Français dropdown-ico

Manuel d’utilisation SkyLink SA-001S

20 pages 0.61 mb
Télécharger

Aller à la page of 20

Summary
  • SkyLink SA-001S - page 1

    Model: SA-001S User’ s Instructions W ireless External Alarm ...

  • SkyLink SA-001S - page 2

    1 TABLE OF cONTENT INTRODUCTION ................................................................................................... INSTALLATION .............................................................................................. PROGRAMMING – LEARN REMOTE OR SENSORS OR CONTROL PANEL ....................... ERASE REMOTE OR SENSOR OR CON ...

  • SkyLink SA-001S - page 3

    2 INTrOducTION Congratulations on purchasing the Skylink Wireless External Alarm SA-001 Series. The SA-001 Series provide you with a piercing siren and powerful features yet ease to use. You will nd the installation to be simple and be able to get the unit up and running easily. The following items are included in this package: - One Wireless Ex ...

  • SkyLink SA-001S - page 4

    3 - Set Compatibility Jumper: Refer to the following table to setup the Wireless External Alarm to work with different Skylink’s Security System or Sensors. To select, you will see a jumper connector marked “J2” as shown below. Use a paper clip to remove the jumper connector and re-locate to the proper posts. - Insert 3 AA-size batteries (not ...

  • SkyLink SA-001S - page 5

    4 cAuTION: The adaptor as a disconnect devices: − the socket-outlet shall be installed near the equipment and shall be easily accessible. In order for the remote or sensor or control panel to communicate with the Exter- nal Wireless Alarm properly, this need be programmed into the Wireless External Alarm previously. Follow the brief instructions ...

  • SkyLink SA-001S - page 6

    5 3B – Learn motion sensor to the Wireless External Alarm: - Press and hold the Learn button on the Wireless External Alarm for 2 seconds and then release. The Learn/Set LED will ash. - Activate the motion sensor by pressing the “Test/Set” button on the motion sensor. This “Test/Set” button is located inside the battery compartment. - ...

  • SkyLink SA-001S - page 7

    6 Mute button 3C – Learn door/window sensor to the Wireless External Alarm: - Press and hold the Learn button on the Wireless External Alarm for 2 seconds and then release. The Learn/Set LED will ash. - Activate the Door/Window Sensor, by separating the magnets to send the signal. - You will hear 2 beeps and the LEDs will ash twice indicati ...

  • SkyLink SA-001S - page 8

    7 To erase unwanted remote(s) or sensor(s) or control panel(s) from the Wireless External Alarm will erase all learned devices from the Wireless External Alarm. - Press and hold the Learn/Set button on the Wireless External Alarm for 8 seconds. - While holding the Learn/Set button on the Wireless External Alarm until the Learn/Set LEDs turn on. You ...

  • SkyLink SA-001S - page 9

    8 The Wireless External Alarm can be programmed to react 2 arming sequences when it receives the signal from the sensor. In order to arm the Wireless External Alarm, the remote (optional) must be programmed to the Wireless External Alarm. You may arm the Wireless External Alarm in 2 different sequences: 6A – Arm Home Sequence: This setting is use ...

  • SkyLink SA-001S - page 10

    9 - You will hear 1 beep and the LEDs will ash once indicating the Wireless External Alarm is being counted to Away mode. - After 30 seconds, you will hear 2 beeps and the LEDs will ash twice indicating the Wireless External Alarm in Away mode. 6C – Disarm - Pressing the DISARM button on the remote will disarm the Wireless External Alarm in ...

  • SkyLink SA-001S - page 11

    10 The Wireless External Alarm is designed to work with the Skylink security control panel such as AM-001, ML-001 and SC-001. Put the control panel that you plan to program into programming mode. Refer to the User’s Instructions of that control panel. 7A – Learn control panel AM-001 or ML-001 to the Wireless External Alarm: - Press and hold the ...

  • SkyLink SA-001S - page 12

    11 You may connect your existing alarm system with the Wireless External Alarm so that the Wireless External Alarm will be triggered by your alarm system. There are 2 ways you can connect your Wireless External Alarm with your existing alarm system. The input terminals (INPUT1 or INPUT2) can be a Normally Open (NO) momentary dry contact or the DC v ...

  • SkyLink SA-001S - page 13

    12 You can enable or disable the Alert Notication. When it is set to enable, the Wireless External Alarm will beep when arm or disarm or during the entry/exit countdown period. When it is set to disable, the Wireless External Alarm will not beep when arm or disarm or during the entry/exit countdown period. However, the LED will remain ashing ...

  • SkyLink SA-001S - page 14

    13 When the battery power is being reduced, the Wireless External Alarm will emit 3 beeps when the remote arm or disarm the unit. It is time to replace the batteries or recharge the battery pack (rechargeable battery only) as soon as the low battery signal appears. Ensure all the batteries are replaced altogether at the same time. The Wireless Exte ...

  • SkyLink SA-001S - page 15

    14 Your Wireless External Alarm requires few simple maintenance to ensure its con - tinued reliability and operation. - The solar panel on the top housing should be cleaned using the soft and damp cloth. This will ensure the solar panel receives all the available light. - Test the Wireless External Alarm periodically to ensure the unit is working. ...

  • SkyLink SA-001S - page 16

    15 Questions Solutions Why the Wireless External Alarm does not respond to the sensors or remote? You must program the sensors or remote to the Wireless External Alarm before they can work together. Why I can’t arm my system? Make sure none of the sensors are trig- gered. For example, the door/window sensor should be in close status. Why isn’t ...

  • SkyLink SA-001S - page 17

    16 Fcc This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. WArNINg: Changes or modications to this unit not expressly appro ...

  • SkyLink SA-001S - page 18

    17 WArrANTy If, within one year from date of purchase, this product should become defective (except battery), due to faulty workmanship or materials, it will be repaired or replaced, without charge. Proof of purchase and a Return Authorization Number are required. Ic Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux ap- ...

  • SkyLink SA-001S - page 19

    18 cusTOmEr sErVIcE If you would like to - nd out the up-to-date specications - know more about features and applications - download documents, i.e. user’s instructions - order Skylink products or if you have difculty getting the products to work, please: 1. visit our FAQ section at www.skylinkhome.com, or 2. email us at support@skylinkh ...

  • SkyLink SA-001S - page 20

    19 101Y035 DEC,2012 ...

Fabricant SkyLink Catégorie Medical Alarms

Les documents que nous recevons du fabricant de l'appareilSkyLink SA-001S peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques SkyLink
- manuels d’utilisations SA-001S
- fiches produit SkyLink
- dépliants
- ou étiquettes-énergie SkyLink SA-001S
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation SkyLink SA-001S.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation SkyLink SA-001S, manuels d’entretien, brefs manuels ou manuels de l’utilisateur SkyLink SA-001S. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit SkyLink SA-001S.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil SkyLink SA-001S, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser SkyLink SA-001S par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs SkyLink SA-001S.

Le manuel d’utilisation complet SkyLink, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel SkyLink SA-001S - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières SkyLink SA-001S, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lSkyLink SA-001S qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil SkyLink SA-001S - qui devraient nous aider dans les premières étapes lors de l'utilisation SkyLink SA-001S
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de SkyLink SA-001S
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service SkyLink SA-001S dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de SkyLink SA-001S?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec SkyLink SA-001S, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec SkyLink SA-001S il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)