack Use the rack -mount brackets and screws to install the chassis into any EIA 19" standard rack. Step 1: Attach the brackets to each side of the chassis. Apply four screws to each side and secure them tightly . Step 2: Carefully position the chassis into the rack. Align the brackets to the side holes on ...

  • Planet Technology 170S8FS - page 8

    4 5 Step 3: Carefully slide in the module and fasten the hand screw clockwise by using hand or screwdriver until it is fully and rmly tted into the slot of the chassis. Insert the media converter module into an available slot and fasten the hand screw clockwise by using hand or screwdriver . 2.3.3 Connecting to Power (Power Supply) The chassi ...

  • Planet Technology 170S8FS - page 9

    6 7 2.3.4 Installing and Removing the Power Supply T o remove a power supply out the chassis, you have to loose the hand screw counter clockwise and pull out the power supply from the chassis. T o install a power supply to the chassis, you have to fasten the hand screw clockwise and slide in the power supply to the chassis. Y ou can slide in and ou ...

  • Planet Technology 170S8FS - page 10

    6 7 Chapter 3 IDENTIFYING FRONT P ANEL This section identies all the major components of the front panel. The front panel is shown, followed by a description of each panel feature. The indicator panel is described in detail in the next chapter . 3.1 Front Panel The gure below shows the front panels of the Management Module. The LED indicators ...

  • Planet Technology 170S8FS - page 11

    8 9 ...

  • Planet Technology 170S8FS - page 12

    8 9 Chapter 4 CONFIGURING THE SY STEM This chapter provides network managers and system administrators with information about how to congure the WMC-1600R via the Management interface. 4.1 Congure Through T erminal Emulator/TELNET Program 4.1.1 Console and T erminal Emulator program setting The WMC-1600R can be accessible using a terminal or ...

  • Planet Technology 170S8FS - page 13

    10 1 1 4.1.3 Management Setting Through T erminal Emulator There are three items in the Main Menu, System Function, Conguration and SNMP Conguration. 4.1.3.1 System Function There are three items in System Function menu, “Software Reboot, Factory Reset, and Image Update. 4.1.3.1.1 Software Reboot After conguring, it needs to reboot the s ...

  • Planet Technology 170S8FS - page 14

    10 1 1 There are four items in the Conguration menu, “General Conguration, System Conguration, Media Converter Chassis and Media Con verters. 4.1.3.2.1 General Conguration Hardware revision: noted the version of the hardware. BIOS revision: noted the version of the BIOS. Firmware revision: noted the version of the rmware. Change Pa ...

  • Planet Technology 170S8FS - page 15

    12 13 4.1.3.2.3 Media Converter Chassis The screen will show out the power status of the WMC-1600R. V stands for “yes” and X stands for “No” . Plug in: indicates if Power 1 or 2 was plugged in or not. Power Fail: indicates if the Power 1 or 2 is fail or not. Fan Fail: indicates if the F an 1 or 2 is fail or not. 4.1.3.2.4 Media Converters I ...

  • Planet Technology 170S8FS - page 16

    12 13 Device LLCF: Link Loss Carry F orward, “on” or “off” . Enable: to enable the link of the Device, “on” or “off” . Media 1 LLR: Link Loss Return, “on” or “off” . Auto: “ A” for Auto-Negotiation or “F” for “forced Mode” . Speed: to select the speed of the copper port, “10M” , “100M” or “1G” . Dup: ...

  • Planet Technology 170S8FS - page 17

    14 15 4.1.3.3 SNMP Conguration Get Community Name: to get the device community name (default = public). Set Community Name: to set the device community name (default = private). Trap Community Name: to authorize the device trap community name (default = public). Trap Host IP Address: to set the trap host IP address (same as monitoring station IP ...

  • Planet Technology 170S8FS - page 18

    14 15 4.2 Management through Web browser The WMC-1600R is accessible using a Web browser (IE explorer , Netscape Communications, etc.) to open up the chassis monitoring system. The default IP Address for the chassis system is “192.168.1.1” , and the default Login name and password is both “root” . After enter its web interface, the Home P a ...

  • Planet Technology 170S8FS - page 19

    16 17 4.2.1 System Function There are four items in System Function menu, “Software Reboot, Factory Reset, Image Update and Conguration Update. 4.2.1.1 Software Reboot Reboot the management module in order to run the new setting properly . 4.2.1.2 Factory Reset This function is to set the device back to the default setting in case of the messy ...

  • Planet Technology 170S8FS - page 20

    16 17 System Name: to authorize the device system name. Location: to show the WMC-1600R where it is located. Refresh time: to set the refreshing time of the device through the web. NOTE: After configuring the system device, need to press the save button to save the setting. 4.2.2.2 System Conguration MAC Address: will show out the MAC address of ...

  • Planet Technology 170S8FS - page 21

    18 19 Warm Start trap: to set the trap when the device had been reset (default = enable). Authentication Fail Trap: to set the warning trap when the community name of the device and workstation are different (default = enable). Power Fail Trap: to set the Power F ail T rap (default = enable). Fan Fail Trap: to set the F an fail trap (default = enab ...

  • Planet Technology 170S8FS - page 22

    18 19 4.2.2.5 Redundant Backup Setting The redundant function is to change the master line to the slave line in case of the linking fails happen. The Redundant functions were set xed, the master slot is slot 1(odd number slot) and the slave slot is slot 2(even number slot), and there are eight redundant groups in all. The “ Act ” will indica ...

  • Planet Technology 170S8FS - page 23

    20 21 ...

  • Planet Technology 170S8FS - page 24

    20 21 Chapter 5 TECHNICAL SPECIFICA TIONS Chassis System Capacity Sixteen bays for housing up to sixteen media converters Material Steel Power One power supply provided, hot-swappable *A second power supply for load-sharing is optional, also hot- swappable Cooling T wo fans mounted together with the power supply or alone at the rear Dimensions W415 ...

  • Planet Technology 170S8FS - page 25

    22 Management Module Standards IEEE802.3 10Base- T Ethernet IEEE802.3u 100 Base- TX F ast Ethernet IEEE802.3x flow control Protocol CSMA/CD Data T ransfer Rate Ethernet: 10Mbps (half duplex), 20Mbps (full duplex)F ast Ethernet: 100Mbps (half duplex), 200Mbps (full duplex) LED Indicators Power On, Power F ail, F an F ail, MGM, Console, LNK/ACT Cable ...

  • Planet Technology 170S8FS - page 26

    22 Part No.:EM-WMCv1 ...

Fabricant Planet Technology Catégorie Cable Box

Les documents que nous recevons du fabricant de l'appareilPlanet Technology 170S8FS peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Planet Technology
- manuels d’utilisations 170S8FS
- fiches produit Planet Technology
- dépliants
- ou étiquettes-énergie Planet Technology 170S8FS
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Planet Technology 170S8FS.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Planet Technology 170S8FS, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Planet Technology 170S8FS. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Planet Technology 170S8FS.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Planet Technology 170S8FS, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Planet Technology 170S8FS par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Planet Technology 170S8FS.

Le manuel d’utilisation complet Planet Technology, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Planet Technology 170S8FS - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Planet Technology 170S8FS, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lPlanet Technology 170S8FS qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Planet Technology 170S8FS - qui devraient nous aider dans les premières étapes lors de l'utilisation Planet Technology 170S8FS
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Planet Technology 170S8FS
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Planet Technology 170S8FS dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Planet Technology 170S8FS?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Planet Technology 170S8FS, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Planet Technology 170S8FS il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)